SIDACtor ® Protection Thyristors SLIC Protection Fixed Voltage TwinSLIC™ Series - Modified DO-214 Description Fixed Voltage Series Modified DO-214 are unidirectional SIDACtor® devices designed to protect SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. The series provides single port protection using fixed voltage switching devices for negative surges. All positive surges are routed through internal diodes to a ground reference. Features and Benefits t Low voltage overshoot Agency Approvals Agency t Low on-state voltage t Does not degrade with use Agency File Number t Integrated diodes for positive voltage surges t Single-port protection t Fails short circuit when surged in excess of ratings E133083 Applicable Global Standards Pinout Designation Pin 3 Pin 1 Pin 2 t TIA-968-A t GR 1089 Intra-building* t TIA-968-B t IEC 61000-4-5 t ITU K.20/21 Enhanced Level t YD/T 1082 t ITU K.20/21 Basic Level t YD/T 950 t YD/T 993 t GR 1089 Inter-building* Schematic Symbol * Series resistance required 1 (T) 2 (G) 3 (R) Electrical Characteristics Part Number Marking VDRM @lDRM=5μA VS @100V/μs V min V max Pin 1-2, 3-2 P0641CA2LRP P0721CA2LRP P0901CA2LRP P1101CA2LRP P1301CA2LRP P1701CA2LRP P62A P72A P92A P02A P131A P17A 58 65 75 95 120 160 77 88 98 130 160 200 IH IS mA min mA max A max 120 120 120 120 120 120 800 800 800 800 800 800 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are uni-directional © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. IT 93 Revised: February 22, 2011 2.2 2.2 2.2 2.2 2.2 2.2 VT @IT=2.2 Amps VF V max V max 4 4 4 4 4 4 5 5 5 5 5 5 Capacitance See Capacitance Values table SIDACtor ® Protection Thyristors SLIC Protection Capacitance Values pF Pin 1-2 / 3-2 Tip-Ground, Ring-Ground MIN MAX 40 70 35 70 30 65 25 55 25 45 25 40 Part Number P0641CA2LRP P0721CA2LRP P0901CA2LRP P1101CA2LRP P1301CA2LRP P1701CA2LRP pF Pin 1-3 Tip-Ring MIN 20 20 20 15 15 15 MAX 45 45 40 35 30 25 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings Series Series IPP ITSM di/dt 0.2x310 1 0.5x700 2 2x10 1 2x10 2 8x20 1 1.2x50 2 10x160 1 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 50/60 Hz A min A min A min A min A min A min A min A min A min A min A/μs max 20 150 150 90 50 75 75 45 75 20 500 A Notes: 1 Current waveform in μs 2 Voltage waveform in μs - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP$ - The device must initially be in thermal equilibrium with -40°C < TJ <¡$ Thermal Considerations Package Symbol Parameter Value Unit Modified DO-214AA TJ Operating Junction Temperature Range UP °C TS Storage Temperature Range UP °C R0JA Thermal Resistance: Junction to Ambient 85 °C/W Pin 3 Pin 1 Pin 2 V-I Characteristics tr x td Pulse Waveform VS VDRM VF IPP – Peak Pulse Current – %IPP +I VT -V IDRM +V IH IS 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 IT 0 -I © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Peak Value 94 Revised: February 22, 2011 tr td t – Time (μs) SIDACtor ® Protection Thyristors SLIC Protection Normalized DC Holding Current vs. Case Temperature IH 10 8 6 25 °C 4 IH (TC = 25ºC) 2.0 14 12 2 0 -4 1.8 1.6 1.4 25°C 1.2 1.0 Ratio of Percent of VS Change – % Normalized VS Change vs. Junction Temperature 0.8 0.6 -6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) ¡$ ¡$ 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) ¡$ - Temperature (tL) 60-150 secs. Peak Temp (TP) ¡$ Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed ¡$ Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Environmental Specifications Lead Material Copper Alloy High Temp Voltage Blocking 80% Rated VDRM (VAC 1FBL ¡$PS¡$ or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Terminal Finish 100% Matte-Tin Plated Temp Cycling Body Material UL recognized epoxy meeting flammability classification 94V-0 ¡$UP¡$NJOEXFMMVQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC¡$ 3)VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage ¡$IST.*-45%.FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock ¡$UP¡$NJOEXFMMTFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) ¡$3)BUNVQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat ¡$TFDT.*-45%.FUIPE Moisture Sensitivity Level 3)¡$ISTSFnPXDZDMFT¡$ peak). JEDEC-J-STD-020, Level 1 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 95 Revised: February 22, 2011 SIDACtor ® Protection Thyristors SLIC Protection Part Marking Part Numbering P xxx1 C A 2 L RP REEL PACK TYPE P = SIDACtor MEDIAN VOLTAGE TwinSLIC IDENTIFIER (two chip device) CONSTRUCTION VARIABLE Part number code XXXXX XXXXX RoHS COMPLIANT (refer to Electrical Characteristics table) Date code IPP RATING PACKAGE TYPE Dimensions — Modified DO-214AA PIN 3 B D M P A B C D E F G H K M N P A C PIN 1 PIN 2 H E J 0.079 (2.0) 0.079 (2.0) F K G 0.079 (2.0) 0.040 (1.0) 0.110 (2.8) Inches Dimensions N 0.030 (0.76) Dimensions are in inches (and millimeters). Millimeters Min Max Min Max 0.130 0.201 0.077 0.159 0.030 0.075 0.002 0.077 0.006 0.022 0.027 0.052 0.156 0.220 0.087 0.181 0.063 0.096 0.008 0.104 0.016 0.028 0.033 0.058 3.30 5.10 1.95 4.05 0.75 1.90 0.05 1.95 0.15 0.56 0.69 1.32 3.95 5.60 2.20 4.60 1.60 2.45 0.20 2.65 0.41 0.71 0.84 1.47 Pad Outline (MM) Packing Options Package Type C Description Quantity Added Suffix Industry Standard Modified DO-214AA 3-leaded Tape and Reel Pack 2500 RP EIA-481-D Tape and Reel Specification — Modified DO-214AA 0.157 (4.0) Pin 2 0.472 (12.0) 0.360 (9.2) 0.315 (8.0) Pin 1 Pin 3 12.99 (330.0) Dimensions are in inches (and millimeters). 0.512 (13.0) Arbor Hole Dia. Direction of Feed 0.49 (12.4) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Dimensions are in inches (and millimeters). 96 Revised: February 22, 2011