Panasonic To No. A768-040403N-01 Date 3rd Apr. '04 Type No. CTDA1 Data Sheet CDMA800/GSM850 Tx SAW Filter Application : Tx Filter for CDMA800/GSM850 Center Frequency : 836.5MHz Size : 2.0x1.4mm, 5pin-layout Impedance : 50-50ohms unbalance-unbalance Part No. : EFCH836MTCD1 Issued Check S.Tsuzuki K,Nishimura CIRCUIT COMPONENTS BUSINESS UNIT MATSUSHITA ELECTRONIC COMPONENTS CO.,LTD KADOMA, OSAKA, JAPAN 2003.10.12 CDMA800/GSM850 Tx SAW Filter ----- Unbalanced input and output ----Part No. : Design No. : T836PD1 Parameter Frequency Your request Min. Passband Typ. Our preliminary spec. Max. Min. 824 ... 849 Typ. Unit Max. 824 ... 849 MHz Insertion loss 824 ... 849MHz 1.7 2.3 dB Ripple in passband 824 ... 849MHz 0.3 1.2 dB Attenuation VSWR Att1 DC ... 800MHz 40 58 dB Att2 869 ... 894MHz 27 32 dB Att3 1648 ... 1698MHz 35 52 dB Att4 2472 ... 2547MHz 30 50 dB Input 824 ... 849MHz 1.6 2.0 Output 824 ... 849MHz 1.6 2.0 Input impedance 50 Ohm Output impedance 50 Ohm Maximum drive level 10 dBm Operating temperature -30 +85 deg. C Storage temperature -40 +85 deg. C Panasonic 2003.10.12 CDMA800/GSM850 Tx SAW Filter ----- Unbalanced input and output ----Part No. : Design No. : T836PD1 Panasonic 2003.10.12 CDMA800/GSM850 Tx SAW Filter ----- Unbalanced input and output ----Part No. : Design No. : T836PD1 Panasonic UNLESS OTHERWISE SPECIFIED THIRD ANGLE PROJECTION BASIC DIMENSIONS Tolerance : +/-0.05 UP TO 2.0 +/- 0.15 TOLERANCE INCL TO INCL TO INCL TO INCL 0.8 +/- 0.15 1.4 +/- 0.15 ABOVE 2-0.735 ISSUE 5-0.38 (2) (1) Input (2) GND (3) GND (4) Output (5) GND (3) DO NOT SCALE DRAWING (4) 0.075 (5) REVISIONS INDICATED BY ∆ DATE SCALE DRAW CHECK APPROVAL DRAWING NO. NAME 0.075 REVISIONS FINISH DESIGN 5-0.44 (1) MATERIAL Note : The design manufacturing process, and Specification of this device are subject to change without notice. ALL DIMENSIONS ARE IN MILLIMETERS TYPE NO. SAW Filter CERAMIC BUSINESS UNIT, LCR DEVICE COMPANY MATSUSHITA ELECTRONIC COMPONENTS CO.,LTD. KADOMA, OSAKA, JAPAN THIRD ANGLE PROJECT ION UNLESS OTHERWISE SPECIFIED BASIC DIMENSIONS UP TO Measurement Circuit TOLERANCE INCL TO INCL TO INCL TO INCL ABOVE (2) (3) (1) S C (5) (4) D 0 Level ISSUE (2) S : Standard Signal Generator (Output Impedance 50ohm) C : Frequency Counter D : Detector (Input Impedance 50ohm) (3) (1) MATERIAL REVISIONS FINISH DATE SCAL E DESIGN DRAW CHECK S C (5) APPROVAL (4) DRAWING NO. D NAME TYPE NO. SAW Filter Fig. 2 DO NOT SCALE DRAWING REVISIONS INDICATED BY ALL DIMENSIONS ARE IN MILLIMETERS CERAMIC BUSINESS UNIT, LCR DEVICE COMPANY MATSUSHITA ELECTRONIC COMPONENTS CO.,LTD. KADOMA, OSAKA, JAPAN UNLESS OTHERWISE SPECIFIED THIRD ANGLE PROJECTION BASIC DIMENSIONS UP TO Recommended land pattern TOLERANCE INCL TO INCL TO INCL TO INCL ABOVE 0.255 0.255 0.810 0.270 5-0.540 5-0.480 ISSUE MATERIAL 0.735 REVISIONS FINISH DATE SCALE DESIGN 0.735 DRAW CHECK APPROVAL DRAWING NO. NAME Note : The design manufacturing process, and Specification of this device are subject to change without notice. DO NOT SCALE DRAWING REVISIONS INDICATED BY ∆ ALL DIMENSIONS ARE IN MILLIMETERS TYPE NO. SAW Filter CERAMIC BUSINESS UNIT, LCR DEVICE COMPANY MATSUSHITA ELECTRONIC COMPONENTS CO.,LTD. KADOMA, OSAKA, JAPAN