SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) SIDACtor® Series - DO-15 Description The SIDACtor Series DO-15 are designed to protect baseband equipment such as modems, line cards, CPE and DSL from damaging overvoltage transients. The series provides a cost-effective through-hole solution that enables equipment to comply with global regulatory standards. Features and Benefits t Low voltage overshoot t Fails short circuit when surged in excess of ratings t Low on-state voltage Agency Approvals Agency t Does not degrade with use t Low Capacitance Agency File Number E133083 Applicable Global Standards Pinout Designation Not Applicable Schematic Symbol t TIA-968-A t GR 1089 Intra-building t TIA-968-B t IEC 61000-4-5 t ITU K.20/21 Enhanced Level* t YD/T 1082 t ITU K.20/21 Basic Level t YD/T 950 t YD/T 993 t GR 1089 Inter-building* * A/B-rated parts require series resistance Electrical Characteristics Part Number P1100GALRP P1300GALRP P1500GALRP P1800GALRP P2300GALRP P2600GALRP P3100GALRP P3500GALRP P1100GBLRP P1300GBLRP P1500GBLRP P1800GBLRP P2300GBLRP P2600GBLRP P3100GBLRP P3500GBLRP Marking VDRM @lDRM=5μA VS @100V/μs P11A P13A P15A P18A P23A P26A P31A P35A P11B P13B P15B P18B P23B P26B P31B P35B V min 90 120 140 170 190 220 275 320 90 120 140 170 190 220 275 320 V max 130 160 180 220 260 300 350 400 130 160 180 220 260 300 350 400 IH mA min mA max 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 150 800 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional. © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. IS 163 Revised: February 22, 2011 IT VT @IT=2.2 Amps A max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 V max 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 Capacitance @1MHz, 2V bias pF min 30 25 25 25 25 25 20 20 30 25 25 25 25 25 20 20 pF max 60 40 40 40 30 30 30 30 60 40 40 40 30 30 30 30 SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Surge Ratings ITSM IPP 10x560 10x560 2 10x1000 10x1000 2 50 / 60 Hz Amps min Amps min Amps min A 50 45 20 B 100 80 25 1 Series 1 Notes: 1 Current waveform in μs 2 Voltage waveform in μs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPGUP$ - The device must initially be in thermal equilibrium with -40°C < TJ <¡$ Thermal Considerations Package Symbol DO-15 Parameter Value Unit TJ Operating Junction Temperature Range UP °C TS Storage Temperature Range UP °C 60 °C/W R0JA Thermal Resistance: Junction to Ambient Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) ¡$ ¡$ 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) ¡$ - Temperature (tL) 60-150 secs. Peak Temp (TP) ¡$ Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed ¡$ © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down TS(min) Preheat tS 25 time to peak temperature (t 25ºC to peak) 164 Revised: February 22, 2011 Time SIDACtor ® Protection Thyristors Baseband Protection (Voice-DS1) Physical Specifications Environmental Specifications Lead Material Copper Alloy High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ¡$PS¡$ 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Terminal Finish 100% Matte-Tin Plated Temp Cycling ¡$UP¡$NJOEXFMMVQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC¡$ 3)VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage ¡$IST.*-45%.FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock ¡$UP¡$NJOEXFMMTFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) ¡$3)BUNVQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat ¡$TFDT.*-45%.FUIPE Moisture Sensitivity Level 3)¡$ISTSFnPXDZDMFT ¡$1FBL +&%&$+45%-FWFM Body Material UL recognized epoxy meeting flammability classification 94V-0 Part Marking Part Marking Code XXXXX Pxxxx (Refer to Electrical Characteristics Table) Date Code Part Numbering P xxx 0 G x L RP REEL PACK TYPE P = SIDACtor Packing Options RoHS COMPLIANT MEDIAN VOLTAGE IPP RATING CONSTRUCTION VARIABLE Package Type Description Quantity Added Suffix Industry Standard G DO-15 Axial Tape & Reel 5000 RP EIA-RS296-D PACKAGE TYPE Dimensions — DO-15 Dimension D B B L G L Inches Millimeters MIN MAX MIN MAX 0.028 0.034 0.711 0.864 D 0.12 0.14 3.048 3.556 G 0.235 0.27 5.969 6.858 L 1 25.4 Tape and Reel Specification — DO-15 Spacing off center, either side 0.039 (1.0) A 2.55 (64.8) B TYP C D E Dimensions are in inches (and millimeters). Symbols Description Inches MM A Component Spacing (lead to lead) w 5.08 ± 0.508 B C D E F G Inner Tape Pitch Tape Width Max. Off Alignment Reel Dimension Max. Hub Recess Max. Abor Hole w w w w w w 52.37 ± 1.498 6.35 1.219 330.2 76.19 17.27 3.15 (80.0) TYP recess depth max 0.75” G F Direction of Feed © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 165 Revised: February 22, 2011