Panasonic To No. ZGSM-040403M-01 Date 3rd Apr. '04 Type No. ERDA2 Data Sheet EGSM900 Rx SAW Filter Application : Rx Filter for EGSM900 Center Frequency : 942.5MHz Size : 2.0x1.4mm, 5pin-layout Impedance : 50-50ohms unbalance-unbalance Part No. : EFCH942MTCD1 Issued Check A.Tsunekawa K,Nishimura CIRCUIT COMPONENTS BUSINESS UNIT MATSUSHITA ELECTRONIC COMPONENTS CO.,LTD KADOMA, OSAKA, JAPAN 2004.1.6 EGSM900 Rx SAW Filter ----- Unbalanced input and unbalanced output ----Part No. : Design No. : T942CL1 Parameter Frequency Your request Min. Passband Typ. Our Specification Max. Min. 925 ... 960 Typ. Unit Max. 925 ... 960 MHz Insertion loss 925 ... 960MHz 1.7 2.4 dB Ripple in passband 925 ... 960MHz 0.6 1.5 dB Attenuation VSWR Att1 DC ... 880MHz 30 60 dB Att2 880 ... 905MHz 23 32 dB Att3 905 ... 915MHz 18 21 dB Att4 980 ... 1500MHz 26 32 dB Att5 1500 ... 3000MHz 30 46 dB Att6 3000 ... 6000MHz 20 29 dB Input 925 ... 960MHz 1.5 2.0 Output 925 ... 960MHz 1.5 2.0 Input impedance (Single Ended) 50 Ohm Output impedance(Single Ended) 50 Ohm Maximum drive level 13 dBm Operating temperature -30 +85 deg. C Storage temperature -40 +85 deg. C Panasonic 2004.1.6 EGSM900 Rx SAW Filter ----- Unbalanced input and unbalanced output ----Part No. : Design No. : T942CL1 Panasonic 2004.1.6 EGSM900 Rx SAW Filter ----- Unbalanced input and unbalanced output ----Part No. : Design No. : T942CL1 Panasonic THIRD ANGLE PROJECTION UNLESS OTHERWISE SPECIFIED Tolerance : +/-0.05 Under Development BASIC DIMENSIONS UP TO 2.0 +/- 0.15 TOLERANCE INCL TO INCL TO INCL TO INCL 0.8 +/- 0.15 1.4 +/- 0.15 ABOVE 2-0.735 ISSUE 5-0.38 (2) (1) Input (2) GND (3) GND (4) Output (5) GND (3) DO NOT SCALE DRAWING (4) 0.075 (5) REVISIONS INDICATED BY ∆ DATE SCALE DRAW CHECK APPROVAL DRAWING NO. NAME 0.075 REVISIONS FINISH DESIGN 5-0.44 (1) MATERIAL Note : The design manufacturing process, and Specification of this device are subject to change without notice. ALL DIMENSIONS ARE IN MILLIMETERS TYPE NO. SAW Filter CERAMIC BUSINESS UNIT, LCR DEVICE COMPANY MATSUSHITA ELECTRONIC COMPONENTS CO.,LTD. KADOMA, OSAKA, JAPAN THIRD ANGLE PROJECTION UNLESS OTHERWISE SPECIFIED BASIC DIMENSIONS UP TO (2) S11 (3) S22 TOLERANCE INCL TO INCL TO INCL TO INCL ABOVE (1) (5) C S (4) D 0 Level S22 S11 1 S C 2 ISSUE 3 5 4 D S : Standard Signal Generator (Output Impedance 50 ohm) C : Frequency Counter D : Detector (Input Impedance 50 ohm) MATERIAL REVISIONS FINISH DESIGN DRAW CHECK APPROVAL DRAWING NO. Fig. 2 NAME TYPE NO. SAW filter CERAMIC BUSINESS UNIT , LCR DEVICE COMPANY MATSUSHITA ELECTRONIC COMPONENTS CO.,LTD. DO NOT SCALE DRAWING REVISIONS INDICATED BY ALL DIMENSIONS ARE IN MILLIMETERS KADOMA, OSAKA, JAPAN DATE SCALE UNLESS OTHERWISE SPECIFIED THIRD ANGLE PROJECTION BASIC DIMENSIONS UP TO Recommended land pattern TOLERANCE INCL TO INCL TO INCL TO INCL ABOVE 0.255 0.255 0.810 0.270 5-0.540 5-0.480 ISSUE MATERIAL 0.735 REVISIONS FINISH DATE SCALE DESIGN 0.735 DRAW CHECK APPROVAL DRAWING NO. NAME Note : The design manufacturing process, and Specification of this device are subject to change without notice. DO NOT SCALE DRAWING REVISIONS INDICATED BY ∆ ALL DIMENSIONS ARE IN MILLIMETERS TYPE NO. SAW Filter CERAMIC BUSINESS UNIT, LCR DEVICE COMPANY MATSUSHITA ELECTRONIC COMPONENTS CO.,LTD. KADOMA, OSAKA, JAPAN