bd9634gu e

Datasheet
Switching Regulator ICs
with Built-in FET (5V)
BD9634GU
Key Specifications
General Description




VBAT Supply Voltage:
2.5V to 5.5V
Oscillating Frequency 1:
1.0 MHz(Typ)
Oscillating Frequency 2:
500kHz(Typ)
ON-Resistance
CH2 PMOS
1.2Ω(Typ)
CH3 PMOS
0.45Ω(Typ)
CH3 NMOS
0.30Ω(Typ)
CH4 PMOS DOWN,UP side
0.45Ω(Typ)
CH4 NMOS DOWN,UP side
0.30Ω(Typ)
CH6 Load Switch
0.40Ω(Typ)
CH7 PMOS
4.00Ω(Typ)
CH7 NMOS
0.70Ω(Typ)
CH9 PMOS
0.90Ω(Typ)
 Operating Temperature Range:
-20°C to +85°C
BD9634GU is a system switching regulator IC for
DSC/DVC applications to generate plural voltage high
efficiently from battery. Component for Power FET and
phase compensation are embedded so it is suitable for
compact type DSC/DVC application.
Features










7ch DC/DC converter, 2ch LDO embedded
Startup ch,Motor
・CH1 Boost
－
・CH2 LDO
FET embedded
Analog
・CH3 Buck
FET embedded
Core
・CH4 Buck-Boost FET embedded
Digital
・CH5 Boost/Buck
－
CMOS, Memory
・CH6 Boost
－
LED
・CH7 Boost
FET embedded
CCD
・CH8 Reverse
－
CCD
・CH9 LDO
FET embedded
Analog
Low voltage operation 2.5[V]
CH1 supply voltage output for internal circuit
CH1 PWM / PFM selectable
CH4 Boost-Buck auto switching
CH5 Boost/Buck external switching
CH6,CH7 integrated Boost output shutdown
・CH7: Back Gate Control Function
・CH6: Load Switch integrated
Soft-start correspondence to each channel ch
・CH3→CH4 Sequence Control integrated
・CH7→CH8 2-types Sequence Control
Output Current Limiter (CH2,CH9),
Short Circuit Protection Function (CH3 to CH8)
Error Amp Phase Compensation integrated
(CH1,CH3,CH4,CH6 to CH8)
Operating Frequency 1[MHz](CH1,CH3 to CH5）
500[KHz](CH6 to CH8)
○Product structure : Silicon monolithic integrated circuit
.www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・14・001
Package
VCSP85H4
W (Typ) x D (Typ) x H (Max)
4.26mm x 4.26mm x 1.00mm
〇This product has no designed protection against radioactive rays.
1/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
Pin Configuration
BOTTOM VIEW
H
H1
VOUT4
USW4
PGND4
PGND4
DSW4
VBAT4
H8
G
VBAT3
VOUT4
USW4
XSHDN1
XSHDN34
DSW4
VBAT4
VOUT7
F
SW3
XSHDN5
CTL4
XSHDN2
CONT78
XSHDN78
SEL5
SW7
E
PGND13
XSHDN9
FB1
FB4
FB3
FB5
FB7
PGND78
D
PGND13
PREV1
FB2
AGND
FB6
VREF8
FB8
RT
C
OUT1
VDCO1
PREV56
VCC
AMPOUT5
VBAT8
VOUT8
B
VOUT2
VBAT
FB6.1
PGND56
XSHDN6
RESERVE
PWM/PFM
OUT8
A
A1
VBAT6
LSO6
OUT6
OUT5
VOUT9
VDCO4
A8
1
2
3
4
5
6
7
8
Pin Descriptions
Terminal No.
Name
Equivalent Circuit
Terminal No.
Name
Equivalent Circuit
O･G
1- E
PGND13
CH1,CH3 DRIVER GND terminal
Load switch input terminal
V
2- E
XSHDN9
CH9 shutdown terminal
Load switch output terminal
O
3- E
FB1
CH1 feedback terminal
G
OUT6
CH6 gate connecting terminal
O
4- E
FB4
CH4 feedback terminal
O･G
OUT5
CH5 gate connecting terminal
O
5- E
FB3
CH3 feedback terminal
G
1-A
A1
2-A
VBAT6
3-A
LSO6
4-A
5-A
TEST terminal
G
O･G
6-A
VOUT9
CH9 output terminal
O
6- E
FB5
CH5 feedback terminal
G
7-A
VDCO4
CH9 LDO power supply terminal
V
7- E
FB7
CH7 feedback terminal
G
8-A
A8
O･G
8- E
PGND78
CH7,CH8 DRIVER GND terminal
G
1-B
VOUT2
CH2 output terminal
O
1- F
SW3
CH3 switching terminal
O
2-B
VBAT
Battery input terminal
V
2- F
XSHDN5
CH5 shutdown terminal
O･G
3-B
FB6.1
CH6 feedback terminal
(Constant voltage side）
G
3- F
CTL4
CH4 output voltage switching terminal
O･G
O･G
TEST terminal
4-B
PGND56
CH5,CH6 DRIVER GND terminal
5-B
XSHDN6
CH6 shutdown terminal
6-B
RESERVE
Reserve terminal
7-B
PWM/PFM
CH1 PWM/PFM switching
terminal
G
4- F
XSHDN2
CH2 shutdown terminal
O・G
5- F
CONT78
CH7,CH8 sequence control terminal
O
6- F
XSHDN78
O・G
7- F
SEL5
CH5 Boost/Buck switching terminal
G
CH7 switching terminal
O
CH7,CH8 shutdown terminal
G
O･G
8-B
OUT8
CH8 gate connecting terminal
O
8- F
SW7
1-C
OUT1
CH1 gate connecting terminal
O
1- G
VBAT3
CH3 DRIVER power supply terminal
V
2-C
VDCO1
CH2 LDO power supply terminal
V
2- G
VOUT4
CH4 output terminal
O
CH4 Boost side switching terminal
O
3-C
－
4-C
PREV56
5-C
VCC
6-C
AMPOUT5
7-C
VBAT8
8-C
VOUT8
1-D
PGND13
2-D
PREV1
3-D
FB2
4-D
AGND
－
-
3- G
USW4
V
4- G
XSHDN1
CH1 shutdown terminal
Analog power supply terminal
V
5- G
XSHDN34
CH3,CH4 shutdown terminal
CH5 error amp output terminal
O
6- G
DSW4
CH4 Buck side switching terminal
CH8 DRIVER power supply terminal
V
7- G
VBAT4
CH4 DRIVER power supply terminal
V
CH8 output terminal
(for Discharge)
G
8- G
VOUT7
CH7 output terminal
O
CH1,CH3 DRIVER GND terminal
G
1- H
H1
CH1 DRIVER power supply terminal
V
2- H
VOUT4
CH4 output terminal
O
CH2 feedback terminal
G
3- H
USW4
CH4 Boost side switching terminal
O
Analog GND terminal
G
4- H
PGND4
CH4 DRIVER GND terminal
G
O・G
5- H
PGND4
CH4 DRIVER GND terminal
G
O
6- H
DSW4
CH4 Buck side switching terminal
O
G
7- H
VBAT4
CH4 DRIVER power supply terminal
(Note 1)
8- H
H8
CH5,CH6
terminal
DRIVER
power
supply
CH6 feedback terminal
(Constant voltage side）
5-D
FB6
6-D
VREF8
CH8 reference voltage
7-D
FB8
CH8 feedback terminal
8-D
RT
Triangle wave setting resistance
terminal
TEST terminal
TEST terminal
G
O･G
O
O･G
V
O･G
The letter on the right side of each pin explanation indicates the reaction if the terminal are not used.
O・・・OPEN
G・・・GND
O･G・・・OPEN or GND
V・・・Power supply (VBAT)
(Note 1)・・・10[KΩ]Pull-down
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
2/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
Block Diagram
PREV1
VOUT1
[CH1]
Boost
VOUT1
VBAT
PFM
FB1
PRE
DRIVER
PWM
OUT1
PGND13
MAX.
DUTY
PWM/PFM
VDCO1
[CH2]
LDO
VOUT2
LDO
control
VOUT3
[CH3]
Buck
VOUT2
VOUT2
FB2
VBAT3
FB3
SW3
PRE
DRIVER
VOUT3
PGND13
VOUT4
VOUT4
USW4
VOUT4
[CH4]
Buck-Boost
FB4
VBAT4
Buck-Boost
PWMCOMP
CTL4
PRE
DRIVER
DSW4
MAX.
DUTY
VOUT1
PGND4
OUT5
VOUT5
VOUT5
AMPOUT5
(While Buck setting)
FB5
[CH5]
Boost/Buck
VOUT5
Boost/Buck
PWMCOM
P
OUT5
PRE
DRIVER
MAX.
DUTY
(While Boost setting)
SEL5
VOUT1
VOUT6
PREV56
FB6
VBAT6
[CH6]
Boost
PRE
DRIVER
VOUT6
LSO6
OUT6
MAX.
DUTY
PGND56
FB6.1
VOUT7
[CH7]
Boost
VOUT7
VOUT7
FB7
PRE
DRIVER
SW7
MAX.
DUTY
PGND78
VOUT8
[CH8]
Reverse
VOUT8
Discharge
VBAT8
FB8
OUT8
PRE
DRIVER
VREF8
VOUT8
MAX.
DUTY
CH8 REF
VDCO4
[CH9]
LDO
LDO
control
VOUT9
VOUT9
RAMP,SAW
1[MHz]
500[KHz]
RT
VBAT
VBAT
XSHDN1
XSHDN2
XSHDN34
XSHDN5
XSHDN6
XSHDN78
XSHDN9
CONT78
Start circuits
TSD
VOUT1
VCC
CONTROL
Internal Power Supply
AGND
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
3/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
Absolute Maximum Ratings（Ta=25°C）
Parameter
Supply Voltage
Permissible Voltage
VOUT7 Permissible Voltage
Symbol
VVBAT
VVBAT3,4,6,8
VVOUT7
SW7 Permissible Voltage
VSW7
VOUT2 Permissible Current Output
SW3 Permissible Current Output
VOUT4 Permissible Current Output
LSO6 Permissible Current Output
VOUT7 Permissible Current Output
VOUT9 Permissible Current Output
Power Dissipation
Operating Temperature Range
Storage Temperature Range
Junction Temperature
IVOUT2
ISW3
IVOUT4
ILSO6
IVOUT7
IVOUT9
Pd
Topt
Tstg
Tjmax
Rating
Unit
-0.3 to +7
V
-0.3 to +15.5
-0.3 to +15.5
-0.3 to +16
0.3
0.5
1.0
0.5
0.5
0.3
1.4
-20 to +85
-55 to +150
+150
V
V
(Note 1)
A
A
A
A
A
A
W
°C
°C
°C
(Note 2)
(Note 1) 15.5[V] to 16[V] ： Pulse ≤40[ns] and Duty Cycle≤2[%]
(Note 2) Implemented on Glass epoxy board (ROHM standard board :50 x 58 x 1.75[mm3] 8 layers）
Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over
the absolute maximum ratings.
Recommended Operating Conditions
Parameter
VBAT Supply Voltage
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
Symbol
Limit
Unit
MIN
TYP
MAX
VVBAT
2.5
3.7
5.5
V
VVBAT3
2.5
3.7
5.5
V
VVBAT4
2.5
3.7
5.5
V
VVBAT6
VVBAT8
2.5
2.5
3.7
3.7
5.5
5.5
V
V
4/26
Conditions
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
Electrical Characteristics
（Unless otherwise specified, VVBAT=VVBAT3,4,6,8=3.7[V], VOUT1 Input Voltage=3.7[V], Ta=25[°C]）
Parameter
Symbol
Limit
MIN
TYP
MAX
Unit
Current Consumption
(PFM)
ICC1
-
90
180
µA
Current Consumption
(PWM)
ICC2
1.40
2.10
3.15
mA
Shutdown
Current Consumption
ICC3
-
0
10
µA
H Input Voltage1
VIH1
VVBAT
-0.3
-
-
V
L Input Voltage1
VIL1
-
-
GND
+0.3
V
H Input Voltage2
VIH3
2.5
-
-
V
V
・XSHDN1=H, PWM/PFM=L,
Other setting terminal=L
・Without load on each channel
・sum of VBAT terminal,
and VOUT1 terminal
・XSHDN1=H, PWM/PFM=H,
Other setting terminal =L
・Without load on each channel
・sum of VBAT terminal,
and VOUT1 terminal
・All setting terminal =L
・Without load on each channel
・sum of VBAT terminal,
and VOUT1 terminal
XSHDN1
L Input Voltage2
VIL3
-
-
GND
+0.3
H Input Voltage3
VIH3
VOUT1
-0.3
-
-
V
L Input Voltage3
VIL3
-
-
GND
+0.3
V
H Input Current1
IIH1
4.63
9.25
18.5
µA
H Input Current2
Conditions
Setting terminal except for XSHDN1, SEL5
SEL5
Input Voltage =3.7[V]
XSHDN2,XSHDN34,XSHDN5,XSHDN6,
XSHDN78,XSHDN9,PWM/PFM
Input Voltage =3.7[V] CTL4
IIH2
18.5
37
74
µA
Oscillating Frequency 1
fOSC1
0.8
1.0
1.2
MHz
RRT=10[kΩ]
Oscillating Frequency 2
Reduced-voltage
Detection Voltage
Reduced-voltage
Return Voltage
【CH1】
Error Amp Reference
Voltage
fOSC2
400
500
600
KHz
RRT=10[kΩ]
VUVLO1
1.60
1.80
2.00
V
VUVLO2
1.80
2.00
2.20
V
VEREF1
0.390
0.400
0.410
V
tSS1
0.44
1.08
1.72
ms
Soft-start period 100% 1.27[ms](TYP)
PWM/PFM=L
DMAX1
76.5
85.0
93.5
%
PWM/PFM=H
Reference Voltage
VREF2
0.291
0.300
0.309
V
Startup period 85%
PMOS ON-Resistance
tSS2
RONP2
0.73
-
1.45
1.20
2.17
1.95
ms
Ω
Soft-start Period 85%
Maximum Duty
PWM/PFM=H
【CH2】
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
5/26
Startup Period 100%
Power Supply 3.7[V]
1.7[ms]（TYP）
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
Electrical Characteristics –continued
（Unless otherwise specified, VVBAT=VVBAT3,4,6,8=3.7[V], VOUT1 Input terminal =3.7[V], Ta=25[°C]）
Parameter
Symbol
Limit
MIN
TYP
MAX
Unit
Conditions
【CH3】
Error Amp
Reference Voltage
Soft-start Period 85%
VEREF3
0.390
0.400
0.410
V
tSS3
0.43
0.85
1.27
ms
Soft-start Period 100% 1.0[ms]（TYP）
PMOS ON-Resistance
RONP3
-
0.45
0.70
Ω
Power Supply 3.7[V]
NMOS ON-Resistance
RONN3
-
0.30
0.55
Ω
Power Supply 3.7[V]
VEREF4
0.390
0.400
0.410
V
tSS4
1.25
2.50
3.75
ms
Soft-start Period 100%
2.94[ms]（TYP）
RONPD4
-
0.45
0.70
Ω
Power Supply 3.7[V]
RONND4
-
0.30
0.55
Ω
Power Supply 3.7[V]
RONPU4
-
0.45
0.70
Ω
Power Supply 3.7[V]
RONNU4
-
0.30
0.55
Ω
Power Supply 3.7[V]
DMAX4
65
80
95
%
VEREF5
0.975
1.000
1.025
V
tSS5
2.25
4.50
6.95
ms
Soft-start Period 100% 5.3[ms]（TYP）
DMAX5
76.5
85.0
93.5
%
SEL5=L
VEREF6
0.386
0.400
0.414
V
Constant voltage control side
VEREF6.1
0.386
0.400
0.414
V
Constant current control side
tSS6
2.55
5.10
7.65
ms
Soft-start Period 100% 6.0[ms]（TYP）
RONP6
-
0.40
0.65
Ω
Power Supply 3.7[V]
【CH4】
Error Amp
Reference Voltage
Soft-start Period 85%
PMOS ON-Resistance
DOWN side
NMOS ON-Resistance
DOWN side
PMOS ON-Resistance
UP side
NMOS ON-Resistance
UP side
Maximum Duty
【CH5】
Error Amp
Reference Voltage
Soft-start Period 85%
Maximum Duty
【CH6】
Error Amp
Reference Voltage 1
Error Amp
Reference Voltage 2
Soft-start Period 85%
Load Switch
ON-Resistance
Maximum Duty
DMAX6
87
-
-
%
【CH7】
Error Amp
Reference Voltage
Soft-start Period 85%
VEREF7
0.983
1.000
1.017
V
tSS7
3.40
6.80
10.20
ms
Soft-start Period 100% 8.0[ms]（TYP）
PMOS ON-Resistance
RONP7
-
4.00
6.40
Ω
Power Supply 3.7[V]
Power Supply 3.7[V]
RONN7
-
0.70
1.12
Ω
DMAX7
87
-
-
%
VEREF8
0.978
1.000
1.022
V
Soft-start Period 1 85%
tSS81
2.55
5.10
7.65
ms
Soft-start Period 2 85%
tSS82
3.40
6.80
10.20
ms
DMAX8
87
-
-
%
VREF8
2.44
2.50
2.56
V
VREF9
0.2425
0.250
0.2575
V
tSS9
127
255
383
μs
Startup Period 100%
RONP9
-
0.90
1.44
Ω
Power Supply 3.7[V]
NMOS ON-Resistance
Maximum Duty
【CH8】
Error Amp
Reference Voltage
Maximum Duty
CH8 Reference Voltage
Refer to P.16 for Output Voltage accuracy
Soft-start Period 100% 6.0[ms]（TYP）
CONT78=L
Soft-start Period 100% 8.0[ms]（TYP）
CONT78=H
【CH9】
Reference Voltage
Startup period 85%
PMOS ON-Resistance
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
6/26
300[μs]（TYP）
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
Function Description
【Features Summary】
Function
CH
CH1
Boost converter
CH2
LDO
Output voltage (TYP)
Power output
Setting res.
USE
External
External
Startup ch,Motor
Embedded
External
Analog
CH3
Buck converter
3.7[V] to 5.5[V]
I/O voltage differential
over 0.2[V]
1.05[V] to 1.8[V]
Embedded
External
Core
CH4
Buck-Boost converter
3.25[V]/3.3[V]
Embedded
Embedded
Digital
CH5
Boost/Buck converter
5.0[V]/1.8[V]
External
External
CMOS,Memory
CH6
Boost
6[V] to 16[V]
External
External
LED
CH7
Boost
12[V] to 14.5[V]
Embedded
External
CCD
CH8
Reverse
External
External
CCD
CH9
LDO
-7.5[V] to -6[V]
I/O voltage differential
over 0.2[V]
Embedded
Embedded
Analog
【CONTROL】
・Stand-by function related terminals
Following table shows start-up condition of each block.
XSHDN
1
PWM
/PFM
XSHDN
2
XSHDN
34
XSHDN
5
XSHDN
6
XSHDN
78
L
XSHDN
9
CH1
Internal
supply
RAMP
SAW
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
-
-
-
-
-
-
-
L
-
-
-
-
-
L
L
-
-
-
-
-
H
OFF
OFF
OFF
OFF
OFF
ON
H
H
L
L
L
L
L
L
OFF
OFF
OFF
OFF
OFF
OFF
H
L
L
L
L
L
ON
OFF
OFF
OFF
OFF
OFF
L
H
L
L
L
L
OFF
ON
OFF
OFF
OFF
OFF
L
L
H
L
L
L
OFF
OFF
ON
OFF
OFF
OFF
L
L
L
H
L
L
OFF
OFF
OFF
ON
OFF
OFF
L
L
L
L
H
L
OFF
OFF
OFF
OFF
ON
OFF
L
L
L
L
L
H
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
(Note) PWM/PFM logic refer to the table below.
(Note) -symbol mean without conditions.
・Other setting terminals
Terminal
PWM/PFM H：PWM operation
VOUT4
H
3.30[V]
CTL4
L
3.25[V]
SEL5
CONT78
Function
L：PFM operation
（Note）Latch logic at CH4 startup
H：Buck setting
L：Boost setting
H：CH7,CH8
startup synchronous
L：CH7→CH8 startup
（Note）H input voltage is VOUT1 output voltage
（Note）Logic after some [us] from rising edge of XSHDN78
・XSHDN2 to XSHDN9, PWM/PFM, CTL4 terminal equivalent circuit
VBAT
VBAT
XSHDN1,SEL5,CONT7 terminal is not
Pulled-down, so VBAT input and GND
input is needed.
30[kΩ]
400[kΩ]
(100[kΩ])
AGND
100[kΩ] is only for CTL4 terminal.
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
7/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
【CH1】
・Function
Selectable PWM/PFM boost DC/DC converter.
Output voltage is ranges from 3.7[V] to 5.5[V] (TYP) at PFM, 4.1[V] to 5.5[V] (TYP) at PWM.
Low voltage operation starts up from 2.5[V] and also provides supply voltage to VREF circuit.
VOUT1
PREV1
VOUT1
C1
D1
R1
C3
PFM
FB1
R2
PRE
DRIVER
PWM
OUT1
M1
VBAT
PGND13
0.4[V]
MAX.
DUTY
PWM/PFM
R3
VBAT
VBAT
L1
C2
C1
Startup Circuit
VOUT1
Setting External Components
・Recommended External Components
Parts Name
Value
Maker
Part Number
R1
Refer to the right table
-
-
R2
Refer to the right table
-
VOUT1
-
Setting
external
PFM
3.7[V]
PFM/PWM
4.2[V]
5.0[V]
R3
10[Ω]
-
-
R1
620[KΩ]+24[KΩ]
C1
22[μF] x 2
Taiyo Yuden
JMK212BJ226MG
R2
56[KΩ]+22[KΩ]
56[KΩ]
C2
10[μF]
Taiyo Yuden
JMK212BJ106KG
C3
100[pF]
100[pF]
C3
Refer to
the right table
Taiyo Yuden
TMK063BJ101KP
/TMK063BJ151KP
R1
510[KΩ]+22[KΩ]
R2
56[KΩ]+7.5[KΩ]+1[KΩ]
56[KΩ]
C4
L1
1[μF]
1.0[μH]
Taiyo Yuden
TOKO
JMK105BJ105KV
A997AS-1R0N
C3
150[pF]
150[pF]
M1 (Note)
D1
-
ROHM
ROHM
RTF015N03/RTR040N03
RB060M-30
VOUT1 
620[KΩ]+24[KΩ]
510[KΩ]+22[KΩ]
R1  R2
 0.4[V]
R2
(Note) It depends on output load current
・ Start-up Sequence
VBAT
2.5[V] to 5.5[V]
0[V]
VBAT[V]
XSHDN1
0[V]
When VBAT is 3.2[V] or less
3.7[V] to 5.5[V]
Discharge by load
≈VBAT[V]
VOUT1
0[V]
ON_delay
SOFT
Soft start time
・PWM/PFM
H input voltage
PWM/PFM
VOUT1
0[V]
3.7[V] to 5.5[V]
PFM operation
PWM operation
PFM operation
（Load 10mA or less)
（Load 10mA or less)
Select PWM/PFM with light load (10mA or less).
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
8/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
【Internal Supply Voltage】
・Function
Regulator input voltage is supplied by VOUT1.
Output voltage is 2.5[V]（TYP）.
No output terminal for internal power supply.
VREF voltage is used to power up internal circuit.
Internal supply rises up at PWM mode (PWM/PFM terminal=H) or CH9 turns ON (XSHDN9=H).
VCC
VOUT1
Reference
Voltage
Internal supply
・Start-up Sequence
3.7[V] to 5.5[V]
VCC
H input voltage
PWM/PFM
or
XSHDN9
0[V]
2.5[V]
Internal
Supply
0[V]
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
9/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
【CH2】
・Function
LDO for minimum I/O voltage differential is 0.2[V] or more.
Input voltage is VOUT1, output voltage is ranges from 1.8[V] to 3.5[V] (TYP).
VDCO1
VOUT1
CURRENT
LIMIT
Reference
Voltage
VOUT2
VOUT2
R1
C2
R3
FB2
C1
R2
・Recommended External
Parts name
Value
Refer to the right table
Refer 右表参照
to the right table
R1
R2
R3
C1
C2
200[mΩ]
2.2[μF]
15[pF]
Maker
Part number
Taiyo Yuden
Taiyo Yuden
JMK107BJ225KA
TMK063CH150JP
VOUT2
R1
R2
3.3[V]
300[KΩ]
30[KΩ]
VOUT2 
2.5[V]
300[KΩ]
30[KΩ]+11[KΩ]
R1  R2
 0.3[V]
R2
・Start-up Sequence
4.1[V] to 5.5[V]
VDCO1
H input voltage
PFM/PWM
H input voltage
XSHDN2
0[V]
1.8[V] to 3.5[V]
Discharge
VOUT2
0[V]
Startup period
1.7[ms]
・Over Current Protection
Characteristics of output voltage and output current shown below.
VOUT2
IOUT2
100[mA]
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
300[mA]
10/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
【CH3】
・Function
Synchronous rectification type buck DC/DC converter with built in power MOS output stage.
Output voltage ranges from 1.05[V] to 1.8[V]（TYP）.
VOUT3
VBAT
VBAT3
R1
C3
C2
FB3
R2
SW3
PRE
DRIVER
VOUT3
L1
0.4[V]
C1
PGND13
SAW
・Recommended External
Maker
VOUT3
Setting
external
Parts name
Value
Part number
R1
Refer to the right table
-
-
R1
270[KΩ]
270[KΩ]
270[KΩ]
R2
Refer to the right table
-
-
R2
160[KΩ]+6.2[KΩ]
120[KΩ]+5.6[KΩ]
75[KΩ]+2.2[KΩ]
C1
10[μF]
Taiyo Yuden
JMK212BJ106KG
C2
1[μF]
Taiyo Yuden
JMK105BJ105KV
C3
10[pF]
Taiyo Yuden
TMK063CH100DT
L1
4.7[μH]
sumida
CDRH2D14NP-4R7NC
1.05[V]
VOUT3 
1.26[V]
1.8[V]
R1  R2
 0.4[V]
R2
・Start-up Sequence
VBAT3
2.5[V] to 5.5[V]
PWM/PFM H input voltage
H input voltage
XSHDN34
0[V]
1.05[V] to 1.8[V]
VOUT3
Discharge
0[V]
Soft start period
1.0[ms]
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
11/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
【CH4】
・Function
Synchronous rectification cross converter with built-in power MOS output stage.
Output voltage is selectable: 3.25[V]/3.3[V]（TYP）.
VOUT4
VOUT4
C1
USW4
PGND4
FB4
VOUT4
VBAT4
Place a resistance to
change setting
voltage by external.
VBAT
L1
C2
Buck-Boost
PWMCOMP
CTL4
PRE
DRIVER
DSW4
0.4[V]
MAX.
DUTY
SAW
・Recommended External
Parts name
Value
C1
22[μF]
Taiyo Yuden
Maker
JMK212BJ226MG
Part number
C2
10[μF]
Taiyo Yuden
JMK212BJ106KG
L1
4.7[μH]
sumida
CDRH2D14NP-4R7NC
・ Start-up Sequence
VBAT4
PWM/PFM
2.5[V] to 5.5[V]
H input voltage
H input voltage
XSHDN34
0[V]
70[%]
VOUT3
1.05[V] to 1.8[V]
0[V]
Discharge
3.25[V]/3.3[V]
VOUT4
0[V]
Soft start period
2.94[ms]
・Setting Voltage
It is possible to return in a set voltage by adding external resistance between VOUT4 and FB4.
CTL4=L, OPEN
330.7[kΩ]  ExternalR[kΩ]
VOUT4 
 0.4[V]
40.7[kΩ]
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
CTL4=H
VOUT4 
12/26
330[kΩ]  ExternalR[kΩ]
 0.4[V]
40[kΩ]
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
【CH5】
・Function
Boost/Buck selectable DC/DC converter.
Output voltage is selectable: 5.0[V] /1.8[V] (TYP).
VBAT
SEL5
VOUT5
R3
C4
AMPOUT5
VOUT1
C2
L1
Buck setting
Boost setting
R1
US1
VOUT5
FB5
Boost/Buck
PWMCOMP
R4
C3
OUT5
OUT5
PRE
DRIVER
C2
C1
R2
US1
VOUT5
1.0[V]
C1
MAX.
DUTY
SAW
・Recommended External
Value
Parts name
Part number
Maker
Boost setting
Buck setting
Output=4.8[V]
Output=1.8[V]
Boost setting
Buck setting
Output=4.8[V]
Output=1.8[V]
R1
91[KΩ]
24[KΩ]
-
-
-
R2
24[KΩ]
R3
2[KΩ]
30[KΩ]
-
-
-
1[KΩ]
-
-
-
R4
10[KΩ]
62[KΩ]
-
-
-
C1
22[μF]
22[μF]
Taiyo Yuden
JMK212BJ226MG
JMK212BJ226MG
C２
1[μF]
10[μF]
Taiyo Yuden
JMK105BJ105KV
JMK212BJ106KG
C3
100[pF]
100[pF]
Taiyo Yuden
TMK063CH101JP
TMK063CH101JP
C4
2.2[nF]
10[nF]
Taiyo Yuden
LMK063BJ222KP
LMK063BJ103KP
L1
1.5[μH]
1.8[μH]
sumida
CDRH2D14NP-1R5NC
CDRH2D14NP-1R8NC
US1 (Note)
-
-
ROHM
US5U1/QS5U12
US5U29
(Note) Depends on output load current.
VOUT5 
R1  R2
 1.0[V]
R2
・Start-up Sequence
2.5[V] to 5.5[V]
VBAT
0[V]
H input voltage
PWM/PFM
0[V]
H input voltage
XSHDN5
VOUT5
(Boost)
0[V]
5.0[V]
Discharge by load
1.8[V]
Discharge by load
≈VBAT[V]
0[V]
ON-delay
SOFT
Soft start period
5.3[ms]
VOUT5
(Buck)
0[V]
Soft start period
5.3[ms]
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
13/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
【CH6】
・Function
Boost DC/DC converter with built-in load switch.
This channel enables constant voltage operation and constant voltage operation for protection.
The constant voltage is available with output of 6[V] to 16[V] (TYP).
The load switch turns OFF when XSHDN6 goes LOW (CH6 shutdown) and the timer latch.
VOUT1
VBAT or VOUT1
PREV56
VBAT6
FB6
VOUT6
C2
L1
Place a resistance to
change setting voltage
by external.
PRE
DRIVER
VOUT6
LSO6
C1
OUT6
0.4[V]
MAX.
DUTY
PGND56
US1
SAW
0.4[V]
FB6.1
R1
・Recommended External
Parts name
Value
R1
20[Ω]
Maker
Part number
C1
4.7[µF]
Taiyo Yuden
C2
1[µF]
Taiyo Yuden
JMK105BJ105KV
L1
10[µF]
sumida
CDRH2D14NP-100NC
US1
-
ROHM
US5U1
-
EMK212BJ475KG
・Start-up Sequence
VBAT6
2.5[V] to 5.5[V]
PWM/PFM
H input voltage
H input voltage
XSHDN6
0[V]
6[V] to16[V]
Discharge by load
≈VBAT[V]
VOUT6
0[V]
ON_delay
SOFT
Soft start period
6.0[ms]
・Set Voltage when Fixed Voltage is Driven
When a fixed voltage is driven by internal resistance, it is set to 16V.
It is possible to return in a set voltage by adding external resistance between VOUT6 and FB6.
However, note the resisting pressure of the capacitance of C1 when stepping up the voltage
applying external resistance.
VOUT6 
ExternalR  400[kΩ]
 0.4[V]
10[kΩ]
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
14/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
【CH7】
・Function
Synchronous rectification Boost DC/DC converter with integrated output stage power MOS.
Output voltage ranges from 12.0[V] to 14.5[V] (TYP).
Output can shut by back gate control function.
Back gate control function is a function to shut the output by placing back gate of PMOS to SW7 side when in XSHDN78=L
(CH7 shut down) time and a timer latch.
VOUT7
VOUT7
R1
C3
VOUT7
or
FB7
VBAT
C1
D1
R2
PRE
DRIVER
1.0[V]
SW7
MAX.
DUTY
MAX.
DUTY
C2
L1
PGND78
SAW
・Recommended External
Parts name
Value
Maker
Part number
R1
Refer to the right table
-
-
R2
Refer to the right table
-
-
C1
10[μF]
Taiyo Yuden
EMK212BJ106KG
C2
10[μF]
Taiyo Yuden
JMK212BJ106KG
C3
150[pF]
Taiyo Yuden
TMK063BJ151KP
L1 (Note)
22[μH]
sumida
CDRH2D14B/LDNP-220M
D1 (Note)
-
ROHM
VOUT7
Setting
external
12[V]
13[V]
R1
820[KΩ]
820[KΩ]
R2
75[KΩ]
68[KΩ]
VOUT7 
R1  R2
 1.0[V]
R2
RB551V-30
(Note) If output voltage ranges from 13[V] to 14[V], place D1.
・Start-up Sequence
Refer to [CH8] Start-up Sequence in Page 16.
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
15/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
【CH8】
・Function
Reverse DC/DC Converter.
Output voltage ranges from -7.5[V] to -6.0[V] (TYP).
VOUT8
VBAT
VBAT8
R1
C3
FB8
C2
R2
OUT8
PRE
DRIVER
VOUT8
1.0[V]
(EREF8)
US1
MAX.
DUTY
VREF8
L1
MAX.
DUTY
C1
PGND78
CH8 REF
VOUT8
SAW
Discharge
・Recommended External
Parts name
Value
Maker
Part number
R1
Refer to the right table
-
-
R2
Refer to the right table
-
-
C1
10[μF] x 2
Taiyo Yuden
LMK212BJ106KG
C2
1[μF]
Taiyo Yuden
JMK105BJ105KV
C3
100[pF]
Taiyo Yuden
TMK063CH101JP
L1
2.2[μH]
sumida
CDRH2D14NP-2R2NC
US1
-
ROHM
QS5U21
VOUT8
Setting
external
-7.5[V]
-6[V]
R1
680[KΩ]
560[KΩ]
R2
120[KΩ]
120[KΩ]
VOUT8  
R1
R1  R2
VREF8 
EREF8
R2
R2
Output voltage accuracy is calculated by the above formula.
・Start-up Sequence
＜CONT78=L＞
VBAT8
2.5[V] to 5.5[V]
H input voltage
PWM/PFM
0[V]
2.5[V]
VREF8
0[V]
H input voltage
XSHDN78
0[V]
70[%]
Discharge by load
12[V] to 14[V]
≈VBAT[V]
VOUT7
0[V]
ON_delay
SOFT
Soft start period
8.0[ms]
VOUT8
0[V]
Discharge
Soft start period
6.0[ms]
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
16/26
-7.5[V] to -6[V]
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
＜CONT78=H＞
VBAT8
2.5[V] to 5.5[V]
H input voltage
PWM/PFM
0[V]
2.5[V]
VREF8
0[V]
H input voltage
XSHDN78
0[V]
12[V] to 14[V]
Discharge by load
≈VBAT[V]
VOUT7
0[V]
ON_delay
SOFT
Soft start period
8.0[ms]
VOUT8
0[V]
Discharge
-7.5[V] to -6[V]
Soft start period
8.0[ms]
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
17/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
【CH9】
・Function
LDO with the minimum I/O voltage differential is 0.2[V] or more.
Output voltage is 1.8[V] (TYP).
Input voltage (2.5[V] to 5.5[V]) is input to VDCO4 even in PFM mode and output 1.8[V] (TYP) if it becomes
XSHDN9=H
Input voltage
2.5[V] to 5.5[V]
VDCO4
CURRENT
LIMIT
Reference
Voltage
VOUT9
VOUT9
C1
・Recommended External
Parts name
Value
Maker
Part number
C1
2.2[μF]
Taiyo Yuden
JMK107BJ225
KA
・Start-up Sequence
2.5[V] to 5.5[V]
VDCO4
H input voltage
XSHDN9
0[V]
2.5[V]
Internal
Supply
1.8[V]
Discharge by load
0[V]
VOUT9
Startup period
300[μs]
・Over Current Protection
Characteristics of output voltage and output current shown below.
VOUT9
IOUT9
50[mA]
250[mA]
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
18/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
【Short Protection Function】
 CH3 to CH8 are monitoring error amp input voltage fed backed from output and enable timer circuit with falling
below the detection voltage of short protection circuit. Timer latch circuit will latch power MOS to OFF status of CH2
to CH9 if such condition remained for 1.0[ms]. If VOUT5 is shorted during CH5 Boost setting, Short Protection
Circuit will be disabled with falling below the detection voltage of input voltage.
 All channel except CH1 will be latched with any other channels to be over-current and/or shorted.
 Latch will be released either setting XSHDN1=GND, PWM/PFM=GND, XSHDN9=GND or restarting the device.
 Short detection comparator will be disabled by soft start.
 The timer latch circuit doesn't operate in PFM mode.
VOUT3
FB3
VOUT4
0.2[V]
FB4
0.2[V]
VOUT5
.
FB5
0.5[V]
Timer Latch Circuit
Latch with the following condition :CH2 to CH9
CH2：PMOS OFF
CH3：SW3=Hiz
VOUT6
CH4：DSW4=Hiz
up side=PMOS ON
NMOS OFF
CH5：Boost OUT5=Low
Buck OUT5=High
CH6：Load switch OFF
OUT6=Low
CH7：PMOS OFF BG=SW7 side
NMOS OFF
CH8：OUT8=High
CH9：PMOS OFF
FB6
0.4[V]
VOUT7
FB7
0.5[V]
VOUT8
FB8
VREF8
1.29[V]
【Thermal shutdown function】
Thermal shutdown function is built in to prevent IC from heat distraction.
Thermal circuit will be disabled by PFM.
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
19/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
I/O Equivalent Circuits
Terminal
No.
Terminal
Name
4-G
7-B
4-F
5-G
3-F
2-F
7-F
5-B
6-F
5-F
2-E
4-E
2-C
1-B
7-A
6-A
5-C
XSHDN1
PWM/PFM
XSHDN2
XSHDN34
CTL4
XSHDN5
SEL5
XSHDN6
XSHDN78
CONT78
XSHDN9
FB4
VDCO1
VOUT2
VDCO4
VOUT9
VCC
Terminal
No.
Terminal
Name
3-E
3-D
5-E
6-E
3-B
7-E
7-D
6-B
8-D
1-A
8-A
1-H
8-H
FB1
FB2
FB3
FB5
FB6.1
FB7
FB8
RESERVE
RT
A1
A8
H1
H8
Terminal
No.
Terminal
Name
5-D
FB6
Equivalent Circuit
Terminal
No.
Terminal
Name
2-D
1-C
2-G, 2-H
3-G, 3-H
4-C
5-A
4-A
PREV1
OUT1
VOUT4
USW4
PREV56
OUT5
OUT6
Equivalent Circuit
PGND
AGND
Equivalent Circuit
VBAT
Terminal
No.
Terminal
Name
1-F
6-G, 6-H
3-A
8-B
SW3
DSW4
LSO6
OUT8
Equivalent Circuit
VBAT
AGND
PGND
Equivalent Circuit
Terminal
No.
Terminal
Name
8-G
8-F
VOUT7
SW7
Equivalent Circuit
High resisting
pressure
PGND
AGND
Terminal
No.
Terminal
Name
2-B
1-G
7-G, 7-H
2-A
7-C
VBAT
VBAT3
VBAT4
VBAT6
VBAT8
Equivalent Circuit
VBAT
VBAT3
VBAT4
VBAT6
VBAT8
Terminal
No.
Terminal
Name
4-D
1-D,1-E
4-H,5-H
4-B
8-E
AGND
PGND13
PGND4
PGND56
PGND78
Equivalent Circuit
AGND
PGND
PGND
Terminal
No.
Terminal
Name
8-C
VOUT8
AGND
Equivalent Circuit
Terminal
No.
Terminal
Name
6-C
6-D
AMPOUT5
VREF8
VBAT
Equivalent Circuit
VCC
×2
AGND
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
20/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
Power Dissipation PD[W]
Power Dissipation
1.4[W]
1.5
1
0.5
0
85
150
Ambient Temperature
Ta[℃]
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
21/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
Operational Notes
1.
Reverse Connection of Power Supply
Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power
supply pins.
2.
Power Supply Lines
Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the
digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog
block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and
aging on the capacitance value when using electrolytic capacitors.
3.
Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.
4.
Ground Wiring Pattern
When using both small-signal and large-current ground traces, the two ground traces should be routed separately but
connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal
ground caused by large currents. Also ensure that the ground traces of external components do not cause variations
on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.
5.
Thermal Consideration
Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in
deterioration of the properties of the chip. In case of exceeding this absolute maximum rating, increase the board size
and copper area to prevent exceeding the Pd rating. (Refer page 20)
6.
Recommended Operating Conditions
These conditions represent a range within which the expected characteristics of the IC can be approximately obtained.
The electrical characteristics are guaranteed under the conditions of each parameter.
7.
Inrush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow
instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power
supply. Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and
routing of connections.
8.
Operation Under Strong Electromagnetic Field
Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.
9.
Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may
subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply
should always be turned off completely before connecting or removing it from the test setup during the inspection
process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during
transport and storage.
10. Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and
unintentional solder bridge deposited in between pins during assembly to name a few.
11. Unused Input Pins
Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and
extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small
charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and
cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the
power supply or ground line.
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
22/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
Operational Notes – continued
12. Regarding the Input Pin of the IC
This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them
isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a
parasitic diode or transistor. For example (refer to figure below):
When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode.
When GND > Pin B, the P-N junction operates as a parasitic transistor.
Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual
interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to
operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be
avoided.
Resistor
Transistor (NPN)
Pin A
Pin B
C
E
Pin A
N
P+
P
N
N
P+
N
Pin B
B
Parasitic
Elements
N
P+
N P
N
P+
B
N
C
E
Parasitic
Elements
P Substrate
P Substrate
GND
GND
Parasitic
Elements
GND
Parasitic
Elements
GND
N Region
close-by
Figure 1. Example of monolithic IC structure
13. Thermal Shutdown Circuit(TSD)
This IC has a built-in thermal shutdown circuit that prevents heat damage to the IC. Normal operation should always
be within the IC’s power dissipation rating. If however the rating is exceeded for a continued period, the junction
temperature (Tj) will rise which will activate the TSD circuit that will turn OFF all output pins. When the Tj falls below
the TSD threshold, the circuits are automatically restored to normal operation.
Note that the TSD circuit operates in a situation that exceeds the absolute maximum ratings and therefore, under no
circumstances, should the TSD circuit be used in a set design or for any purpose other than protecting the IC from
heat damage.
14. Disturbance light
In a device where a portion of silicon is exposed to light such as in a WL-CSP, IC characteristics may be affected due
to photoelectric effect. For this reason, it is recommended to come up with countermeasures that will prevent the chip
from being exposed to light.
15. Board Patterning
・VBAT,VBAT3,VBAT4,VBAT6,VBAT8 must be connected to the power supply on the board.
・VCC must be connected to VOUT1 output on the board.
・ALL PGND and AGND must be connected to GND on the board.
・ALL power supply line and GND terminals must be wired with wide/short pattern in order to achieve the lowest
impedance possible.
16. Peripheral Circuitry
・Use low ESR ceramic capacitor for bypass capacitor and place them as close as possible between power supply and
GND terminals.
・Place external components such as L and C by IC using wide and short PCB trace patterns.
・Draw output voltage from each end of capacitor.
・Causing short circuit at CH1, CH5(Boost) output will overload the external diode and may breakdown the component.
Prepare physical countermeasures by adding poli-switches and fuses to avoid excess current flow.
17. Start-up
・Keep light load condition when starting up the device.
・Switch to PWM mode after CH1 has started up in PFM mode, and the VOUT1 output voltage is stable.
CH2 to CH8 should starts after or simultaneously with PWM mode.
18. Usage of this Product
This IC is designed to be used in DSC/DVD application. When using in other applications, please be sure to consult
with our sales representative in advance.
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
23/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
Ordering Information
B
D
9
6
3
Package Name
4
G
U
-
Package
GU: VCSP85H4
E2
Packaging and forming specification
E2: Embossed tape and reel
Marking Diagram
VCSP85H4
(TOP VIEW)
1PIN MARK
Part Number Marking
BD9634
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
LOT Number
24/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
Physical Dimension, Tape and Reel Information
Package Name
VCSP85H4(BD9634GU)
LOT No.
Tape
Quantity
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
Embossed carrier tape (Heat sealed)
2500pcs
25/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
BD9634GU
Revision History
Date
Revision
26.Apr.2016
001
Changes
New Release
www.rohm.com
© 2016 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
26/26
TSZ02201-0313AA400620-1-2
26.Apr.2016 Rev.001
Notice
Precaution on using ROHM Products
1.
Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
(Note 1)
intend to use our Products in devices requiring extremely high reliability (such as medical equipment
, transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅣ
CLASSⅢ
2.
ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3.
Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4.
The Products are not subject to radiation-proof design.
5.
Please verify and confirm characteristics of the final or mounted products in using the Products.
6.
In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7.
De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8.
Confirm that operation temperature is within the specified range described in the product specification.
9.
ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1.
When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2.
In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PGA-E
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.003
Precautions Regarding Application Examples and External Circuits
1.
If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2.
You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1.
Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2.
Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3.
Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4.
Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1.
All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2.
ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3.
No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1.
This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2.
The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3.
In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4.
The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PGA-E
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.003
Datasheet
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3.
The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or
concerning such information.
Notice – WE
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.001