TSMP6000 www.vishay.com Vishay Semiconductors IR Sensor Module for Remote Control Systems FEATURES • Photo detector and preamplifier in one package • AC coupled response from 20 kHz to 60 kHz, all data formats • Improved shielding disturbance against electrical field • TTL and CMOS compatibility 1 2 3 4 • Output active low • Supply voltage 2.5 V to 5.5 V, typically the device works in the range between 2.0 V and 5.5 V 16797 • Carrier out signal for code learning functions • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 MECHANICAL DATA Pinning: 1 = GND, 2 = N.C., 3 = VS, 4 = OUT DESCRIPTION ORDERING CODE The TSMP6000 is a miniaturized sensor for receiving various kinds of modulated IR signals. A PIN diode and preamplifier are assembled on a lead frame, the epoxy package is designed as an IR filter. The modulated output signal, carrier out, can be used for code learning applications. Taping: TSMP6000TT - top view taped TSMP6000TR - side view taped This component has not been qualified according to automotive specifications. PARTS TABLE Carrier frequency 20 kHz to 60 kHz TSMP6000 Package Panhead Pinning 1 = GND, 2 = N.C., 3 = VS, 4 = OUT Dimensions (mm) 7.5 W x 5.3 H x 4.0 D Mounting SMD Application Code learning BLOCK DIAGRAM APPLICATION CIRCUIT 19750-2 Circuit 3 VS 4 Carrier out TIA Amp V S Transmitter TSMPxxxx with C1 = TSALxxxx 4.7 µF Signal shaping OUT GND R1 = 100 Ω R2 = 4.7 kΩ + VS µC VO GND 1 GND R1 + C1 recommended to suppress power supply disturbances. R2 recommended to get faster slopes and a correct high level of the output pulses. 19746-1 Rev. 1.5, 14-Apr-16 1 Document Number: 82620 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSMP6000 www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER SYMBOL VALUE UNIT Supply voltage (pin 3) TEST CONDITION VS -0.3 to +6 V Output voltage (pin 4) VO -0.3 to (VS + 0.3) V Output current (pin 4) IO 5 mA Tj 100 °C Storage temperature range Junction temperature Tstg -25 to +85 °C Operating temperature range Tamb -25 to +85 °C Note • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability. ELECTRICAL AND OPTICAL CHARACTERISTICS CARRIER OUT (Tamb = 25 °C, unless otherwise specified, VS = 3 V) PARAMETER Supply current (pin 3) TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Ev = 0 ISD 0.55 0.7 0.9 mA VS 2.5 - 5.5 V d - 5 - m Supply voltage Ev = 0, test signal see fig. 1, IR diode TSAL6200, IF = 400 mA Transmission distance IOSL = 0.5 mA, test signal see fig. 1 VOSL - - 250 mV Minimum irradiance Output voltage low (pin 4) VS = 3 V, (20 kHz to 60 kHz) Ee min. - 12 25 mW/m2 Maximum irradiance test signal see fig. 1, (20 kHz to 60 kHz) Ee max. 50 80 - W/m2 Angle of half transmission distance ϕ1/2 - ± 50 - deg fC = 20 kHz to 60 kHz, Ee = 25 mW/m2 to 50 W/m2, testsignal see fig. 1, BER ≤ 2% N carrier pulses Directivity Output accuracy input burst input burst input burst length length length -1 cycle +1 cycle counts TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) Carrier cycle (26.3 μs in case of 38 kHz) Optical burst (input signal) Delay time td Output voltage Fig. 1 - Testsignal Rev. 1.5, 14-Apr-16 2 Document Number: 82620 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSMP6000 www.vishay.com Vishay Semiconductors 0° S(λ)rel - Relative Spectral Sensitivity 1.0 10° 20° 30° 0.9 0.8 0.7 40° 0.6 1.0 0.5 0.9 50° 0.8 60° 0.4 0.3 70° 0.2 0.7 80° 0.1 0 700 750 800 850 900 950 1000 1050 1100 0.6 λ - Wavelength (nm) 20431 Fig. 2 - Relative Spectral Sensitivity vs. Wavelength 0.4 0.2 0 0.2 0.4 0.6 d rel - Relative Transmission Distance 16801 Fig. 3 - Horizontal Directivity PACKAGE DIMENSIONS in millimeters 7.5 Pick and place area. TT taping 7.2 (1.5) 2.8 2.2 5.3 A 1 4 0.5 ± 0.15 0.1 (1.4) 0.3 4x 0.1 1.27 2.9 3 x 1.27 = 3.81 4 0.4 A 5.51 Not indicated tolerances ± 0.3 Pick and place area. TR taping technical drawings according to DIN specifications 2.6 Footprint 2.35 3 x 1.27 = 3.81 0.9 2.2 1.27 R 1.7 Drawing-No.: 6.544-5341.01-4 Issue: 8; 02.09.09 16776 Rev. 1.5, 14-Apr-16 3 Document Number: 82620 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSMP6000 www.vishay.com Vishay Semiconductors ASSEMBLY INSTRUCTIONS Reflow Soldering Manual Soldering • Reflow soldering must be done within 72 h while stored under a max. temperature of 30 °C, 60 % RH after opening the dry pack envelope • Use a soldering iron of 25 W or less. Adjust the temperature of the soldering iron below 300 °C • Set the furnace temperatures for pre-heating and heating in accordance with the reflow temperature profile as shown in the diagram. Exercise extreme care to keep the maximum temperature below 260 °C. The temperature shown in the profile means the temperature at the device surface. Since there is a temperature difference between the component and the circuit board, it should be verified that the temperature of the device is accurately being measured • Handle products only after the temperature has cooled off • Finish soldering within 3 s • Handling after reflow should be done only after the work surface has been cooled off VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE 300 max. 260 °C 245 °C 255 °C 240 °C 217 °C 250 T (°C) 200 max. 20 s 150 max. 100 s max. 120 s 100 max. Ramp Up 3 °C/s max. Ramp Down 6 °C/s 50 0 0 19800 Rev. 1.5, 14-Apr-16 50 100 150 t (s) 4 200 250 300 max. 2 cycles allowed Document Number: 82620 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSMP6000 www.vishay.com Vishay Semiconductors TAPING VERSION TSMP..TT DIMENSIONS in millimeters 16584 Rev. 1.5, 14-Apr-16 5 Document Number: 82620 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSMP6000 www.vishay.com Vishay Semiconductors TAPING VERSION TSMP..TR DIMENSIONS in millimeters 16585 Rev. 1.5, 14-Apr-16 6 Document Number: 82620 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSMP6000 www.vishay.com Vishay Semiconductors REEL DIMENSIONS in millimeters 16734 LEADER AND TRAILER DIMENSIONS in millimeters Trailer no devices Leader devices no devices End Start min. 200 min. 400 96 11818 COVER TAPE PEEL STRENGTH LABEL According to DIN EN 60286-3 Standard bar code labels for finished goods 0.1 N to 1.3 N The standard bar code labels are product labels and used for identification of goods. The finished goods are packed in final packing area. The standard packing units are labeled with standard bar code labels before transported as finished goods to warehouses. The labels are on each packing unit and contain Vishay Semiconductor GmbH specific data. 300 mm/min. ± 10 mm/min. 165° to 180° peel angle Rev. 1.5, 14-Apr-16 7 Document Number: 82620 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSMP6000 www.vishay.com Vishay Semiconductors VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods) PLAIN WRITTING Item-description Item-number Selection-code LOT-/serial-number Data-code Plant-code Quantity Accepted by Packed by Mixed code indicator Origin LONG BAR CODE TOP Item-number Plant-code Sequence-number Quantity Total length SHORT BAR CODE BOTTOM Selection-code Data-code Batch-number Filter Total length ABBREVIATION INO SEL BATCH COD PTC QTY ACC PCK MIXED CODE xxxxxxx+ TYPE N N X N TYPE X N X - DRY PACKING LENGTH 18 8 3 10 3 (YWW) 2 8 Company logo LENGTH 8 2 3 8 21 LENGTH 3 3 10 1 17 In case of moisture absorption, the devices will recover to the former condition by drying under the following condition: The reel is packed in an anti-humidity bag to protect the devices from absorbing moisture during transportation and storage. 192 h at 40 °C + 5 °C / - 0 °C and < 5 % RH (dry air / nitrogen) or 96 h at 60 °C + 5 °C and < 5 % RH for all device containers or 24 h at 125 °C + 5 °C not suitable for reel or tubes. Aluminum bag Label An EIA JEDEC® standard J-STD-020 level 4 label is included on all dry bags. LEVEL CAUTION Reel This bag contains MOISTURE-SENSITIVE DEVICES 4 15973 1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 % relative humidity (RH) FINAL PACKING The sealed reel is packed into a cardboard box. A secondary cardboard box is used for shipping purposes. 2. After this bag is opened, devices that will be subjected to soldering reflow or equivalent processing (peak package body temp. 260 °C) must be 2a. Mounted within 72 hours at factory condition of < 30 °C/60 % RH or 2b. Stored at < 5 % RH RECOMMENDED METHOD OF STORAGE 3. Devices require baking befor mounting if: Humidity Indicator Card is > 10 % when read at 23 °C ± 5 °C or 2a. or 2b. are not met. Dry box storage is recommended as soon as the aluminum bag has been opened to prevent moisture absorption. The following conditions should be observed, if dry boxes are not available: 4. If baking is required, devices may be baked for: 192 hours at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen) or 96 hours at 60 °C ± 5 °C and < 5 % RH for all device containers or 24 hours at 125 °C ± 5 °C not suitable for reels or tubes Bag Seal Date: (If blank, see barcode label) • Storage temperature 10 °C to 30 °C Note: Level and body temperature defined by EIA JEDEC Standard J-STD-020 • Storage humidity ≤ 60 % RH max. 22522 After more than 72 h under these conditions moisture content will be too high for reflow soldering. Rev. 1.5, 14-Apr-16 EIA JEDEC standard J-STD-020 level 4 label is included on all dry bags 8 Document Number: 82620 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSMP6000 www.vishay.com Vishay Semiconductors ESD PRECAUTION VISHAY SEMICONDUCTORS STANDARD BAR CODE LABELS Proper storage and handling procedures should be followed to prevent ESD damage to the devices especially when they are removed from the antistatic shielding bag. Electrostatic sensitive devices warning labels are on the packaging. The Vishay Semiconductors standard bar code labels are printed at final packing areas. The labels are on each packing unit and contain Vishay Semiconductors specific data. 22645 Rev. 1.5, 14-Apr-16 9 Document Number: 82620 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors Tape and Reel Standards for SMD IR Receiver Modules Vishay Semiconductor SMD IR receivers are packaged on tape and reel. The following specification is based on IEC publication 286, which takes the industrial requirements for automatic insertion into account. NUMBER OF COMPONENTS A. Panhead SMD: quantity per reel: TT, SMD top view package, 1190 pcs TR, SMD side view package, 1120 pcs Absolute maximum ratings, mechanical dimensions, optical and electrical characteristics for taped devices are identical to the basic catalog types and can be found in the specifications for untaped devices. B. Heimdall: quantity per reel: TT, Heimdall top view package, 2200 pcs TR, Heimdall side view package, 2300 pcs C. Heimdall without lens: quantity per reel: PACKAGING WTT, top view package, 2200 pcs The tapes of components are available on reels. Each reel is marked with labels which contain the following information: WTR, side view package, 2300 pcs D. Belobog: quantity per reel: - Vishay - Type TT1, 1800 pcs - Group TT2, 7000 pcs - Tape code, normally part of type name TR, not available in side view - Production code E. Belobog with shield: quantity per reel: - Quantity TT1, 1500 pcs TT2, 5000 pcs MISSING COMPONENTS Up to 3 consecutive components may be missing if the gap is followed by at least 6 components. A maximum of 0.5 % of the components per reel quantity may be missing. At least 5 empty positions are present at the start and the end of the tape to enable tape insertion. ORDER DESIGNATION The type designation of the device is extended by TT or TT1 for top view or TR for side view. Example: TSOP6238TR (reel packing) Tensile strength of the tape: > 15 N TSOP75238TR (reel packing) TSOP75338WTT (reel packing) TSOP57438TT1 (reel packing) TSOP57238HTT1 (reel packing) Rev. 2.1, 13-Oct-15 1 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors REEL DIMENSIONS FOR PANHEAD SMD AND HEIMDALL in millimeters 16734 Note • The body structure of the reel can vary Rev. 2.1, 13-Oct-15 2 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TT (TOP VIEW) DIMENSIONS in millimeters A. Panhead SMD (TSOP36...TT, TSSP....TT, TSOP6...TT) 16584 Rev. 2.1, 13-Oct-15 3 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TT (TOP VIEW) DIMENSIONS in millimeters 3.65 0.3 B. Heimdall SMD (TSOP75...TT, TSOP77...TT, TSSP77...TT) 16 1.75 7.5 Ø 1.5 4 8 Direction of feed 2 Ø 1.5 technical drawings according to DIN specifications Drawing-No.: 9.700-5338.01-4 Issue: 4; 12.06.13 Rev. 2.1, 13-Oct-15 4 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TT (TOP VIEW) DIMENSIONS in millimeters 3 0.3 C. Heimdall SMD without lens (TSOP75...WTT, TSOP77...WTT, TSSP77...WTT) 16 1.75 7.5 Ø 1.5 4 Direction of feed 8 2 Ø 1.5 min. technical drawings according to DIN specifications Drawing-No.: 9.700-5341.01-4 Issue: 3; 06.10.15 Rev. 2.1, 13-Oct-15 5 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TT1, TSOP..TT2 (TOP VIEW) DIMENSIONS in millimeters D. Belobog (TSOP37...TT1, TSOP37...TT2, TSOP57...TT1, TSOP57...TT2) Tape and reel dimensions: Unreel direction TT1 Ø 180 ± 2 = 1800 pcs. TT2 Ø 330 ± 2 = 7000 pcs. Tape position coming out from reel 2± Ø 60 min. Reel size "Y" ØY 0.5 Ø 21 ± 0.8 Ø 13 ± 0.2 Label posted here (12.4) 18.4 max. Empty leader 400 mm min. Parts mounted 100 mm min. with cover tape Leader and trailer tape: Empty trailer 200 mm min. Direction of pulling out Technical drawings according to DIN specifications (Ø 1.5) (2) (5.5) (0.3) (4) Drawing-No.: 9.700-5347.01-4 Issue: 1; 14.11.11 Rev. 2.1, 13-Oct-15 12 ± 0.3 (8) (1.2) (1.75) X 2:1 Not indicated tolerances ± 0.1 6 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TT1, TSOP..TT2 (TOP VIEW) DIMENSIONS in millimeters E. Belobog with shield (TSOP37...HTT1, TSOP37...HTT2, TSOP57...HTT1, TSOP57...HTT2) Tape and Reel dimensions: Reel size "Y" X Unreel direction 2± Ø 60 min. GS 08 Ø 180 ± 2 = 1500 pcs. GS 18 Ø 330 ± 2 = 5000 pcs. Tape position coming out from reel ØY 0.5 Not indicated tolerances ± 0.1 Ø 21 ± 0.8 Ø 13 ± 0.2 Label posted here (12.4) 18.4 max. Parts mounted Empty leader 400 mm min. 100 mm min. with cover tape Leader and trailer tape: Empty trailer 200 mm min. Direction of pulling out Technical drawings according to DIN specifications (Ø 1.5) (2) (5.5) (0.3) (4) Drawing-No.: 9.700-5380.01-4 Issue: 1; 28.10.13 Reel dimensions and tape Rev. 2.1, 13-Oct-15 (12) (8) (1.75) X 2:1 7 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TR (SIDE VIEW) DIMENSIONS in millimeters A. Panhead SMD (TSOP36...TR, TSSP6...TR, TSOP6...TR) 16585 Rev. 2.1, 13-Oct-15 8 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TR (SIDE VIEW) DIMENSIONS in millimeters 0.3 3.6 B. Heimdall SMD (TSOP75..., TSOP77..., TSSP7....) 16 7.5 1.75 1.34 ref. Ø 1.5 4 Direction of feed 8 2 Ø 1.5 min. technical drawings according to DIN specifications Drawing-No.: 9.700-5337.01-4 Issue: 2; 06.10.15 Rev. 2.1, 13-Oct-15 9 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors TAPING VERSION TSOP..TR (SIDE VIEW) DIMENSIONS in millimeters 3.6 0.3 C. Heimdall SMD without lens (TSOP75...WTR, TSOP77...WTR, TSSP...WTR) 16 1.75 7.5 Ø 1.5 4 Direction of feed 8 2 Ø 1.5 technical drawings according to DIN specifications Drawing-No.: 9.700-5342.01-4 Issue: 2; 12.06.13 Rev. 2.1, 13-Oct-15 10 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors LEADER AND TRAILER DIMENSIONS in millimeters Trailer no devices Leader devices no devices End Start min. 200 min. 400 96 11818 COVER TAPE REEL STRENGTH LABEL According to DIN EN 60286-3 Standard bar code labels for finished goods 0.1 N to 1.3 N The standard bar code labels are product labels and used for identification of goods. The finished goods are packed in final packing area. The standard packing units are labeled with standard bar code labels before transported as finished goods to warehouses. The labels are on each packing unit and contain Vishay Semiconductor GmbH specific data. 300 mm/min. ± 10 mm/min. 165° to 180° peel angle VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods) PLAIN WRITING ABBREVIATION LENGTH Item-description - 18 INO 8 Item-number Selection-code SEL 3 BATCH 10 Data-code COD 3 (YWW) Plant-code PTC 2 Quantity QTY 8 Accepted by ACC - Packed by PCK - MIXED CODE - xxxxxxx+ Company logo TYPE LENGTH LOT-/serial-number Mixed code indicator Origin LONG BAR CODE TOP Item-number N 8 Plant-code N 2 Sequence-number X 3 Quantity N 8 Total length - 21 TYPE LENGTH Selection-code X 3 Data-code N 3 Batch-number X 10 Filter - 1 Total length - 17 SHORT BAR CODE TOP Rev. 2.1, 13-Oct-15 11 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SMD Tape and Reel www.vishay.com Vishay Semiconductors DRY PACKAGING The reel is packed in an anti-humidity bag to protect the devices from absorbing moisture during transportation and storage. LEVEL CAUTION This bag contains MOISTURE-SENSITIVE DEVICES Aluminum bag 4 1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 % relative humidity (RH) 2. After this bag is opened, devices that will be subjected to soldering reflow or equivalent processing (peak package body temp. 260 °C) must be 2a. Mounted within 72 hours at factory condition of < 30 °C/60 % RH or 2b. Stored at < 5 % RH Label 3. Devices require baking befor mounting if: Humidity Indicator Card is > 10 % when read at 23 °C ± 5 °C or 2a. or 2b. are not met. 4. If baking is required, devices may be baked for: 192 hours at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen) or 96 hours at 60 °C ± 5 °C and < 5 % RH for all device containers or 24 hours at 125 °C ± 5 °C not suitable for reels or tubes Reel Bag Seal Date: (If blank, see barcode label) 15973 Note: Level and body temperature defined by EIA JEDEC Standard J-STD-020 22522 RECOMMENDED METHOD OF STORAGE EIA JEDEC standard JSTD-020 level 4 label is included on all dry bags Dry box storage is recommended as soon as the aluminum bag has been opened to prevent moisture absorption. The following conditions should be observed, if dry boxes are not available: ESD PRECAUTION Proper storage and handling procedures should be followed to prevent ESD damage to the devices especially when they are removed from the antistatic shielding bag. Electrostatic sensitive devices warning labels are on the packaging. • Storage temperature 10 °C to 30 °C • Storage humidity 60 % RH max. After more than 72 h under these conditions moisture content will be too high for reflow soldering. VISHAY SEMICONDUCTORS STANDARD BAR CODE LABELS In case of moisture absorption, the devices will recover to the former condition by drying under the following condition: The Vishay Semiconductors standard bar code labels are printed at final packing areas. The labels are on each packing unit and contain Vishay Semiconductors specific data. 192 h at 40 °C + 5 °C / - 0 °C and < 5 % RH (dry air / nitrogen) or 96 h at 60 °C + 5 °C and < 5 % RH for all device containers or 24 h at 125 °C + 5 °C not suitable for reel or tubes. An EIA JEDEC® standard JSTD-020 level 4 label is included on all dry bags. 16962 OUTER PACKAGING The sealed reel is packed into a pizza box. CARTON BOX DIMENSIONS in millimeters Length Thickness Width 22127 Pizza Box (SMD and Heimdall) (Taping in reels) Rev. 2.1, 13-Oct-15 THICKNESS WIDTH LENGTH 50 340 340 12 Document Number: 80125 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000