Si8466EDB www.vishay.com Vishay Siliconix N-Channel 8 V (D-S) MOSFET FEATURES PRODUCT SUMMARY VDS (V) 8 RDS(on) (Ω) MAX. ID (A) a, e 0.043 at VGS = 4.5 V 5.4 0.046 at VGS = 2.5 V 5.2 0.060 at VGS = 1.5 V 4.6 0.090 at VGS = 1.2 V 3.0 MICRO FOOT® 1 x xxx xx x Qg (TYP.) m m m 1m Backside View 1 • Typical ESD protection 3000 V HBM • Ultra-Small 1 mm x 1 mm maximum outline 6.8 nC • Ultra-thin 0.548 mm maximum height • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 1x1 S 3 • TrenchFET® power MOSFET S 2 APPLICATIONS D • Low on-resistance load switch for portable devices 1 G 4 D Bump Side View - Low power consumption, low voltage drop G - Increased battery life Marking Code: xxxx = 8466 xxx = Date / lot traceability code - Space savings on PCB Ordering Information: Si8466DB-T2-E1 (lead (Pb)-free and halogen-free) N-Channel MOSFET S ABSOLUTE MAXIMUM RATINGS (TA = 25 °C, unless otherwise noted) PARAMETER SYMBOL LIMIT Drain-Source Voltage VDS 8 Gate-Source Voltage VGS ±5 TA = 70 °C TA = 25 °C 4.4 a ID 3.6 b 2.9 b TA = 70 °C Pulsed Drain Current (t = 300 μs) Continuous Source-Drain Diode Current IDM TC = 25 °C TA = 25 °C TA = 70 °C TA = 25 °C 1.5 a IS 0.65 b 1.8 a 1.1 a PD Package Reflow Conditions c W 0.78 b 0.5 b TA = 70 °C Operating Junction and Storage Temperature Range A 20 TA = 25 °C Maximum Power Dissipation V 5.4 a TA = 25 °C Continuous Drain Current (TJ = 150 °C) UNIT TJ, Tstg -55 to +150 VPR 260 IR/Convection 260 °C THERMAL RESISTANCE RATINGS PARAMETER SYMBOL Maximum Junction-to-Ambient f, g t = 10 s Maximum Junction-to-Ambient h, i t = 10 s RthJA TYPICAL MAXIMUM 55 70 125 160 UNIT °C/W Notes a. Surface mounted on 1" x 1" FR4 board with full copper, t = 10 s. b. Surface mounted on 1" x 1" FR4 board with minimum copper, t = 10 s. c. Refer to IPC/JEDEC® (J-STD-020), no manual or hand soldering. d. In this document, any reference to case represents the body of the MICRO FOOT device and foot is the bump. e. Based on TA = 25 °C. f. Surface mounted on 1" x 1" FR4 board with full copper. g. Maximum under steady state conditions is 100 °C/W. h. Surface mounted on 1" x 1" FR4 board with minimum copper. i. Maximum under steady state conditions is 190 °C/W. S15-1510-Rev. B, 29-Jun-15 Document Number: 63683 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Si8466EDB www.vishay.com Vishay Siliconix SPECIFICATIONS (TJ = 25 °C, unless otherwise noted) PARAMETER SYMBOL TEST CONDITIONS MIN. TYP. MAX. UNIT VDS VGS = 0 V, ID = 250 μA 8 - - V - 3.5 - - -3 - Static Drain-Source Breakdown Voltage VDS Temperature Coefficient ΔVDS/TJ VGS(th) Temperature Coefficient ΔVGS(th)/TJ Gate-Source Threshold Voltage ID = 250 μA mV/°C VGS(th) VDS = VGS, ID = 250 μA 0.35 - 0.7 V Gate-Source Leakage IGSS VDS = 0 V, VGS = ± 5 V - - ±3 μA Zero Gate Voltage Drain Current IDSS On-State Drain Current a ID(on) Drain-Source On-State Resistance a VDS = 8 V, VGS = 0 V - - 1 VDS = 8 V, VGS = 0 V, TJ = 70 °C - - 10 VDS ≥ 5 V, VGS = 4.5 V 10 - - VGS = 4.5 V, ID = 2 A - 0.035 0.043 VGS = 2.5 V, ID = 1 A - 0.037 0.046 VGS = 1.5 V, ID = 1 A - 0.045 0.060 VGS = 1.2 V, ID = 0.5 A - 0.055 0.090 VDS = 4 V, ID = 2 A - 30 - - 710 - VDS = 4 V, VGS = 0 V, f = 1 MHz - 270 - RDS(on) Forward Transconductance a gfs μA A Ω S Dynamic b Input Capacitance Ciss Output Capacitance Coss Reverse Transfer Capacitance Crss - 192 - Total Gate Charge Qg - 8.5 13 - 0.9 - - 1.6 - Gate-Source Charge Qgs Gate-Drain Charge Qgd Gate Resistance Turn-On Delay Time Rg VGS = 0.1 V, f = 1 MHz td(on) Rise Time Turn-Off Delay Time VDS = 4 V, VGS = 4.5 V, ID = 2 A tr td(off) Fall Time VDD = 4 V, RL = 2 Ω ID ≅ 2 A, VGEN = 4.5 V, Rg = 1 Ω tf pF nC Ω - 6 - - 10 20 - 15 30 - 40 80 - 10 20 - - 1.5 - - 20 - 0.7 1.2 V - 30 60 ns - 7 15 nC - 15 - - 15 - ns Drain-Source Body Diode Characteristics Continuous Source-Drain Diode Current IS Pulse Diode Forward Current ISM Body Diode Voltage VSD Body Diode Reverse Recovery Time trr Body Diode Reverse Recovery Charge Qrr Reverse Recovery Fall Time ta Reverse Recovery Rise Time tb TA = 25 °C IS = 1.5 A, VGS = 0 IF = 2 A, dI/dt = 100 A/μs, TJ = 25 °C A ns Notes a. Pulse test; pulse width ≤ 300 μs, duty cycle ≤ 2 %. b. Guaranteed by design, not subject to production testing. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. S15-1510-Rev. B, 29-Jun-15 Document Number: 63683 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Si8466EDB www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted) 10-1 20 10-2 10-3 12 IGSS - Gate Current (A) IGSS - Gate Current (mA) 16 TJ = 25 °C 8 TJ = 150 °C 10-4 10-5 TJ = 25 °C 10-6 10-7 4 10-8 10-9 0 0 3 6 9 12 15 VGS - Gate-Source Voltage (V) 6 9 12 VGS - Gate-to-Source Voltage (V) Output Characteristics On-Resistance vs. Drain Current and Gate Voltage S15-1510-Rev. B, 29-Jun-15 0 3 15 Document Number: 63683 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Si8466EDB www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted) 20 20 VGS = 5 V thru 1.5 V 16 ID - Drain Current (A) ID - Drain Current (A) 16 12 8 4 12 TC = 25 °C 8 TC = 125 °C 4 VGS = 1 V TC = - 55 °C 0 0 0.0 0.5 1.0 1.5 2.0 0.0 0.4 0.8 1.2 1.6 VGS - Gate-to-Source Voltage (V) VDS - Drain-to-Source Voltage (V) Output Characteristics 2.0 Transfer Characteristics 1200 0.120 VGS = 1.2 V 1000 Ciss C - Capacitance (pF) RDS(on) - On-Resistance (Ω) 0.100 0.080 0.060 VGS = 2.5 V VGS = 1.5 V 0.040 0.020 0.000 0 800 600 Coss 400 Crss VGS = 4.5 V 200 0 4 8 12 ID - Drain Current (A) 16 0 20 2 4 6 VDS - Drain-to-Source Voltage (V) On-Resistance vs. Drain Current and Gate Voltage Capacitance 1.4 ID = 2 A 4 RDS(on) - On-Resistance (Normalized) 5 VGS - Gate-to-Source Voltage (V) 8 VDS = 4 V 3 VDS = 2 V 2 VDS = 6.4 V 1 0 0 2 4 6 8 Qg - Total Gate Charge (nC) Gate Charge S15-1510-Rev. B, 29-Jun-15 10 VGS = 4.5 V, 2.5 V, 1.5 V, I D = 2 A 1.3 1.2 1.1 VGS = 1.2 V, ID = 0.5 A 1.0 0.9 0.8 - 50 - 25 0 25 50 75 100 TJ - Junction Temperature (°C) 125 150 On-Resistance vs. Junction Temperature Document Number: 63683 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Si8466EDB www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted) 100 0.120 RDS(on) - On-Resistance (Ω) IS - Source Current (A) 0.100 TJ = 150 °C 10 TJ = 25 °C 1 ID = 2 A 0.080 0.060 TJ = 125 °C 0.040 TJ = 25 °C 0.020 0.000 0.1 0.0 VSD - Source-to-Drain Voltage (V) 2 3 4 VGS - Gate-to-Source Voltage (V) Source-Drain Diode Forward Voltage On-Resistance vs. Gate-to-Source Voltage 0.2 0.4 0.6 0.8 1.0 0.8 25 0.7 20 Power (W) 0.6 VGS(th) (V) 0 1.2 0.5 ID = 250 μA 1 5 15 10 0.4 5 0.3 0.2 - 50 - 25 0 25 50 75 100 TJ - Temperature (°C) 125 150 0 0.001 0.01 0.1 1 10 100 1000 Time (s) Threshold Voltage Single Pulse Power, Junction-to-Ambient 100 Limited by RDS(on)* 100 µs ID - Drain Current (A) 10 1 ms 1 10 ms 100 ms 10 s, 1s DC 0.1 TA = 25 °C BVDSS Limited 0.01 0.1 1 10 100 VDS - Drain-to-Source Voltage (V) * VGS > minimum VGS at which RDS(on) is specified Safe Operating Area, Junction-to-Ambient S15-1510-Rev. B, 29-Jun-15 Document Number: 63683 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Si8466EDB www.vishay.com Vishay Siliconix 5 1.5 4 1.2 Power Dissipation (W) ID - Drain Current (A) TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted) 3 2 0.9 0.6 0.3 1 0.0 0 0 25 50 75 100 125 TA - Ambient Temperature (°C) Current Derating a 150 25 50 75 100 125 150 TA - Ambient Temperature (°C) Power Derating Note • When mounted on 1" x 1" FR4 with full copper. Note a. The power dissipation PD is based on TJ (max.) = 150 °C, using junction-to-case thermal resistance, and is more useful in settling the upper dissipation limit for cases where additional heatsinking is used. It is used to determine the current rating, when this rating falls below the package limit. S15-1510-Rev. B, 29-Jun-15 Document Number: 63683 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Si8466EDB www.vishay.com Vishay Siliconix TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted) 1 Normalized Effective Transient Thermal Impedance Duty Cycle = 0.5 0.2 0.1 Notes: 0.1 0.05 PDM 0.02 t1 t2 1. Duty Cycle, D = t1 t2 2. Per Unit Base = RthJA = 100 °C/W 3. TJM - TA = PDMZthJA(t) Single Pulse 4. Surface Mounted 0.01 10 -4 10 -3 10 -2 10 -1 1 100 10 1000 Square Wave Pulse Duration (s) Normalized Thermal Transient Impedance, Junction-to-Ambient (1" x 1" FR4 Board with Full Copper) 1 Normalized Effective Transient Thermal Impedance Duty Cycle = 0.5 0.2 Notes: 0.1 0.1 PDM 0.05 t1 t2 1. Duty Cycle, D = t1 t2 2. Per Unit Base = RthJA = 190 °C/W 0.02 3. TJM - TA = PDMZthJA(t) Single Pulse 4. Surface Mounted 0.01 10 -4 10 -3 10 -2 10 -1 1 Square Wave Pulse Duration (s) 10 100 1000 Normalized Thermal Transient Impedance, Junction-to-Ambient (1" x 1" FR4 Board with Minimum Copper) Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see www.vishay.com/ppg?63683. S15-1510-Rev. B, 29-Jun-15 Document Number: 63683 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Package Information www.vishay.com Vishay Siliconix MICRO FOOT®: 4-Bumps (1 mm x 1 mm, 0.5 mm Pitch, 0.286 mm Bump Height) 4x Ø b1 S D G 4x 0.30 to 0.31 (Note 3) Solder mask-0.4 s e e XXXX XXX S D Mark on backside of die s e e D Recommended land pattern A2 b A1 A b1 Note 5 K Bump (Note 1) Notes 1. Bumps are 95.5/3.8/0.7 Sn/Ag/Cu. 2. Backside surface is coated with a Ti/Ni/Ag layer. 3. Non-solder mask defined copper landing pad. 4. Laser mark on the backside surface of die. 5. “b1” is the diameter of the solderable substrate surface, defined by an opening in the solder resist layer solder mask defined. 6. • is the location of pin 1 DIM. MILLIMETERS INCHES MIN. NOM. MAX. MIN. NOM. MAX. A 0.458 0.504 0.550 0.0180 0.0198 0.0217 A1 0.214 0.250 0.286 0.0084 0.0098 0.0113 A2 0.244 0.254 0.264 0.0096 0.0100 0.0104 b 0.297 0.330 0.363 0.0117 0.0130 0.0143 b1 0.250 e 0.500 0.0098 0.0197 s 0.210 0.230 0.250 0.0083 0.0091 0.0096 D 0.920 0.960 1.000 0.0362 0.0378 0.0394 K 0.029 0.065 0.102 0.0011 0.0026 0.0040 Note • Use millimeters as the primary measurement. ECN: T15-0176-Rev. A, 27-Apr-15 DWG: 6039 Revision: 27-Apr-15 1 Document Number: 69370 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000