ISL54221 ® Data Sheet December 16, 2008 High-Speed USB 2.0 (480Mbps) Multiplexer FN6820.0 Features • High-Speed (480Mbps) and Full-Speed (12Mbps) Signaling Capability per USB 2.0 The Intersil ISL54221 is a single supply dual 2:1 multiplexer that can operate from a single 2.7V to 5.5V supply. It contains two SPDT (Single Pole/Double Throw) switches configured as a DPDT. The part was designed for switching or routing of USB High-Speed signals and/or USB Full-speed signals in portable battery powered products. • 1.8V Logic Compatible (2.7V to +3.6V supply) • Enable Pin to Open all Switches • Power OFF Protection • D-/D+ Pins Overvoltage Tolerant to 5.5V The 6.7Ω switches can swing rail to rail and were specifically designed to pass USB full-speed data signals that range from 0V to 3.3V and USB high-speed data signals that range from 0V to 400mV. They have high bandwidth and low capacitance to pass USB high-speed data signals with minimal distortion. • -3dB Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . 742MHz • Low ON Capacitance. . . . . . . . . . . . . . . . . . . . . . . . 7.4pF • Low ON-Resistance. . . . . . . . . . . . . . . . . . . . . . . . . . 6.7Ω • Single Supply Operation (VDD) . . . . . . . . . . . . 2.7V to 5.5V The part can be used in Personal Media Players and other portable battery powered devices that need to route USB high-speed signals or full-speed signals to different transceiver sections of the device while connected to a single USB host (computer). • Available in µTQFN Package • Pb-Free (RoHS Compliant) • Compliant with USB 2.0 Short Circuit and Overvoltage Requirements Without Additional External Components The digital logic inputs are 1.8V logic compatible when operated with a 2.7V to 3.6V supply. The ISL54221 has an output enable pin to open all the switches. It can be used to facilitate proper bus disconnect and connection when switching between the USB sources. Applications • MP3 and other Personal Media Players • Cellular/Mobile Phones • PDA’s The ISL54221 is available in a tiny 10 Ld 2.1mmx1.6mm µTQFN package. It operates over a temperature range of -40 to +85°C. • Digital Cameras and Camcorders • USB Switching Application Block Diagram µCONTROLLER VDD ISL54221 SEL USB CONNECTOR OE LOGIC CIRCUITRY VBUS HSD1- D- D- HSD1+ D+ D+ HSD2HSD2+ GND USB HIGH-SPEED OR FULL-SPEED TRANSCEIVER USB HIGH_SPEED OR FULL-SPEED TRANSCEIVER GND PORTABLE MEDIA DEVICE 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2008. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL54221 Pinout VDD ISL54221 10 LD 2.1 X 1.6 µTQFN TOP VIEW 10 LOGIC CONTROL 9 OE 2 8 HSD1- HSD2+ 3 7 HSD2- D+ 4 6 D- SEL 1 HSD1+ GND 5 NOTE: 1. Switches Shown for SEL = Logic “1” and OE = Logic “0”. Truth Table Pin Descriptions OE SEL HSD1-, HSD1+ HSD2-, HSD2+ PIN NAME 0 0 ON OFF VDD Power Supply 0 1 OFF ON GND Ground Connection 1 X OFF OFF SEL Select Logic Control Input OE Bus Switch Enable Logic “0” when ≤ 0.5V, Logic “1” when ≥ 1.4V with a 2.7V to 3.6V Supply. DESCRIPTION D+, D-, HSDx+, HSDx- USB Data Port Ordering Information PART NUMBER (Note) ISL54221IRUZ-T* PART MARKING GL TEMP. RANGE (°C) -40 to +85 PACKAGE (Pb-Free) 10 Ld 2.1x1.6mm µTQFN (Tape and Reel) PKG. DWG. # L10.2.1x1.6A *Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and NiPdAu plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 2 FN6820.0 December 16, 2008 ISL54221 Absolute Maximum Ratings Thermal Information VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 6.5V Input Voltages HSD2x, HSD1x (Note 2). . . . . . . . . . . . . . . . . . . . . . -0.3V to 6.5V SEL, OE (Note 2) . . . . . . . . . . . . . . . . . . . . -0.3 to ((VDD) + 0.3V) Output Voltages D+, D- (Note 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6.5V Continuous Current (HSD2x, HSD1x) . . . . . . . . . . . . . . . . . . ±40mA Peak Current (HSD2x, HSD1x) (Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . ±100mA ESD Rating: Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>6kV Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>500V Charged Device Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>2kV Thermal Resistance (Typical, Note 3) θJA (°C/W) 10 Ld µTQFN Package . . . . . . . . . . . . . . . . . . . . . . 155 Maximum Junction Temperature (Plastic Package). . . . . . . +150°C Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C VDD Supply Voltage Range . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V Logic Control Input Voltage . . . . . . . . . . . . . . . . . . . . . . . 0V to VDD Analog Signal Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to VDD CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 2. Signals on HSD1x, HSD2x, D+,D- exceeding GND by specified amount are clamped. Signals on OE and SEL exceeding VDD or GND by specified amount are clamped. Limit current to maximum current ratings. 3. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. Electrical Specifications - 2.7V to 5.5V Supply Test Conditions: VDD = +3.3V, GND = 0V, VSELH = 1.4V, VSELL = 0.5V, VOEH = 1.4V, VOEL = 0.5V, (Note 4), Unless Otherwise Specified PARAMETER TEST CONDITIONS TEMP MIN (°C) (Notes 5, 6) TYP MAX (Notes 5, 6) UNITS ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG VDD = VDD, SEL = 0V or VDD, OE = 0V Full 0 - VDD V ON-Resistance, rON (High-Speed) VDD = 2.7V, SEL = 0.5V or 1.4V, OE = 0.5V, IDx = 40mA, VHSD1x or VHSD2 x = 0V to 400mV (see Figure 3, Note 9) 25 - 6.7 8 Ω Full - - 10 Ω 25 - 0.117 0.45 Ω Full - - 0.55 Ω 25 - 0.94 1.2 Ω Full - - 1.3 Ω 25 -15 0.31 15 nA Full -20 - 20 nA 25 -20 2.2 20 nA Full -25 - 25 nA 25 -15 0.26 15 nA Full -20 - 20 nA 25 -20 2.1 20 nA Full -25 - 25 nA 25 - 0.0047 0.025 µA Full - - 0.40 µA rON Matching Between Channels, ΔrON (High-Speed) VDD = 2.7V, SEL = 0.5V or 1.4V, OE = 0.5V, IDx = 40mA, V VHSD1x or VHSD2 x = Voltage at max rON, (Notes 8, 9) rON Flatness, RFLAT(ON) (High-Speed) VDD = 2.7V, SEL = 0.5V or 1.4V, OE = 0.5V, IDx = 40mA, VHSD1x or VHSD2 x = 0V to 400mV, (Notes 7, 9) OFF Leakage Current, IHSD1x(OFF) VDD = 5.5V, SEL = VDD and OE = 0V or OE = VDD, VDx = 0.3V, 3.3V, VHSD1X = 3.3V, 0.3V, VHSD2x = 0.3V, 3.3V ON Leakage Current, IHSD1x(ON) VDD = 5.5V, SEL = OE = 0V, VDx = 0.3V, 3.3V, VHSD1X = 0.3V, 3.3V, VHSD2x = 3.3V, 0.3V OFF Leakage Current, IHSD2x(OFF) VDD = 5.5V, SEL = OE = 0V or OE = VDD, VDx = 3.3V, 0.3V, VHSD2x = 0.3V, 3.3V, VHSD1X = 3.3V, 0.3V ON Leakage Current, IHSD2x(ON) VDD = 5.5V, SEL = VDD, OE = 0V, VDx= 0.3V, 3.3V, VHSD2x = 0.3V, 3.3V, VHSD1X = 3.3V, 0.3V Power OFF Leakage Current, ID+, ID- VDD = 0V, VD+ = 0V to 5.25V, VD-= 0V to 5.25V, SEL = OE = VDD DYNAMIC CHARACTERISTICS Turn-ON Time, tON VDD = 3.3V, RL = 50Ω, CL = 10pF (see Figure 1) 25 - 35 - ns Turn-OFF Time, tOFF VDD = 3.3V, RL = 50Ω, CL = 10pF (see Figure 1) 25 - 27 - ns Break-Before-Make Time Delay, tD VDD = 3.3V, RL = 50Ω, CL = 10pF (see Figure 2) 25 - 10 - ns 3 FN6820.0 December 16, 2008 ISL54221 Electrical Specifications - 2.7V to 5.5V Supply Test Conditions: VDD = +3.3V, GND = 0V, VSELH = 1.4V, VSELL = 0.5V, VOEH = 1.4V, VOEL = 0.5V, (Note 4), Unless Otherwise Specified (Continued) PARAMETER TEST CONDITIONS TEMP MIN (°C) (Notes 5, 6) TYP MAX (Notes 5, 6) UNITS Skew, (tSKEWOUT - tSKEWIN) VDD = 3.3V, SEL = 0V or 3.3V, OE = 0V, RL = 45Ω, CL = 10pF, tR = tF = 720ps at 480Mbps, (Duty Cycle = 50%) (see Figure 6) 25 - 50 - ps Rise/Fall Degradation (Propagation Delay), tPD VDD = 3.3V, SEL = 0V or 3.3V, OE = 0V, RL = 45Ω, CL = 10pF (see Figure 6) 25 - 250 - ps Crosstalk VDD = 3.3V, RL = 50Ω, f = 240MHz (see Figure 5) 25 - -36 - dB OFF-Isolation VDD = 3.3V, OE = 3.3V, RL = 50Ω, f = 240MHz 25 - -32 - dB -3dB Bandwidth Signal = 0dBm, 0.2Vdc offset, RL = 50Ω 25 - 742 - MHz OFF Capacitance, CHSxOFF f = 1MHz, VDD = 3.3V, SEL = 0V, OE = 3.3V, VHSD1x or VHSD2x = VDx = 0V (see Figure 4) 25 - 2.8 - pF COM ON Capacitance, CDX(ON) f = 1MHz, VDD = 3.3V, SEL = 0V or 3.3V, OE = 0V, VHSD1x or VHSD2x = VDx = 0V (see Figure 4) 25 - 7.4 - pF Full 2.7 5.5 V 25 - 0.009 0.03 µA Full - - 1 µA 25 - 0.159 0.6 µA Full - - 1.6 µA 25 - 6.6 10 µA Full - - 12 µA POWER SUPPLY CHARACTERISTICS Power Supply Range, VDD Positive Supply Current, IDD VDD = 5.5V, SEL = 0V or VDD, OE = 0V or VDD Positive Supply Current, IDD VDD = 4.3V, SEL = 2.6V, OE = 0V or 2.6V Positive Supply Current, IDD VDD = 3.6V, SEL = 1.4V, OE = 0V or 1.4V DIGITAL INPUT CHARACTERISTICS Input Voltage Low, VSELL, VOEL VDD = 2.7V to 3.6V Full - - 0.5 V Input Voltage High, VSELH, VOEH VDD = 2.7V to 3.6V Full 1.4 - - V Input Voltage Low, VSELL, VOEL VDD = 4.3V to 5.5V Full - - 0.8 V Input Voltage High, VSELH, VOEH VDD = 4.3V to 5.5V Full 2.0 - - V Input Current, ISELL, IOEL VDD = 5.5V, SEL = 0V, OE = 0V Full - 3.3 - nA Input Current, ISELH VDD = 5.5V, SEL = 5.5V Full - -3.6 - nA Input Current, IOEH VDD = 5.5V, OE = 5.5V Full - -8.2 - nA NOTES: 4. VLOGIC = Input voltage to perform proper function. 5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. 6. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. 7. Flatness is defined as the difference between maximum and minimum value of ON-resistance over the specified analog signal range 8. rON matching between channels is calculated by subtracting the channel with the highest max rON value from the channel with lowest max rON value, between HSD2+ and HSD2- or between HSD1+ and HSD1-. 9. Limits established by characterization and are not production tested. 4 FN6820.0 December 16, 2008 ISL54221 Test Circuits and Waveforms VDD LOGIC INPUT VDD tr < 20ns tf < 20ns 50% 0V VINPUT tOFF SWITCH INPUT VINPUT SWITCH INPUT VOUT HSDxx Dx SEL VOUT 90% 90% SWITCH OUTPUT C VIN RL 50Ω OE GND 0V CL 10pF tON Repeat test for all switches. CL includes fixture and stray capacitance. RL V OUT = V (INPUT) -----------------------R L + r ON Logic input waveform is inverted for switches that have the opposite logic sense. FIGURE 1A. MEASUREMENT POINTS FIGURE 1B. TEST CIRCUIT FIGURE 1. SWITCHING TIMES VDD C VDD LOGIC INPUT HSD2x VINPUT 0V RL 50Ω SEL SWITCH OUTPUT VOUT 90% GND VIN 0V VOUT Dx HSD1x CL 10pF OE tD Repeat test for all switches. CL includes fixture and stray capacitance. FIGURE 2B. TEST CIRCUIT FIGURE 2A. MEASUREMENT POINTS FIGURE 2. BREAK-BEFORE-MAKE TIME VDD C rON = V1/40mA HSDx VHSDX SEL V1 40mA OV OR VDD Dx GND OE Repeat test for all switches. FIGURE 3. rON TEST CIRCUIT 5 FN6820.0 December 16, 2008 ISL54221 Test Circuits and Waveforms (Continued) VDD VDD C C SIGNAL GENERATOR HSDxx HSD1x SEL SEL IMPEDANCE ANALYZER 0V OR VDD Dx GND OE VIN Dx ANALYZER HSD2x GND RL Repeat test for all switches. 50Ω Dx NC OE Signal direction through switch is reversed, worst case values are recorded. Repeat test for all switches. FIGURE 4. CAPACITANCE TEST CIRCUIT FIGURE 5. CROSSTALK TEST CIRCUIT VDD C tri 90% DIN+ 10% 50% VIN tskew_i DIN- 90% SEL 15.8Ω DIN+ 50% 143Ω 10% DIN- tfi tro 15.8Ω OUT+ D2 COMD2 CL COMD1 143Ω OUT- D1 OE 45Ω CL 45Ω 90% OUT+ OUT- 10% 50% GND tskew_o 50% 90% 10% tf0 |tro - tri| Delay Due to Switch for Rising Input and Rising Output Signals. |tfo - tfi| Delay Due to Switch for Falling Input and Falling Output Signals |tskew_0| Change in Skew through the Switch for Output Signals. |tskew_i| Change in Skew through the Switch for Input Signals. FIGURE 6A. MEASUREMENT POINTS FIGURE 6B. TEST CIRCUIT FIGURE 6. SKEW TEST 6 FN6820.0 December 16, 2008 ISL54221 Application Block Diagram µCONTROLLER VDD ISL54221 SEL USB CONNECTOR OE LOGIC CIRCUITRY VBUS HSD1- D- D- HSD1+ D+ D+ HSD2HSD2+ GND USB HIGH-SPEED OR FULL-SPEED TRANSCEIVER USB HIGH_SPEED OR FULL-SPEED TRANSCEIVER GND PORTABLE MEDIA DEVICE Detailed Description The ISL54221 device is a dual single pole/double throw (SPDT) analog switch configured as a DPDT that operates from a single DC power supply in the range of 2.7V to 5.5V. It was designed to function as a dual 2-to-1 multiplexer to select between two USB high-speed differential data signals in portable battery powered products. It is offered in a small µTQFN package for use in MP3 players, cameras, PDAs, cellphones, and other personal media players. The device has an enable pin to open all switches. The part consists of four 6Ω high-speed (HSx) switches. These switches have high bandwidth and low capacitance to pass USB high-speed (480Mbps) differential data signals with minimal edge and phase distortion. They can also swing from 0V to VDD to pass USB full-speed (12Mbps) differential data signals with minimal distortion. The ISL54221 was designed for MP3 players, cameras, cellphones, and other personal media player applications that have multiple high-speed or full-speed transceivers sections and need to multiplex between these USB sources to a single USB host (computer). A typical application block diagram of this functionality is shown on page 7. A detailed description of the HS switches is provided in the following section. High-Speed (HSx) Switches The HSx switches (HSD1-, HSD1+, HSD2-, HSD2+) are bi-directional switches that can pass rail-to-rail signals. When powered with a 3.3V supply, these switches have a nominal rON of 6Ω over the signal range of 0V to 400mV with a rON flatness of 0.94Ω. The rON matching between the 7 HSD1 and HSD2 switches over this signal range is only 0.12Ω, ensuring minimal impact by the switches to USB high-speed signal transitions. As the signal level increases, the rON switch resistance increases. At signal level of 3.3V, the switch resistance is nominally 129Ω. See Figures 7, 8, 9 and 10 in the “Typical Performance Curves” on page 9. The HSx switches were specifically designed to pass USB 2.0 high-speed (480Mbps) differential signals in the range of 0V to 400mV. They have low capacitance and high bandwidth to pass the USB high-speed signals with minimum edge and phase distortion to meet USB 2.0 high-speed signal quality specifications. See Figure 11 in the “Typical Performance Curves” on page 10 for USB High-speed Eye Pattern taken with switch in the signal path. The HSx switches can also pass USB full-speed signals (12Mbps) with minimal distortion and meet all the USB requirements for USB 2.0 full-speed signaling. See Figure 12 in the “Typical Performance Curves” on page 11 for the USB Full-speed Eye Pattern taken with switch in the signal path. The maximum normal operating signal range for the HSx switches is from 0V to VDD. The signal voltage should not be allow to exceed the VDD voltage rail or go below ground by more than 0.3V for normal operation. However in the event that the USB 5.25V VBUS voltage gets shorted to one or both of the D-/D+ pins, the ISL54221 has special fault protection circuitry to prevent damage to the ISL54221 part. The fault circuitry allows the signal pins (D-, D+, HS1D-, HS1D+, HS2D-, HS2D+) to be driven up to 5.5V while the VDD supply voltage is in the range of 0V to 5.5V. In this condition the part draws < 500µA of current and causes no stress to the IC. In addition when VDD is at 0V (ground) FN6820.0 December 16, 2008 ISL54221 all switches are OFF and the fault voltage is isolated from the other side of the switch. When VDD is in the range of 2.7V to 5.5V the fault voltage will pass through to the output of an active switch channel. The HS1 channel switches are active (turned ON) whenever the SEL voltage is logic”0”(Low) and the OE voltage is logic”0”(Low). The HS2 channel switches are active (turned ON) whenever the SEL voltage is logic “1” (High) and the OE voltage is logic “0” (Low). ISL54221 Operation The following will discuss using the ISL54221 the “Application Block Diagram” on page 7. POWER The power supply connected at the VDD pin provides the DC bias voltage required by the ISL54221 part for proper operation. The ISL54221 can be operated with a VDD voltage in the range of 2.7V to 5.5V. When used in a USB application, the VDD voltage should be kept in the range of 3.0V to 5.5V to ensure you get the proper signal levels for good signal quality. A 0.01µF or 0.1µF decoupling capacitor should be connected from the VDD pin to ground to filter out any power supply noise from entering the part. The capacitor should be located as close to the VDD pin as possible. In a typical application, VDD will be in the range of 2.8V to 4.3V and will be connected to the battery or LDO of the portable media device. With VDD supply voltage in the range of 4.3V to 5.5V the logic levels are: OE = Logic “0” (Low) when VOE ≤ 0.8V OE = Logic “1” (High) when VOE ≥ 2.0V SEL = Logic “0” (Low) when VSEL ≤ 0.8V SEL = Logic “1” (High) when VSEL ≥ 2.0V HSD1 USB Channel If the SEL pin = Logic “0” and the OE pin = Logic “0”, high-speed Channel 1 will be ON. The HSD1- and HSD1+ switches are ON and the HSD2- and HSD2+ switches are OFF (high impedance). When a computer or USB hub is plugged into the common USB connector and channel one is active, a link will be established between the USB 1 driver section of the media player and the computer. The device will be able to transmit and receive data from the computer at a data rate of 480Mbps. HSD2 USB Channel If the SEL pin = Logic “1” and the OE pin = Logic “0”, high-speed Channel 2 will be ON. The HSD2- and HSD2+ switches are ON and the HSD1- and HSD1+ switches are OFF (high impedance). When a USB cable from a computer or USB hub is connected at the common USB connector and the part has Channel 2 active, a link will be established between the USB 2 driver section of the media player and the computer. The device will be able to transmit and receive data from the computer at a data rate of 480Mbps. All Switches OFF Mode LOGIC CONTROL The state of the ISL54221 device is determined by the voltage at the SEL pin and the OE pin. SEL is only active when the OE pin is logic “0” (Low). Refer to “Truth Table” on page 2. The ISL54221 logic pins are designed to minimize current consumption when the logic control voltage is lower than the VDD supply voltage. With VDD = 3.6V and logic pins at 1.4V the part typically draws only 6.6µA. With VDD = 4.3V and logic pins at 2.6V the part typically draws only 0.2µA. Driving the logic pins to the VDD supply rail minimizes power consumption. The logic pins must be held High or Low and must not float. Logic Control Voltage Levels With VDD supply voltage in the range of 2.7V to 3.6V the logic levels are: OE = Logic “0” (Low) when VOE ≤ 0.5V OE = Logic “1” (High) when VOE ≥ 1.4V SEL = Logic “0” (Low) when VSEL ≤ 0.5V SEL = Logic “1” (High) when VSEL ≥ 1.4V 8 If the SEL pin = Logic “0” or Logic “1” and the OE pin = Logic “1”, all of the switches will turn OFF (high impedance). The all OFF state can be used to switch between the two USB sections of the media player. When disconnecting from one USB device to the other USB device, you can momentarily put the ISL54221 switch in the “all off” state in order to get the computer to disconnect from the one device so it can properly connect to the other USB device when that channel is turned ON. USB 2.0 VBUS Short Requirements The USB specification in section 7.1.1 states a USB device must be able to withstand a VBUS short to the D+ or Dsignal lines when the device is either powered off or powered on for at least 24 hours. The ISL54220 part has special fault protection circuitry to meet these short circuit requirements. The fault protection circuitry allows the signal pins (D-, D+, HS1D-, HS1D+, HS2D-, HS2D+) to be driven up to 5.5V while the VDD supply voltage is in the range of 0V to 5.5V. In this overvoltage condition the part draws < 500µA of current and causes no stress/damage to the IC. FN6820.0 December 16, 2008 ISL54221 In addition when VDD is at 0V (ground) all switches are OFF and the shorted VBUS voltage is isolated from the other side of the switch. When VDD is in the range of 2.7V to 5.5V the shorted VBUS voltage will pass through to the output of an active (turned ON) switch channel but not through a turned OFF channel. Any components connected on the active channel must be able to withstand the overvoltage condition. Note: During the fault condition normal operation of the USB channel is not guaranteed until the fault condition is removed. Typical Performance Curves TA = +25°C, Unless Otherwise Specified 200 8 ICOM = 1mA ICOM = 40mA VDD = 3.0V 150 7 VDD = 2.7V rON (Ω) rON (Ω) VDD = 2.7V VDD = 3.6V 5 50 VDD = 5.5V 4 0 0.05 0.10 0.15 0.20 0.25 VCOM (V) VDD = 3.3V 100 VDD = 3.3V 6 0.30 0.35 0 0.40 FIGURE 7. ON-RESISTANCE vs SUPPLY VOLTAGE vs SWITCH VOLTAGE 0 0.5 1.0 2.5 3.0 3.3 FIGURE 8. ON-RESISTANCE vs SUPPLY VOLTAGE vs SWITCH VOLTAGE 9 8 V+ = 2.7V ICOM = 40mA +85°C 8 V+ = 3.3V ICOM = 40mA 7 +85°C 6 7 +25°C rON (Ω) +25°C rON (Ω) 1.5 2.0 VCOM (V) 6 5 -40°C -40°C 5 4 4 3 3 0 0.1 0.2 VCOM (V) 0.3 FIGURE 9. ON-RESISTANCE vs SWITCH VOLTAGE 9 0.4 2 0 0.1 0.2 VCOM (V) 0.3 0.4 FIGURE 10. ON-RESISTANCE vs SWITCH VOLTAGE FN6820.0 December 16, 2008 ISL54221 Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued) VDD = 3.3V VOLTAGE SCALE (0.1V/DIV) VDD = 3.3V TIME SCALE (0.2ns/DIV) FIGURE 11. EYE PATTERN: 480Mbps WITH SWITCHES IN THE SIGNAL PATH 10 FN6820.0 December 16, 2008 ISL54221 Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued) VOLTAGE SCALE (0.5V/DIV) VDD = 3.3V TIME SCALE (10ns/DIV) 1 -10 0 -20 -1 -30 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) FIGURE 12. EYE PATTERN: 12Mbps WITH SWITCHES IN THE SIGNAL PATH -2 -3 -4 RL = 50Ω VIN = 0dBm, 0.2VDC BIAS RL = 50Ω VIN = 0dBm, 0.2VDC BIAS -40 -50 -60 -70 -80 -90 -100 1M 10M 100M FREQUENCY (Hz) FIGURE 13. FREQUENCY RESPONSE 11 1G -110 0.001 0.01 0.1 1M 10M FREQUENCY (Hz) 100M 500M FIGURE 14. OFF-ISOLATION FN6820.0 December 16, 2008 ISL54221 Typical Performance Curves TA = +25°C, Unless Otherwise Specified (Continued) Die Characteristics -10 -20 RL = 50Ω VIN = 0dBm, 0.2VDC BIAS SUBSTRATE POTENTIAL (POWERED UP): GND NORMALIZED GAIN (dB) -30 TRANSISTOR COUNT: -40 325 -50 PROCESS: -60 Submicron CMOS -70 -80 -90 -100 -110 0.001 0.01 0.1 1M 10M FREQUENCY (Hz) 100M 500M FIGURE 15. CROSSTALK 12 FN6820.0 December 16, 2008 ISL54221 Ultra Thin Quad Flat No-Lead Plastic Package (UTQFN) D 6 INDEX AREA A L10.2.1x1.6A B N 10 LEAD ULTRA THIN QUAD FLAT NO-LEAD PLASTIC PACKAGE MILLIMETERS E SYMBOL 2X MIN NOMINAL MAX 1 2X 2 0.10 C TOP VIEW C A 0.05 C SEATING PLANE 1 0.45 0.50 0.55 - A1 - - 0.05 - 0.127 REF - b 0.15 0.20 0.25 5 D 2.05 2.10 2.15 - E 1.55 1.60 1.65 - A1 e SIDE VIEW k 0.20 - - L 0.35 0.40 0.45 (DATUM A) PIN #1 ID A A3 0.10 C 4xk 2 NX L 0.50 BSC - NX b e 2 Nd 4 3 Ne 1 3 0 12 - NOTES: 5 BOTTOM VIEW CL (A1) L 5 e SECTION "C-C" TERMINAL TIP C C 4 Rev. 3 6/06 0.10 M C A B 0.05 M C 3 (ND-1) X e - 10 (DATUM B) N-1 - N θ N NX (b) NOTES 0.10 C FOR ODD TERMINAL/SIDE b 1. Dimensioning and tolerancing conform to ASME Y14.5-1994. 2. N is the number of terminals. 3. Nd and Ne refer to the number of terminals on D and E side, respectively. 4. All dimensions are in millimeters. Angles are in degrees. 5. Dimension b applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 7. Maximum package warpage is 0.05mm. 8. Maximum allowable burrs is 0.076mm in all directions. 9. Same as JEDEC MO-255UABD except: No lead-pull-back, "A" MIN dimension = 0.45 not 0.50mm "L" MAX dimension = 0.45 not 0.42mm. 10. For additional information, to assist with the PCB Land Pattern Design effort, see Intersil Technical Brief TB389. 2.50 1.75 0.05 MIN L 2.00 0.80 0.275 0.10 MIN DETAIL “A” PIN 1 ID 0.50 0.25 LAND PATTERN 10 All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 13 FN6820.0 December 16, 2008