DATASHEET

IGNS
EW DES
N
R
O
F
NDED
EM ENT
C OM M E
REPL AC
D
E
NO T R E
D
N
ter at
E
M
port Cen /tsc
ECOMSheet
p
u
S
l
NO RData
a
m
nic
tersil.co
our Tech
contact ERSIL or www.in
T
1-888-IN
EL1516, EL1516A
May 3, 2007
Dual Ultra Low Noise Amplifier
Features
The EL1516 is a dual, ultra low noise amplifier, ideally suited
to line receiving applications in ADSL, VDSL, and home
PNA designs. With low noise specification of just 1.3nV/Hz
and 1.5pA/Hz, the EL1516 is perfect for the detection of
very low amplitude signals.
• EL2227 upgrade replacement
The EL1516 features a -3dB bandwidth of 350MHz @ AV = -1
and is gain-of-2 stable. The EL1516 also affords minimal
power dissipation with a supply current of just 5.5mA per
amplifier. The amplifier can be powered from supplies ranging
from 5V to 12V.
• Bandwidth (-3dB) of 250MHz @ AV = +2
The EL1516A incorporates an enable and disable function to
reduce the supply current to 5nA typical per amplifier,
allowing the EN pins to float or apply a low logic level will
enable the amplifiers.
The EL1516 is available in space-saving 8 Ld MSOP and
industry-standard 8 Ld SOIC packages and the EL1516A is
available in a 10 Ld MSOP package. All are specified for
operation over the -40°C to +85°C temperature range.
Pinouts
FN7328.2
• Voltage noise of only 1.3nV/Hz
• Current noise of only 1.5pA/Hz
• Bandwidth (-3dB) of 350MHz @ AV = -1
• Gain-of-2 stable
• Just 5.5mA per amplifier
• 100mA IOUT
• Fast enable/disable (EL1516A only)
• 5V to 12V operation
• Pb-free plus anneal available (RoHS compliant)
Applications
• ADSL receivers
• VDSL receivers
• Home PNA receivers
EL1516
(8 LD SOIC, 8 LD MSOP)
TOP VIEW
VOUTA 1
VINA- 2
8 VS+
7 VOUTB
+
VINA+ 3
6 VINB+
VS- 4
• Ultrasound input amplifiers
• Wideband instrumentation
• Communications equipment
• AGC and PLL active filters
• Wideband sensors
5 VINB+
EL1516A
(10 LD MSOP)
TOP VIEW
10 VINA-
VINA+ 1
ENA 2
9 VOUTA
VS- 3
8 VS+
ENB 4
7 VOUTB
6 VINB-
VINB+ 5
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2005, 2006, 2007. All Rights Reserved.
All other trademarks mentioned are the property of their respective owners.
EL1516, EL1516A
Ordering Information
PART NUMBER
PART MARKING
TAPE AND REEL
PACKAGE
PKG. DWG. #
EL1516IY
BAAHA
-
8 Ld MSOP (3.0mm)
MDP0043
EL1516IY-T13
BAAHA
13”
8 Ld MSOP (3.0mm)
MDP0043
EL1516IY-T7
BAAHA
7”
8 Ld MSOP (3.0mm)
MDP0043
EL1516IYZ (Note)
BAAAY
-
8 Ld MSOP (Pb-free) (3.0mm)
MDP0043
EL1516IYZ-T13 (Note)
BAAAY
13”
8 Ld MSOP (Pb-free) (3.0mm)
MDP0043
EL1516IYZ-T7 (Note)
BAAAY
7”
8 Ld MSOP (Pb-free) (3.0mm)
MDP0043
EL1516IS
1516IS
-
8 Ld SOIC (150 mil)
MDP0027
EL1516IS-T13
1516IS
13”
8 Ld SOIC (150 mil)
MDP0027
EL1516IS-T7
1516IS
7”
8 Ld SOIC (150 mil)
MDP0027
EL1516ISZ (Note)
1516ISZ
-
8 Ld SOIC (Pb-free) (150 mil)
MDP0027
EL1516ISZ-T13 (Note)
1516ISZ
13”
8 Ld SOIC (Pb-free) (150 mil)
MDP0027
EL1516ISZ-T7 (Note)
1516ISZ
7”
8 Ld SOIC (Pb-free) (150 mil)
MDP0027
EL1516AIY
BBDAA
-
10 Ld MSOP (3.0mm)
MDP0043
EL1516AIY-T13
BBDAA
13”
10 Ld MSOP (3.0mm)
MDP0043
EL1516AIY-T7
BBDAA
7”
10 Ld MSOP (3.0mm)
MDP0043
EL1516AIYZ (Note)
BBEAA
-
10 Ld MSOP (Pb-free) (3.0mm)
MDP0043
EL1516AIYZ-T13 (Note)
BBEAA
13”
10 Ld MSOP (Pb-free) (3.0mm)
MDP0043
EL1516AIYZ-T7 (Note)
BBEAA
7”
10 Ld MSOP (Pb-free) (3.0mm)
MDP0043
NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
2
FN7328.2
May 3, 2007
EL1516, EL1516A
Absolute Maximum Ratings (TA = +25°C)
Thermal Information
Supply Voltage between VS+ and VS- . . . . . . . . . . . . . . . . . . . . .14V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . VS- -0.3V, VS +0.3V
Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 40mA
Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are
at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
Electrical Specifications
PARAMETER
VS+ = +2.5V, VS- = -2.5V, RL = 500 and CL = 3pF to 0V, RF = RG = 620, VCM = 0V, and TA = +25°C,
Unless Otherwise Specified.
DESCRIPTION
CONDITIONS
MIN
TYP
MAX
UNIT
-0.2
+3
mV
INPUT CHARACTERISTICS
VOS
Input Offset Voltage
TCVOS
Average Offset Voltage Drift
IB
Input Bias Current
IOS
VCM = 0V
-0.3
VCM = 0V
µV/°C
6.5
9
µA
Input Offset Current
50
500
nA
RIN
Input Impedance
2
M
CIN
Input Capacitance
1.6
pF
CMIR
Common-Mode Input Range
CMRR
Common-Mode Rejection Ratio
for VIN from -4.7V to 5.4V
85
105
dB
AVOL
Open-Loop Gain
VO ±1.25V
70
75
dB
en
Voltage Noise
f = 100kHz
1.24
nV/Hz
in
Current Noise
f = 100kHz
1.5
pA/Hz
RL = 500
1.45
1.35
V
RL = 150
1.37
1.25
V
-1.3
+1.7
V
OUTPUT CHARACTERISTICS
VOL
VOH
ISC
Output Swing Low
Output Swing High
Short Circuit Current
RL = 500
1.5
1.6
V
RL = 150
1.4
1.5
V
RL = 10
60
75
mA
75
80
dB
POWER SUPPLY PERFORMANCE
PSRR
Power Supply Rejection Ratio
VS is moved from ±5.4V to ±6.6V
IS ON
Supply Current Enable (Per Amplifier)
No load
5.7
7
mA
IS OFF
Supply Current Disable (Per Amplifier)
(EL1516A)
I+ (DIS)
2
20
µA
TC IS
IS Temperature Coefficient
VS
Operating Range
I- (DIS)
-21
-16
µA
32
µA/°C
5
12
V
DYNAMIC PERFORMANCE
SR
Slew Rate
VO = ±1.25V square wave, measured 25% to 75%
TC SR
SR Temperature Coefficient
tS
Settling to 0.1% (AV = +2)
BW1
BW2
110
V/µs
0.5
V/µs/°C
AV = +2, VO = ±1V
25
ns
-3dB Bandwidth
AV = -1, RF = 100
320
MHz
-3dB Bandwidth
AV = +2, RF = 100
200
MHz
3
80
FN7328.2
May 3, 2007
EL1516, EL1516A
Electrical Specifications
PARAMETER
VS+ = +2.5V, VS- = -2.5V, RL = 500 and CL = 3pF to 0V, RF = RG = 620, VCM = 0V, and TA = +25°C,
Unless Otherwise Specified. (Continued)
DESCRIPTION
CONDITIONS
MIN
TYP
MAX
UNIT
HD2
2nd Harmonic Distortion
f = 1MHz, VO = 2VP-P, RL = 100
90
dBc
HD3
3rd Harmonic Distortion
f = 1MHz, VO = 2VP-P, RL = 100
95
dBc
ENABLE (EL1516AIY ONLY)
tEN
Enable Time
125
ns
tDIS
Disable Time
336
ns
IIHEN
EN Pin Input High Current
EN = VS+
18
µA
IILEN
EN Pin Input Low Current
EN = VS-
10
nA
VIHEN
EN Pin Input High Voltage for
Power-down
VS+ -1
V
VIHEN
EN Pin Input Low Voltage for Power-up
VS- +3
V
Electrical Specifications
PARAMETER
VS+ = +6V, VS- = -6V, RL = 500 and CL = 3pF to 0V, RF = RG = 620, VCM = 0V, and TA = +25°C,
Unless Otherwise Specified.
DESCRIPTION
CONDITIONS
MIN
TYP
MAX
UNIT
0.1
3
mV
INPUT CHARACTERISTICS
VOS
Input Offset Voltage
TCVOS
Average Offset Voltage Drift
IB
Input Bias Current
IOS
VCM = 0V
-0.3
VCM = 0V
µV/°C
6.5
9
µA
Input Offset Current
50
500
nA
RIN
Input Impedance
12
M
CIN
Input Capacitance
1.6
pF
CMIR
Common-Mode Input Range
CMRR
Common-Mode Rejection Ratio
for VIN from -4.7V to 5.4V
90
110
dB
AVOL
Open-Loop Gain
VO ±2.5V
75
80
dB
en
Voltage Noise
f = 100kHz
1.24
nV/Hz
in
Current Noise
f = 100kHz
1.5
pA/Hz
RL = 500
-4.8
-4.7
V
RL = 150
-4.6
-4.5
V
-4.5
+5.5
V
OUTPUT CHARACTERISTICS
VOL
VOH
ISC
Output Swing Low
Output Swing High
Short Circuit Current
RL = 500
4.8
4.9
V
RL = 150
4.5
4.7
V
RL = 10
110
160
mA
75
85
dB
POWER SUPPLY PERFORMANCE
PSRR
Power Supply Rejection Ratio
VS is moved from ±5.4V to ±6.6V
IS ON
Supply Current Enable (Per Amplifier)
No load
IS OFF
Supply Current Disable (Per Amplifier) I+ (DIS)
(EL1516A)
I- (DIS)
TC IS
IS Temperature Coefficient
VS
Operating Range
4
-19
5
5.8
7
mA
2
5
µA
-16
µA
32
µA/°C
12
V
FN7328.2
May 3, 2007
EL1516, EL1516A
Electrical Specifications
PARAMETER
VS+ = +6V, VS- = -6V, RL = 500 and CL = 3pF to 0V, RF = RG = 620, VCM = 0V, and TA = +25°C,
Unless Otherwise Specified. (Continued)
DESCRIPTION
CONDITIONS
MIN
TYP
MAX
UNIT
VO = ±2.5V square wave, measured 25% to 75%
90
128
V/µs
0.5
V/µs/°C
DYNAMIC PERFORMANCE
SR
Slew Rate
TC SR
SR Temperature Coefficient
tS
Settling to 0.1% (AV = +2)
AV = +2, VO = ±1V
20
ns
BW1
-3dB Bandwidth
AV = -1, RF = 100
350
MHz
BW2
-3dB Bandwidth
AV = +2, RF = 100
250
MHz
HD2
2nd Harmonic Distortion
f = 1MHz, VO = 2VP-P, RL = 500
125
dBc
f = 1MHz, VO = 2VP-P, RL = 150
117
dBc
f = 1MHz, VO = 2VP-P, RL = 500
115
dBc
f = 1MHz, VO = 2VP-P, RL = 150
110
dBc
HD3
3rd Harmonic Distortion
ENABLE (EL1516AIY ONLY)
tEN
Enable Time
125
ns
tDIS
Disable Time
336
ns
IIHEN
EN Pin Input High Current
EN = VS+
17
20
µA
IILEN
EN Pin Input Low Current
EN = VS-
7
20
nA
VIHEN
EN Pin Input High Voltage for
Power-down
VS+ -1
V
VIHEN
EN Pin Input Low Voltage for Power-up
VS- +3
V
Typical Performance Curves
4
VS = ±6V
AV = +2
2 RL = 500
0
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
4
RF = 100
RF = 348
-2
RF = 1k
RF = 619
-4
-6
1M
10M
100M
1G
FREQUENCY (Hz)
FIGURE 1. NON-INVERTING FREQUENCY RESPONSE FOR
VARIOUS RF
5
VS = ±6V
RF = 348
2 RL = 500
0
-2
AV = 10
AV = 5
AV = 2
-4
-6
1M
10M
100M
1G
FREQUENCY (Hz)
FIGURE 2. NON-INVERTING FREQUENCY RESPONSE (GAIN)
FN7328.2
May 3, 2007
EL1516, EL1516A
Typical Performance Curves
(Continued)
4
VS = ±6V
AV = +2
2 RL = 500
RF = 619
CL = 22pF
CL = 12pF
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
4
CL = 4.7pF
0
-2
CL = 1pF
CL = 0pF
-4
-6
1M
10M
100M
VS = ±6V
AV = +2
2 RF = 619
0
VIN = 20mVP-P
VIN = 500mVP-P
VIN = 1VP-P
VIN = 2VP-P
10M
100M
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
VIN = 100mVP-P
0
VS = ±6V
AV = -1
2 RL = 500
RF = 420
-2
RF = 620
-4
RF = 1k
-6
1M
1G
100M
1G
FIGURE 6. INVERTING FREQUENCY RESPONSE FOR
VARIOUS RF
4
4
VS = ±6V
RF = 420
2 RL = 500
0
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
10M
FREQUENCY (Hz)
FIGURE 5. NON-INVERTING FREQUENCY RESPONSE FOR
VARIOUS INPUT SIGNAL LEVELS
AV = -1
AV = -2
-6
1M
RF = 100
0
FREQUENCY (Hz)
-4
1G
4
VS = ±6V
AV = +2
2 RL = 500
RF = 348
-2
100M
FIGURE 4. NON-INVERTING FREQUENCY RESPONSE FOR
VARIOUS RL
4
-6
1M
10M
FREQUENCY (Hz)
FIGURE 3. NON-INVERTING FREQUENCY RESPONSE FOR
VARIOUS CL
-4
RL = 50
-4
FREQUENCY (Hz)
-2
RL = 100
-2
-6
1M
1G
RL = 500
AV = -10
AV = -5
10M
100M
1G
FREQUENCY (Hz)
FIGURE 7. INVERTING FREQUENCY RESPONSE (GAIN)
6
VS = ±6V
AV = -1
2 RL = 500
RF = 420
CL = 18pF
CL = 12pF
0
-2
CL = 2pF
-4
-6
1M
10M
100M
1G
FREQUENCY (Hz)
FIGURE 8. INVERTING FREQUENCY RESPONSE FOR
VARIOUS CL
FN7328.2
May 3, 2007
EL1516, EL1516A
Typical Performance Curves
2
VS = ±6V
AV = -1
RL = 500
RF = 420
5
VIN = 280mVPP
0
VIN = 20mVPP
VIN = 1.4VPP
-2
VIN= 2.8VPP
-4
-6
1M
10M
100M
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
4
(Continued)
3
VS = ±2.5V
AV = -1
RL = 500
RF = 422
1
-1
RF = 619
RF = 1k
-3
-5
100k
1G
1M
FREQUENCY (Hz)
5
VS = ±2.5V
RF = 422
RL = 500
AV = -2
1
-1
AV = -1
AV = -5
-3
AV = -10
-5
100k
1M
10M
100M
3
1
RL = 500
-1
RL = 50
-3
RL = 100
-5
100k
1G
1M
5
CL = 18pF
CL = 15pF
1
CL = 12pF
-1
CL = 10pF
CL = 0pF
-3
-5
100k
1M
10M
100M
1G
FREQUENCY (Hz)
FIGURE 13. INVERTING FREQUENCY RESPONSE FOR
VARIOUS CL
7
100M
1G
FIGURE 12. INVERTING FREQUENCY RESPONSE FOR
VARIOUS RL
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
3
10M
FREQUENCY (Hz)
FIGURE 11. INVERTING FREQUENCY RESPONSE FOR
VARIOUS AV
VS = ±2.5V
AV = -1
RF = 420
RL = 500
1G
VS = ±2.5V
AV = -1
RF = 420
FREQUENCY (Hz)
5
100M
FIGURE 10. INVERTING FREQUENCY RESPONSE FOR
VARIOUS RF
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
3
10M
FREQUENCY (Hz)
FIGURE 9. INVERTING FREQUENCY RESPONSE FOR
VARIOUS SIGNAL LEVELS
5
RF = 100
3
VS = ±2.55V
AV = -1
RF = 420
RL = 500
VIN = 280mVP-P
1
VIN = 20mVP-P
-1
-3
-5
100k
VIN = 1.4VP-P
VIN = 2.24VP-P
1M
10M
100M
1G
FREQUENCY (Hz)
FIGURE 14. INVERTING FREQUENCY RESPONSE FOR
VARIOUS INPUT SIGNAL LEVELS
FN7328.2
May 3, 2007
EL1516, EL1516A
Typical Performance Curves
3
5
VS = ±2.5V
AV = +2
RL = 500
1
RF = 348
-1
RF = 100
RF = 619
RL = 1k
-3
-5
100k
1M
10M
100M
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
5
(Continued)
VS = ±2.5V
RF = 348
RL = 500
3
1
AV = +2
-1
AV = +5
-3
AV = +10
-5
100k
1G
1M
FREQUENCY (Hz)
FIGURE 15. NON-INVERTING FREQUENCY RESPONSE FOR
VARIOUS RF
3
VS = ±2.5V
AV = +2
RF = 619
RL = 500
-1
CL = 27pF
CL = 18pF
CL = 3.3pF
CL = 0pF
-3
-5
100k
1M
10M
100M
VS = ±2.5V
AV = +2
3 RL = 619
1
RF = 100
-1
RF = 500
-3
RL = 50
-5
100k
1G
1M
FIGURE 17. NON-INVERTING FREQUENCY RESPONSE FOR
VARIOUS CL
-30
VS = ±2.55V
RF = 348
RL = 500
VIN = 20mVP-P
-1
-3
VIN = 200mVP-P
VIN = 500mVP-P
1M
10M
100M
1G
FREQUENCY (Hz)
FIGURE 19. NON-INVERTING FREQUENCY RESPONSE FOR
VARIOUS INPUT SIGNAL LEVELS
8
-50
-60
-70
2ND HD
-80
3RD HD
-90
VIN = 1VP-P
-5
100k
1G
VS = ±6V
RF = RG = 619
RL = 100
-40
VIN = 100mVP-P
1
100M
FIGURE 18. NON-INVERTING FREQUENCY RESPONSE FOR
VARIOUS RL
DISTORTION (dB)
NORMALIZED GAIN (dB)
3
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
5
1G
5
CL = 10pF
1
100M
FIGURE 16. NON-INVERTING FREQUENCY RESPONSE FOR
VARIOUS AV
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
5
10M
FREQUENCY (Hz)
-100
0
2
4
6
8
10
OUTPUT SWING (VPP)
FIGURE 20. 1MHz 2ND AND 3RD HARMONIC DISTORTION vs
OUTPUT SWING
FN7328.2
May 3, 2007
EL1516, EL1516A
Typical Performance Curves
-70
-20
-80
HARMONIC DISTORTION (dBc)
VO = 2VPP
VS = ±6V
RF = RG = 620
RL = 500
-75
THD + NOISE (dBc)
(Continued)
-85
-90
-95
-100
-105
10k
100k
VS = ±2.5V
AV = +2
RF = RG = 619
RL = 100
VOUT = 2VP-P
-30
-40
-50
-60
-70
THD
-80
2ND HD
-90
3RD HD
-100
500k
200k
FREQUENCY (Hz)
FIGURE 21. THD + NOISE vs FREQUENCY
-40
10
THD (dBc)
SUPPLY CURRENT (mA)
12
THD-FIN = 10MHz
-60
-70
-80
VS = ±2.5V
AV = +2
RF = RG = 619
RL = 500
THD-FIN = 1MHz
-90
-100
0.2
0.7
1.2
1.7
10M
2.7
2.2
8
6
4
2
0
3.2
0
1
2
OUTPUT VOLTAGE (VP-P)
3
5
4
6
SUPPLY VOLTAGE (±V)
FIGURE 23. THD vs OUTPUT VOLTAGE
FIGURE 24. SUPPLY CURRENT vs SUPPLY VOLTAGE
250
-10
VS = ±6V
AV = +2
-30 RF = 620
RL = 500
AV = +2
200
150
GAIN (dB)
3dB BANDWIDTH (MHz)
20M
FIGURE 22. HARMONIC DISTORTION vs FREQUENCY
-30
-50
1M
FUNDAMENTAL FREQUENCY (Hz)
AV = -1
100
AV = -2
AV = +5
50
AV = -5
AV = -10
2
4
3
5
6
SUPPLY VOLTAGE (±V)
FIGURE 25. 3dB BANDWIDTH vs SUPPLY VOLTAGE
9
BaaaA
-70
AaaaB
-90
AV = +10
0
-50
-110
100k
1M
10M
100M
1G
FREQUENCY (Hz)
FIGURE 26. CHANNEL-TO-CHANNEL ISOLATION vs
FREQUENCY
FN7328.2
May 3, 2007
EL1516, EL1516A
Typical Performance Curves
-30
(Continued)
-10
VS = ±6V
RL = 1k
-30
PSRR (dB)
CMRR (dB)
-50
-70
-90
-110
VS = ±6V
AV = +1
RL = 500
-50
PSRR+
-70
PSRR-
-90
-130
100k
1M
10M
100M
-110
100k
1G
1M
FIGURE 27. CMRR
1G
10k
100k
12
VOLTAGE NOISE (nV/Hz)
OUTPUT IMPEDANCE ()
100M
FIGURE 28. PSRR
100
10
1
-0.1
0.01
10k
100k
1M
10M
100M
10
8
6
4
2
0
10
FIGURE 29. CLOSED LOOP OUTPUT IMPEDANCE vs
FREQUENCY
0.07
VS = ±6V
AV = 2
RF = 620
0.06
100
1k
FREQUENCY (Hz)
FREQUENCY (Hz)
DIFF GAIN (%), DIFF PHASE (°)
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 30. VOLTAGE NOISE
VS = ±6V
RL = 500
RF = 620
DIFF GAIN
0.05
0.04
DIFF PHASE
0.5V/DIV
0.03
0.02
0.01
0
1
2
3
4
100ns/DIV
NUMBER OF 150 LOADS
FIGURE 31. DIFFERENTIAL GAIN/PHASE
10
FIGURE 32. LARGE SIGNAL STEP RESPONSE
FN7328.2
May 3, 2007
EL1516, EL1516A
Typical Performance Curves
(Continued)
VS = ±2.5V
RL = 500
RF = 620
0.5V/DIV
VS = ±6V
RL = 500
RF = 620
20mV/DIV
100ns/DIV
100ns/DIV
FIGURE 33. LARGE SIGNAL STEP RESPONSE
FIGURE 34. SMALL SIGNAL STEP RESPONSE
10
VS = ±2.5V
RL = 500
RF = 620
9
IS (mA)
8
20mV/DIV
7
6
5
4
3
2
-40 -20
100ns/DIV
0
20
40
60
80 100 120 140 150
DIE TEMPERATURE (°C)
FIGURE 35. SMALL SIGNAL STEP RESPONSE
FIGURE 36. SUPPLY CURRENT vs TEMPERATURE
200
450
160
SLEW RATE (±V/µs)
-3dB BANDWIDTH (MHz)
500
400
350
300
120
80
40
250
200
-40 -20
AV = +2V
VO = 2VP-P
RF = 200
RL = 500
0
20
40
60
80 100 120 140 150
DIE TEMPERATURE (°C)
FIGURE 37. -3dB BANDWIDTH vs TEMPERATURE
11
0
-40 -20
0
20
40
60
80 100 120 140 150
DIE TEMPERATURE (°C)
FIGURE 38. SLEW RATE vs TEMPERATURE
FN7328.2
May 3, 2007
EL1516, EL1516A
Typical Performance Curves
0
VS = ±6V
50mVOPP
-50
26
-100
22
VOS (µV)
SETTLING TIME (ns)
30
(Continued)
18
-150
-200
-250
-300
14
-350
10
-40 -20
0
20
40
60
-400
-40 -20
80 100 120 140 150
0
DIE TEMPERATURE (°C)
FIGURE 39. 0.1% SETTLING TIME vs TEMPERATURE
1.2
POWER DISSIPATION (W)
IBIAS (µA)
7
6
5
0
20
40
60
80 100 120 140 150
60
80 100 120 140 150
JEDEC JESD51-3 LOW EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
1
781mW
0.8
SO8
JA = 160°C/W
607mW
0.6
MSOP8/10
JA = 206°C/W
0.4
0.2
0
0
25
50
75 85 100
125
150
AMBIENT TEMPERATURE (°C)
DIE TEMPERATURE (°C)
FIGURE 41. IBIAS CURRENT vs TEMPERATURE
1.8
40
FIGURE 40. VOS vs TEMPERATURE
8
4
-40 -20
20
DIE TEMPERATURE (°C)
FIGURE 42. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
JEDEC JESD51-7 HIGH EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
POWER DISSIPATION (W)
1.6
1.4
1.2 1.136W
SO8
JA = 110°C/W
1 1.087W
0.8
MSOP8/10
JA = 115°C/W
0.6
0.4
0.2
0
0
25
50
75 85 100
125
150
AMBIENT TEMPERATURE (°C)
FIGURE 43. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
12
FN7328.2
May 3, 2007
EL1516, EL1516A
Pin Descriptions
EL1516
(8 Ld SOIC
AND
8 Ld MSOP)
EL1516A
(10 Ld MSOP)
PIN NAME
PIN FUNCTION
1
9
VOUTA
Output
EQUIVALENT CIRCUIT
VS+
VOUT
CIRCUIT 1
2
10
VINA-
Input
VS+
VIN+
VIN-
VSCIRCUIT 2
3
1
VINA+
Input
Reference Circuit 2
4
3
VS-
Supply
5
5
VINB+
Input
6
6
VINB-
Input
Reference Circuit 2
7
7
VOUTB
Output
Reference Circuit 1
8
8
VS+
Supply
2, 4
ENA, ENB
Enable
VS+
EN
570k
VSCIRCUIT 3
13
FN7328.2
May 3, 2007
EL1516, EL1516A
Applications Information
T JMAX = T MAX +   JA  PD MAXTOTAL 
Product Description
The EL1516 is a dual voltage feedback operational amplifier
designed especially for DMT ADSL and other applications
requiring very low voltage and current noise. It also features
low distortion while drawing moderately low supply current.
The EL1516 uses a classical voltage-feedback topology
which allows it to be used in a variety of applications where
current-feedback amplifiers are not appropriate because of
restrictions placed upon the feedback element used with the
amplifier. The conventional topology of the EL1516 allows,
for example, a capacitor to be placed in the feedback path,
making it an excellent choice for applications such as active
filters, sample-and-holds, or integrators.
ADSL CPE Applications
The low noise EL1516 amplifier is specifically designed for
the dual differential receiver amplifier function with ADSL
transceiver hybrids as well as other low-noise amplifier
applications. A typical ADSL CPE line interface circuit is
shown in Figure 44. The EL1516 is used in receiving DMT
down stream signal. With careful transceiver hybrid design
and the EL1516 1.4nV/Hz voltage noise and 1.5pA/Hz
current noise performance, -140dBm/Hz system background
noise performance can be easily achieved.
DRIVER
INPUT
+
-
ROUT
LINE +
RF
RG
ZLINE
RF
ROUT
+
RF
RECEIVE
OUT +
RECEIVE
OUT -
RECEIVE
AMPLIFIERS
+
+
RF
(EQ. 1)
where:
• PDMAXTOTAL is the sum of the maximum power
dissipation of each amplifier in the package (PDMAX)
• PDMAX for each amplifier can be calculated as follows:
V OUTMAX
PDMAX = 2  V S  I SMAX +  V S – V OUTMAX   ---------------------------RL
(EQ. 2)
where:
• TMAX = Maximum ambient temperature
• JA = Thermal resistance of the package
• PDMAX = Maximum power dissipation of 1 amplifier
• VS = Supply voltage
• IMAX = Maximum supply current of 1 amplifier
• VOUTMAX = Maximum output voltage swing of the
application
• RL = Load resistance
To serve as a guide for the user, we can calculate maximum
allowable supply voltages for the example of the video
cable-driver below since we know that TJMAX = +150°C,
TMAX = +75°C, ISMAX = 7.7mA, and the package JAs are
shown in Table 1. If we assume (for this example) that we
are driving a back-terminated video cable, then the
maximum average value (over duty-cycle) of VOUTMAX is
1.4V, and RL = 150, giving the results seen in Table 1.
TABLE 1.
LINE -
R
RIN
R
PART
PACKAGE
JA
MAX PDISS @
TMAX
EL1516IS
SO8
110°C/W 0.406W @ +85°C
EL1516IY
MSOP8
115°C/W 0.400W @ +85°C
EL1516AIY MSOP10
MAX VS
115°C/W 0.400W @ +85°C
RIN
Single-Supply Operation
FIGURE 44. TYPICAL LINE INTERFACE CONNECTION
Power Dissipation
With the wide power supply range and large output drive
capability of the EL1516, it is possible to exceed the +150°C
maximum junction temperatures under certain load and
power supply conditions. It is therefore important to calculate
the maximum junction temperature (TJMAX) for all
applications to determine if power supply voltages, load
conditions, or package type need to be modified for the
EL1516 to remain in the safe operating area. These
parameters are related as follows:
14
The EL1516 has been designed to have a wide input and
output voltage range. This design also makes the EL1516 an
excellent choice for single-supply operation. Using a single
positive supply, the lower input voltage range is within 1.2V
of ground (RL = 500), and the lower output voltage range is
within 875mV of ground. Upper input voltage range reaches
3.6V, and output voltage range reaches 3.8V with a 5V
supply and RL = 500. This results in a 2.625V output swing
on a single 5V supply. This wide output voltage range also
allows single-supply operation with a supply voltage as high
as 12V.
FN7328.2
May 3, 2007
EL1516, EL1516A
Gain-Bandwidth Product and the -3dB Bandwidth
Printed-Circuit Layout
The EL1516 has a gain-bandwidth product of 300MHz while
using only 6mA of supply current per amplifier. For gains
greater than 2, their closed-loop -3dB bandwidth is
approximately equal to the gain-bandwidth product divided
by the noise gain of the circuit. For gains less than 2, higherorder poles in the amplifiers' transfer function contribute to
even higher closed loop bandwidths. For example, the
EL1516 has a -3dB bandwidth of 350MHz at a gain of +2,
dropping to 80MHz at a gain of +5. It is important to note that
the EL1516 has been designed so that this “extra” bandwidth
in low-gain applications does not come at the expense of
stability. As seen in the typical performance curves, the
EL1516 in a gain of +2 only exhibits 0.5dB of peaking with a
1000 load.
The EL1516 is well behaved, and easy to apply in most
applications. However, a few simple techniques will help
assure rapid, high quality results. As with any high-frequency
device, good PCB layout is necessary for optimum
performance. Ground-plane construction is highly
recommended, as is good power supply bypassing. A 0.1µF
ceramic capacitor is recommended for bypassing both
supplies. Lead lengths should be as short as possible, and
bypass capacitors should be as close to the device pins as
possible. For good AC performance, parasitic capacitances
should be kept to a minimum at both inputs and at the
output. Resistor values should be kept under 5k because
of the RC time constants associated with the parasitic
capacitance. Metal-film and carbon resistors are both
acceptable, use of wire-wound resistors is not recommended
because of their parasitic inductance. Similarly, capacitors
should be low-inductance for best performance.
Output Drive Capability
The EL1516 has been designed to drive low impedance
loads. It can easily drive 6VPP into a 100 load. This high
output drive capability makes the EL1516 an ideal choice for
RF, IF and video applications.
15
FN7328.2
May 3, 2007
EL1516, EL1516A
Small Outline Package Family (SO)
A
D
h X 45°
(N/2)+1
N
A
PIN #1
I.D. MARK
E1
E
c
SEE DETAIL “X”
1
(N/2)
B
L1
0.010 M C A B
e
H
C
A2
GAUGE
PLANE
SEATING
PLANE
A1
0.004 C
0.010 M C A B
L
b
0.010
4° ±4°
DETAIL X
MDP0027
SMALL OUTLINE PACKAGE FAMILY (SO)
INCHES
SYMBOL
SO-14
SO16 (0.300”)
(SOL-16)
SO20
(SOL-20)
SO24
(SOL-24)
SO28
(SOL-28)
TOLERANCE
NOTES
A
0.068
0.068
0.068
0.104
0.104
0.104
0.104
MAX
-
A1
0.006
0.006
0.006
0.007
0.007
0.007
0.007
0.003
-
A2
0.057
0.057
0.057
0.092
0.092
0.092
0.092
0.002
-
b
0.017
0.017
0.017
0.017
0.017
0.017
0.017
0.003
-
c
0.009
0.009
0.009
0.011
0.011
0.011
0.011
0.001
-
D
0.193
0.341
0.390
0.406
0.504
0.606
0.704
0.004
1, 3
E
0.236
0.236
0.236
0.406
0.406
0.406
0.406
0.008
-
E1
0.154
0.154
0.154
0.295
0.295
0.295
0.295
0.004
2, 3
e
0.050
0.050
0.050
0.050
0.050
0.050
0.050
Basic
-
L
0.025
0.025
0.025
0.030
0.030
0.030
0.030
0.009
-
L1
0.041
0.041
0.041
0.056
0.056
0.056
0.056
Basic
-
h
0.013
0.013
0.013
0.020
0.020
0.020
0.020
Reference
-
16
20
24
28
Reference
-
N
SO-8
SO16
(0.150”)
8
14
16
Rev. M 2/07
NOTES:
1. Plastic or metal protrusions of 0.006” maximum per side are not included.
2. Plastic interlead protrusions of 0.010” maximum per side are not included.
3. Dimensions “D” and “E1” are measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994
16
FN7328.2
May 3, 2007
EL1516, EL1516A
Mini SO Package Family (MSOP)
0.25 M C A B
D
MINI SO PACKAGE FAMILY
(N/2)+1
N
E
MDP0043
A
E1
MILLIMETERS
PIN #1
I.D.
1
B
(N/2)
e
H
C
SEATING
PLANE
0.10 C
N LEADS
0.08 M C A B
b
SYMBOL
MSOP8
MSOP10
TOLERANCE
NOTES
A
1.10
1.10
Max.
-
A1
0.10
0.10
±0.05
-
A2
0.86
0.86
±0.09
-
b
0.33
0.23
+0.07/-0.08
-
c
0.18
0.18
±0.05
-
D
3.00
3.00
±0.10
1, 3
E
4.90
4.90
±0.15
-
E1
3.00
3.00
±0.10
2, 3
e
0.65
0.50
Basic
-
L
0.55
0.55
±0.15
-
L1
0.95
0.95
Basic
-
N
8
10
Reference
Rev. D 2/07
NOTES:
1. Plastic or metal protrusions of 0.15mm maximum per side are not
included.
L1
2. Plastic interlead protrusions of 0.25mm maximum per side are
not included.
A
3. Dimensions “D” and “E1” are measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994.
c
SEE DETAIL "X"
A2
GAUGE
PLANE
L
A1
0.25
3° ±3°
DETAIL X
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be
accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
17
FN7328.2
May 3, 2007