AS1363 - Demo Board Manual Low Dropout Regulator Demo Board Manual AS1363 500mA, Low-Dropout Linear Voltage Regulator www.austriamicrosystems.com/LDO/AS1363 www.austriamicrosystems.com Revision 1.00 1-5 AS1363 - Demo Board Manual Low Dropout Regulator General Description Board Description H K E A D C B A L M G I F D C N B Figure 1: Board Description - Connectors J O Figure 2: Board Description – Measurement Points Connector Description Label Name Description Info A B VIN GND Supply Voltage Ground Supply voltage range from 2.0V to 5.5V C EN Active High Enable Input D VOUT Output Voltage Set the digital input “high” for normal operation. For shutdown, set “low” Output voltage range from 1.2V to 4.5V (fixed) Output voltage range from 1.2V to 5.3V (adjustable) Measurement Point Description Label Name Description E F G H I J K L VIN GND EN POK BP SET VOUT Load Supply Voltage Ground Active High Enable Input Open Drain POK Output BP (fixed Vout version) SET (adjustable Vout version) Output Voltage External load Info Measurement Points ON: The AS1363 is enabled M N O EN R1 R2 www.austriamicrosystems.com OFF: The AS1363 is disabled Enable Resistor divider for adjustable Vout version Revision 1.00 No Jumper: Connect a valid enable signal via external connector “C”. R1 between Vout and SET R2 between SET and GND 2-5 AS1363 - Demo Board Manual Low Dropout Regulator Getting Started The AS1363 Demoboard is designed to work with the AS1363 fixed output voltage version. The AS1363 fixed Vout version is available with 1.5V, 1.8V, 3.0V, 3.3V and 4.5V. The AS1363-AD Demoboard is designed to work with the AS1363 adjustable output voltage version. The AS1363-AD adjustable Vout version has a valid Vout range from 1.2V to 5.3V. This Vout is adjustable via the resistor divider R1/R2. A value for R2 in the range of 25kΩ to 100kΩ should be sufficient. To use the factory preset Vout of 2.5V connect SET directly to GND (R1 = open; R2 = 0Ω). Bill of Materials Ref. Function Value Description Manufacturer Cin Input Capacitor Cout Output Capacitor 1µF 1206 / X7R / 10V diverse 2.2µF 1206 / X7R / 10V diverse CBP* Bypass Capacitor 0805/X7R diverse RPOK POK pull-up resistor 100kΩ 0805 diverse U1 LDO ASRx SOT23-6pin Austriamicrosystems AG 10nF Mfg. Order Nr. AS1363-BSTT-xx *) only for fixed Vout version www.austriamicrosystems.com Revision 1.00 3-5 AS1363 - Demo Board Manual Low Dropout Regulator Layout of Demo Board Board schematics and layout Figure 3: Schematics (fixed Vout) Figure 4: Schematics (adjustable Vout) Figure 5: Top + Bottom Layer (fixed Vout) Figure 6: Top + Bottom Layer (adjustable Vout) www.austriamicrosystems.com Revision 1.00 4-5 AS1363 - Demo Board Manual Low Dropout Regulator Copyright Copyright © 1997-2010, austriamicrosystems AG, Tobelbaderstraße 30, 8141 Unterpremstätten - Graz, Austria Europe. Trademarks Registered ®. All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. All products and companies mentioned are trademarks or registered trademarks of their respective companies. Disclaimer Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Austriamicrosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for each application. For shipments of less than 100 parts the manufacturing flow might show deviations from the standard production flow, such as test flow or test location. The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services. Contact Information Headquarters austriamicrosystems AG Tobelbaderstraße 30 A-8141 Unterpremstätten - Graz, Austria T. +43 (0) 3136 500 0 F. +43 (0) 3136 5692 For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com/contact www.austriamicrosystems.com Revision 1.00 5-5