Datasheet

HIGH VOLTAGE
POWER SUPPLY
C12446 SERIES
The C12446 series is an on-board type high voltage power supply module, especially designed for photomultiplier
tubes. This power supply can drive several photomultipliers used for multi-channel measurement. The design offers good performance and complete fail-safe protection.
FEATURES
●High output power (1 kV / 10 mA)
●Compact and lightweight
●High voltage and current monitor output
●Low Ripple / Noise
SPECIFICATIONS
Parameter
C12446-12
C12446-52
+24 ± 1.2
55
550
Input voltage
Typ.
with no load
with full load Typ.
Variable output voltage range
0 to -1000
0 to +1000
Specification guaranteed output voltage range
-200 to -1000
+200 to +1000
Output current
Max.
10
Line regulation against ±1.2 V input change AB Typ.
±0.01
Load regulation against 0 % to 100 %
Typ.
±0.01
load change A
Ripple / Noise (p-p) AB
Typ.
50
Output voltage control
By external controlling voltage (0 V to +5 V) or external potentiometer (50 kΩ)
Controlling voltage input impedance
640
Typ.
+5.3
Reference voltage output
Typ.
Output voltage setting (Absolute value)
Controlling voltage × 200
Typ.
150
Output voltage rise time (0 % ➝ 99 %) AB Typ.
Temperature coefficient AB
±0.005
Typ.
High voltage monitor output
0 V to +5 V (Output impedance 10 kΩ), 5 mV/V
Current monitor output
0 V to +5 V (Output impedance 10 kΩ), 0.5 V/mA
ON / OFF input
TTL positive logic
30
ON / OFF input impedance
0 to +50
Operating ambient temperature AB
Operating ambient humidity C
Below 85
-20 to +60
Storage temperature
Below 85
Storage humidity C
Weight
100
Typ.
units protected against reversed power input, reversed / excessive controlling
Protective functions
voltage input, continuous overloading / short circuit in output
Input current A
AAt maximum output voltage.
BAt maximum output current.
Unit
V
mA
V
V
mA
%
%
mV
—
kΩ
V
V
ms
%/°C
—
—
—
kΩ
°C
%
°C
%
g
—
CNo condensation
Subject to local technical requirements and regulations, availability of products included in this promotional material may vary. Please consult with our sales office.
Information furnished by HAMAMATSU is believed to be reliable. However, no responsibility is assumed for possible inaccuracies or omissions. Specifications are
subject to change without notice. No patent rights are granted to any of the circuits described herein. ©2016 Hamamatsu Photonics K.K.
HIGH VOLTAGE POWER SUPPLY
C12446 SERIES
Figure 1: Connection diagrams
●Output voltage control
by external voltage
●Output voltage control
by external potentiometer
LOAD
LOAD
!0
o
!0
640
kΩ
640
kΩ
10
kΩ
q
w
e
+24 V
t
r
y
10
kΩ
10
kΩ
u
i
V
V
q
w
e
t
r
MIN.
0 V to +5 V *
+24 V
TTL logic High: HV-ON
TTL logic Low : HV-OFF
10
kΩ
y
u
i
MAX.
V
V
50 kΩ
y Vref +5.3 V Typ.
u CURRENT MONITOR OUT
i HV MONITOR OUT
o HV GND
!0 HV OUT
* The instability in the external controlling voltage should be
minimized as it directly affects the output voltage quality.
** Never connect the pin number 2 and 4 directly and
externally.
NOTE: In the case of an open state at pin e, the module
will have no high voltage output. If you don't use
HV-ON / OFF function at pin e, you can make the
module work by connecting a 10 kΩ (1/4 W or
more) resister between pin e and pin q.
TTL logic High: HV-ON
TTL logic Low : HV-OFF
Figure 2: Output voltage controlling characteristic
C12446-12
PIN ASSIGNMENT
q Vcc +24 V
w Vcc GND **
e ON / OFF IN
r Vcont GND **
t Vcont
o
TACCC0158EB
Figure 3: Example of ripple / noise reduction circuit
C12446-52
TACCB0127EA
+1200
-1200
1.5 kΩ (1/4 W)
1
+24 V
+1000
-800
+800
-600
+600
-400
+400
-200
+200
0.1 µF
(35 V)
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
-1000
220 µF
(35 V)
C12446
SERIES
+
!0
2
GND
+HV OUTPUT
0.068 µF
(2 kV)
GND
* The ripple noise can be reduced to approx. 1/3 by
adding capacitors as illustrated above.
TACCC0162EB
0
0
1
0
2
3
4
5 5.3
6
CONTROLLING VOLTAGE (V)
Figure 4: Dimensional outline (Unit: mm)
62
1
4
0.5
4
32
1
2
3
4
5
6
7
8
10
3.96
9
22.5
1.5
1.14
3.96 × 7
8×
2
15
45
PIN ASSIGNMENT
q Vcc +24 V
w Vcc GND
e ON / OFF IN
r Vcont GND
t Vcont
y Vref +5.3 V Typ.
u CURRENT MONITOR OUT
i HV MONITOR OUT
o HV GND
!0 HV OUT
* The housing is internally connected to pin 2.
20
TACCA0315EC
HAMAMATSU PHOTONICS K.K.
www.hamamatsu.com
HAMAMATSU PHOTONICS K.K., Electron Tube Division
314-5, Shimokanzo, Iwata City, Shizuoka Pref., 438-0193, Japan, Telephone: (81)539/62-5248, Fax: (81)539/62-2205
U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater. N.J. 08807-0910, U.S.A., Telephone: (1)908-231-0960, Fax: (1)908-231-1218 E-mail: [email protected]
Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49)8152-375-0, Fax: (49)8152-2658 E-mail: [email protected]
France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: (33)1 69 53 71 00, Fax: (33)1 69 53 71 10 E-mail: [email protected]
United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44)1707-294888, Fax: (44)1707-325777 E-mail: [email protected]
North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 SE-164 40 Kista, Sweden, Telephone: (46)8-509-031-00, Fax: (46)8-509-031-01 E-mail: [email protected]
Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, 1 int. 6, 20020 Arese (Milano), Italy, Telephone: (39)02-93581733, Fax: (39)02-93581741 E-mail: [email protected]
TACC1070E01
China: Hamamatsu Photonics (China) Co., Ltd.: B1201 Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86)10-6586-6006, Fax: (86)10-6586-2866 E-mail: [email protected]
Taiwan: Hamamatsu Photonics Taiwan Co., Ltd.: 8F-3, No.158, Section2, Gongdao 5th Road, East District, Hsinchu, 300, Taiwan R.O.C. Telephone: (886)03-659-0080, Fax: (886)07-811-7238 E-mail: [email protected]
APR. 2016 IP