REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED R. MONNIN A Changes to input bias current and input offset current test conditions. Delete vendor CAGE 64762. Update boilerplate. –lgt 97-10-15 B Replaced reference to MIL-STD-973 with reference to MIL-PRF-38535. -rrp 04-01-27 R. MONNIN C Update drawing as part of 5 year review. - jt 11-01-18 C. SAFFLE THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY CHARLES E. BESORE STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http://www.dscc.dla.mil CHECKED BY RAY MONNIN APPROVED BY THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A MICHAEL A. FRYE DRAWING APPROVAL DATE MICROCIRCUIT, LINEAR, FOUR CHANNEL PROGRAMMABLE AMPLIFIER, MONOLITHIC SILICON 89-07-20 REVISION LEVEL C SIZE CAGE CODE A 67268 SHEET DSCC FORM 2233 APR 97 5962-87783 1 OF 11 5962-E145-11 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-87783 01 E X Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type. The device type identify the circuit function as follows: Device type Generic number 01 Circuit function HA-2400 Four channel programmable amplifier 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter E 2 Descriptive designator GDIP1-T16 or CDIP2-T16 CQCC1-N20 Terminals Package style 16 20 Dual-in-line Square leadless chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Voltage between +VCC and –VCC terminals ............................................................... Differential input voltage ............................................................................................ Output current (short-circuit protected) ..................................................................... Storage temperature range ....................................................................................... Internal power dissipation (PD) .................................................................................. Lead temperature (soldering, 10 seconds) ................................................................ Thermal resistance, junction-to-case (θJC): Cases E and 2 ....................................................................................................... Thermal resistance, junction-to-ambient (θJA): Case E ................................................................................................................... Case 2 ................................................................................................................... Junction temperature (TJ) .......................................................................................... +45 V dc ±VCC ±33 mA -65°C to +150°C 400 mW +275°C See MIL-STD-1835 91°C/W 88°C/W +175°C 1.4 Recommended operating conditions. Positive supply voltage (+VCC) .................................................................................. +15 V dc Negative supply voltage (-VCC) .................................................................................. -15 V dc Ambient operating temperature range (TA) ............................................................... -55°C to +125°C STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87783 A REVISION LEVEL C SHEET 2 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 MIL-STD-1835 - Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 MIL-HDBK-780 - List of Standard Microcircuit Drawings. Standard Microcircuit Drawings. (Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for nonJAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MILPRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MILPRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87783 A REVISION LEVEL C SHEET 3 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55°C ≤ TA ≤ +125°C unless otherwise specified VIO VCM = 0 V Group A subgroups Device type 1 01 Limits Min Input offset voltage +IIB 1 VCM = 0 V, +RS = 10 kΩ, -RS = 100 Ω -IIB VCM = 0 V, +RS = 100 Ω, -RS = 10 kΩ Input offset current IIO -RS = 10 kΩ Common mode input voltage range Large signal voltage gain +VCM +VCC = 6.0 V, -VCC = -24 V, VOUT = -9.0 V -VCM +VCC = +24 V, -VCC = -6.0 V, VOUT = 9.0 V AV VOUT = -10 V to +10 V, Output voltage swing +CMRR ∆VCM = +5.0 V, +VCC = +10 V, -VCC = -20 V, VOUT = -5.0 V -CMRR ∆VCM = +5.0 V, +VCC = +20 V, -VCC = -10 V, VOUT = 5.0 V +VOUT RL = 2 kΩ ±400 1 ±200 2, 3 ±400 ±50 01 1, 2, 3 01 +IOUT nA nA 9.0 V -9.0 4 01 50 5, 6 kV/V 25 1, 2, 3 01 80 dB 80 4, 5, 6 01 10 -VOUT Output current mV ±100 2, 3 RL = 2 kΩ Common mode rejection ratio ±200 01 2, 3 1 VCM = 0 V, +RS = 10 kΩ, Max ±9.0 ±11 2, 3 Input bias current Unit V -10 VOUT = 10 V, 4 01 10 mA TA = +25°C -IOUT -10 VOUT = -10 V, TA = +25°C Supply current +ICC VOUT = 0 V 1 +ICC 01 6.0 2, 3 7.0 1 -6.0 2, 3 -7.0 mA See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87783 A REVISION LEVEL C SHEET 4 TABLE I. Electrical performance characteristics – Continued. Symbol Conditions 1/ -55°C ≤ TA ≤ +125°C unless otherwise specified Group A subgroups Device type +PSRR1 +VCC = 20 V, -VCC = -15 V 1, 2, 3 01 +PSRR2 +VCC = 10 V, -VCC = -15 V 74 -PSRR1 +VCC = 15 V, -VCC = -20 V 74 -PSRR2 +VCC = 15 V, -VCC = -10 V 74 Crosstalk CT VIN = ±10 V, TA = +25°C Digital input current IIL VIL = 0 V IIH VIH = 5.0 V +SR1 VOUT = -5.0 V to +5.0 V, 7 AV = +1, RL = 2.0 kΩ, CL = 50 pF, CCOMP = 15 pF 8 5 VOUT = +5.0 V to -5.0 V, 7 6 AV = +1, RL = 2.0 kΩ, CL = 50 pF, CCOMP = 15 pF 8 5 VOUT = -5.0 V to +5.0 V, 7 AV = +10, RL = 2.0 kΩ, CL = 50 pF, CCOMP = 0 pF 8 17 VOUT = +5.0 V to -5.0 V, 7 20 AV = +10, RL = 2.0 kΩ, CL = 50 pF, CCOMP = 0 pF 8 17 VOUT = 0 to +200 mV, 7 AV = +1, RL = 2.0 kΩ, CL = 50 pF, CCOMP = 15 pF 8 55 VOUT = 0 to +200 mV, 2/ 7 45 AV = +10, RL = 2.0 kΩ, CL = 50 pF, CCOMP = 0 pF 8 55 VOUT = 0 to -200 mV, 7 AV = +1, RL = 2.0 kΩ, CL = 50 pF, CCOMP = 15 pF 8 55 VOUT = 0 to -200 mV, 7 45 AV = +10, RL = 2.0 kΩ, CL = 50 pF, CCOMP = 0 pF 8 55 Test Power supply rejection ratio Slew rate -SR1 Slew rate 2/ +SR2 -SR2 Rise time tr1 tr2 Fall time tf1 tf2 1 01 1, 2, 3 01 Limits Min 74 Unit Max dB -80 01 dB 1.5 mA 1.0 µA 6 01 V/µs 20 01 V/µs 45 01 ns 45 ns See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87783 A REVISION LEVEL C SHEET 5 TABLE I. Electrical performance characteristics – Continued. Test Conditions 1/ -55°C ≤ TA ≤ +125°C unless otherwise specified Group A subgroups Device type VOUT = 0 to +200 mV, 7 01 AV = +1, RL = 2.0 kΩ, CL = 50 pF, CCOMP = 15 pF 8 50 VOUT = 0 to -200 mV, 7 40 AV = +1, RL = 2.0 kΩ, CL = 50 pF, CCOMP = 15 pF 8 50 VOUT = 0 to +200 mV, 7 40 AV = +10, RL = 2.0 kΩ, CL = 50 pF, CCOMP = 0 pF 2/ 8 50 VOUT = 0 to -200 mV, 7 40 AV = +10, RL = 2.0 kΩ, CL = 50 pF, CCOMP = 0 pF 2/ 8 50 UGBW AV = +1, RL = 2.0 kΩ, CL = 50 pF, CCOMP = 15 pF, 4 01 4 MHz GBWP AV = +10, RL = 2.0 kΩ, CL = 50 pF, CCOMP = 0 pF, 4 01 20 MHz 4 01 95 kHz Symbol Limits Min Overshoot +OS1 -OS1 +OS2 -OS2 Unity gain bandwidth 2/ Unit Max 40 % TA = +25°C Gain bandwidth product 2/ TA = +25°C Full power bandwidth 2/ 3/ FPBW 1 VO = ±10 V, AV = +1, RL = 2.0 kΩ, CL = 50 pF, CCOMP = 15 pF FPBW 2 VO = ±10 V, AV = +10, RL = 2.0 kΩ, CL = 50 pF, CCOMP = 0 pF 5, 6 79 4 300 5, 6 270 See footnotes at end of table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87783 A REVISION LEVEL C SHEET 6 TABLE I. Electrical performance characteristics – Continued. Test Symbol Conditions 1/ -55°C ≤ TA ≤ +125°C unless otherwise specified Group A subgroups Device type Limits 7 01 Max 2.5 µs 9 01 250 ns Min Settling time 2/ tS VENABLE = +5.0 V (or Decode Control), AV = +1, CCOMP = 15 pF, Unit RL = 2.0 kΩ, CL = 50 pF, VO = 10 VP-P to 0.1% final value, TA = +25°C Output delay 2/ td 50% of Enable (or Decode Control) to 10% of output, VENABLE = +5.0 V (or Decode Control), TA = +25°C 1/ +VCC = +15 V, -VCC = -15 V, RS = 100 Ω, RL = 500 kΩ, and VOUT = 0 V, unless otherwise specified. Digital inputs: VIL = +0.5 and VIH = +2.4 V. Limits apply to each of the four channels, when addressed. See figure 2 herein. 2/ Parameters shall be characterized at initial device design and after major process or design change which affects these parameters. Sample size = 15 minimum. 3/ Full power bandwidth = SR . 2πV(pk) 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that affects this drawing. 3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime 's agent, and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87783 A REVISION LEVEL C SHEET 7 Device type Case outlines Terminal number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 01 E 2 Terminal symbol Input 3+ No connection Input 3Input 3+ Input 4+ Input 3Input 4Input 4+ Input 1Input 4Input 1+ No connection Input 2Input 1Input 2+ Input 1+ -VCC Input 2Output Input 2+ +VCC No connection COMP -VCC Ground Output ENABLE +VCC D1 COMP D0 No connection ---Ground ---ENABLE ---D1 ---D0 FIGURE 1. Terminal connections. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87783 A REVISION LEVEL C SHEET 8 D1 D0 ENABLE L L H H X L H L H X H H H H L Selected channel 1 2 3 4 None FIGURE 2. Truth table. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87783 A REVISION LEVEL C SHEET 9 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA = +125°C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 10, 11 in table I, method 5005 of MIL-STD-883 shall be omitted. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA = +125°C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87783 A REVISION LEVEL C SHEET 10 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Interim electrical parameters (method 5004) Final electrical test parameters (method 5004) Group A test requirements (method 5005) Groups C and D end-point electrical parameters (method 5005) Subgroups (in accordance with MIL-STD-883, method 5005, table I) --1*, 2, 3, 4, 5, 6, 7 1, 2, 3, 4, 5, 6, 7, 8**, 9 1 * PDA applies to subgroup 1. ** Subgroup 8 is guaranteed if not tested. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DLA Land and Maritime -VA, telephone (614) 692-0547. 6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime -VA, Columbus, Ohio 432183990, or telephone (614) 692-0540. 6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MILHDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by DLA Land and Maritime -VA. STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE 5962-87783 A REVISION LEVEL C SHEET 11 STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 11-01-18 Approved sources of supply for SMD 5962-87783 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime maintains an online database of all current sources of supply at http://www.dscc.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ 5962-8778301EA 5962-87783012A Vendor CAGE number 34371 3/ Vendor similar PIN 2/ HA1-2400/883 HA4-2400/883 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3/ Not available from an approved source of supply. Vendor CAGE number 34371 Vendor name and address Intersil Corporation 1001 Murphy Ranch Road Milpitas, CA 95035-6803 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin.