DATASHEET

REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
A
In accordance with N.O.R. 5962-R111-93
93-03-30
M. A. FRYE
B
Drawing updated to reflect current requirements. -ro
01-02-12
R. MONNIN
C
Update drawing as part of 5 year review. -rrp
07-02-27
J. RODENBECK
D
Update drawing to current MIL-PRF-38535 requirements. -jt
13-04-03
C. SAFFLE
THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
REV
D
D
D
D
D
D
D
D
D
D
D
OF SHEETS
SHEET
1
2
3
4
5
6
7
8
9
10
11
PMIC N/A
PREPARED BY
RICK C. OFFICER
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil
CHECKED BY
CHARLES E. BESORE
APPROVED BY
MICHAEL A. FRYE
DRAWING APPROVAL DATE
92-11-03
REVISION LEVEL
D
MICROCIRCUIT, LINEAR, HIGH SPEED,
OPERATIONAL AMPLIFIER, MONOLITHIC
SILICON
SIZE
CAGE CODE
A
67268
SHEET
DSCC FORM 2233
APR 97
5962-89880
1 OF 11
5962-E174-13
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-89880
01
P
A
Drawing number
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
Lead finish
(see 1.2.3)
1.2.1 Device types. The device types identify the circuit function as follows:
Device type
Generic number
01
02
Circuit function
HA-2522
HA-2520
High speed operational amplifier
High speed operational amplifier
1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows:
Outline letter
G
P
2
Descriptive designator
MACY1-X8
GDIP1-T8 or CDIP2-T8
CQCC1-N20
Terminals
Package style
8
8
20
Can
Dual-in-line
Square leadless chip carrier
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings.
Voltage between +VS and –VS pins .....................................
Differential input voltage ......................................................
Voltage at either input pin ...................................................
Peak output current .............................................................
Power dissipation (PD): 1/
Case G ............................................................................
Case P .............................................................................
Case 2 .............................................................................
Junction temperature (TJ) ...................................................
Storage temperature range .................................................
Lead temperature (soldering, 10 seconds) ..........................
Thermal resistance, junction-to-case (θJC) .........................
40 V dc
15 V dc
+VS to –VS
50 mA
670 mW
710 mW
1.3 W
+175°C
-65°C to +150°C
+275°C
See MIL-STD-1835
Thermal resistance, junction-to-ambient (θJA):
Case G ............................................................................ +148°C/W
Case P ............................................................................. +140°C/W
Case 2 ............................................................................. +76°C/W
1/
Power dissipation derating factor above TA = +75°C for case G is 6.7 mW/°C, case P is 7.1 mW/°C, and
for case 2 is 13.1 mW/°C.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-89880
A
REVISION LEVEL
D
SHEET
2
1.4 Recommended operating conditions.
Operating supply voltage ..................................................... ±15 V dc
Common mode voltage (VCM) ............................................ ≤ |1/2 (+VS – (-VS))|
Load resistance (RL) ........................................................... ≥ 2 kΩ
Source resistance (RS) ....................................................... 50 Ω
Ambient operating temperature range (TA) ......................... -55°C to +125°C
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 MIL-STD-1835 -
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Copies of these documents are available online at https://assist.dla.mil/quicksearch/ or from the Standardization Document
Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for nonJAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MILPRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MILPRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outlines. The case outline shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure1.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-89880
A
REVISION LEVEL
D
SHEET
3
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions
-55°C ≤ TA ≤ +125°C
+VS = +15 V, -VS = -15 V
Group A
subgroups
Device
type
1
01
unless otherwise specified
Input offset voltage
VIO
VCM = 0 V 2/
2,3
1
02
2,3
Input bias current
+IB
1
VCM = 0 V, 2/
01
2,3
RS = 10 kΩ
1
02
2,3
-IB
1
VCM = 0 V, 2/
01
2,3
RS = 10 kΩ
1
02
2,3
Input offset current
IIO
1
VCM = 0 V, 2/
01
2,3
RS = 10 kΩ
1
02
2,3
Common mode voltage
range
+VCMR
1,2,3
+VS = +5 V, 2/
01,02
Limits 1/
Unit
Min
-10
Max
+10
-14
+14
-8
+8
-10
+10
-250
+250
-500
+500
-200
+200
-400
+400
-250
+250
-500
+500
-200
+200
-400
+400
-50
+50
-100
+100
-25
+25
-50
+50
+10
mV
nA
nA
V
-VS = -25 V
-VCMR
-10
+VS = +25 V, 2/
-VS = -5 V
Large signal voltage
gain
+AVOL
4
VOUT = 0 V and +10 V, 2/
01
7.5
5,6
RL = 2 kΩ
4
kV/V
5
02
10
5,6
7.5
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-89880
A
REVISION LEVEL
D
SHEET
4
TABLE I. Electrical performance characteristics – Continued.
Test
Symbol
Conditions
-55°C ≤ TA ≤ +125°C
+VS = +15 V, -VS = -15 V
Group A
subgroups
Device
type
4
01
unless otherwise specified
Large signal voltage
gain
-AVOL
VOUT = 0 V and -10 V, 2/
Min
7.5
5,6
RL = 2 kΩ
4
+CMRR
4,5,6
02
kV/V
7.5
74
02
80
∆VCM = -10 V, 2/
01
74
+VS = +25 V, -VS = -5 V,
02
80
01,02
+10
+VS = +5 V, -VS = -25 V,
Max
10
01
∆VCM = +10 V, 2/
Unit
5
5,6
Common mode rejection
ratio
Limits 1/
dB
VOUT = -10 V
-CMRR
VOUT = +10 V
Output voltage swing
+VOUT
4,5,6
RL = 2 kΩ 2/
-10
-VOUT
Output current
+IOUT
4
VOUT = -10 V 2/
01,02
5,6
-IOUT
Quiescent power supply
current
+ICC
V
VOUT = +10 V 2/
+7.5
-10
5,6
-7.5
01
6
5,6
IOUT = 0 mA
4
4
02
6
6.5
01
-6
5,6
4
mA
7
5,6
-ICC
mA
4
4
VOUT = 0 V 2/
+10
-7
02
-6
5,6
-6.5
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-89880
A
REVISION LEVEL
D
SHEET
5
TABLE I. Electrical performance characteristics – Continued.
Test
Symbol
Conditions
-55°C ≤ TA ≤ +125°C
Group A
subgroups
Device
type
1,2,3
01
Min
74
02
80
∆VS = 10 V,
01
74
+VS = +15 V, -VS = -20 V,
02
80
01,02
VIO
+VS = +15 V, -VS = -15 V
unless otherwise specified
Power supply rejection
ratio
+PSRR
∆VS = 10 V,
+VS = +20 V, -VS = -15 V,
Limits 1/
Unit
Max
dB
+VS = +10 V, -VS = -15 V
-PSRR
+VS = +15 V, -VS = -10 V
Offset voltage adjustment
Slew rate
+VIO
2/ 3/
1,2,3
Adj
–1
-VIO
VIO
Adj
+1
+SR
VOUT = -5 V to +5 V, 4/
7
01
measured from –2.5 V to
+2.5 V
8A,8B
7
80
02
VOUT = +5 V to -5 V, 4/
7
measured from +2.5 V to
-2.5 V
8A,8B
100
84
01
7
80
60
02
100
8A,8B
Rise and fall time
TR
9
VOUT = 0 V to +200 mV 4/
84
01
50
10,11
10 % ≤ TR ≤ 90 %
9
9
VOUT = 0 V to -200 mV 4/
02
50
55
01
50
10,11
10 % ≤ TF ≤ 90 %
9
ns
60
10,11
TF
V/µs
60
8A,8B
-SR
mV
60
02
50
10,11
55
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-89880
A
REVISION LEVEL
D
SHEET
6
TABLE I. Electrical performance characteristics – Continued.
Test
Symbol
Conditions
-55°C ≤ TA ≤ +125°C
+VS = +15 V, -VS = -15 V
Group A
subgroups
Device
type
9
01
unless otherwise specified
Overshoot
+OS
Limits 1/
Min
VOUT = 0 V to +200 mV 4/
10,11
9
9
VOUT = 0 V to -200 mV 4/
02
45
01
50
60
02
40
10,11
Differential input
resistance
RIN
1
VCM = 0 V, 5/ 6/
TA = +25°C
Gain bandwidth product
GBWP
Measured at 10 kHz, 5/ 6/
4
%
40
10,11
9
Max
50
60
10,11
-OS
Unit
45
01
40
02
50
01,02
10
MΩ
MHz
VOUT = 200 mV,
TA = +25°C
Measured at 1 MHz, 5/ 6/
10
VOUT = 200 mV,
TA = +25°C
Full power bandwidth
FPBW
4
VPEAK = 10 V, 5/ 6/ 7/
TA = +25°C
01
1.2
02
1.6
3
MHz
Closed loop stable
gain
CLSG
5/ 6/
4,5,6
01,02
Quiescent power
consumption
PC
VOUT = 0 V, 5/ 6/ 8/
1,2,3
01
210
02
195
01,02
1.1
IOUT = 0 mA, TA = +25°C
Settling time
tS
10 V step at 0.1% of the
9
V/V
mW
µs
fixed value, TA = +25°C
5/ 6/
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-89880
A
REVISION LEVEL
D
SHEET
7
1/
The algebraic convention, whereby the most negative value is a minimum and the most positive is a maximum,
is used in this table. Negative current shall be defined as conventional current flow out of a device terminal.
2/
Unless otherwise specified, RS = 100 Ω, RL = 500 kΩ, and VOUT = 0 V.
3/
Offset adjustment range is (VIO is measured at ±1 mV) minimum referred to output. This test is for functionality only
to assure adjustable through 0 V.
4/
Unless otherwise specified, RS = 50 Ω, RL = 2 kΩ, CL = 50 pF, and AVCL = +3 V/V.
5/
Unless otherwise specified, RL = 2 kΩ, CL = 50 pF, AV ≥ 3, and CCOMP = 0 pF.
6/
If not tested, shall be guaranteed to the limits specified in table I herein.
7/
Full power bandwidth is guaranteed by the slew rate measurement using the following equation;
FPBW = slew rate / ( 2π x VPEAK).
8/
Quiescent power consumption is guaranteed by the quiescent supply current test. No load on outputs.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD
PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and
Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the
requirements of MIL-PRF-38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that
affects this drawing.
3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime's agent, and the acquiring activity retain the
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-89880
A
REVISION LEVEL
D
SHEET
8
Device types
01 and 02
Case outlines
G and P
2
Terminal
number
1
Terminal symbol
BALANCE (BAL)
NC
2
-INPUT
BALANCE (BAL)
3
+INPUT
NC
4
-VS
NC
5
BALANCE (BAL)
-INPUT
6
OUTPUT
NC
7
+VS
+INPUT
8
COMPENSATION (COMP)
NC
9
---
NC
10
---
-VS
11
---
NC
12
---
BALANCE (BAL)
13
---
NC
14
---
NC
15
---
OUTPUT
16
---
NC
17
---
+VS
18
---
NC
19
---
NC
20
---
COMPENSATION (COMP)
NC = No connection
FIGURE 1. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-89880
A
REVISION LEVEL
D
SHEET
9
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,
appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices
prior to quality conformance inspection. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify
the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method
1015 of MIL-STD-883.
(2) TA = +125°C, minimum.
b.
Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD883 including groups A, B, C, and D inspections. The following additional criteria shall apply.
4.3.1 Group A inspection.
a.
Tests shall be as specified in table II herein.
4.3.2 Groups C and D inspections.
a.
End-point electrical parameters shall be as specified in table II herein.
b.
Steady-state life test conditions, method 1005 of MIL-STD-883.
(1)
Test condition A, B, C or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1005 of MIL-STD-883.
(2)
TA = +125°C, minimum.
(3)
Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-89880
A
REVISION LEVEL
D
SHEET
10
TABLE II. Electrical test requirements.
MIL-STD-883 test requirements
Interim electrical parameters
(method 5004)
Final electrical test parameters
(method 5004)
Group A test requirements
(method 5005)
Groups C and D end-point
electrical parameters
(method 5005)
Subgroups
(in accordance with
MIL-STD-883, method 5005,
table I)
--1*,2,3,4,5,6,7,8
1,2,3,4,5,6,7,8,9**,10**,11**
1
* PDA applies to subgroup 1.
** Subgroups 9, 10, and 11, if not tested, shall be guaranteed to the limits
specified in table I.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires
configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this
list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics
devices (FSC 5962) should contact DLA Land and Maritime -VA, telephone (614) 692-8108.
6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime -VA, Columbus, Ohio 432183990, or telephone (614) 692-0540.
6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103 and QML-38535. The vendors
listed in MIL-HDBK-103 and QML-38535 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been
submitted to and accepted by DLA Land and Maritime -VA.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-89880
A
REVISION LEVEL
D
SHEET
11
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 13-04-03
Approved sources of supply for SMD 5962-89880 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information
bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime
maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Reference
military specification
PIN
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-8988001GC
3/
HA2-2522/883
5962-8988001PA
3/
HA7-2522/883
5962-89880012A
3/
HA4-2522/883
5962-8988002GC
34371
HA2-2520/883
M38510/12206BGA
5962-8988002PA
3/
HA7-2520/883
M38510/12206BPA
5962-89880022A
3/
HA4-2520/883
M38510/12206BPA
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed contact the vendor
to determine its availability.
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number may not
satisfy the performance requirements of this drawing.
3/ Not available from an approved source of supply.
Vendor CAGE
number
34371
Vendor name
and address
Intersil Corporation
1001 Murphy Ranch Road
Milpitas, CA 95035-6803
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.