TSOP373..H, TSOP375..H www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATUES • Very low supply current • Photo detectors and preamplifier in one package • Internal filter for PCM frequency • Supply voltage: 2.5 V to 5.5 V • Improved immunity against ambient light • Insensitive to supply voltage ripple and noise • External metal shield • Material categorization: for definitions of compliance www.vishay.com/doc?99912 22594 please see DESCRIPTION The TSOP373..H, TSOP375..H series are miniaturized receiver modules for infrared remote control systems. A PIN diode and a preamplifier are assembled on a PCB, the epoxy lens cap contains an IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. ORDERING CODE Taping: TSOP37...TT - top view taped TSOP37...TR - side view taped The TSOP373..H series devices are optimized to suppress almost all spurious pulses from energy saving lamps like CFLs. AGC3 may also suppress some data signals if continuously transmitted. New designs should prefer the TSOP373..H series. The TSOP375..H series contain a very robust AGC5. This series should only be used for critically noisy environments. These components have not been qualified according to automotive specifications. PARTS TABLE NOISY ENVIRONMENTS AND SHORT BURSTS (AGC3) VERY NOISY ENVIRONMENTS AND SHORT BURSTS (AGC5) 36 kHz TSOP37336H (1) TSOP37536H 38 kHz TSOP37338H (2)(3)(4)(5) TSOP37538H 40 kHz TSOP37340H TSOP37540H 56 kHz TSOP37356H AGC Carrier frequency TSOP37556H Package Belobog shield Pinning 1 = OUT; 2, 3, 6, 7, 8 = GND; 4, 5 = VS Dimensions (mm) 4.3 W x 4.3 H x 1.0 D Mounting SMD Application Best remote control code Rev. 1.5, 10-Nov-15 Remote control (1) MCIR (2) Mitsubishi 1 (3) RECS-80 Code (4) r-map (5) XMP-1, SMP-2 Document Number: 82643 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP373..H, TSOP375..H www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 17170_5 4, 5 R1 Transmitter with TSALxxxx VS 30 kΩ IR receiver VS Input Demodulator Band pass AGC OUT VO GND GND Control circuit µC OUT 2, 3, 6, 7, 8 PIN + VS C1 Circuit 1 GND R1 and C1 are recommended for protection against EOS. Components should be in the range of 33 Ω < R1 < 1 kΩ, C1 > 0.1 µF. 20445-5 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT VS -0.3 to +6 V mA Supply voltage Supply current IS 3 Output voltage VO -0.3 to (VS + 0.3) V Output current IO 5 mA Tj 100 °C Storage temperature range Junction temperature Tstg -25 to +85 °C Operating temperature range Tamb -25 to +85 °C Ptot 10 mW Power consumption Tamb ≤ 85 °C Note • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability. ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION Supply voltage SYMBOL MIN. TYP. MAX. UNIT VS 2.5 - 5.5 V VS = 3.3 V, Ev = 0 ISD 0.27 0.35 0.45 mA Ev = 40 klx, sunlight ISH - 0.45 - mA Ev = 0, IR diode TSAL6200, IF = 200 mA, test signal see Fig. 1 d - 45 - m Output voltage low IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1 VOSL - - 100 mV Minimum irradiance Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1 Ee min. - 0.12 0.25 mW/m2 Maximum irradiance tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1 Ee max. 30 - - W/m2 Angle of half transmission distance ϕ1/2 - ± 75 - deg Supply current Transmission distance Directivity Rev. 1.5, 10-Nov-15 2 Document Number: 82643 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP373..H, TSOP375..H www.vishay.com Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) Optical Test Signal (IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = f0, t = 10 ms) 0.8 ton, toff - Output Pulse Width (ms) Ee t tpi *) T *) tpi ≥ 6/f0 is recommended for optimal function Output Signal VO 1) 2) VOH VOL td 14337 3/f0 < td < 9/f0 tpi - 4/f0 < tpo < tpi + 6/f0 1) tpo 0.6 0.5 toff 0.4 0.3 0.2 λ = 950 nm, optical test signal, Fig. 3 0.1 0 0.1 t 2) ton 0.7 1 10 100 1000 10 000 Ee - Irradiance (mW/m2) 20759 Fig. 1 - Output Function Fig. 4 - Output Pulse Diagram 0.40 Ee min./Ee - Relative Responsivity tpo - Output Pulse Width (ms) 1.2 0.35 0.30 0.25 Output pulse width 0.20 0.15 Input burst length 0.10 0.05 λ = 950 nm, optical test signal, Fig. 1 0 0.1 1 10 100 1000 1.0 0.8 0.6 0.4 10 000 0.0 0.7 Ee - Irradiance (mW/m²) 20760 f = f0 ± 5 % Δf(3 dB) = f0/10 0.2 Fig. 2 - Output Pulse Width vs. Irradiance Optical Test Signal 600 µs t 600 µs t = 60 ms VO 94 8134 Output Signal, (see Fig. 4) VOH VOL t on t off t 1.3 4.0 Correlation with ambient light sources: 2 3.5 10 W/m = 1.4 klx (std. illum. A, T = 2855 K) 10 W/m2 = 8.2 klx (daylight, T = 5900 K) 3.0 Wavelength of ambient illumination: λ = 950 nm 2.5 2.0 1.5 1.0 0.5 20757 Fig. 3 - Output Function Rev. 1.5, 10-Nov-15 1.1 Fig. 5 - Frequency Dependance of Responsivity Ee min. - Threshold Irradiance (mW/m2) Ee 0.9 f/f0 - Relative Frequency 16925 0 0.01 0.1 1 10 100 Ee - Ambient DC Irradiance (W/m2) Fig. 6 - Sensitivity in Bright Ambient 3 Document Number: 82643 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP373..H, TSOP375..H www.vishay.com Vishay Semiconductors 1.0 S(λ)rel - Relative Spectral Sensitivity Ee min. - Threshold Irradiance (mW/m2) 1.0 f = 100 Hz 0.9 0.8 f = 10 kHz 0.7 0.6 f = 20 kHz 0.5 0.4 f = 30 kHz 0.3 f = fo 0.2 0.1 10 100 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 750 800 850 900 950 1000 1050 1100 1150 0 1 0.9 1000 λ - Wavelength (nm) VsRMS - AC Voltage on DC Supply Voltage (mV) 20753 Fig. 7 - Sensitivity vs. Supply Voltage Disturbances Fig. 10 - Relative Spectral Sensitivity vs. Wavelength 1 Max. Envelope Duty Cycle 0.9 -20° f = 38 kHz, Ee = 2 mW/m² 0.8 -10° 0° 10° 20° -30° 30° -40° 0.7 40° -50° 0.6 50° 60° -60° 0.5 0.4 -70° 70° 0.3 -80° TSOP373..H 0.2 80° 0.1 TSOP375..H 0 0 20 40 60 80 100 0.1 21947 0.3 0.5 0.7 0.9 120 Burst Length (number of cycles/burst) Fig. 11 - Directivity 0.30 0.30 Ee min. - Sensitivity (mW/m2) Ee min. - Threshold Irradiance (mW/m2) Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length 0.25 0.20 0.15 0.10 0.05 0.25 0.20 0.15 0.10 0.05 0.00 0 -30 -10 10 30 50 70 1 90 Fig. 9 - Sensitivity vs. Ambient Temperature Rev. 1.5, 10-Nov-15 2 3 4 5 VS - Supply Voltage (V) Tamb - Ambient Temperature (°C) Fig. 12 - Sensitivity vs. Supply Voltage 4 Document Number: 82643 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP373..H, TSOP375..H www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT IR Signal The TSOP373..H, TSOP375..H series is designed to suppress spurious output pulses due to noise or disturbance signals. The devices can distinguish data signals from noise due to differences in frequency, burst length, and envelope duty cycle. The data signal should be close to the device’s band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. When a data signal is applied to the TSOP373..H, TSOP375..H in the presence of a disturbance, the sensitivity of the receiver is automatically reduced by the AGC to insure that no spurious pulses are present at the receiver’s output. Some examples which are suppressed are: 0 • DC light (e.g. from tungsten bulbs sunlight) 5 • Continuous signals at any frequency 10 15 20 Time (ms) 16920 Fig. 13 - IR Signal from Fluorescent Lamp with Low Modulation IR Signal • Strongly or weakly modulated patterns from fluorescent lamps with electronic ballasts (see Fig. 13 or Fig. 14) 0 5 10 15 20 Time (ms) 16921 Fig. 14 - IR Signal from Fluorescent Lamp with High Modulation TSOP373..H TSOP375..H Minimum burst length 6 cycles/burst 6 cycles/burst After each burst of length a minimum gap time is required of 6 to 35 cycles ≥ 10 cycles 6 to 24 cycles ≥ 10 cycles 35 cycles 24 cycles > 6 x burst length > 25 ms 2000 2000 For bursts greater than a minimum gap time in the data stream is needed of Maximum number of continuous short bursts/second MCIR code Preferred Yes RCMM code Preferred Yes XMP-1, XMP-2 code Suppression of interference from fluorescent lamps Preferred Yes Mild and complex disturbance patterns are suppressed (example: signal pattern of Fig. 13 and 14) Critical disturbance patterns are suppressed, e.g. highly dimmed LCDs Note • For data formats with long bursts (more than 10 carrier cycles) please see the datasheet for TSOP372..H, TSOP374..H. Rev. 1.5, 10-Nov-15 5 Document Number: 82643 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP373..H, TSOP375..H www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 4 x 0.75 = 3 (0.7) (0.3) (0.4) (2.85) (1.8) (0.95) 0.475 0.55 (0.3) (0.3) 0.75 ± 0.05 (2) Pins connected internally. It is not necessary to connect externally. 1.5 Pinning from Topview GND 1 ± 0.2 3 7 (2) 6 (GND) 8 GND 0.55 (8 x) 0.35 ± 0.05 Allowed offset outer edge of shield to solder pads of molded device ± 0.1 mm 4 5 (2) (4.3) (0.45) (4.3) 4 x 0.75 = 3 (2.75) Marking area Drawing-No.: 6.550-5316.01-4 Issue: 2; 12.02.14 3 (2) (0.8) (3 x) (1.2) (2.9) (1) Pin 1 identification 2 (2) Proposed pad layout from component side (dim. for reference only) 4.3 ± 0.2 (1.7) (1) 1 Vs (3.25)(1) (Vs) Out 4.3 ± 0.2 (GND) All dimensions in mm Not indicated tolerances ± 0.1 (1) optically effective area (GND) 0.15 technical drawings according to DIN specifications (3 x) (0.35) Rev. 1.5, 10-Nov-15 6 Document Number: 82643 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP373..H, TSOP375..H www.vishay.com Vishay Semiconductors ASSEMBLY INSTRUCTIONS Reflow Soldering Manual Soldering • Reflow soldering must be done within 168 h while stored under a max. temperature of 30 °C, 60 % RH after opening the dry pack envelope • Use a soldering iron of 25 W or less. Adjust the temperature of the soldering iron below 300 °C • Set the furnace temperatures for pre-heating and heating in accordance with the reflow temperature profile as shown in the diagram. Exercise extreme care to keep the maximum temperature below 260 °C. The temperature shown in the profile means the temperature at the device surface. Since there is a temperature difference between the component and the circuit board, it should be verified that the temperature of the device is accurately being measured • Handle products only after the temperature has cooled off • Finish soldering within 3 s • Handling after reflow should be done only after the work surface has been cooled off VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE 300 max. 260 °C 245 °C 255 °C 240 °C 217 °C 250 T (°C) 200 max. 20 s 150 max. 100 s max. 120 s 100 max. Ramp Up 3 °C/s max. Ramp Down 6 °C/s 50 0 0 19800 50 100 150 t (s) 200 250 300 max. 2 cycles allowed ORDERING INFORMATION ORDERING CODE TSOP37..HTT1 TSOP37..HTT2 PACKAGING Tape and reel VOLUME (1) MOQ: 1500 pcs MOQ: 5000 pcs REMARKS 3.95 mm x 3.95 mm x 0.75 mm Note (1) MOQ: minimum order quantity Rev. 1.5, 10-Nov-15 7 Document Number: 82643 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP373..H, TSOP375..H www.vishay.com Vishay Semiconductors TAPING VERSION TSOP37..H DIMENSIONS in millimeters Tape and Reel dimensions: Reel size "Y" X Unreel direction 2± Ø 60 min. GS 08 Ø 180 ± 2 = 1500 pcs. GS 18 Ø 330 ± 2 = 5000 pcs. Tape position coming out from reel ØY 0.5 Not indicated tolerances ± 0.1 Ø 21 ± 0.8 Ø 13 ± 0.2 Label posted here (12.4) 18.4 max. Parts mounted Empty leader 400 mm min. 100 mm min. with cover tape Leader and trailer tape: Empty trailer 200 mm min. Direction of pulling out Technical drawings according to DIN specifications (Ø 1.5) (2) (5.5) (0.3) (4) Drawing-No.: 9.700-5380.01-4 Issue: 1; 28.10.13 Reel dimensions and tape Rev. 1.5, 10-Nov-15 (12) (8) (1.75) X 2:1 8 Document Number: 82643 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP373..H, TSOP375..H www.vishay.com Vishay Semiconductors LABEL Standard bar code labels for finished goods The standard bar code labels are product labels and used for identification of goods. The finished goods are packed in final packing area. The standard packing units are labeled with standard bar code labels before transported as finished goods to warehouses. The labels are on each packing unit and contain Vishay Semiconductor GmbH specific data. VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods) PLAIN WRITING ABBREVIATION LENGTH Item-description - 18 Item-number INO 8 Selection-code SEL 3 BATCH 10 Data-code COD 3 (YWW) Plant-code PTC 2 Quantity QTY 8 Accepted by ACC - Packed by PCK - LOT-/serial-number Mixed code indicator Origin Long bar code top MIXED CODE - xxxxxxx+ Company logo Type Length Item-number N 8 Plant-code N 2 Sequence-number X 3 Quantity N 8 Total length - 21 Short bar code bottom Type Length Selection-code X 3 Data-code N 3 Batch-number X 10 Filter - 1 Total length - 17 DRY PACKING RECOMMENDED METHOD OF STORAGE The reel is packed in an anti-humidity bag to protect the devices from absorbing moisture during transportation and storage. Dry box storage is recommended as soon as the aluminum bag has been opened to prevent moisture absorption. The following conditions should be observed, if dry boxes are not available: Aluminum bag • Storage temperature 10 °C to 30 °C • Storage humidity ≤ 60 % RH max. Label After more than 168 h under these conditions moisture content will be too high for reflow soldering. In case of moisture absorption, the devices will recover to the former condition by drying under the following condition: Reel 192 h at 40 °C + 5 °C / - 0 °C and < 5 % RH (dry air / nitrogen) or 15973 96 h at 60 °C + 5 °C and < 5 % RH for all device containers or FINAL PACKING 24 h at 125 °C + 5 °C not suitable for reel or tubes. The sealed reel is packed into a cardboard box. A secondary cardboard box is used for shipping purposes. Rev. 1.5, 10-Nov-15 An EIA JEDEC® standard J-STD-020 level 3 label is included on all dry bags. 9 Document Number: 82643 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP373..H, TSOP375..H www.vishay.com Vishay Semiconductors LEVEL Caution This bag contains MOISTURE-SENSITIVE DEVICES VISHAY SEMICONDUCTORS STANDARD BAR CODE LABELS 3 The Vishay Semiconductors standard bar code labels are printed at final packing areas. The labels are on each packing unit and contain Vishay Semiconductors specific data. If blank, see adjacent bar code label 1. Calculated shelf life in sealed bag: 12 months at <40°C and <90% relative humidity (RH) 260 2. Peak package body temperature:_______________________°C If blank, see adjacent bar code label BAR CODE PRODUCT LABEL (example) 3. After bag is opened, devices that will be subjected to reflow solder or other high temperature process must be 168 a) Mounted within:___________________hours of factory conditions If blank, see adjacent bar code label ≤30°C/60% RH, or b) Stored per J-STD-033 4. Devices require bake, before mounting, if: a) Humidity Indicator Card reads > 10% for level 2a - 5a devices or >60% for level 2 devices when read at 23±5°C b) 3a or 3b are not met 5. If baking is required, refer to IPC/JEDEC J-STD-033 for bake procedure 22178 Bag Seal Date:_________________________________________ If blank, see adjacent bar code label Note: Level and body temperature defined by IPC/JEDEC J-STD-020 22650 EIA JEDEC standard J-STD-020 level 3 label is included on all dry bags ESD PRECAUTION Proper storage and handling procedures should be followed to prevent ESD damage to the devices especially when they are removed from the antistatic shielding bag. Electrostatic sensitive devices warning labels are on the packaging. Rev. 1.5, 10-Nov-15 10 Document Number: 82643 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000