SIDACtor ® Protection Thyristors SLIC Protection Fixed Voltage Single Port Series - MS-012 Description The series provides single port protection using a fixed voltage switching device for negative surges. Positive surges are routed though internal diodes to a ground reference. The series is also pin-to-pin compatible to industry standard programmable SO-8 SLIC protectors. Features & Benefits Agency Approvals Agency t*OUFHSBUFEEJPEFTGPS positive voltage surges Agency File Number t4JOHMFQPSUQSPUFDUJPOJO one package E133083 t-PXWPMUBHFPWFSTIPPU t%PFTOPUEFHSBEFXJUIVTF t'BJMTTIPSUDJSDVJUXIFO surged in excess of ratings t1JOUPQJO40DPNQBUJCMF footprint t-PXPOTUBUFWPMUBHF Pinout (Tip) 1 8 (Tip) (NC) 2 7 (Ground) (NC) 3 6 (Ground) t5*"" t*&$ (Ring) 4 5 (Ring) t*56,&OIBODFE Level t:%5 Applicable Global Standards t*56,#BTJD-FWFM Schematic Symbol t:%5 t(3*OUFSCVJMEJOH 8 1 t:%5 t(3*OUSBCVJMEJOH 2 7 3 6 4 5 * Series resistance required Electrical Characteristics Part Number P0641DF-1 P0721DF-1 P0901DF-1 P1001DF-1 P1101DF-1 Marking P0641F1 P0721F1 P0901F1 P1001F1 P1101F1 VDRM@ IDRM=5μA VS@100V/μs IH IS IT@VT VT@IT=1 Amps VF@25° V min V max mA min mA max A max V max V max 58 65 75 85 95 77 88 98 110 130 150 150 150 150 150 800 800 800 800 800 1 1 1 1 1 5 5 5 5 5 5 5 5 5 5 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are uni-directional - All electrical characteristics shown are defined from Tip (pins 1 & 8) to Ground (pins 6 & 7), and Ring (pins 4 & 5) to ground (pins 6 & 7) - VF > 8.5 volts @ 10 x 700μs, 37.5 Amps © 2009 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 101 Capacitance See Capacitance Values Table Fixed Voltage Single The MS-012 packaged Fixed Voltage Single Port Series are SIDACtor® devices designed to protect sensitive SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. SIDACtor ® Protection Thyristors SLIC Protection Capacitance Values pF Pin 1,8-6,7 / 4,5-6,7 Tip-Ground, Ring-Ground MIN MAX 40 90 35 85 30 80 25 75 25 70 Part Number Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings ITSM IPP Series F di/dt 2x10μs 1.2x50μs/8x20μs 10x700/5x310μs 10x1000μs 600VRMS 1s A min A min A min A min A min Amps/μs max 120 100 50 30 1 500 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP$ - The device must initially be in thermal equilibrium with -40°C < TJ <¡$ Thermal Considerations Package MS-012 1 2 3 8 7 6 Symbol Parameter Value Unit TJ Operating Junction Temperature Range UP °C TS Storage Temperature Range UP °C R0JA Thermal Resistance: Junction to Ambient 120 °C/W 5 4 V-I Characteristics tr x td Pulse Waveform +I IPP – Peak Pulse Current – %IPP Fixed Voltage Single P0641DF-1 P0721DF-1 P0901DF-1 P1001DF-1 P1101DF-1 pF Pin 1,8-4,5 Tip-Ring MIN MAX 20 45 20 45 20 40 15 35 15 30 VF VS VDRM VT -V +V IDRM IH IS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 IT 0 tr td t – Time (μs) -I 102 © 2009 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. SIDACtor ® Protection Thyristors SLIC Protection Normalized DC Holding Current vs. Case Temperature 2.0 12 1.8 IH 8 6 25 °C 4 2 0 -4 1.6 1.4 25°C 1.2 1.0 0.8 0.6 -6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) TS(max) to TL - Ramp-up Rate Reflow Pb-Free assembly (see Fig. 1) ¡$ ¡$ 60-180 secs. Figure 1 TP 3°C/sec. Max. 3°C/sec. Max. - Temperature (TL) (Liquidus) ¡$ - Temperature (tL) 60-150 secs. Peak Temp (TP) ¡$ Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed ¡$ tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Environmental Specifications Lead Material Copper Alloy High Temp Voltage Blocking 80% Rated VDRM (VDC ¡$PS¡$PS 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Terminal Finish 100% Matte-Tin Plated Temp Cycling ¡$UP¡$NJOEXFMMVQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC¡$ 3)VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage ¡$IST.*-45%.FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock ¡$UP¡$NJOEXFMMTFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) ¡$3)BUNVQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat ¡$TFDT.*-45%.FUIPE Moisture Sensitivity Level 3)¡$ISTSFnPXDZDMFT ¡$1FBL +&%&$+45%-FWFM Body Material UL recognized epoxy meeting flammability classification 94V-0 © 2009 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 103 Fixed Voltage Single 10 IH (TC = 25ºC) 14 Ratio of Percent of VS Change – % Normalized VS Change vs. Junction Temperature SIDACtor ® Protection Thyristors SLIC Protection Dimensions — MS-012 Inches Dimension A A1 A2 B C D E E1 e L o Recommended Soldering Pad Outline (Reference Only) Fixed Voltage Single MIN Millimeters MAX MIN 0.053 0.069 0.004 0.010 0.043 0.065 0.012 0.020 0.007 0.010 0.189 0.197 0.228 0.244 0.150 0.157 0.050 BSC* 0.016 0.050 MAX 1.35 1.75 0.10 0.25 1.25 1.65 0.31 0.51 0.17 0.25 4.80 5.00 5.80 6.20 3.80 4.00 1.27 BSC* 0.40 1.27 * BSC = Basic Spacing between Centers Part Numbering Part Marking P xxx 1 DF -1 SINGLE TYPE P: SIDACtor Part Number Code IPP RATING MEDIAN VOLTAGE (Refer to Electrical Characteristics Table) XXXXXF1 o XXXXX PACKAGE TYPE CONSTRUCTION VARIABLE Date Code Packing Options Package Type Description Quantity Added Suffix Industry Standard D MS-012 SMT 8-pin SOIC Tape and Reel Pack 2500 N/A EIA-481-D Tape and Reel Specifications — MS-012 1.55 (.061) 4.0 (.158) DIMENSIONS ARE: 2.0 (.079) 8.0 (.315) 0.8 MIN. (0.03) 5.5 (.216) o 6.4 (.252) 1.50 ø MIN. (.059) Carrier Tape Embossment 0.512 (13.0) Arbor Hole Dia. MILLIMETERS (INCHES) 0.40 (0.016) 12.0 (.472) Cover 0 MIN. Tape Direction of Feed 2.1 (.083) 12.99 (330.0) Dimensions are in inches (and millimeters). Direction of Feed 0.49 (12.4) 104 © 2009 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information.