CRAS0606, CRAS0612, CRAE0612 www.vishay.com Vishay Draloric Thick Film Chip Resistor Array, Different Values FEATURES • Different values (CRAS0606 model) or two pairs of values (CRAS0612 / CRAE0612 model) • Convex terminal array available with either scalloped corners (version E) or square corners (version S) • AEC-Q200 qualified • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 The thick film chip resistor arrays, different values series combine the reliability of thick film chip resistor products with the advantages of chip resistor arrays. The small package enables the design of high density circuits with reduced assemblies’ costs. Two different resistor values or two resistor pairs are available. APPLICATIONS • Voltage divider • Feedback circuits • DC/DC converters • External circuits of operational amplifiers TECHNICAL SPECIFICATIONS DESCRIPTION EIA size Metric size code Configuration, isolated CRAS0606 CRAS0612, CRAE0612 0606 0612 RR1616M RR1632M 2 x 0603 4 x 0603 DF TP Design: Different values (DF) Two pairs of values (TP) 10 to 1 M (2) Resistance range Resistance tolerance ± 1 %; ± 5 % Temperature coefficient ± 100 ppm/K; ± 200 ppm/K Rated dissipation, P70 (1) Element 0.063 W 0.063 W Package 0.125 W 0.25 W Operating voltage, Umax. ACRMS/DC Permissible film temperature, F max. 50 V (1) 155 °C Operating temperature range -55 °C to +155 °C Max. resistance change at P70 for resistance range, |R/R| after: 1000 h 1.0 % 8000 h 2.0 % Permissible voltage against ambient (insulation): 1 min, Uins 100 V Notes (1) Please refer to APPLICATION INFORMATION below. (2) Resistance values to be selected from E24 + E96 (± 1 % tolerance) and E24 (± 5 % tolerance). Revision: 01-Jun-16 Document Number: 31102 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CRAS0606, CRAS0612, CRAE0612 www.vishay.com Vishay Draloric APPLICATION INFORMATION When the resistor dissipates power, a temperature rise above the ambient temperature occurs, dependent on the thermal resistance of the assembled resistor together with the printed circuit board. The rated dissipation applies only if the permitted film temperature is not exceeded. These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime. CIRCUITS 4 8 3 R1 R2 7 R1 6 R2 5 R3 R4 Pin 1 2 3 4 CRAS0612, CRAE0612 Pin 1 2 CRAS0606 Marking on CRAS0606: pin 1 is marked. DESIGN CRAS0606 TP CRAS0612, CRAE0612 R1 = R4 > R2 = R3 DF R1 > R2 Revision: 01-Jun-16 Document Number: 31102 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CRAS0606, CRAS0612, CRAE0612 www.vishay.com Vishay Draloric PART NUMBER AND PRODUCT DESCRIPTION PART NUMBER: CRASA10K0F1K00TA C R A S A 1 0 K 0 F 1 K 0 0 T A TYPE TERMINAL SIZE RESISTANCE (1) ACCURACY GRADE (2) RESISTANCE (1) PACKAGING SPECIAL CRA S = square corners E = scalloped corners N = 0606 A = 0612 R = decimal K = thousand M = million Tolerance and TCR F J R = decimal K = thousand M = million TA TC Up to 2 digits PRODUCT DESCRIPTION: CRAS0612 10K 1% 1K0 RT1 e3 CRA S 0612 10K 1% 1K0 RT1 e3 TYPE TERMINAL SIZE RESISTANCE R1, R4 (1) ACCURACY GRADE (2) RESISTANCE R2, R3 (1) PACKAGING LEAD (Pb)- FREE CRA = thick film chip array S = square corners E = scalloped corners 0606 0612 10R = 10 10K = 10 k 1M = 1 M Tolerance and TCR 1% 5% 10R = 10 10K = 10 k 1M = 1M RT1 RT6 e3 = pure tin termination finish Notes (1) R = R R = R 1 4 2 3 (2) Please refer to the table TEMPERATURE COEFFICIENT AND RESISTANCE RANGE TEMPERATURE COEFFICIENT AND RESISTANCE RANGE TYPE / SIZE ACCURACY GRADE TCR TOLERANCE RESISTANCE F ± 100 ppm/K ±1% 10 to 1 M J ± 200 ppm/K ±5% 10 to 1 M CRAS0606 CRAS0612 CRAE0612 PACKAGING TYPE / SIZE CODE QUANTITY CRAS0606 CRAS0612 CRAE0612 TA = RT1 5000 Revision: 01-Jun-16 TC = RT6 20 000 PACKAGING STYLE WIDTH PITCH Paper tape acc. to IEC 60286-3, Type 1a 8 mm 4 mm PACKAGING DIMENSIONS Ø 180 mm/7" Ø 330 mm/13" Document Number: 31102 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CRAS0606, CRAS0612, CRAE0612 www.vishay.com Vishay Draloric DIMENSIONS CRAS0606 CRAS0612 CRAE0612 L (mm) W (mm) H (mm) P (mm) A1 (mm) A (mm) B (mm) B* (mm) MASS (mg) CRAS0606 1.6 ± 0.15 1.5 ± 0.15 0.5 ± 0.1 - 0.61 ± 0.15 - 0.3 ± 0.15 0.3 ± 0.15 3.6 CRAS0612 CRAE0612 3.2 ± 0.15 1.5 ± 0.15 0.5 ± 0.1 0.8 ± 0.1 0.61 ± 0.15 0.38 ± 0.15 0.3 ± 0.15 0.3 ± 0.15 6.6 TYPE PATTERN STYLES FOR RESISTOR ARRAY I X U I X Y Y G Pin 1 Z G 0.1 Pin 1 P Dimensions in mm limits for solder resist Z 0.1 G (mm) Y (mm) X (mm) U (mm) Z (mm) I (mm) P (mm) CRAS0606 0.8 1.15 0.64 - 3.1 0.36 - CRAS0612 CRAE0612 0.8 1.15 0.64 0.5 3.1 0.36 0.8 TYPE Revision: 01-Jun-16 Document Number: 31102 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CRAS0606, CRAS0612, CRAE0612 www.vishay.com DESCRIPTION The production of the components is strictly controlled and follows an extensive set of instructions established for reproducibility. A cermet film layer and a glass-over are deposited on a high grade (AI2O3) ceramic substrate using a mask to separate the adjacent resistors and conditioned to achieve the desired temperature coefficient. Specially designed inner contacts are realized on both sides. A special laser is used to achieve the target value by smoothly fine trimming the resistive layer without damaging the ceramics. The resistor elements are covered by a protective coating designed for electrical, mechanical and climatic protection. The terminations receive a final pure tin on nickel plating. The result of the determined production is verified by an extensive testing procedure and optical inspection performed on 100 % of the individual chip resistors. Only accepted products are laid directly into the paper tape in accordance with IEC 60286-3, Type 1a (1). ASSEMBLY The resistors are suitable for processing on automatic SMD assembly systems. They are suitable for automatic soldering using wave, reflow or vapor phase as shown in IEC 61760-1. The encapsulation is resistant to all cleaning solvents commonly used in the electronics industry, including alcohols, esters and aqueous solutions. The suitability of conformal coatings potting compounds and their processes, if applied, shall be qualified by appropriate means to ensure the long-term stability of the whole system. Vishay Draloric The products do not contain any of the banned substances as per IEC 62474, GADSL, or the SVHC list, see www.vishay.com/how/leadfree. Hence the products fully comply with the following directives: • 2000/53/EC End-of-Life Vehicle Directive (ELV) and Annex II (ELV II) • 2011/65/EU Restriction of the Use of Hazardous Substances Directive (RoHS) with amendment 2015/863/EU • 2012/19/EU Waste Electrical and Electronic Equipment Directive (WEEE) Vishay pursues the elimination of conflict minerals from its supply chain, see the Conflict Minerals Policy at www.vishay.com/doc?49037. APPROVALS The resistors are qualified according to AEC-Q200. Where applicable, the resistors are tested in accordance with EN 140401-802 which refers to EN 60115-1, EN 60115-8 and the variety of environmental test procedures of the IEC 60068 (1) series. RELATED PRODUCTS For the thick film chip array with equal resistance values, please refer to CRA06E, CRA06S, Thick Film Chip Resistor Array datasheet (www.vishay.com/doc?31002). The resistors are RoHS-compliant, the pure tin plating provides compatibility with lead (Pb)-free and lead-containing soldering processes. Solderability is specified for 2 years after production or requalification. The permitted storage time is 20 years. The immunity of the plating against tin whisker growth has been proven under extensive testing. MATERIALS Vishay acknowledges the following systems for the regulation of hazardous substances: • IEC 62474, Material Declaration for Products of and for the Electrotechnical Industry, with the list of declarable substances given therein (2) • The Global Automotive Declarable Substance List (GADSL) (3) • The REACH regulation (1907/2006/EC) and the related list of substances with very high concern (SVHC) (4) for its supply chain Notes (1) The quoted IEC standards are also released as EN standards with the same number and identical contents. (2) The IEC 62474 list of declarable substances is maintained in a dedicated database, which is available at http://std.iec.ch/iec62474. (3) The Global Automotive Declarable Substance List (GADSL) is maintained by the American Chemistry Council and available at www.gadsl.org. (4) The SVHC list is maintained by the European Chemical Agency (ECHA) and available at http://echa.europa.eu/candidate-list-table. Revision: 01-Jun-16 Document Number: 31102 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CRAS0606, CRAS0612, CRAE0612 www.vishay.com Vishay Draloric FUNCTIONAL PERFORMANCE Derating 70 10000 0.3 CRAS0612, CRAE0612 0.25 1000 1st line 2nd line 2nd line P - Power Dissipation (W) Axis Title 0.35 0.2 0.15 CRAS0606 100 0.1 0.05 0 -50 50 0 100 10 150 ϑamb - Ambient Temperature (°C) 2nd line TESTS AND REQUIREMENTS All executed tests are carried out in accordance with the following specifications: The testing also covers most of the requirements specified by EIA/IS-703 and JIS-C-5201-1. EN 60115-1, generic specification The tests are carried out under standard atmospheric conditions in accordance with IEC 60068-1, 4.3, whereupon the following values are applied: EN 60115-8 specification (successor of EN 140400), sectional EN 140401-802, detail specification Temperature: 15 °C to 35 °C IEC 60068-2-xx, test methods Relative humidity: 25 % to 75 % The parameters stated in the Test Procedures and Requirements table are based on the required tests and permitted limits of EN 140401-802. The table presents only the most important tests, for the full test schedule refer to the documents listed above. However, some additional tests and a number of improvements against those minimum requirements have been included. Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar). A climatic category LCT / UCT / 56 is applied, defined by the lower category temperature (LCT), the upper category temperature (UCT), and the duration of exposure in the damp heat, steady state test (56 days). The components are mounted for testing on boards in accordance with EN 60115-8, 2.4.2 unless otherwise specified. TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2 (1) TEST METHOD TEST PROCEDURE Stability for product types: REQUIREMENTS PERMISSIBLE CHANGE (R) STABILITY CLASS 1 OR BETTER STABILITY CLASS 2 OR BETTER 10 to 1 M CRAS0606, CRAS0612, CRAE0612 4.5 - Resistance - ±1% ±5% 4.8 - Temperature coefficient (20 / -55 / 20) °C and (20 / 155 / 20) °C ± 100 ppm/K ± 200 ppm/K - Endurance at 70 °C U = P 70 x R Umax.; 1.5 h on; 0.5 h off; 70 °C; 1000 h 70 °C; 8000 h ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) ± (2 % R + 0.1) ± (4 % R + 0.1 ) 78 (Cab) Damp heat, steady state (40 ± 2) °C; (93 ± 3) % RH; 56 days 4.25.1 4.24 Revision: 01-Jun-16 ± (1 % R + 0.05 ) Document Number: 31102 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CRAS0606, CRAS0612, CRAE0612 www.vishay.com Vishay Draloric TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2 (1) TEST METHOD TEST PROCEDURE Stability for product types: REQUIREMENTS PERMISSIBLE CHANGE (R) STABILITY CLASS 1 OR BETTER 10 to 1 M CRAS0606, CRAS0612, CRAE0612 4.23 - Climatic sequence: - 4.23.2 2 (Bb) Dry heat 125 °C; 16 h 4.23.3 30 (Db) Damp heat, cyclic 55 °C; 24 h; 90 % RH; 1 cycle ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) -55 °C; 2 h ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) Rapid change of temperature 30 min. at -55 °C; 30 min. at 125°C 1000 cycles ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) ± (2 % R + 0.05 ) ± (1 % R + 0.05 ) 4.23.4 1 (Ab) Cold -55 °C; 2 h 4.23.5 13 (M) Low air pressure 8.5 kPa; 2 h; (25 ± 10) °C 4.23.6 30 (Db) Damp heat, cyclic 55 °C; 24 h; 90 % RH; 5 cycles 4.23.7 - DC load 1 (Aa) Cold 4.19 14 (Na) U= P 70 x R Umax.; 1 min 4.13 - Short time overload (2) U = 2.5 x P 70 x R 2 x Umax.; whichever is less severe; 5s 4.40 - Electrostatic discharge (Human body model) (2) IEC 61340-3-1 3 pos. + 3 neg. discharges; 500 V 6 (Fc) Vibration, endurance by sweeping f = 10 Hz to 2000 Hz; x, y, z 1.5 mm; A 200 m/s2; 10 sweeps per axis 4.22 4.17 58 (Td) STABILITY CLASS 2 OR BETTER Solderability ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) Solder bath method; Sn60Pb40; non-activated flux; (235 ± 5) °C (2 ± 0.2) s Good tinning ( 95 % covered); no visible damage Solder bath method; Sn96.5Ag3Cu0.5 non-activated flux; (245 ± 5) °C (3 ± 0.3) s Good tinning (95 % covered); no visible damage 4.18 58 (Td) Resistance to soldering heat Solder bath method (260 ± 5) °C; (10 ± 1) s 4.29 45 (XA) Component solvent resistance Isopropyl alcohol; 50 °C; method 2 No visible damage 4.30 45 (XA) Solvent resistance of marking Isopropyl alcohol; 50 °C; method 1, toothbrush Marking legible, no visible damage 4.32 21 (Uu3) Shear (adhesion) 17.7 N No visible damage ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) 4.33 21 (Uu1) Substrate bending Depth 2 mm; 3 times No visible damage, no open circuit in bent position ± (0.25 % R + 0.05 ) 4.7 - Voltage proof U = 1.4 x Uins; 60 s No flashover or breakdown - Flammability, needle flame test IEC 60695-11-5 (1); 10 s No burning after 30 s 4.35 Notes (1) The quoted IEC standards are also released as EN standards with the same number and identical contents (2) For a single element Revision: 01-Jun-16 Document Number: 31102 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000