INTERSIL ISL80121-5

1A Ultra Low Dropout Linear Regulator with
Programmable Current Limiting
ISL80121-5
Features
The ISL80121-5 is a low dropout voltage, single output LDO with
programmable current limiting. This LDO operates from input
voltages of 2.2V to 6V. The ISL80121-5 has a nominal output
voltage of 5V. Other custom voltage options are available upon
request.
• ±1.8% VOUT Accuracy Guaranteed Over Line, Load and
TJ = -40°C to +125°C
• Very Low 130mV Dropout Voltage at VIN = 5.0V
• High Accuracy Current Limit Programmable up to 1.75A
• Very Fast Transient Response
A sub-micron BiCMOS process is utilized for this product family to
deliver the best in class analog performance and overall value.
The programmable current limiting improves system reliability of
applications. An external capacitor on the soft-start pin provides
an adjustable soft-starting ramp. The ENABLE feature allows the
part to be placed into a low quiescent current shutdown mode.
• 200µVRMS Output Noise
• Power Good Output
• Programmable Soft-starting
• Over-Temperature Protection
• Small 10 Ld DFN Package
This CMOS LDO will consume significantly lower quiescent
current as a function of load compared to bipolar LDOs, which
translates into higher efficiency and packages with smaller
footprints. Quiescent current is modestly compromised to
achieve a very fast load transient response.
Applications
• USB devices
• Telecommunications and Networking
• Medical Equipment
• Instrumentation Systems
• Routers and Switchers
• Gaming
Typical Applications
5.4V ±10%
VIN
CIN
ISL80121-5
10
9
10µF
8
ON
7
OFF
6
VIN
VOUT
VOUT
VIN
ISET
SENSE
2
3
ISL80121-5
5.4V ±10%
VIN
10
COUT
CIN
9
10µF
10µF
8
RPG
100kΩ
VIN
VOUT
VIN
VOUT
SENSE
ISET
ENABLE
SS
PG
2
PGOOD
6
LIMIT
= 0.75A
(default)
1
CSS
COUT
10µF
RPG
100kΩ
7
OFF
RSENSE
10Ω
3
RISET
10kΩ
GND
5
I
4
5.0V ±1.8%
VOUT
1
ON
CSS
December 8, 2010
FN7713.1
1
5.0V ±1.8%
VOUT
ENABLE
SS
PG
4
GND
PGOOD
5
2.9
I LIMIT = 0.75 + ------------------------------------R SET ( kΩ )
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2010. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners
ISL80121-5
Block Diagram
SS
THERMAL
SHUTDOWN
VIN
CURRENT
LIMITER
VOUT
ISET
PGOOD
VOLTAGE
REFERENCE
POWER
GOOD
ADJ
ADJUSTABLE
VOLTAGE
VERSION
SENSE
FIXED VOLTAGE
VERSION
ENABLE
GND
Ordering Information
PART NUMBER
(Notes 1, 2, 4)
ISL80121IR50Z
PART
MARKING
DZAD
VOUT VOLTAGE
(Note 3)
TEMP. RANGE
(°C)
5.0V
-40 to +125
PACKAGE
(Pb-Free)
10 Ld 3x3 DFN
PKG
DWG. #
L10.3x3
NOTES:
1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. The 1.5V, 3.3V and 5V fixed output voltages will be released in the future. Please contact Intersil Marketing for more details.
4. For Moisture Sensitivity Level (MSL), please see device information page for ISL80121-5. For more information on MSL, please see Technical Brief
TB363.
2
FN7713.1
December 8, 2010
ISL80121-5
Pin Configuration
ISL80121-5
(10 LD 3x3 DFN)
TOP VIEW
VOUT
1
VOUT
2
SENSE
3
10 VIN
PAD
9
VIN
8
ISET
PG
4
7
ENABLE
GND
5
6
SS
Pin Descriptions
PIN NUMBER
PIN NAME
DESCRIPTION
1, 2
VOUT
3
SENSE
4
PG
5
GND
6
SS
7
ENABLE
8
ISET
Current limit setting. Current limit is 0.75mA when this pin is left floating. This default value can be increased by
tying RSET to GND, or decreased by tying RSET to VIN. See “Programmable Current Limit” on page 7 in the
“Functional Description” for more details. Do not short this pin to ground.
9, 10
VIN
Input supply. A minimum of 10µF X5R/X7R input capacitor is required for stability. See “External Capacitor
Requirements” on page 8 in “Functional Description” for more details.
-
EPAD
Output voltage. A minimum 10µF X5R/X7R output capacitor is required for stability. See “External Capacitor
Requirements” on page 8 in the “Functional Description” for more details.
Remote voltage sense for internally fixed VOUT options. Parasitic resistance between the VOUT pin and the load
causes small voltage drops which degrade VOUT accuracy. For applications that require a stiff VOUT, connect the
sense pin to the load.
VOUT in regulation signal. Logic low indicates VOUT is not in regulation, and must be grounded if not used.
Ground.
External capacitor adjusts in-rush current.
VIN-independent chip enable. TTL and CMOS compatible.
EPAD at ground potential. Soldering it directly to GND plane is optional.
3
FN7713.1
December 8, 2010
ISL80121-5
Absolute Maximum Ratings
Thermal Information
(Note 7)
VIN Relative to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6.5V
VOUT Relative to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6.5V
PG, ENABLE, SENSE, SS, ISET
Relative to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +6.5V
ESD Rating
Human Body Model (Tested per JESD22-A114) . . . . . . . . . . . . . . . .2.5kV
Machine Model (Tested per JESD22-A115). . . . . . . . . . . . . . . . . . . 250V
Latch Up (Tested per JESD78). . . . . . . . . . . . . . . . . . . . . . .±100mA @ 85°C
Thermal Resistance (Typical)
θJA (°C/W) θJC (°C/W)
10 Ld 3x3 DFN Package (Notes 5, 6). . . . .
51
7
Maximum Junction Temperature (Plastic Package) . . . . . . . . . . . .+150°C
Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Recommended Operating Conditions (Note 8)
Junction Temperature Range (TJ) . . . . . . . . . . . . . . . . . . .-40°C to +125°C
VIN Relative to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.2V to 6V
VOUT Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800mV to 5V
PG, ENABLE, SENSE, SS, ISET Relative to GND. . . . . . . . . . . . . . . . 0V to 6V
PG Sink Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10mA
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
5. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
6. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.
7. Absolute maximum voltage rating is defined as the voltage applied for a lifetime average duty cycle above 6V of 1%.
8. Electromigration specification defined as lifetime average junction temperature of +110°C where max rated DC current = lifetime average current.
Electrical Specifications Unless otherwise noted, all parameters are established over the following specified conditions: VIN = VOUT + 0.4V,
VOUT = 5.0V, CIN = COUT = 10µF, TJ = +25°C, ILOAD = 0A. Applications must follow thermal guidelines of the package to determine worst case
junction temperature. Please refer to “Functional Description” on page 7 and Tech Brief TB379. Boldface limits apply over the operating
temperature range, -40°C to +125°C. Pulse load techniques used by ATE to ensure TJ = TA defines established limits.
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
(Note 9)
TYP
MAX
(Note 9)
UNITS
-1.8
%
1
%
DC CHARACTERISTICS
DC Output Voltage Accuracy
VOUT
ΔVOUT/ΔVIN
DC Input Line Regulation
ΔVOUT
DC Output Load Regulation
Ground Pin Current
IQ
Ground Pin Current in Shutdown
ISHDN
Dropout Voltage (Note 10)
VDO
Output Current Limit
ILIMIT
VOUT + 0.4V < VIN < 6V; 0A < ILOAD < 1A
-1.8
VOUT + 0.4V < VIN < 6.0V, VOUT = 5.0V
0A < ILOAD < 1A
-1
%
ILOAD = 0A, 2.2V < VIN < 6V
3
5
mA
ILOAD = 1A, 2.2V < VIN < 6V
5
7
mA
ENABLE Pin = 0.2V, VIN = 6V
0.2
12
µA
ILOAD = 1A, VIN = 5.0V, VSENSE = 0V
90
130
mV
0.75
0.84
A
VOUT = 4.75V, VOUT + 0.4V < VIN < 6V, ISET is floating
0.66
VOUT = 4.75V, VOUT + 0.4V < VIN < 6V, RSET = 19.33kΩ
0.9
A
Thermal Shutdown Temperature
TSD
VOUT + 0.4V < VIN < 6V
160
°C
Thermal Shutdown Hysteresis
(Rising Threshold)
TSDn
VOUT + 0.4V < VIN < 6V
30
°C
PSRR
f = 1kHz, ILOAD = 1A
58
dB
f = 120Hz, ILOAD = 1A
62
dB
ILOAD = 10mA, BW = 10Hz < f < 100kHz
210
µVRMS
AC CHARACTERISTICS
Input Supply Ripple Rejection
Output Noise Voltage
ENABLE PIN CHARACTERISTICS
Turn-on Threshold
VEN(HIGH)
2.2V < VIN < 6V
0.3
0.8
1.0
V
Hysteresis (Rising Threshold)
VEN(HYS)
2.2V < VIN < 6V
10
80
200
mV
4
FN7713.1
December 8, 2010
ISL80121-5
Electrical Specifications Unless otherwise noted, all parameters are established over the following specified conditions: VIN = VOUT + 0.4V,
VOUT = 5.0V, CIN = COUT = 10µF, TJ = +25°C, ILOAD = 0A. Applications must follow thermal guidelines of the package to determine worst case
junction temperature. Please refer to “Functional Description” on page 7 and Tech Brief TB379. Boldface limits apply over the operating
temperature range, -40°C to +125°C. Pulse load techniques used by ATE to ensure TJ = TA defines established limits. (Continued)
PARAMETER
SYMBOL
Enable Pin Turn-on Delay
tEN
TEST CONDITIONS
MIN
(Note 9)
COUT = 10µF, ILOAD = 1A
TYP
100
VIN = 6V, EN = 3V
Enable Pin Leakage Current
MAX
(Note 9)
UNITS
µs
1
µA
SOFT-START CHARACTERISTICS
Reset Pull-Down Current
IPD
Soft-Start Charge Current
ICHG
EN = 0V, SS = 1V
0.5
1
1.3
mA
-3.3
-2
-0.8
µA
75
85
92
%VOUT
PG PIN CHARACTERISTICS
VOUT PG Flag Threshold
VOUT PG Flag Hysteresis
4
PG Flag Low Voltage
ISINK = 500µA
PG Flag Leakage Current
VIN = 6V, PG = 6V
%
47
100
mV
0.05
1
µA
NOTES:
9. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.
10. Dropout is defined by the difference in supply VIN and VOUT when the output is below its nominal regulation.
11. Minimum capacitor of 10µF X5R/X7R on VIN and VOUT required for stability.
12. If the current limit for in-rush current is acceptable in application, do not use this feature. Used only when large bulk capacitance required on VOUT for
application.
5
FN7713.1
December 8, 2010
ISL80121-5
Typical Operating Performance
Unless otherwise noted: VIN = 5.4V, VOUT = 5.0V, CIN = COUT = 10µF,
TJ = +25°C, IL = 0A.
1.8
150
1.2
0.6
+125°C
90
DVOUT (%)
DROPOUT (mV)
120
+25°C
60
0
-0.6
-40°C
30
0
-1.2
0
0.2
0.4
0.6
LOAD CURRENT (A)
0.8
-1.8
-50
1.0
0
25
50
75
3.30
GROUND CURRENT (mA)
+25°C
0
-40°C
+125°C
150
+25°C
3.25
1.2
-0.6
125
FIGURE 2. OUTPUT VOLTAGE vs TEMPERATURE
1.8
0.6
100
JUNCTION TEMPERATURE (°C)
FIGURE 1. DROPOUT VOLTAGE vs LOAD
DVOUT (%)
-25
-1.2
+125°C
3.20
3.15
-40°C
3.10
3.05
3.00
2.95
2.90
-1.8
0.25
0
0.50
0.75
1.00
2.85
0
0.2
0.4
0.6
0.8
1
LOAD CURRENT (A)
OUTPUT CURRENT (mA)
FIGURE 3. OUTPUT VOLTAGE vs OUTPUT CURRENT
FIGURE 4. GROUND CURRENT vs LOAD CURRENT
5.0
4.5
GROUND CURRENT (µA)
4.0
EN (2V/DIV)
3.5
3.0
VIN = 6V
2.5
SS (2V/DIV)
2.0
1.5
VOUT (5V/DIV)
1.0
0.5
0
-40
PG (5V/DIV)
-25
-10
5
20 35 50 65
TEMPERATURE (°C)
80
95
110 125
FIGURE 5. SHUTDOWN CURRENT vs TEMPERATURE
6
TIME (2ms/DIV)
FIGURE 6. ENABLE START-UP
FN7713.1
December 8, 2010
ISL80121-5
Typical Operating Performance
1.0
Unless otherwise noted: VIN = 5.4V, VOUT = 5.0V, CIN = COUT = 10µF,
TJ = +25°C, IL = 0A. (Continued)
RSET = 20kΩ
0.9
CURRENT LIMIT (A)
0.8
RSET = OPEN
0.7
0.6
VOUT (50V/DIV)
0.5
0.4
0.3
IOUT = 500mA
0.2
IOUT = 10mA
0.1
0
-40
10
60
110
TEMPERATURE (°C)
TIME (50µs/DIV)
FIGURE 7. CURRENT LIMIT vs TEMPERATURE
FIGURE 8. LOAD TRANSIENT RESPONSE
60
100mA LOAD
40
LOAD = 100mA
COUT = 100µF
50
MAGNITUDE (dB)
MAGNITUDE (dB)
1A LOAD
30
20
30
20
COUT = 22µF
10
0
10
COUT = 47µF
40
10
100
1k
10k
FREQUENCY (Hz)
100k
1M
FIGURE 9. PSRR vs LOAD
Functional Description
Input Voltage Requirements
The ISL80121-5 is optimized for 5V output, and can operate from
input voltages of 2.2V to 6V. Due to the nature of an LDO, VIN
must be some margin higher than VOUT plus dropout at the
maximum rated current of the application if active filtering
(PSRR) is expected from VIN to VOUT. The generous dropout
specification of this family of LDOs allows applications to design
for a level of efficiency that can accommodate profiles smaller
than the TO220/263.
Programmable Current Limit
0
10
COUT = 10µF
100
1k
10k
FREQUENCY (Hz)
100k
1M
FIGURE 10. PSRR vs C OUT
The current limit is set at 0.75A by default when the ISET pin is
left floating.
This limit can be increased by tying a resistor RSET from the ISET pin to
ground. The current limit is determined by RSET as shown in
Equation 1:
2.9
I LIMIT = 0.75 + -------------------------R SET ( kΩ )
(EQ. 1)
Figure 11 shows the relationship between RSET and the current
limit when the RSET is tied from ISET pin to GND. Do not short
this pin to ground. Increasing the current limit past 1.75A may
cause damage to the part and is highly discouraged.
The ISL80121-5 protects against overcurrent due to short-circuit
and overload conditions applied to the output. When this
happens, the LDO performs as a constant current source. If the
short-circuit or overload condition is removed, the output returns
to normal voltage regulation operation.
7
FN7713.1
December 8, 2010
ISL80121-5
source greater than VIN. PGOOD goes low when the output voltage
drops below 84% of the nominal output voltage, the current limit
faults, or the input voltage is too low. PGOOD functions during
shutdown, but not during thermal shutdown. For applications not
using this feature, connect this pin to ground.
CURRENT LIMIT (A)
1.7
1.5
Soft-Start Operation
1.3
1.1
0.9
0.7
2
20
RSET (kΩ)
200
FIGURE 11. INCREASING ILIMIT (R SET TO GND)
The soft-start circuit controls the rate at which the output voltage
rises up to regulation at power-up or LDO enable. This start-up
ramp time can be set by adding an external capacitor from the
SS pin to ground. An internal 2µA current source charges up this
CSS and the feedback reference voltage is clamped to the
voltage across it. The start-up time is set by Equation 3:
( C SS x0.5 )
T start = --------------------------2μA
(EQ. 3)
The current limit can be decreased from the 0.75A default by
tying RSET from the ISET pin to VIN. The current limit is then
determined by both RSET and VIN following Equation 2:
Equation 4 determines the CSS required for a specific start-up
in-rush current, where VOUT is the output voltage, COUT is the
total capacitance on the output and IINRUSH is the desired in-rush
current.
2.9 × ( 2 × V IN – 1 )
I LIMIT = 0.75 – ----------------------------------------------R SET ( kΩ )
( V OUT xC OUT x2μA ) )
C SS = ----------------------------------------------------I INRUSH x0.5V
(EQ. 2)
Figure 12 shows the relationship between RSET and the current
limit when RSET is tied from the ISET pin to VIN for VIN = 5.4V.
The external capacitor is always discharged to ground at the
beginning of start-up or enabling.
External Capacitor Requirements
0.75
External capacitors are required for proper operation. Careful
attention must be paid to the layout guidelines and selection of
capacitor type and value to ensure optimal performance.
0.65
0.55
CURRENT LIMIT (A)
(EQ. 4)
OUTPUT CAPACITOR
0.45
0.35
0.25
0.15
0.05
-0.05
40
RSET (kΩ)
400
FIGURE 12. DECREASING ISET (R SET TO VIN)
Enable Operation
The Enable turn-on threshold is typically 800mV with 80mV of
hysteresis. An internal pull-up or pull-down resistor to change
these values is available upon request. As a result, this pin must
not be left floating, and should be tied to VIN if not used. A 1kΩ to
10kΩ pull-up resistor is required for applications that use open
collector or open drain outputs to control the Enable pin. The
Enable pin may be connected directly to VIN for applications with
outputs that are always on.
The ISL80121-5 applies state-of-the-art internal compensation to
keep the selection of the output capacitor simple for the
customer. Stable operation over full temperature, VIN range,
VOUT range and load extremes are guaranteed for all capacitor
types and values assuming a minimum of 10µF X5R/X7R is used
for local bypass on VOUT. This output capacitor must be
connected to the VOUT and GND pins of the LDO with PCB traces
no longer than 0.5cm.
There is a growing trend to use very-low ESR multilayer ceramic
capacitors (MLCC) because they can support fast load transients and
also bypass very high frequency noise from other sources. However,
the effective capacitance of MLCCs drops with applied voltage, age,
and temperature. X7R and X5R dieletric ceramic capacitors are
strongly recommended as they typically maintain a capacitance
range within ±20% of nominal voltage over full operating ratings of
temperature and voltage.
Additional capacitors of any value in ceramic, POSCAP,
alum/tantalum electrolytic types may be placed in parallel to
improve PSRR at higher frequencies and/or load transient AC
output voltage tolerances.
Power-Good Operation
INPUT CAPACITOR
PGOOD is a logic output that indicates the status of VOUT, current
limit tripping, and VIN. The PGOOD flag is an open-drain NMOS
that can sink up to 10mA during a fault condition. The PGOOD
pin requires an external pull-up resistor typically connected to the
VOUT pin. The PGOOD pin should not be pulled up to a voltage
For proper operation, a minimum capacitance of 10µF X5R/X7R
is required at the input. This ceramic input capacitor must be
connected to the VIN and GND pins of the LDO with PCB traces
no longer than 0.5cm.
8
FN7713.1
December 8, 2010
ISL80121-5
Power Dissipation and Thermals
The junction temperature must not exceed the range specified in
the “Recommended Operating Conditions” on page 4. The power
dissipation can be calculated by using Equation 5:
P D = ( V IN – V OUT ) × I OUT + V IN × I GND
The DFN package uses the copper area on the PCB as a heat-sink.
The EPAD of this package must be soldered to the copper plane
(GND plane). Figure 13 shows a curve for the θJA of the DFN
package for different copper area sizes.
46
(EQ. 5)
(EQ. 6)
P D ( MAX ) = ( T J ( MAX ) – T A ) ⁄ θ JA
θJA is the junction-to-ambient thermal resistance.
For safe operation, enure that the power dissipation PD,
calculated from Equation 5, is less than the maximum allowable
power dissipation PD(MAX).
θJA (°C/W)
44
The maximum allowable junction temperature, TJ(MAX) and the
maximum expected ambient temperature, TA(MAX) determine the
maximum allowable power dissipation, as shown in Equation 6:
42
40
38
36
34
2
4
6
8
10
12
14
16
18
20
22
24
EPAD-MOUNT COPPER LAND AREA ON PCB, mm2
FIGURE 13. 3mmx3mm 10 LD DFN ON 4-LAYER PCB WITH THERMAL
VIAS θJA vs EPAD-MOUNT COPPER LAND AREA ON PCB
Thermal Fault Protection
The power level and the thermal impedance of the package
(+48°C/W for DFN) determine when the junction temperature
exceeds the thermal shutdown temperature. In the event that the die
temperature exceeds around +160°C, the output of the LDO will
shut down until the die temperature cools down to about +130°C.
9
FN7713.1
December 8, 2010
ISL80121-5
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make
sure you have the latest revision.
DATE
REVISION
CHANGE
12/6/10
FN7713.1
1. In “Block Diagram” on page 2:
a. Added "ADJ adjustable voltage version" Pin. Added "fixed voltage version" to "SENSE" pin
2. On page 4: “Ground Pin Current” Test Conditions
a. Replaced "VOUT+0.4V" with "2.2V" on both lines
12/2/10
FN7713.0
Initial Release.
Products
Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products
address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks.
Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a
complete list of Intersil product families.
*For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information page
on intersil.com: ISL80121-5
To report errors or suggestions for this datasheet, please go to: www.intersil.com/askourstaff
FITs are available from our website at: http://rel.intersil.com/reports/sear
For additional products, see www.intersil.com/product_tree
Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted
in the quality certifications found at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time
without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be
accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third
parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
10
FN7713.1
December 8, 2010
ISL80121-5
Package Outline Drawing
L10.3x3
10 LEAD DUAL FLAT PACKAGE (DFN)
Rev 6, 09/09
3.00
6
PIN #1 INDEX AREA
A
B
1
6
PIN 1
INDEX AREA
(4X)
3.00
2.00
8x 0.50
2
10 x 0.23
4
0.10
1.60
TOP VIEW
10x 0.35
BOTTOM VIEW
4
(4X)
0.10 M C A B
0.415
PACKAGE
OUTLINE
0.200
0.23
0.35
(10 x 0.55)
SEE DETAIL "X"
(10x 0.23)
1.00
MAX
0.10 C
BASE PLANE
2.00
0.20
C
SEATING PLANE
0.08 C
SIDE VIEW
(8x 0.50)
C
0.20 REF
5
1.60
0.05
TYPICAL RECOMMENDED LAND PATTERN
DETAIL "X"
NOTES:
1.
Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2.
Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3.
Unless otherwise specified, tolerance : Decimal ± 0.05
4.
Lead width applies to the metallized terminal and is measured
between 0.18mm and 0.30mm from the terminal tip.
5.
Tiebar shown (if present) is a non-functional feature.
6.
The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 indentifier may be
either a mold or mark feature.
11
FN7713.1
December 8, 2010