86879

REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
A
Make changes to paragraphs 1.3, 4.3.1c, table I, and figure 3. Make editorial
changes throughout.
89-01-30
M. A. Frye
B
Add one vendor, CAGE 07933. Make changes to table I and editorial changes
throughout. Remove vendor CAGE 34371. Device 013X is not available from
an approved source of supply.
90-05-30
M. A. Frye
C
Changes in accordance with N.O.R. 5962-R013-91.
91-09-27
M. A. Frye
D
Drawing updated to reflect current requirements. - ro
02-07-08
R. Monnin
E
Redrawn. Update paragraphs to MIL-PRF-38535 requirements. - drw
14-10-09
Charles F. Saffle
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
REV
E
E
E
E
E
E
E
E
E
E
E
OF SHEETS
SHEET
1
2
3
4
5
6
7
8
9
10
11
PMIC N/A
PREPARED BY
Donald R. Osborne
STANDARD
MICROCIRCUIT
DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil
CHECKED BY
Ray Monnin
APPROVED BY
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
Michael A. Frye
DRAWING APPROVAL DATE
MICROCIRCUIT, LINEAR, BUS INTERFACE
DRIVER CIRCUIT, MONOLITHIC SILICON
88-05-05
REVISION LEVEL
E
SIZE
CAGE CODE
A
67268
SHEET
DSCC FORM 2233
APR 97
5962-86879
1 OF 11
5962-E007-15
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-86879
01
E
A
Drawing number
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
Lead finish
(see 1.2.3)
1.2.1 Device type. The device type identifies the circuit function as follows:
Device type
Generic number
01
Circuit function
HS-3182, HI-8382
Bus interface line driver circuit
1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 as follows:
Outline letter
E
3
Descriptive designator
Terminals
GDIP1-T16 or CDIP2-T16
CQCC1-N28
16
28
Package style
Dual-in-line
Square leadless chip carrier
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings.
V+ minus V- (differential voltage) ...................................................... 40 V dc
V1 ..................................................................................................... 7 V dc
VREF ................................................................................................. 6 V dc
Logic input voltage range .................................................................. (GND - 0.3 V) to (V1 + 0.3 V)
Maximum power dissipation (PD):
Case E ..........................................................................................
Case 3 ...........................................................................................
Junction temperature (TJ) .................................................................
Lead temperature (soldering, 10 seconds) .......................................
Storage temperature range ...............................................................
Thermal resistance, junction-to-case (θJC) .......................................
1.725 W 1/
1.12 W 1/
+175°C
+275°C
-65°C to +150°C
See MIL-STD-1835
Thermal resistance, junction-to-ambient (θJA):
Case E .......................................................................................... 86.5°C/W
Case 3 ........................................................................................... 133.7°C/W
_____
1/ Derate above +25°C, 11.5 mW/°C for case E, and 7.5 mW/°C for case 3.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-86879
A
REVISION LEVEL
E
SHEET
2
1.4 Recommended operating conditions. 2/
Supply voltage:
V+ ................................................................................................ 15 V dc ±10%
V- ................................................................................................ -15 V dc ±10%
V1 ................................................................................................ 5 V dc ±5%
VREF .............................................................................................. 5 V dc ±5%
Ambient operating temperature range (TA) ....................................... -55°C to +125°C
Maximum load:
Data rate at 12.5 KBPS: RL = 800Ω, CL = 30 nF; RL = 400Ω, CL = 6.9 nF.
Data rate at 100 KBPS: RL = 800Ω, CL = 4 nF.
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 MIL-STD-1835 -
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 MIL-HDBK-780 -
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Copies of these documents are available online at http://quicksearch.dla.mil or from the Standardization Document Order
Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
_____
2/ All voltages referenced to GND.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-86879
A
REVISION LEVEL
E
SHEET
3
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for nonJAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to
MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and
qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management
(QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the
device. These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with
MIL-PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Truth table. The truth table shall be as specified on figure 2.
3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD
PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DLA Land and
Maritime -VA prior to listing as an approved source of supply shall affirm that the manufacturer's product meets the
requirements of MIL-PRF-38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DLA Land and Maritime -VA shall be required for any change that
affects this drawing.
3.9 Verification and review. DLA Land and Maritime, DLA Land and Maritime's agent, and the acquiring activity retain the
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-86879
A
REVISION LEVEL
E
SHEET
4
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions
-55°C ≤ TA ≤ +125°C
unless otherwise specified
Group A
subgroups
Device
type
Limits
Min
Unit
Max
Supply current V+
(operating)
ICCOP
(V+)
No load (0-100 k bits/s)
1, 2, 3
01
16
mA
Supply current V(operating)
ICCOP
(V-)
No load (0-100 k bits/s)
1, 2, 3
01
-16
mA
Supply current V1
(operating)
ICCOP
No load (0-100 k bits/s)
1, 2, 3
01
975
µA
Supply current VREF
(operating)
ICCOP
No load (0-100 k bits/s)
1, 2, 3
01
-1.0
mA
(V1)
(VREF)
Supply current V(during short circuit test)
ISC
(V-)
Short to ground 1/
1, 2, 3
01
-150
mA
Supply current V+
(during short circuit test)
ISC
(V+)
Short to ground 1/
1, 2, 3
01
150
mA
Output short circuit
current (output high)
IOSHC
Short to ground, Vmin = 0 V
2/
1, 2, 3
01
-80
mA
Output short circuit
current (output low)
IOSLC
Short to ground, Vmin = 0 V
2/
1, 2, 3
01
+80
mA
Input current (input high)
IIH
1, 2, 3
01
10
µA
Input current (input low)
IIL
1, 2, 3
01
-20
µA
Output voltage high
(output to ground)
VOH
No load (0-100 k bits/s)
1, 2, 3
01
+VREF
- .25
+VREF
+ .25
V
Output voltage low
(output to ground)
VOL
No load (0-100 k bits/s)
1, 2, 3
01
-VREF
- .25
-VREF
+ .25
V
Output voltage null
VNULL
No load (0-100 k bits/s)
1, 2, 3
01
-250
+250
mV
Input capacitance
CIN
See 4.3.1c, TA = +25°C
4
01
30
pF
VIH = 2.0 V, VIL = 0.5 V,
see 4.3.1d 3/
7, 8
01
Functional tests
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-86879
A
REVISION LEVEL
E
SHEET
5
TABLE I. Electrical performance characteristics – continued.
Test
Symbol
Conditions
-55°C ≤ TA ≤ +125°C
unless otherwise specified
Group A
subgroups
Device
type
Limits
Unit
Min
Max
Rise time (AOUT, BOUT)
tr
See figure 4, CL = 75 pF
3/
9, 10, 11
01
0.9
2.4
µs
Fall time (AOUT, BOUT)
tf
See figure 4, CL = 75 pF
3/
9, 10, 11
01
0.9
2.4
µs
Propagation delay input
to output
tPLH
See figure 4, CL = 75 pF
3/
9, 10, 11
01
3.3
µs
Propagation delay input
to output
tPHL
See figure 4, CL = 75 pF
3/
9, 10, 11
01
3.3
µs
1/
Not tested, but characterized at initial device design and after major process or design change which affects this
parameter.
2/
Interchangeability of force and sense is acceptable.
3/
V+ = 15 V, V- = 15 V, V1 = VREF = 5.0 V.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-86879
A
REVISION LEVEL
E
SHEET
6
Device type
01
Case outlines
E
Terminal
number
3
Terminal symbol
1
VREF
VREF
2
GND
NC
3
SYNC
GND
4
DATA (A)
SYNC
5
CA
NC
6
AOUT
DATA (A)
7
-V
NC
8
GND
NC
9
+V
CA
10
NC
NC
11
BOUT
NC
12
CB
NC
13
DATA (B)
AOUT
14
CLOCK
-V
15
NC
GND
16
V1
+V
17
---
BOUT
18
---
NC
19
---
NC
20
---
NC
21
---
NC
22
---
CB
23
---
DATA (B)
24
---
NC
25
---
CLOCK
26
---
NC
27
---
NC
28
---
V1
NC = No connection
FIGURE 1. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-86879
A
REVISION LEVEL
E
SHEET
7
SYNC
CLOCK
DATA (A)
DATA (B)
AOUT
BOUT
COMMENTS
X
L
X
X
0V
0V
NULL
L
X
X
X
0V
0V
NULL
H
H
L
L
0V
0V
NULL
H
H
L
H
-VREF
+VREF
LOW
H
H
H
L
H
H
H
-VREF
0V
HIGH
H
+VREF
0V
NULL
FIGURE 2. Truth table.
FIGURE 3. Logic diagram.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-86879
A
REVISION LEVEL
E
SHEET
8
NOTE:
tr measured 50 percent to 90 percent times two.
tf measured 50 percent to 90 percent times two.
VIH = 2.0 V, VOL = -4.75 V to -5.25 V
VIL = 0.5 V, VOH = 4.75 V to 5.25 V
FIGURE 4. Switching waveforms.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-86879
A
REVISION LEVEL
E
SHEET
9
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,
appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices
prior to quality conformance inspection. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify
the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method
1015 of MIL-STD-883.
(2) TA = +125°C, minimum.
b.
Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
TABLE II. Electrical test requirements.
MIL-STD-883 test requirements
Interim electrical parameters
(method 5004)
Final electrical test parameters
(method 5004)
Group A test requirements
(method 5005)
Groups C and D end-point
electrical parameters
(method 5005)
Subgroups
(in accordance with
MIL-STD-883, method 5005,
table I)
--1*, 2, 3, 7, 8, 9
1, 2, 3, 4, 7, 8, 9, 10, 11
1, 2, 3
* PDA applies to subgroup 1.
4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of
MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply.
4.3.1 Group A inspection.
a.
Tests shall be as specified in table II herein.
b.
Subgroups 5 and 6 in table I, method 5005 of MIL-STD-883 shall be omitted.
c.
Subgroup 4 (CIN measurement) shall be measured only for the initial test and after process or design changes which
may affect input capacitance. Sample size is 15 devices, all input and output terminals tested, and no failures.
d.
Subgroups 7 and 8 shall include verification of the truth table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-86879
A
REVISION LEVEL
E
SHEET
10
4.3.2 Groups C and D inspections.
a.
End-point electrical parameters shall be as specified in table II herein.
b.
Steady-state life test conditions, method 1005 of MIL-STD-883.
(1)
Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1005 of MIL-STD-883.
(2)
TA = +125°C, minimum.
(3)
Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires
configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this
list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics
devices (FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-8108.
6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990,
or telephone (614) 692-0540.
6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103 and QML-38535. The vendors
listed in MIL-HDBK-103 and QML-38535 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been
submitted to and accepted by DLA Land and Maritime-VA.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-86879
A
REVISION LEVEL
E
SHEET
11
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 14-10-09
Approved sources of supply for SMD 5962-86879 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DLA Land and Maritime-VA. This information
bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DLA Land and Maritime
maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-8687901EA
34371
HS1-3182/883
44270
HI-8382CM-03
3/
HI-8382CM-02
3/
RM3182S/883B
3/
HI-8382SM-02
3/
HS4-3182/883
5962-86879013A
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed contact the vendor
to determine its availability.
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number may not
satisfy the performance requirements of this drawing.
3/ Not available from an approved source of supply.
Vendor CAGE
number
Vendor name
and address
34371
Intersil Corporation
1001 Murphy Ranch Road
Milpitas, CA 95035-6803
44270
Holt Integrated Circuits, Inc.
23351 Madero
Mission Viejo, CA 92691-2730
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.