CS44 Datasheet

CS44
www.vishay.com
Vishay Sfernice
High Value (up to 100 M) Wirebondable
1 mm2 Thin Film Chip Resistors
FEATURES
• Small size 40 mil x 40 mil (1 mm x 1 mm)
• Very high ohmic value up to 100 M
• Good stability 0.1 % (2000 h, rated power at
+ 70 °C)
• Aluminum or gold terminations
• Wirebondable
• Material categorization: For definitions of
compliance please see www.vishay.com/doc?99912
Chromium silicon thin film is very well suited to produce
high density and high ohmic value resistor chips. These
high ohmic value chip resistors are available with improved
performances and size when compared to thick film
counterparts.
SCHEMATIC
R
STANDARD ELECTRICAL SPECIFICATIONS
MODEL
SIZE
RESISTANCE
RANGE

RATED POWER
P70 °C
W
LIMITING
ELEMENT
VOLTAGE
V
TOLERANCE
±%
TEMPERATURE
COEFFICIENT
± ppm/°C
CS44
0404
400K to 100M
0.380
100
0.5, 1.0, 2.0, 5.0
50 (1), 100
Note
(1) On request
CLIMATIC SPECIFICATIONS
MECHANICAL SPECIFICATIONS
Operating temperature range
- 55 °C to + 155 °C
Resistive element
Storage temperature range
- 55 °C to + 155 °C
Passivation
Substrate material
Bonding pads
Chromium Silicon
Silicon Nitride
Silicon (consult Vishay for Al2O3)
Aluminum or gold
TECHNICAL SPECIFICATIONS
TEST
MATERIAL
Stability
Limiting voltage
Noise
Thermal EMF
Shelf life stability
Note
• Rated voltage =
Revision: 26-Mar-13
SPECIFICATIONS
CONDITIONS
PASSIVATED CHROMIUM SILICON
± 0.1 % typical, ± 0.2 maximum
2000 h at + 70 °C at Pn
100 VDC
Higher on Al2O3
< - 20 dB typical
MIL-STD-202 method 308
< 0.01 μV/°C
200 ppm
1 year at + 25 °C
 Power rating x Resis tan ce value  or limiting voltage, whichever is lower
Document Number: 60114
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CS44
www.vishay.com
Vishay Sfernice
DIMENSIONS
DIMENSION
INCHES
MILLIMETERS
A
0.043 ± 0.002
1.09 ± 0.05
B
0.043 ± 0.002
1.09 ± 0.05
C
0.004
0.10
D
0.004
0.10
E
0.015
0.40 max.
B
A
C
E
D
GLOBAL PART NUMBER INFORMATION
New Global Part Numbering: CS44-100MJ0099
C
S
4
GLOBAL MODEL
Revision: 26-Mar-13
4
-
1
0
0
M
J
0
0
9
VALUE
TOLERANCE
TERMINATIONS
OPTION
Decimal
K or M
D = ± 0.5 %
F = ± 1.0 %
G = ± 2.0 %
J = ± 5.0 %
Blank = Aluminum
G = Gold
Leave blank
if no option
9
Document Number: 60114
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000