Si8817DB Datasheet

Si8817DB
www.vishay.com
Vishay Siliconix
P-Channel 20 V (D-S) MOSFET
FEATURES
PRODUCT SUMMARY
VDS (V)
-20
RDS(on) (Ω) MAX.
ID (A) a, e
0.076 at VGS = -4.5 V
-2.9
0.100 at VGS = -2.5 V
-2.5
0.145 at VGS = -1.8 V
-2.1
0.320 at VGS = -1.5 V
-0.5
MICRO FOOT® 0.8 x 0.8
S
3
xxx
xx
• TrenchFET® power MOSFET
• Small 0.8 mm x 0.8 mm outline area
• Low 0.4 mm max. profile
7.5 nC
• Material categorization:
for definitions of compliance please see
www.vishay.com/doc?99912
APPLICATIONS
S
• Load switches and chargers switches
S
2
• Battery management
G
• DC/DC converters
• For smart phones and tablet PCs
8
0.
m
m
1
Qg (Typ.)
0.8
mm
Backside View
1
G
4
D
Bump Side View
D
P-Channel MOSFET
Marking Code: xx = AF
xxx = Date/Lot traceability code
Ordering Information:
Si8817DB-T2-E1 (lead (Pb)-free and halogen-free)
ABSOLUTE MAXIMUM RATINGS (TA = 25 °C, unless otherwise noted)
PARAMETER
SYMBOL
LIMIT
Drain-Source Voltage
VDS
-20
Gate-Source Voltage
VGS
±8
TA = 70 °C
TA = 25 °C
ID
Continuous Source-Drain Diode Current
IDM
TC = 25 °C
TA = 25 °C
IS
TA = 70 °C
TA = 25 °C
PD
Package Reflow Conditions c
A
-15
-0.7 a
-0.4 b
0.6 a
0.5 b
W
0.3 b
TA = 70 °C
Operating Junction and Storage Temperature Range
-2.1 b
0.9 a
TA = 25 °C
Maximum Power Dissipation
-2.3 a
-1.7 b
TA = 70 °C
Pulsed Drain Current (t = 300 μs)
V
-2.9 a
TA = 25 °C
Continuous Drain Current (TJ = 150 °C)
UNIT
TJ, Tstg
-55 to 150
VPR
260
IR/Convection
260
°C
Notes
a. Surface mounted on 1" x 1" FR4 board with full copper, t = 5 s.
b. Surface mounted on 1" x 1" FR4 board with minimum copper, t = 5 s.
c. Refer to IPC/JEDEC® (J-STD-020), no manual or hand soldering.
d. In this document, any reference to case represents the body of the MICRO FOOT device and foot is the bump.
e. Based on TA = 25 °C.
S15-0346-Rev. B, 23-Feb-15
Document Number: 62759
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Si8817DB
www.vishay.com
Vishay Siliconix
THERMAL RESISTANCE RATINGS
PARAMETER
SYMBOL
Maximum Junction-to-Ambient a, b
t=5s
Maximum Junction-to-Ambient c, d
t=5s
RthJA
TYPICAL
MAXIMUM
105
135
200
260
UNIT
°C/W
Notes
a. Surface mounted on 1" x 1" FR4 board with full copper.
b. Maximum under steady state conditions is 185 °C/W.
c. Surface mounted on 1" x 1" FR4 board with minimum copper.
d. Maximum under steady state conditions is 330 °C/W.
SPECIFICATIONS (TJ = 25 °C, unless otherwise noted)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN.
TYP.
MAX.
UNIT
VDS
VGS = 0 V, ID = -250 μA
-20
-
-
V
-
-12
-
-
2.5
-
Static
Drain-Source Breakdown Voltage
VDS Temperature Coefficient
ΔVDS/TJ
VGS(th) Temperature Coefficient
ΔVGS(th)/TJ
Gate-Source Threshold Voltage
ID = -250 μA
mV/°C
VGS(th)
VDS = VGS, ID = -250 μA
-0.4
-
-1
V
Gate-Source Leakage
IGSS
VDS = 0 V, VGS = ± 8 V
-
-
± 100
nA
Zero Gate Voltage Drain Current
IDSS
On-State Drain Current a
ID(on)
Drain-Source On-State Resistance a
Forward Transconductance a
Dynamic
RDS(on)
gfs
VDS = -20 V, VGS = 0 V
-
-
-1
VDS = -20 V, VGS = 0 V, TJ = 70 °C
-
-
-10
VDS ≤ -5 V, VGS = -4.5 V
-5
-
-
VGS = -4.5 V, ID = -1 A
-
0.061
0.076
VGS = -2.5 V, ID = -1 A
-
0.080
0.100
VGS = -1.8 V, ID = -0.5 A
-
0.110
0.145
VGS = -1.5 V, ID = -0.5 A
-
0.165
0.320
VDS = -10 V, ID = -1 A
-
5
-
-
615
-
VDS = -10 V, VGS = 0 V, f = 1 MHz
-
90
-
-
75
-
μA
A
Ω
S
b
Input Capacitance
Ciss
Output Capacitance
Coss
Reverse Transfer Capacitance
Crss
Total Gate Charge
Qg
Gate-Source Charge
Qgs
Gate-Drain Charge
Qgd
Gate Resistance
Turn-On Delay Time
Rise Time
Turn-Off Delay Time
Fall Time
Turn-On Delay Time
Rise Time
Turn-Off Delay Time
Fall Time
S15-0346-Rev. B, 23-Feb-15
Rg
VDS = -10 V, VGS = -8 V, ID = -1 A
VDS = -10 V, VGS = -4.5 V, ID = -1 A
VGS = -0.1 V, f = 1 MHz
td(on)
tr
VDD = -10 V, RL = 10 Ω
ID ≅ -1 A, VGEN = -4.5 V, Rg = 1 Ω
-
12.5
19
-
7.5
12
-
1
-
-
1.9
-
-
14
-
-
20
40
-
20
40
-
52
100
tf
-
22
45
td(on)
-
6
15
td(off)
tr
td(off)
tf
VDD = -10 V, RL = 10 Ω
ID ≅ -1 A, VGEN = -8 V, Rg = 1 Ω
-
10
20
-
60
120
-
23
45
pF
nC
Ω
ns
Document Number: 62759
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Si8817DB
www.vishay.com
Vishay Siliconix
SPECIFICATIONS (TJ = 25 °C, unless otherwise noted)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN.
TYP.
MAX.
UNIT
TA = 25 °C
-
-
-0.7
-
-
-15
-
-0.75
-1.2
V
-
30
60
ns
-
14
30
nC
-
13
-
-
17
-
Drain-Source Body Diode Characteristics
Continuous Source-Drain Diode
Current
IS
Pulse Diode Forward Current
ISM
Body Diode Voltage
VSD
Body Diode Reverse Recovery Time
trr
Body Diode Reverse Recovery Charge
Qrr
Reverse Recovery Fall Time
ta
Reverse Recovery Rise Time
tb
IS = -1 A, VGS = 0 V
IF = -1 A, dI/dt = 100 A/μs, TJ = 25 °C
A
ns
Notes
a. Pulse test; pulse width ≤ 300 μs, duty cycle ≤ 2 %
b. Guaranteed by design, not subject to production testing.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
S15-0346-Rev. B, 23-Feb-15
Document Number: 62759
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Si8817DB
www.vishay.com
Vishay Siliconix
TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted)
10
15
VGS = 5 V thru 3 V
VGS = 2.5 V
8
9
ID - Drain Current (A)
ID - Drain Current (A)
12
VGS = 2 V
6
3
6
TC = 25 °C
4
TC = 125 °C
2
VGS = 1.5 V
TC = - 55 °C
0
0
0.0
0.5
1.0
1.5
2.0
2.5
VDS - Drain-to-Source Voltage (V)
0.0
3.0
0.5
1.0
1.5
2.0
VGS - Gate-to-Source Voltage (V)
Output Characteristics
2.5
Transfer Characteristics
0.40
1000
800
0.30
C - Capacitance (pF)
RDS(on) - On-Resistance (Ω)
VGS = 1.5 V
VGS = 1.8 V
0.20
VGS = 2.5 V
0.10
Ciss
600
400
200
Coss
Crss
VGS = 4.5 V
0.00
0
0
3
6
9
ID - Drain Current (A)
12
15
0
4
On-Resistance vs. Drain Current and Gate Voltage
12
16
20
Capacitance
1.4
8
ID = 1 A
RDS(on) - On-Resistance (Normalized)
ID = 1 A
VGS - Gate-to-Source Voltage (V)
8
VDS - Drain-to-Source Voltage (V)
VDS = 10 V
6
VDS = 5 V
VDS = 16 V
4
2
0
0
3
6
9
12
Qg - Total Gate Charge (nC)
Gate Charge
S15-0346-Rev. B, 23-Feb-15
15
1.3
VGS = 4.5 V, 2.5 V
1.2
VGS = 1.8 V
1.1
VGS = 1.5 V
1.0
0.9
0.8
- 50
- 25
0
25
50
75
100
TJ - Junction Temperature (°C)
125
150
On-Resistance vs. Junction Temperature
Document Number: 62759
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Si8817DB
www.vishay.com
Vishay Siliconix
TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted)
100
0.40
ID = 1 A
RDS(on) - On-Resistance (Ω)
IS - Source Current (A)
0.32
TJ = 150 °C
10
TJ = 25 °C
1
0.24
0.16
TJ = 125 °C
0.08
TJ = 25 °C
0.1
0.00
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
VSD - Source-to-Drain Voltage (V)
0
1
2
3
4
VGS - Gate-to-Source Voltage (V)
5
Source-Drain Diode Forward Voltage
On-Resistance vs. Gate-to-Source Voltage
14
0.9
12
0.8
10
Power (W)
VGS(th) (V)
0.7
0.6
8
6
ID = 250 μA
0.5
4
0.4
0.3
- 50
2
- 25
0
25
50
75
100
125
0
0.001
150
TJ - Temperature (°C)
0.01
0.1
1
Time (s)
10
100
Threshold Voltage
Single Pulse Power, Junction-to-Ambient
1000
100
Limited by RDS(on)*
ID - Drain Current (A)
10
100 μs
1
1 ms
10 ms
0.1
TA = 25 °C
100 ms
1 s, 10 s
DC
BVDSS Limited
0.01
0.1
1
10
100
VDS - Drain-to-Source Voltage (V)
* VGS > minimum VGS at which RDS(on) is specified
Safe Operating Area, Junction-to-Ambient
S15-0346-Rev. B, 23-Feb-15
Document Number: 62759
5
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Si8817DB
www.vishay.com
Vishay Siliconix
TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted)
3.0
0.8
Power Dissipation (W)
ID - Drain Current (A)
2.5
2.0
1.5
1.0
0.6
0.4
0.2
0.5
0.0
0.0
0
25
50
75
100
TC - Case Temperature (°C)
Current Derating*
125
150
25
50
75
100
125
T A - Ambient Temperature (°C)
150
Power Derating
Note
When mounted on 1" x 1" FR4 with full copper.
* The power dissipation PD is based on TJ (max.) = 150 °C, using junction-to-case thermal resistance, and is more useful in settling
the upper dissipation limit for cases where additional heatsinking is used. It is used to determine the current rating, when this
rating falls below the package limit.
S15-0346-Rev. B, 23-Feb-15
Document Number: 62759
6
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Si8817DB
www.vishay.com
Vishay Siliconix
TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted)
1
Normalized Effective Transient
Thermal Impedance
Duty Cycle = 0.5
0.2
0.1
Notes:
0.05
PDM
0.1
t1
0.02
t2
1. Duty Cycle, D =
t1
t2
2. Per Unit Base = R thJA = 185 °C/W
3. T JM - T A = PDMZthJA(t)
4. Surface Mounted
Single Pulse
0.01
0.0001
0.001
0.01
0.1
1
100
10
1000
Square Wave Pulse Duration (s)
Normalized Thermal Transient Impedance, Junction-to-Ambient (On 1" x 1" FR4 Board with Maximum Copper)
1
Normalized Effective Transient
Thermal Impedance
Duty Cycle = 0.5
0.2
0.1
Notes:
0.05
PDM
0.1
t1
t2
1. Duty Cycle, D =
0.02
t1
t2
2. Per Unit Base = R thJA = 330 °C/W
3. T JM - TA = PDMZthJA(t)
Single Pulse
0.01
0.0001
0.001
4. Surface Mounted
0.01
0.1
1
10
100
1000
Square Wave Pulse Duration (s)
Normalized Thermal Transient Impedance, Junction-to-Ambient (On 1" x 1" FR4 Board with Minimum Copper)
Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon
Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and
reliability data, see www.vishay.com/ppg?62759.
S15-0346-Rev. B, 23-Feb-15
Document Number: 62759
7
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Package Information
www.vishay.com
Vishay Siliconix
MICRO FOOT®: 4-Bump (0.8 mm x 0.8 mm, 0.4 mm Pitch)
D
S
e
S
e
XXX
S
D
S
S
4x Ø b
G
D
S
AK
Mark on Backside of die
A2
4-Ø 0.205 to 0.225 Note 5
Solder Mask ~Ø 0.215
A1
A
e
b
k
b1
e
Bump Note 2
Note 4
Notes
(1) Laser mark on the backside surface of die
(2) Bumps are 95.5 % Sn,3.8 % Ag,0.7 % Cu
(3) “i” is the location of pin 1
(4) “b1” is the diameter of the solderable substrate surface, defined by an opening in the solder resist layer solder mask defined.
(5) Non-solder mask defined copper landing pad.
DIM.
MILLIMETERS a
INCHES
MIN.
NOM.
MAX.
MIN.
NOM.
MAX.
A
0.328
0.365
0.402
0.0129
0.0144
0.0158
A1
0.136
0.160
0.184
0.0053
0.0062
0.0072
A2
0.192
0.205
0.218
0.0076
0.0081
0.0086
b
0.200
0.220
0.240
0.0078
0.0086
0.0094
b1
0.175
0.0068
e
0.400
0.0157
S
0.160
0.180
0.200
0.0062
0.0070
0.0078
D
0.720
0.760
0.800
0.0283
0.0299
0.0314
K
0.040
0.070
0.100
0.0015
0.0027
0.0039
Note
a. Use millimeters as the primary measurement.
ECN: T15-0053-Rev. A, 16-Feb-15
DWG: 6033
Revision: 16-Feb-15
1
Document Number: 69442
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000