PCF8811 80 x 128 pixels matrix LCD driver Rev. 6 — 10 February 2015 Product data sheet 1. General description The PCF8811 is a low-power CMOS1 LCD controller and driver. It is designed to drive a graphic display of 80 rows and 128 columns or of 79 rows, 128 columns, and an icon row of 128 symbols. All necessary functions for the display are provided in a single chip, including on-chip generation of the LCD supply and bias voltages. Therefore only a minimum of external components are required and power consumption is low. The PCF8811 can interface microcontrollers via a parallel bus, serial bus, or I2C-bus interface. For a selection of NXP LCD graphic drivers, see Table 44 on page 85. 2. Features and benefits 1. Single-chip LCD controller and driver 80 row and 128 column outputs Display data RAM 80 128 bit 128 icons (in extended command set row 79 can be configured for displaying icons) Low power consumption; suitable for battery operated systems Interfaces: 8-bit parallel 3- or 4-line Serial Peripheral Interface (SPI) High-speed I2C-bus Configurable voltage multiplier generating LCD supply voltage VLCD; an external VLCD is also possible Linear temperature compensation of VLCD: 8 programmable temperature coefficients (extended command set) one fixed temperature coefficient which can be set as default by OTP programming (basic command set) Generation of intermediate LCD bias voltage Oscillator requires no external components OTP calibration for VLCD and accurate frame frequency External reset input pin External clock input possible Multiplex rate 1:16 to 1:80 selectable in steps of 8 when icon row is not used in steps of 16 when the icon row is used Logic supply voltage range VDD1 to VSS: 1.7 V to 3.3 V The definition of the abbreviations and acronyms used in this data sheet can be found in Section 24. PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver High-voltage multiplier supply voltage range VDD2, VDD3 to VSS: 1.8 V to 3.3 V Display supply voltage range VLCD to VSS: 3 V to 9 V Programmable bottom row pins mirroring; for compatibility with both Tape Carrier Packages (TCP) and Chip-On-Glass (COG) applications (extended command set) Status read, which allows for chip recognition and content checking of some registers Start address line which allows, for instance, the scrolling of the displayed image Programmable display RAM pointers for variable display sizes Slim chip layout, suited for COG applications Temperature range: Tamb = 40 C to +85 C CMOS compatible inputs 3. Applications Automotive displays Telecommunication equipment Portable instruments Point-of-sale terminals Consumer healthcare devices 4. Ordering information Table 1. Ordering information Type number Package Name Description Version PCF8811U/2DA/1 - chip with bumps in tray (not covered by Motif license agreement) - PCF8811MU/2DA/1 - chip with bumps in tray (sold under license from Motif) - PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 2 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 5. Block diagram 9'' 9'' 9'' 5WR5 &WR& 9''WLHRII 966WLHRII 52:'5,9(56 &2/801'5,9(56 %,$6 92/7$*( *(1(5$725 9/&',1 257+2*21$/ )81&7,21 *(1(5$725 '$7$ 352&(66,1* 966 966 9273352* 9/&'6(16( +,*+ 92/7$*( *(1(5$725 9/&'287 ',63/$<'$7$5$0 î%,76 7 5(6(7 5(6 26&,//$725 26& 7,0,1* *(1(5$725 7 7 $''5(66&2817(5 7 ',63/$< $''5(66 &2817(5 7 0)>@ &200$1' '(&2'(5 '6 3&) ,2%8))(5 3$5$//(/6(5,$/,&%86,17(5)$&( Fig 1. '% '% '%6$ '%6$ '% '%6'2 '%6&/. '%6'$7$ 6'$+ 6'$+287 6&/+6&( (5' 5::5 '& 36>@ (;7 926>@ PJZ Block diagram of PCF8811 PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 3 of 94 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors PCF8811 0) 26& '6 0) 36 (;7 966WLHRII 36 6'$+287 6'$+ 6&/+6&( 5(6 9273352* '& '%6'2 '% '%6$ '%6$ '% '% 9''WLHRII (5' 5::5 '%6'$7$ '%6&/. 9'' 9'' 9'' 966 966 7 7 7 7 7 926 926 9/&'287 9/&'6(16( \ [ 5 5 & & 3&) Rev. 6 — 10 February 2015 All information provided in this document is subject to legal disclaimers. 9/&',1 6.1 Pinning 5 5 5 Product data sheet 6. Pinning information VSS(tie-off) and VDD(tie-off) are used for local tie-offs (see Section 6.2.1). Fig 2. Pin configuration for PCF8811 PCF8811 4 of 94 © NXP Semiconductors N.V. 2015. All rights reserved. Viewed from active side. Not drawn to scale. 80 x 128 pixels matrix LCD driver DDD PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 6.2 Pin description Table 2. Pin description Input or input/output pins must always be at a defined level (VSS or VDD) unless otherwise specified. PCF8811 Product data sheet Symbol Pin Description - 1 dummy_slanted - 2 alignment mark - 3 to 8 dummy MF2 to MF0 9 to 11 manufacturer device ID input DS0 12 device recognition input OSC 13 oscillator input EXT 14 extended command set input PS0 to PS2 15 to 17 parallel/serial/I2C-bus data selection input VSS(tie-off) 18 VSS tie-off SDAHOUT 19 I2C-bus data output SDAH 20, 21 I2C-bus data input SCLH/SCE 22, 23 I2C-bus clock input or chip enable, active LOW (6800 interface) VOTPPROG 24 to 26 supply voltage for OTP (can be combined with SCLH/SCE) RES 27 external reset input D/C 28 data or command, active LOW input R/W/WR 29 read or write, active LOW input (6800 interface) E/RD 30 clock enable or read, active LOW input (6800 interface) VDD(tie-off) 31 VDD tie-off DB0, DB1 32, 33 parallel data input/output DB2/SA0 34 parallel data input/output or I2C-bus slave address input DB3/SA1 35 DB4 36 parallel data input/output DB5/SDO 37 parallel data input/output or serial data output DB6/SCLK 38 parallel data input/output or serial clock input DB7/SDATA 39 parallel data input/output or serial data input VDD1 40 to 45 supply voltage (logic) VDD2 46 to 55 supply voltage for the internal voltage multiplier VDD3 56 to 60 supply voltage for the internal voltage multiplier VSS1 61 to 70 ground VSS2 71 to 80 ground for voltage multiplier T5 81 test pins T2 82 T1 83 T4 84 T3 85 All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 5 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 2. Pin description …continued Input or input/output pins must always be at a defined level (VSS or VDD) unless otherwise specified. Symbol Pin Description VOS4 86 VLCD offset input pins VOS3 87 VOS2 88 VOS1 89 VOS0 90 VLCDOUT 91 to 99 voltage multiplier output VLCDSENSE 100 voltage multiplier regulation input VLCDIN 101 to 107 LCD supply voltage - 108 - 109 to 114 dummy alignment mark R79 to R40 115 to 154 LCD row driver output R80[1] 155 C0 to C127 156 to 283 LCD column driver output R0 to R39 284 to 323 LCD row driver output - 324 to 333 dummy [1] Duplicate of R79. 6.2.1 Tie-off pins The PCF8811 has two tie-off pins: • VSS(tie-off), pin 18, at VSS potential • VDD(tie-off), pin 31, at VDD potential The tie-off pins have been implemented to allow a one layer layout of the application while offering the possibility to connect, for example, the pins MF0 to MF2 and VOS0 to VOS4 to any desired combination of LOW (VSS potential) and HIGH (VDD potential) levels. 6.2.2 Bare die information PP PP 3&) SLWFK \ [ DDJ Dimension including saw lane. Wafer thickness (excluding bumps): 380 (20) m. Fig 3. PCF8811 Product data sheet Chip dimensions All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 6 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 3. Bump and pad dimensions Pin Row/Column side (m) Interface side (m) Bump dimensions 29.9 98.5 (3) 32.2 93.5 (3) Pad dimension (aluminum) 42.84 105 50 100 Bump pitch 51.84 min 54.0 min Alignment marker position[1] Table 4. Pin X (m) Y (m) 2 5995 1017 108 5904 1017 [1] For the position of each pin, see Table 5. P \FHQWHU [FHQWHU PJZ Fig 4. Alignment markers Table 5. Bump locations All x/y coordinates represent the position of the center of each bump with respect to the center (x/y = 0) of the chip, see Figure 2. Input or input/output pins must always be at a defined level (VSS or VDD) unless otherwise specified. Symbol Bump Location Pitch X (m) Y (m) X (m) - 1 6092.00 1030.00 - dummy_slanted - 2 5995.00 1017.00 97 alignment mark - 3 5876.00 1030.00 119 dummy - 4 5822.00 1030.00 54 - 5 5768.00 1030.00 54 - 6 5714.00 1030.00 54 - 7 5660.00 1030.00 54 - 8 5390.00 1030.00 270 MF2 9 5012.00 1030.00 378 MF1 10 4850.00 1030.00 162 MF0 11 4688.00 1030.00 162 Description manufacturer device ID input DS0 12 4526.00 1030.00 162 device recognition input OSC 13 4364.00 1030.00 162 oscillator input EXT 14 4094.00 1030.00 270 extended command set input PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 7 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 5. Bump locations …continued All x/y coordinates represent the position of the center of each bump with respect to the center (x/y = 0) of the chip, see Figure 2. Input or input/output pins must always be at a defined level (VSS or VDD) unless otherwise specified. Symbol Bump Location Pitch X (m) Y (m) X (m) Description parallel/serial/I2C-bus data selection input PS0 15 3932.00 1030.00 162 PS1 16 3770.00 1030.00 162 PS2 17 3608.00 1030.00 162 VSS(tie-off) 18 3446.00 1030.00 162 for local tie-offs SDAHOUT 19 2960.00 1030.00 486 I2C-bus data output SDAH 20 2420.00 1030.00 540 I2C-bus data input SDAH 21 2366.00 1030.00 54 SCLH/SCE 22 1826.00 1030.00 540 SCLH/SCE 23 1772.00 1030.00 54 VOTPPROG 24 1664.00 1030.00 108 VOTPPROG 25 1610.00 1030.00 54 VOTPPROG 26 1556.00 1030.00 54 I2C-bus clock input or chip enable active LOW (6800 interface) supply voltage for OTP (can be combined with SCLH/SCE) RES 27 1448.00 1030.00 108 external reset input D/C 28 1232.00 1030.00 216 data or command active LOW input R/W/WR 29 962.00 1030.00 270 read or write active LOW input (6800 interface) E/RD 30 800.00 1030.00 162 clock enable or read active LOW input (6800 interface) VDD(tie-off) 31 638.00 1030.00 162 for local tie-offs DB0 32 476.00 1030.00 162 parallel data input/output DB1 33 314.00 1030.00 162 DB2/SA0 34 152.00 1030.00 162 DB3/SA1 35 10.00 1030.00 162 parallel data input/output or I2C-bus slave address input DB4 36 172.00 1030.00 162 parallel data input/output DB5/SDO 37 334.00 1030.00 162 parallel data input/output or serial data output DB6/SCLK 38 550.00 1030.00 216 parallel data input/output or serial clock input DB7/SDATA 39 712.00 1030.00 162 parallel data input/output or serial data input VDD1 40 874.00 1030.00 162 supply voltage (logic) VDD1 41 928.00 1030.00 54 VDD1 42 982.00 1030.00 54 VDD1 43 1036.00 1030.00 54 VDD1 44 1090.00 1030.00 54 VDD1 45 1144.00 1030.00 54 PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 8 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 5. Bump locations …continued All x/y coordinates represent the position of the center of each bump with respect to the center (x/y = 0) of the chip, see Figure 2. Input or input/output pins must always be at a defined level (VSS or VDD) unless otherwise specified. Symbol Bump Location X (m) Pitch Y (m) Description X (m) VDD2 46 1198.00 1030.00 54 VDD2 47 1252.00 1030.00 54 VDD2 48 1306.00 1030.00 54 VDD2 49 1360.00 1030.00 54 VDD2 50 1414.00 1030.00 54 VDD2 51 1468.00 1030.00 54 VDD2 52 1522.00 1030.00 54 VDD2 53 1576.00 1030.00 54 VDD2 54 1630.00 1030.00 54 VDD2 55 1684.00 1030.00 54 VDD3 56 1738.00 1030.00 54 VDD3 57 1792.00 1030.00 54 VDD3 58 1846.00 1030.00 54 VDD3 59 1900.00 1030.00 54 VDD3 60 1954.00 1030.00 54 VSS1 61 2062.00 1030.00 108 VSS1 62 2116.00 1030.00 54 VSS1 63 2170.00 1030.00 54 VSS1 64 2224.00 1030.00 54 VSS1 65 2278.00 1030.00 54 VSS1 66 2332.00 1030.00 54 VSS1 67 2386.00 1030.00 54 VSS1 68 2440.00 1030.00 54 VSS1 69 2494.00 1030.00 54 VSS1 70 2548.00 1030.00 54 VSS2 71 2602.00 1030.00 54 VSS2 72 2656.00 1030.00 54 VSS2 73 2710.00 1030.00 54 VSS2 74 2764.00 1030.00 54 VSS2 75 2818.00 1030.00 54 VSS2 76 2872.00 1030.00 54 VSS2 77 2926.00 1030.00 54 VSS2 78 2980.00 1030.00 54 VSS2 79 3034.00 1030.00 54 VSS2 80 3088.00 1030.00 54 T5 81 3250.00 1030.00 162 test input 5 T2 82 3304.00 1030.00 54 test input 2 T1 83 3466.00 1030.00 162 test input 1 PCF8811 Product data sheet supply voltage for the internal voltage multiplier supply voltage for the internal voltage multiplier ground ground for voltage multiplier All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 9 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 5. Bump locations …continued All x/y coordinates represent the position of the center of each bump with respect to the center (x/y = 0) of the chip, see Figure 2. Input or input/output pins must always be at a defined level (VSS or VDD) unless otherwise specified. Symbol Bump Location Pitch X (m) Y (m) X (m) Description T4 84 3628.00 1030.00 162 test input 4 T3 85 3790.00 1030.00 162 test input 3 VOS4 86 4060.00 1030.00 270 VLCD offset input pin 4 VOS3 87 4222.00 1030.00 162 VLCD offset input pin 3 VOS2 88 4384.00 1030.00 162 VLCD offset input pin 2 VOS1 89 4654.00 1030.00 270 VLCD offset input pin 1 VOS0 90 4816.00 1030.00 162 VLCD offset input pin 0 VLCDOUT 91 4924.00 1030.00 108 voltage multiplier output VLCDOUT 92 4978.00 1030.00 54 VLCDOUT 93 5032.00 1030.00 54 VLCDOUT 94 5086.00 1030.00 54 VLCDOUT 95 5140.00 1030.00 54 VLCDOUT 96 5194.00 1030.00 54 VLCDOUT 97 5248.00 1030.00 54 VLCDOUT 98 5302.00 1030.00 54 VLCDOUT 99 5356.00 1030.00 54 VLCDSENSE 100 5410.00 1030.00 54 voltage multiplier regulation input VLCDIN 101 5464.00 1030.00 54 LCD supply voltage VLCDIN 102 5518.00 1030.00 54 VLCDIN 103 5572.00 1030.00 54 VLCDIN 104 5626.00 1030.00 54 VLCDIN 105 5680.00 1030.00 54 VLCDIN 106 5734.00 1030.00 54 VLCDIN 107 5788.00 1030.00 54 - 108 5904.00 1017.00 116 alignment mark - 109 6004.00 1030.00 100 dummy - 110 6058.00 1030.00 54 - 111 6112.00 1030.00 54 - 112 6129.24 1032.50 - - 113 6077.40 1032.50 51.84 - 114 6025.56 1032.50 51.84 R79 115 5973.72 1032.50 51.84 PCF8811 Product data sheet LCD row driver output (R79 is the icon row when the icon row is enabled) All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 10 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 5. Bump locations …continued All x/y coordinates represent the position of the center of each bump with respect to the center (x/y = 0) of the chip, see Figure 2. Input or input/output pins must always be at a defined level (VSS or VDD) unless otherwise specified. Symbol Bump Location Pitch X (m) Y (m) X (m) R78 116 5921.88 1032.50 51.84 R77 117 5870.04 1032.50 51.84 R76 118 5818.20 1032.50 51.84 R75 119 5766.36 1032.50 51.84 R74 120 5714.52 1032.50 51.84 R73 121 5662.68 1032.50 51.84 R72 122 5610.84 1032.50 51.84 R71 123 5559.00 1032.50 51.84 R70 124 5507.16 1032.50 51.84 R69 125 5455.32 1032.50 51.84 R68 126 5403.48 1032.50 51.84 R67 127 5351.64 1032.50 51.84 R66 128 5299.80 1032.50 51.84 R65 129 5247.96 1032.50 51.84 R64 130 5196.12 1032.50 51.84 R63 131 5144.28 1032.50 51.84 R62 132 5092.44 1032.50 51.84 R61 133 5040.60 1032.50 51.84 R60 134 4988.76 1032.50 51.84 R59 135 4936.92 1032.50 51.84 R58 136 4885.08 1032.50 51.84 R57 137 4833.24 1032.50 51.84 R56 138 4781.40 1032.50 51.84 R55 139 4729.56 1032.50 51.84 R54 140 4677.72 1032.50 51.84 R53 141 4625.88 1032.50 51.84 R52 142 4574.04 1032.50 51.84 R51 143 4522.20 1032.50 51.84 R50 144 4470.36 1032.50 51.84 R49 145 4418.52 1032.50 51.84 R48 146 4366.68 1032.50 51.84 R47 147 4314.84 1032.50 51.84 R46 148 4263.00 1032.50 51.84 R45 149 4211.16 1032.50 51.84 PCF8811 Product data sheet Description LCD row driver output All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 11 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 5. Bump locations …continued All x/y coordinates represent the position of the center of each bump with respect to the center (x/y = 0) of the chip, see Figure 2. Input or input/output pins must always be at a defined level (VSS or VDD) unless otherwise specified. Symbol Bump Location Pitch X (m) Y (m) X (m) Description R44 150 4159.32 1032.50 51.84 R43 151 4107.48 1032.50 51.84 R42 152 4055.64 1032.50 51.84 R41 153 4003.80 1032.50 51.84 R40 154 3951.96 1032.50 51.84 R80 155 3900.12 1032.50 51.84 duplicate of R79 C0 156 3640.92 1032.50 259.2 LCD column driver output C1 157 3589.08 1032.50 51.84 C2 158 3537.24 1032.50 51.84 C3 159 3485.40 1032.50 51.84 C4 160 3433.56 1032.50 51.84 C5 161 3381.72 1032.50 51.84 C6 162 3329.88 1032.50 51.84 C7 163 3278.04 1032.50 51.84 C8 164 3226.20 1032.50 51.84 C9 165 3174.36 1032.50 51.84 C10 166 3122.52 1032.50 51.84 C11 167 3070.68 1032.50 51.84 C12 168 3018.84 1032.50 51.84 C13 169 2967.00 1032.50 51.84 C14 170 2915.16 1032.50 51.84 C15 171 2863.32 1032.50 51.84 C16 172 2811.48 1032.50 51.84 C17 173 2759.64 1032.50 51.84 C18 174 2707.80 1032.50 51.84 C19 175 2655.96 1032.50 51.84 C20 176 2604.12 1032.50 51.84 C21 177 2552.28 1032.50 51.84 C22 178 2500.44 1032.50 51.84 C23 179 2448.60 1032.50 51.84 C24 180 2396.76 1032.50 51.84 C25 181 2344.92 1032.50 51.84 C26 182 2293.08 1032.50 51.84 C27 183 2241.24 1032.50 51.84 C28 184 2189.40 1032.50 51.84 C29 185 2137.56 1032.50 51.84 C30 186 2085.72 1032.50 51.84 PCF8811 Product data sheet LCD row driver output All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 12 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 5. Bump locations …continued All x/y coordinates represent the position of the center of each bump with respect to the center (x/y = 0) of the chip, see Figure 2. Input or input/output pins must always be at a defined level (VSS or VDD) unless otherwise specified. Symbol Bump Location Pitch X (m) Y (m) X (m) C31 187 2033.88 1032.50 51.84 C32 188 1878.36 1032.50 155.52 C33 189 1826.52 1032.50 51.84 C34 190 1774.68 1032.50 51.84 C35 191 1722.84 1032.50 51.84 C36 192 1671.00 1032.50 51.84 C37 193 1619.16 1032.50 51.84 C38 194 1567.32 1032.50 51.84 C39 195 1515.48 1032.50 51.84 C40 196 1463.64 1032.50 51.84 C41 197 1411.80 1032.50 51.84 C42 198 1359.16 1032.50 52.64 C43 199 1308.12 1032.50 51.04 C44 200 1256.28 1032.50 51.84 C45 201 1204.44 1032.50 51.84 C46 202 1152.60 1032.50 51.84 C47 203 1100.76 1032.50 51.84 C48 204 1048.92 1032.50 51.84 C49 205 997.08 1032.50 51.84 C50 206 945.24 1032.50 51.84 C51 207 893.40 1032.50 51.84 C52 208 841.56 1032.50 51.84 C53 209 789.72 1032.50 51.84 C54 210 737.88 1032.50 51.84 C55 211 686.04 1032.50 51.84 C56 212 634.20 1032.50 51.84 C57 213 582.36 1032.50 51.84 C58 214 530.52 1032.50 51.84 C59 215 478.68 1032.50 51.84 C60 216 426.84 1032.50 51.84 C61 217 375.00 1032.50 51.84 C62 218 323.16 1032.50 51.84 C63 219 271.32 1032.50 51.84 C64 220 115.80 1032.50 155.52 C65 221 63.96 1032.50 51.84 C66 222 12.12 1032.50 51.84 C67 223 39.72 1032.50 51.84 C68 224 91.56 1032.50 51.84 C69 225 143.40 1032.50 51.84 PCF8811 Product data sheet Description LCD column driver output All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 13 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 5. Bump locations …continued All x/y coordinates represent the position of the center of each bump with respect to the center (x/y = 0) of the chip, see Figure 2. Input or input/output pins must always be at a defined level (VSS or VDD) unless otherwise specified. Symbol Bump Location X (m) Pitch Y (m) X (m) C70 226 195.24 1032.50 51.84 C71 227 247.08 1032.50 51.84 C72 228 298.92 1032.50 51.84 C73 229 350.76 1032.50 51.84 C74 230 402.60 1032.50 51.84 C75 231 454.44 1032.50 51.84 C76 232 506.28 1032.50 51.84 C77 233 558.12 1032.50 51.84 C78 234 609.96 1032.50 51.84 C79 235 661.80 1032.50 51.84 C80 236 713.64 1032.50 51.84 C81 237 765.48 1032.50 51.84 C82 238 817.32 1032.50 51.84 C83 239 869.16 1032.50 51.84 C84 240 921.00 1032.50 51.84 C85 241 972.84 1032.50 51.84 C86 242 1024.68 1032.50 51.84 C87 243 1076.52 1032.50 51.84 C88 244 1128.36 1032.50 51.84 C89 245 1180.20 1032.50 51.84 C90 246 1232.04 1032.50 51.84 C91 247 1283.88 1032.50 51.84 C92 248 1335.72 1032.50 51.84 C93 249 1387.56 1032.50 51.84 C94 250 1439.40 1032.50 51.84 C95 251 1491.24 1032.50 51.84 C96 252 1646.76 1032.50 155.52 C97 253 1698.60 1032.50 51.84 C98 254 1750.44 1032.50 51.84 C99 255 1802.28 1032.50 51.84 C100 256 1854.12 1032.50 51.84 C101 257 1905.96 1032.50 51.84 C102 258 1957.80 1032.50 51.84 C103 259 2009.64 1032.50 51.84 C104 260 2061.48 1032.50 51.84 C105 261 2113.32 1032.50 51.84 C106 262 2165.16 1032.50 51.84 C107 263 2217.00 1032.50 51.84 C108 264 2268.84 1032.50 51.84 PCF8811 Product data sheet Description LCD column driver output All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 14 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 5. Bump locations …continued All x/y coordinates represent the position of the center of each bump with respect to the center (x/y = 0) of the chip, see Figure 2. Input or input/output pins must always be at a defined level (VSS or VDD) unless otherwise specified. Symbol Bump Location X (m) Pitch Y (m) X (m) C109 265 2320.68 1032.50 51.84 C110 266 2372.52 1032.50 51.84 C111 267 2424.36 1032.50 51.84 C112 268 2476.20 1032.50 51.84 C113 269 2528.04 1032.50 51.84 C114 270 2579.88 1032.50 51.84 C115 271 2631.72 1032.50 51.84 C116 272 2683.56 1032.50 51.84 C117 273 2735.40 1032.50 51.84 C118 274 2787.24 1032.50 51.84 C119 275 2839.08 1032.50 51.84 C120 276 2890.92 1032.50 51.84 C121 277 2942.76 1032.50 51.84 C122 278 2994.60 1032.50 51.84 C123 279 3046.44 1032.50 51.84 C124 280 3098.28 1032.50 51.84 C125 281 3150.12 1032.50 51.84 C126 282 3201.96 1032.50 51.84 C127 283 3253.80 1032.50 51.84 R0 284 3461.16 1032.50 207.36 R1 285 3513.00 1032.50 51.84 R2 286 3564.84 1032.50 51.84 R3 287 3616.68 1032.50 51.84 R4 288 3668.52 1032.50 51.84 R5 289 3720.36 1032.50 51.84 R6 290 3772.20 1032.50 51.84 R7 291 3824.04 1032.50 51.84 R8 292 3875.88 1032.50 51.84 R9 293 3927.72 1032.50 51.84 R10 294 3979.56 1032.50 51.84 R11 295 4031.40 1032.50 51.84 R12 296 4083.24 1032.50 51.84 R13 297 4135.08 1032.50 51.84 R14 298 4186.92 1032.50 51.84 R15 299 4238.76 1032.50 51.84 R16 300 4290.60 1032.50 51.84 R17 301 4342.44 1032.50 51.84 PCF8811 Product data sheet Description LCD column driver output LCD row driver output All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 15 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 5. Bump locations …continued All x/y coordinates represent the position of the center of each bump with respect to the center (x/y = 0) of the chip, see Figure 2. Input or input/output pins must always be at a defined level (VSS or VDD) unless otherwise specified. Symbol Bump Location X (m) Pitch Y (m) X (m) R18 302 4394.28 1032.50 51.84 R19 303 4446.12 1032.50 51.84 R20 304 4497.96 1032.50 51.84 R21 305 4549.80 1032.50 51.84 R22 306 4601.64 1032.50 51.84 R23 307 4653.48 1032.50 51.84 R24 308 4705.32 1032.50 51.84 R25 309 4757.16 1032.50 51.84 R26 310 4809.00 1032.50 51.84 R27 311 4860.84 1032.50 51.84 R28 312 4912.68 1032.50 51.84 R29 313 4964.52 1032.50 51.84 R30 314 5016.36 1032.50 51.84 R31 315 5068.20 1032.50 51.84 R32 316 5120.04 1032.50 51.84 R33 317 5171.88 1032.50 51.84 R34 318 5223.72 1032.50 51.84 R35 319 5275.56 1032.50 51.84 R36 320 5327.40 1032.50 51.84 R37 321 5379.24 1032.50 51.84 R38 322 5431.08 1032.50 51.84 R39 323 5482.92 1032.50 51.84 - 324 5638.44 1032.50 155.52 - 325 5690.28 1032.50 51.84 - 326 5742.12 1032.50 51.84 - 327 5793.96 1032.50 51.84 - 328 5845.80 1032.50 51.84 - 329 5897.64 1032.50 51.84 - 330 5949.48 1032.50 51.84 - 331 6001.32 1032.50 51.84 - 332 6053.16 1032.50 51.84 - 333 6105.00 1032.50 51.84 PCF8811 Product data sheet Description LCD row driver output dummy All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 16 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 7. Functional description 7.1 Pin functions 7.1.1 R0 to R80: row driver outputs These pins output the display row signals. R79 is the icon row when the icon row is enabled. R80 is the duplicate of R79. 7.1.2 C0 to C127: column driver signals These pins output the display column signals. 7.1.3 VSS1 and VSS2: negative power supply rails VSS2 is for the voltage multiplier. These 2 supply rails must be connected together. 7.1.4 VDD1 to VDD3: positive power supply rails • VDD2 and VDD3 are the supply voltages for the internal voltage multiplier • VDD2 and VDD3 have the same voltage and may be connected together outside of the chip, see Section 18 • VDD1 is used as supply for the rest of the chip • VDD1 can be connected together with VDD2 and VDD3 • If the internal voltage multiplier is not used, then pins VDD2 and VDD3 must be connected to VDD1, see Section 18 • If VDD1, VDD2 and VDD3 are connected together, care must be taken with respect to the supply voltage range, see Section 15 7.1.5 VOTPPROG: OTP power supply Supply voltage for the OTP programming, see Section 19. In order to reduce the external connections, VOTPPROG can be combined with the SCLH/SCE pin. 7.1.6 VLCDOUT, VLCDIN, and VLCDSENSE: LCD power supply Positive power supply for the liquid crystal display. • If the internal VLCD multiplier is used, then all three inputs must be connected together • If VLCD multiplier is disabled and an external voltage is supplied to VLCDIN, then VLCDOUT must be left open-circuit and VLCDSENSE must be connected to VLCDIN • VDD2 and VDD3 should be applied according to the specified voltage range • If the PCF8811 is in power-save mode, the external LCD supply voltage can be switched off 7.1.7 T1 to T5: test pins T1, T2 and T5 must be connected to VSS. T3 and T4 must be left open-circuit. These test pins are not accessible to the user. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 17 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 7.1.8 MF2 to MF0 MF2 to MF0 are device manufacturer ID pins. These pins are meant to encode an IC supplier or a module maker. A module maker may want to be able to read which IC-supplier is on a module. Similarly they can be used if various suppliers for identical modules are used in order to identify the module supplier. By reading the values for MF2 to MF0, the manufacturer ID can be detected. Any possible combination can be used. 7.1.9 DS0 The device recognition pin, DS0, allows configuring the PCF8811 for 64 rows or 80 rows, see Table 6. Other configurations of raws can be done by command, see Table 12. The status of the DS0 pin can be read back by the status register, see Table 12. Table 6. Device recognition DS0 pin connected to Description VSS1 64-row driver VDD1 80-row driver 7.1.10 VOS4 to VOS0 These 5 input pins enable the calibration of the offset of the programmed VLCD, see Equation 4 and Equation 5. VOS4 to VOS0 must be connected to VDD1 or VSS1. 7.1.11 EXT: extended command set Input to select the basic command set or the extended command set. Must be connected on the module to have only one command set enabled, see Table 7. Table 7. Command set selection Pin Level Description EXT LOW (VSS1) basic command set HIGH (VDD1) extended command set Remark: NXP Semiconductors recommends that the extended command set is used. 7.1.12 PS0, PS1, and PS2 Parallel, serial or I2C-bus interface selection, see Table 8. Table 8. Interface selection PS[2:0] Interface 000 3-line SPI 001 4-line SPI 010 no operation 011 6800 parallel interface 100 or 110 I2C-bus interface 101 or 111 3-line serial interface 7.1.13 D/C Input to select either data or command input (see Table 9, Section 10.1.1 and Section 10.1.2). Not used for the 3-line serial interface, 3-line SPI and I2C-bus interface. When not used, it must be connected to VDD1 or VSS1. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 18 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 7.1.14 R/W/WR Input to select read or write mode when the 6800 parallel interface is selected. Not used in the serial and I2C-bus mode. When not used, it must be connected to VDD1 or VSS1. 7.1.15 E/RD E is the clock enable input for the 6800 parallel bus. Not used in the serial or I2C-bus interface. When not used, it must be connected to VDD1 or VSS1. 7.1.16 SCLH/SCE Input to select the chip and so allowing data or commands to be clocked in. Or input for the serial clock line when the I2C-bus interface is selected. 7.1.17 SDAH I2C-bus serial data input. When not used, it must be connected to VDD1 or VSS1. 7.1.18 SDAHOUT SDAHOUT is the serial data acknowledge output for the I2C-bus interface. • By connecting SDAHOUT to SDAH externally, the SDAH line becomes fully I2C-bus compatible • The acknowledge output is separated from the serial data line due to the following reasons: – In COG applications, the track resistance from the SDAHOUT pin to the system SDAH line can be significant. A potential divider is generated by the bus pull-up resistor and the ITO track resistance – It is possible that during the acknowledge cycle, the PCF8811 is not able to create a valid LOW level – By splitting the SDAH input from the SDAHOUT output, the device could be used in a mode that ignores the acknowledge bit – In COG applications, where the acknowledge cycle is required, it is necessary to minimize the track resistance from the SDAHOUT pin to the system SDAH line to guarantee a valid LOW level • When not used, it must be connected to VDD1 or VSS1 7.1.19 DB7 to DB0 These input/output lines are used by several interfaces as described below. When not used in the serial interface or the I2C-bus, they must be connected to VDD1 or VSS1. 7.1.19.1 DB7 to DB0 (parallel interface) 8-bit bidirectional bus. DB7 is the MSB. 7.1.19.2 DB7, DB6 and DB5 (serial interface) • DB7 is used for serial input data (SDATA) when the serial interface is selected • DB6 (SCLK) is used for the serial input clock when the serial interface is selected • DB5 is used as the serial output of the serial interface (SDO) PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 19 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 7.1.19.3 DB3 and DB2 (I2C-bus interface) DB3 and DB2 are respectively the SA1 and SA0 inputs when the I2C-bus is selected. DB3 and DB2 can be used so that up to four PCF8811s can be distinguished on one I2C-bus. 7.1.20 OSC: oscillator • When the on-chip oscillator is used, this input must be connected to VDD1 • If an external clock signal is used, it is connected to this input • If the oscillator and an external clock are both inhibited by connecting the OSC pin to VSS1, the display is not clocked and may be left in a Direct Current (DC) state. To avoid a DC on the display, the chip should always be put into power-down mode before stopping the clock 7.1.21 RES: reset This signal resets the device and must be applied to initialize the chip properly. The signal is active LOW. 7.2 Block diagram functions See Figure 1 for the block diagram layout. 7.2.1 Address counter The address counter assigns addresses to the display data RAM for writing. The X address X[6:0] and the Y address Y[3:0] are set separately. 7.2.2 Display data RAM The PCF8811 contains an 80 128-bit static RAM which stores the display data. • The RAM is divided into 10 banks of 128 bytes (10 8 128 bit) • The icon row (when enabled) is always row 79 and located in bank 9 • During RAM access, data is transferred to the RAM via the parallel interface, serial interface or I2C-bus interface • There is a direct correspondence between the X address and the column output number 7.2.3 Timing generator The timing generator produces the various signals required to drive the internal circuitry. Internal chip operation is not affected by operations on the data bus. 7.2.4 Display address counter The display content is generated by reading out the RAM content for 2, 4, or 8 rows simultaneously, depending on the selected display size. This content is processed with the corresponding set of 2, 4, or 8 orthogonal functions and so generates the signals for switching the pixels in the display on or off according to the RAM content. Bit MP (see Table 19) allows configuration of the p value. The p value defines the number of rows which are simultaneously selected, see Table 25. It is possible to set the p value for the display sizes 64 and 80 manually to p = 4. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 20 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 7.2.5 Display status The display status (display on/off, normal display/all dots on and normal/inverse video) is set by the bits DON, DAL and E in the command display control, see Table 13. 7.2.6 LCD row and column drivers The PCF8811 contains 80 row and 128 column drivers, which connect the appropriate LCD bias voltages in sequence to the display and in accordance with the data to be displayed. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 21 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 8. Addressing Data is written in bytes to the RAM matrix of the PCF8811 as shown in Figure 5. The display RAM has a matrix of 80 128 bits. The columns are addressed by the address pointer. The address ranges are: X = 0 to 127 (111 1111), Y = 0 to 9 (1001). The Y address represents the bank number. The effective X and Y addresses are programmed in such an order to use the PCF8811 with different display sizes without additional loading of the microprocessor. Addresses outside these ranges are not allowed. The icon row, when enabled, is always row 79 and therefore located in bank 9. '35$0 EDQN WRSRI/&' 5 EDQN 5 EDQN 5 /&' EDQN 5 EDQN 5 5 PJZ Fig 5. PCF8811 Product data sheet DDRAM to display mapping All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 22 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 8.1 Display data RAM structure The mode for storing data into the data RAM depends on the selected command set. 8.1.1 Basic command set After a write operation, the column address counter (X address) auto-increments by one, and wraps to zero after the last column is written. The number of columns (X address) after which the wrap-around must occur can be programmed. The Y address counter does not auto-increment in the basic command set. The counter stops when a complete bank has been written to. In this case, the Y address counter must be set; for Y address, see Table 12. To write the next bank, see Figure 6. When only a part of the RAM is used, both X (Xmax) and Y (Ymax) addresses can be set. The data order in the basic command set is as defined in Figure 6. /6% 06% /6% <PD[ 06% ;DGGUHVV ;PD[ <DGGUHVV PJZ Fig 6. Sequence of writing data bytes into the RAM (basic command set) 8.1.2 Extended command set 8.1.2.1 Horizontal/vertical addressing Two different address modes are possible with the extended command set: horizontal address mode and vertical address mode. In the horizontal address mode (V = 0) the X address increments after each byte. After the last X address, X wraps around to 0 and Y increments to address the next row, see Figure 7. The number of columns (last X address) after which the wrap-around must occur can be programmed, see Xmax and Ymax in Table 12 and Table 13. In Figure 7 it can be seen that the X address is programmed as 127, and the Y address is programmed as 9. With Xmax and Ymax, the X and Y addresses can be programmed while the whole RAM is not being used. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 23 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver In the vertical addressing mode (V = 1) the Y address increments after each byte. After the last Y address (Y = 9), Y wraps around to 0 and X increments to address the next column, see Figure 8. The last Y address, after which Y wraps to 0, can be programmed. In Figure 8 it can be seen that the X address is programmed as 127, and the Y address is programmed as 9. With Xmax and Ymax, the X and Y addresses can be programmed while the whole RAM is not being used. After the very last address, the address pointers wrap around to address X = 0 and Y = 0 in both horizontal and vertical addressing modes. <DGGUHVV Fig 7. ;DGGUHVV PJZ Sequence of writing data bytes into the RAM with horizontal addressing; V = 0 (extended command set) <DGGUHVV Fig 8. PCF8811 Product data sheet ;DGGUHVV PJZ Sequence of writing data bytes into the RAM with vertical addressing; V = 1 (extended command set) All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 24 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 8.1.2.2 Data order The data order bit (DOR, see Table 12 and Table 19) defines the bit order (LSB or MSB on top) for writing into the RAM, see Figure 9 and Figure 10. This feature is only available in the extended command set. /6% 06% /6% PJZ 06% Fig 9. RAM byte organization, if DOR = 0 (extended command set) 06% /6% 06% PJZ /6% Fig 10. RAM byte organization, if DOR = 1 (extended command set) PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 25 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 8.1.2.3 Features available in both command sets Mirror X (MX): The MX bit (see Table 12, Table 13 and Section 12.5.1) allows horizontal mirroring: when MX = 1, the X address space is mirrored; the address X = 0 is then located at the right side (Xmax) of the display, see Figure 11. When MX = 0, the mirroring is disabled and the address X = 0 is located at the left side (column 0) of the display, see Figure 12. <PD[ ;PD[ ;DGGUHVV <DGGUHVV PJZ Fig 11. RAM format addressing; MX = 1 (both command sets) <PD[ ;DGGUHVV ;PD[ <DGGUHVV PJZ Fig 12. RAM format addressing; MX = 0 (both command sets) Mirror Y (MY): The MY bit (see Table 12, Table 13 and Section 12.5.2) allows vertical mirroring: when MY = 1, the Y address space is mirrored; the address Y = 0 is then located at the bottom of the display, see Figure 13. When MY = 0, the mirroring is disabled and the address Y = 0 is located at top of the display, see Figure 14. The icon row, when enabled, is always located in bank 9 and row 79. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 26 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver <PD[ ;DGGUHVV ;PD[ <DGGUHVV PJZ Fig 13. RAM format addressing; MY = 1 (both command sets) <PD[ ;DGGUHVV ;PD[ <DGGUHVV PJZ Fig 14. RAM format addressing; MY = 0 (both command sets) PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 27 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 9. Parallel interface The parallel interface, which can be selected, is the 6800 series 8-bit bidirectional interface for communication between the microcontroller and the LCD driver chip. The selection of this interface is achieved with pins PS2 to PS0, see Section 7.1.12. 9.1 6800 series parallel interface The interface functions of the 6800 series parallel interface are given in Table 9. Table 9. 6800 series parallel interface functions D/C R/W/WR Operation 0 0 command data write 0 1 read status register 1 0 display data write 1 1 none The parallel interface timing diagram for the 6800 series is shown in Figure 41. 10. Serial interfacing (SPI and serial interface) Communication with the microcontroller can also occur via a clock-synchronized Serial Peripheral Interface (SPI). It is possible to select between either a 3-line (SPI or serial interface) or a 4-line serial peripheral interface. Selection is achieved via pins PS2 to PS0, see Section 7.1.12). 10.1 Serial peripheral interface lines The serial peripheral interface is a 3-line or 4-line interface for communication between the microcontroller and the LCD driver chip. The 3 lines are: • SCE (chip enable) • SCLK (serial clock) • SDATA (serial data) For the 4-line serial peripheral interface, a separate D/C line is added. The PCF8811 is connected to the serial data I/O (SDA) of the microcontroller by connecting the two pins SDATA (data input) and SDO (data output) together. 10.1.1 Write mode The display data/command indication may be controlled either via software or the D/C select pin. When the D/C pin is used, display data is transmitted when D/C is HIGH, and command data is transmitted when D/C is LOW, see Figure 15 and Figure 16. When pin D/C is not used, the display data length instruction is used to indicate that a specific number of display data bytes (1 to 255) is to be transmitted, see Figure 17. The next byte after the display data string is handled as an instruction command. When the 3-line SPI interface is used, the display data/command is controlled by software. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 28 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver If SCE is pulled HIGH during a serial display data stream, the interrupted byte is invalid data but all previously transmitted data is valid. The next byte received will be handled as an instruction command, see Figure 18. 6&( '& 6&/. 6'$7$ '% '% '% '% '% '% '% '% PJZ Fig 15. Serial bus protocol: transmission of 1 byte 6&( '& 6&/. 6'$7$ '% '% '% '% '% '% '% '% '% '% '% '% '% '% '% '% '% '% '% PJZ Fig 16. Serial bus protocol: transmission of several bytes 6&( 6&/. 6'$7$ '% '% '% GDWD GDWD '% '% '% '% GLVSOD\OHQJWKLQVWUXFWLRQ DQGOHQJWKGDWDWZRE\WHV ODVW '% '% '% '% '% '% '% '% GDWD GLVSOD\GDWDVWULQJ LQVWUXFWLRQ PJZ Fig 17. Transmission of several bytes PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 29 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 6&( 6&/. 6'$7$ GDWD GDWD GDWD GDWD GDWD GDWD '% '% '% '% '% '% '% '% '% '% '% '% PJZ GLVSOD\GDWDVWULQJ LQVWUXFWLRQ Fig 18. Transmission interrupted by SCE 10.1.2 Read mode (only extended command set) The read mode of the interface means that the microcontroller reads data from the PCF8811. The microcontroller first has to send a command (the read status command) and then the PCF8811 responds by transmitting data on the SDO line. After that, SCE is required to go HIGH, see Figure 19. The PCF8811 samples the SDATA data on rising SCLK edges, but shifts SDO data on falling SCLK edges. So, the microcontroller is supposed to read SDO data on rising SCLK edges. After the read status command has been sent, the SDATA line must be set to 3-state not later than the falling SCLK edge of the last bit, see Figure 19. Serial interface timing diagrams are shown in Section 17.2. 6&( 5(6 6&/. 6'$7$ '% '% '% '% '% '% '% '% 6'2 '% '% '% '% '% '% '% '% UHDGRXWGDWD LQVWUXFWLRQ PJZ Fig 19. Read mode SPI 3-line and 4-line 10.2 Serial interface (3-line) The serial interface is also a 3-line bidirectional interface for communication between the microcontroller and the LCD driver chip. The 3 lines are: • SCE (chip enable) • SCLK (serial clock) • SDATA (serial data) PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 30 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver The PCF8811 is connected to the SDA of the microcontroller by two lines: SDATA (data input) and SDO (data output) which are connected together. 10.2.1 Write mode The write mode of the interface means that the microcontroller writes commands and data to the PCF8811. Each data packet contains a control bit (D/C) and a transmission byte. If D/C is LOW, the following byte is interpreted as a command byte. The instruction set is shown in Table 12. If D/C is HIGH, the following byte is stored in the display data RAM. After every data byte, the address counter is incremented automatically. Figure 20 shows the general format of the write mode and the definition of the transmission byte. 7UDQVPLVVLRQ%\WH7%FRPPDQGE\WHRUGDWDE\WH '& '% '% '% '% '% '% '% '% 06% '& /6% 7% '& 7% '& 7% PJX Fig 20. Serial data stream; write mode Any instruction can be sent in any order to the PCF8811; the MSB is transmitted first. The serial interface is initialized when SCE is HIGH. In this state, SCLK clock pulses have no effect and no power is consumed by the serial interface. A falling edge on SCE enables the serial interface and indicates the start of data transmission. Figure 21, Figure 22, and Figure 23 show the protocol of the write mode: • when SCE is HIGH, SCLK clocks are ignored; during the HIGH time of SCE, the serial interface is initialized • SCLK must be LOW on the falling SCE edge, see Figure 42 • SDATA is sampled on the rising edge of SCLK • D/C indicates, whether the byte is a command (D/C = 0) or RAM data (D/C = 1). It is sampled on the first rising SCLK edge • If SCE stays LOW after the last bit of a data/command byte, the serial interface receives the D/C bit of the next byte on the next rising edge of SCLK, see Figure 22 • A reset pulse RES interrupts the transmission. The data being written into the RAM may be corrupted. The registers are cleared. If SCE is LOW after the rising edge of RES, the serial interface is ready to receive the D/C bit of a data/command byte, see Figure 23. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 31 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 6&( 6&/. 6'$7$ '& '% '% '% '% '% '% '% '% DDL Fig 21. Write mode: a control bit followed by a transmission byte 6&( 6&/. 6'$7$ '& '% '% '% '% '% '% '% '% '& '% '% '% '% '% '% '% '% '& DDL Fig 22. Write mode: transmission of several bytes 6&( 5(6 6&/. 6'$7$ '& '& '% '% '% '% '% '% '% '% '% '% '% '% '& '% '% DDL Fig 23. Write mode: interrupted by reset (RES) 10.2.2 Read mode (only extended command set) The read mode of the interface means that the microcontroller reads data from the PCF8811. To do so, the microcontroller first has to send a command (the read status command) and then the following byte is transmitted in the opposite direction using SDO, see Figure 24. After that, SCE is required to go HIGH before a new command is sent. The PCF8811 samples the SDATA data on the rising SCLK edges, but shifts SDO data on the falling SCLK edges. Thus the microcontroller is supposed to read SDO data on rising SCLK edges. After the read status command has been sent, the SDATA line must be set to 3-state not later than the falling SCLK edge of the last bit, see Figure 24. The 8th read bit is shorter than the others because it is terminated by the rising SCLK edge, see Figure 45. The last rising SCLK edge sets SDO to 3-state after the delay time t4. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 32 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 6&( 6&/. 6'$7$ '& '% '% '% '% '% '% '% '% 6'2 '& '% '% '% '% '% '% '% '% DDL Fig 24. Read mode: serial interface 3-line 11. I2C-bus interface 11.1 Characteristics of the I2C-bus The I2C-bus is for bidirectional, two-line communication between different ICs or modules. Four operating speed modes are available: • • • • Standard-mode (Sm), with a bit rate up to 100 kbit/s Fast-mode (Fm), with a bit rate up to 400 kbit/s Fast-mode Plus (Fm+), with a bit rate up to 1 Mbit/s High-speed mode (Hs-mode), with a bit rate up to 3.4 Mbit/s. Standard-mode, Fast-mode and Fast-mode Plus all use the same serial bus protocol and data format. Hs-mode devices are fully downwards compatible and can be connected to an F/S-mode I2C-bus system. As no master code is transmitted in such a configuration (see Section 11.3), all Hs-mode master devices stay in F/S-mode and communicate at F/S-mode speeds with their current-source disabled. The SDAH and SCLH pins are used to connect to the F/S-mode bus system. The PCF8811 is able to work in all speed modes including HS-mode. For using the HS-mode, all components - including the master (see Section 11.1.1) - have to be able to run this mode. For more information, see Ref. 11 “UM10204”. 11.1.1 System configuration The system configuration is shown in Figure 25. Definitions of the I2C-bus terminology: • transmitter: the device which sends the data to the bus • receiver: the device which receives the data from the bus • master: the device which initiates a transfer, generates clock signals and terminates a transfer • slave: the device addressed by a master PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 33 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver • multi-master: more than one master can attempt to control the bus at the same time without corrupting the message • arbitration: procedure to ensure that only one master controls the bus, if more than one master simultaneously tries to control the bus. Therefore the message is not corrupted. • synchronization: procedure to synchronize the clock signals of two or more devices 0$67(5 75$160,77(5 5(&(,9(5 6/$9( 5(&(,9(5 6/$9( 75$160,77(5 5(&(,9(5 0$67(5 75$160,77(5 5(&(,9(5 0$67(5 75$160,77(5 6'$ 6&/ PJD Fig 25. System configuration 11.1.2 Bit transfer One data bit is transferred during each clock pulse, see Figure 26. The data on the SDA line must remain stable during the HIGH period of the clock pulse as changes in the data line at this time is interpreted as a control signal. 6'$ 6&/ GDWDOLQH VWDEOH GDWDYDOLG FKDQJH RIGDWD DOORZHG PEF Fig 26. Bit transfer 11.1.3 START and STOP conditions Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW change of the data line, while the clock is HIGH, is defined as the START condition (S). A LOW-to-HIGH change of the data line, while the clock is HIGH is defined as the STOP condition (P). The START and STOP conditions are shown in Figure 27. 6'$ 6'$ 6&/ 6&/ 6 3 67$57FRQGLWLRQ 6723FRQGLWLRQ PEF Fig 27. Definition of START and STOP conditions PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 34 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 11.1.4 Acknowledge The number of data bytes transferred between the START and STOP conditions from transmitter to receiver is unlimited. Each byte of 8 bits is followed by an acknowledge cycle. • A slave receiver which is addressed must generate an acknowledge after the reception of each byte • Also a master receiver must generate an acknowledge after the reception of each byte that has been clocked out of the slave transmitter • The device that acknowledges must pull-down the SDA line during the acknowledge clock pulse, so that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse (set-up and hold times must be considered) • A master receiver must signal an end of data to the transmitter by not generating an acknowledge on the last byte that has been clocked out of the slave. In this event, the transmitter must leave the data line HIGH to enable the master to generate a STOP condition Acknowledgement on the I2C-bus is shown in Figure 28. GDWDRXWSXW E\WUDQVPLWWHU QRWDFNQRZOHGJH GDWDRXWSXW E\UHFHLYHU DFNQRZOHGJH 6&/IURP PDVWHU 6 FORFNSXOVHIRU DFNQRZOHGJHPHQW 67$57 FRQGLWLRQ PEF Fig 28. Acknowledge on the I2C-bus 11.2 I2C-bus protocol Four I2C-bus slave addresses (0111 100, 0111 101, 0111 110 and 0111 111) are reserved for the PCF8811.The entire I2C-bus slave address byte is shown in Table 10. Table 10. I2C slave address byte Slave address Bit 7 6 5 4 3 2 1 MSB 0 0 LSB 1 1 1 1 SA1 SA0 R/W Bit 1 and bit 2 of the slave address byte, that a PCF8811 responds to, are defined by the level tied to SA0 and SA1 (VSS for logic 0 and VDD for logic 1). PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 35 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver The I2C-bus protocol is shown in Figure 29. The sequence is initiated with a START condition (S) from the I2C-bus master which is followed by one of four possible PCF8811 slave addresses available. All slaves with the corresponding slave address acknowledge in parallel, all others ignore the I2C-bus transfer. VODYHDGGUHVV FRQWUROE\WH 6 65 ' & 6 $ $ $ 2 & : 5$0FRPPDQGE\WH 0 / $ 6 6 3 % % (;$03/(6 DWUDQVPLWWZRE\WHVRI5$0GDWD 6 6 6 $ $ $ $ 5$0'$7$ $ $ &200$1' $ $ &200$1' $ 3 $ $ 5$0'$7$ $ 5$0'$7$ $ 3 EWUDQVPLWWZRFRPPDQGE\WHV 6 6 6 $ $ $ FWUDQVPLWRQHFRPPDQGE\WHDQGWZR5$0GDWHE\WHV 6 6 6 $ $ $ &200$1' $ 5$0'$7$ $ 3 DDD Fig 29. I2C-bus protocol After acknowledgement, one or more command words follow which define the status of the addressed slaves. A command word consists of a control byte, which defines bit Co and D/C, plus a data byte (see Figure 29, Table 11 and Figure 30). Table 11. Co and D/C definitions Bit Logic state R/W Action Co 0 0 last control byte to be sent; only a stream of data bytes is allowed to follow; this stream may only be terminated by a STOP or RESTART condition 1 0 another control byte follows the data byte unless a STOP or RESTART condition is received 0 0 data byte is decoded and used to set up the device 1 data byte returns the status byte 0 data byte is stored in the display RAM 1 RAM read back is not supported D/C 1 06% &R '& /6% QRWUHOHYDQW DDD Fig 30. Control byte format PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 36 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Within the last control byte, the Co bit is set logic 0. The command bytes and control bytes are also acknowledged by all addressed slaves connected to the bus. After the last control byte and depending on the D/C bit setting, either a series of display data bytes or command data bytes may follow. If the D/C bit was set to logic 1, these display bytes are stored in the display RAM at the address specified by the data pointer. The data pointer is automatically updated and the data is directed to the intended PCF8811 device. If the DC bit of the last control byte was set to logic 0, these command bytes are decoded and the setting of the device is changed according to the received commands. The acknowledgement after each byte is made only by the addressed PCF8811. At the end of the transmission, the I2C-bus master issues a STOP condition (P). 11.3 I2C-bus Hs-mode protocol The PCF8811 is a slave receiver/transmitter. The SDAHOUT pin must be connected if data is to be read from the device or a write-only configuration with acknowledge is desired. Hs-mode can only commence after the following conditions: • START condition (S) • 8-bit master code (0000 1xxx) • Not-acknowledge bit (A) The master code has two functions: it allows arbitration and synchronization between competing masters at F/S-mode speeds, resulting in one winner. The master code also indicates the beginning of a Hs-mode transfer. These conditions are shown in Figure 31 and Figure 32. +VPRGHFXUUHQWVRXUFHIRU6&/+HQDEOHG )6PRGH 6 0$67(5&2'( $ 6U 6/$9($'' 5: $ '$7$ )6PRGH $$ 3 QE\WHVDFN +VPRGHFRQWLQXHV 6U 6/$9($'' PVF Fig 31. Data transfer format in Hs-mode Hs-mode master codes are reserved 8-bit codes, which are not used for slave addressing or other purposes. Furthermore, as each master has its own unique master code, up to eight Hs-mode masters can be present on one I2C-bus system (although master code 00001000 should be reserved for test and diagnostic purposes). The master code for a Hs-mode master device is software programmable and is chosen by the system designer. Arbitration and clock synchronization only take place during the transmission of the master code and not-acknowledge bit (A), after which one winning master remains active. The master code indicates to other devices that a Hs-mode transfer is to begin and the connected devices must meet the Hs-mode specification. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 37 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver $ ELWPDVWHUFRGH[[[ 6 W W+ 6'$KLJK 6&/KLJK WR )6PRGH 5: ELW6/$ 6U QELWGDWD$$ $ 6U 3 6'$KLJK 6&/KLJK WR WR ,I3WKHQ )6PRGH +6PRGH ,I6UGRWWHGOLQHV WKHQ+6PRGH W+ W)6 0DVWHUFXUUHQWVRXUFHSXOOXS PVF 5HVLVWRUSXOOXS Fig 32. Data transfer timing format in F/S-mode and Hs-mode As no device is allowed to acknowledge the master code, the master code is followed by a not-acknowledge (A). After this A and the SCLH line pulled up to a HIGH level, the active master switches to Hs-mode and enables at tH the current-source pull-up circuit for the SCLH signal, see Figure 32. The active master then sends a repeated START condition (Sr) followed by a 7-bit slave address with a R/W bit, and receives an acknowledge bit (A) from the selected slave. After each acknowledge bit (A) or not-acknowledge bit (A), the active master disables its current source pull-up circuit. The active master re-enables its current source again when all devices have been released and the SCLH signal reaches a HIGH level. The rising of the SCLH signal is made by a pull-up resistor and therefore is slower, the last part of the SCLH rise time is speeded up because the current source is enabled. Data transfer only switches back to F/S-mode after a STOP condition (P). A write sequence, after the Hs-mode is selected, is shown in Figure 33. The sequence is initiated with a START condition (S) from the I2C-bus master which is followed by the slave address. All slaves with the corresponding address acknowledge in parallel, the remainder ignores the I2C-bus transfer. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 38 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver DFNQRZOHGJH IURP3&) 6 6 6U $ $ $ '& VODYHDGGUHVV 5: &R DFNQRZOHGJH IURP3&) FRQWUROE\WH $ DFNQRZOHGJH IURP3&) GDWDE\WH $ '& QE\WHV DFNQRZOHGJH IURP3&) FRQWUROE\WH $ E\WH &R DFNQRZOHGJH IURP3&) $ 3 GDWDE\WH QE\WHV 06%/6% PJZ Fig 33. Master transmits in Hs-mode to slave receiver; write mode After the acknowledgement cycle of a write (W), one or more command words will follow which define the status of the addressed slaves. A command word consists of a control byte, which defines continuation bit Co and D/C, plus a data byte, see Figure 33 and Table 11. The last control byte is initiated by bit Co (a cleared MSB). The control and data bytes are also acknowledged by all addressed slaves on the bus. A read sequence is shown in Figure 34 and again this sequence follows after the Hs-mode is selected. The PCF8811 immediately starts to output the requested data until a not-acknowledge is transmitted by the master. Before the read access, the user has to set the D/C bit to the appropriate value by a preceding write access. The write access must be terminated by a RESTART condition so that the Hs-mode is not disabled. DFNQRZOHGJH IURP3&) 6 6 6U $ $ $ QRWDFNQRZOHGJH IURPPDVWHU VWDWXVLQIRUPDWLRQ $ 3 VODYHDGGUHVV 5: 6723FRQGLWLRQ PJZ Fig 34. Master receives from slave transmitter (status register is read); read mode After the last control byte, depending on the D/C bit setting, either a series of display data bytes or command data bytes may follow. If the D/C bit was set to logic 1, these display bytes are stored in the display RAM at the address specified by the data pointer. The data pointer is automatically updated and the data is directed to the intended PCF8811 device. If the D/C bit of the last control byte was set to logic 0, these command bytes are decoded and the setting of the device is changed according to the received commands. The acknowledgement after each byte is made only by the addressed PCF8811. At the end of the transmission, the I2C-bus master issues a STOP condition (P) and switches back to the F/S-mode. However, to reduce the overhead of the master code, it is possible that a master can link a number of Hs-mode transfers, separated by repeated START conditions (Sr). PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 39 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 11.4 Command decoder The command decoder identifies command words that are received on the I2C-bus: • pairs of bytes: information in second byte, first byte determines whether information is display or instruction data • Stream of information bytes after Co = 0: display or instruction data depending on last D/C The most significant bit of a control byte is the continuation bit Co. If this bit is at logic 1, it indicates that only one data byte, either command or RAM data, follows. If this bit is at logic 0, it indicates that a series of data bytes, either command or RAM data, may follow. The DB6 bit of a control byte is the RAM data/command bit D/C. When this bit is at logic 1, it indicates that a RAM data byte is transferred next. If the bit is at logic 0, it indicates that a command byte is transferred next. 12. Instructions The PCF8811 interfaces via an 8-bit parallel interface, two different 3-line serial interfaces, a 4-wire serial interface or an I2C-bus interface. Processing of the instructions does not require the display clock. Data accesses to the PCF8811 can be broken down into two areas: one that defines the operating mode of the device, and one that fills the display RAM. In use of the parallel and 4-wire SPI interfaces, the distinction is the D/C pin. When the D/C pin is at logic 0, the chip responds to instructions as defined in Table 12. When the D/C bit is at logic 1, the chip sends data to the RAM. In use of the 3-wire SPI, the 3-wire serial interface or the I2C-bus interface, the distinction between instructions defining the operating mode of the device and instructions that fill the display RAM, is made respectively: • by the display data length instruction (3-line SPI) or • by the D/C bit in the data stream (3-line serial interface and I2C-bus interface). There are 4 types of instructions which: 1. Define the PCF8811 functions, such as display configuration 2. Set internal RAM addresses 3. Perform data transfer with internal RAM 4. Others. In normal use, category 3 instructions are used most frequently. A basic and an extended instruction set is available. If the EXT pin is set LOW, the basic command set is used. If the EXT pin is set HIGH, the extended command set is used. Both command sets are detailed in Table 12. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 40 of 94 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors PCF8811 Product data sheet Table 12. Instruction set[1] Instruction NOP Reset Pin Command byte EXT[2] D/C R/W/WR DB7[3] Description DB6 DB5 DB4 DB3 DB2 DB1 DB0 X 0 0 0 1 0 0 1 1 X X X 0 0 1 1 1 0 0 1 0 0 both perform no operation and either one can be used X 0 0 1 1 1 0 0 0 1 0 soft reset Rev. 6 — 10 February 2015 All information provided in this document is subject to legal disclaimers. Write data X 1 0 D7 D6 D5 D4 D3 D2 D1 D0 Display data length X 0 0 1 1 1 0 1 0 0 0 X 0 0 D7 D6 D5 D4 D3 D2 D1 D0 Status read X 0 1 BUSY DON RES MF2 MF1 MF0 X DS0 read status byte X 0 X 1 1 0 1 1 0 1 X read status byte Display control X 0 0 1 0 1 0 1 1 1 X 0 0 1 0 1 0 0 1 1 E X 0 0 1 0 1 0 0 1 0 DAL X 0 0 1 0 1 0 0 0 0 MX mirror X X 0 0 1 1 0 0 MY X X X mirror Y 1 0 0 1 1 1 0 1 1 1 IC icon enable or disable[4] 1 0 0 1 0 1 0 0 0 1 V vertical or horizontal addressing[4] 1 0 0 1 1 1 0 1 0 1 DOR data order[4] 1 0 0 1 1 1 0 1 1 0 BRS X 0 0 1 0 1 1 Y3 Y2 Y1 Y0 set Y address; 0 Y 9 X 0 0 0 0 0 1 0 X6 X5 X4 set X address; 0 X 127 Address commands 0 0 0 0 0 0 X3 X2 X1 X0 0 0 0 0 0 1 1 0 0 1 0 0 X X X X X 0 0 0 0 0 1 X 0 0 0 1 0 0 0 0 X X X 0 0 X L6 L5 L4 L3 L2 L1 L0 X 0 0 0 1 0 0 0 1 X X X 0 0 X C6 C5 C4 C3 C2 C1 C0 all pixels on or off bottom row swap[4] set Ymax; 0 Y 9 Ymax3 Ymax2 Ymax1 Ymax0 1 0 0 0 set Xmax; 0 X 127 Xmax6 Xmax5 Xmax4 Xmax3 Xmax2 Xmax1 Xmax0 set initial display line; 0 L 79[5] set start row; 0 C 79[6] PCF8811 X normal or reverse mode 80 x 128 pixels matrix LCD driver 41 of 94 © NXP Semiconductors N.V. 2015. All rights reserved. Set initial row DON display on or off X X Set initial display line write data to display RAM only used in 3-line SPI xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx Instruction set[1] …continued Instruction Set-partial-display Pin Command byte EXT[2] D/C R/W/WR DB7[3] DB6 DB5 DB4 DB3 DB2 DB1 DB0 X 0 0 0 1 0 0 1 0 X X Description set partial display 1:16 to 1:80 X 0 0 X P6 P5 P4 P3 P2 P1 P0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 X X VPR5 VPR4 VPR3 VPR2 VPR1 VPR0 0 0 0 0 0 1 0 0 1 0 0 1 0 0 0 0 0 0 1 1 0 0 VPR7 VPR6 VPR5 VPR4 VPR3 VPR2 VPR1 VPR0 Power control X 0 0 0 0 1 0 1 PC1 PC0 1 switch HVgen on/off HVgen stages 0 0 0 0 1 1 0 0 1 S1 S0 set multiplication factor 1 0 0 0 1 1 0 0 S2 S1 S0 set multiplication factor[4] FR 1 0 0 0 0 0 1 1 1 FR1 FR0 set frame rate frequency[4] TC[9] 1 0 0 0 0 1 1 1 TC2 TC1 TC0 set temperature coefficient[4] Bias system 0 0 0 0 1 0 1 0 BS2 BS1 BS0 set bias system[10] Manual p value (p = 4) 1 0 0 0 0 0 1 1 0 1 MP set manual p value[4][11] Power-save on X 0 0 1 0 1 0 1 0 0 1 power-save mode Power-save off X 0 0 1 1 1 0 0 0 0 1 exit power-save mode Internal oscillator X 0 0 1 0 1 0 1 0 1 OS switch internal oscillator on/off Internal oscillator 1 0 0 1 1 1 0 0 1 1 EC enable or disable the internal or external oscillator[4] Enter CALMM mode X 0 0 1 0 0 0 0 0 1 0 enter CALMM mode Reserved X 0 0 0 0 1 0 1 X X 0 reserved Reserved X 0 0 0 1 1 1 X X X X reserved Test X 0 0 1 1 1 1 X X X X do not use; reserved for testing VOP setting NXP Semiconductors PCF8811 Product data sheet Table 12. Rev. 6 — 10 February 2015 All information provided in this document is subject to legal disclaimers. [2] NXP Semiconductors recommends that the extended command set is used. [3] D7 = MSB. [4] Commands only available with the extended command set, EXT = 1. If EXT = 0 these commands have no effect. [5] When the icon mode is enabled the set initial display line 0 L 78. set VOP[4] [6] When the icon mode is enabled the set initial row line 0 C 78. [7] Commands only used for the basic command set EXT = 0. If EXT = 1 these commands have no effect. It must be checked, when setting VOP in the basic command set that it is followed by another command. PCF8811 X = value without meaning. VOFF2 VOFF1 VOFF0 offset for VOP[7][8] 80 x 128 pixels matrix LCD driver 42 of 94 © NXP Semiconductors N.V. 2015. All rights reserved. [1] set VOP[7][8] xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx The programming of VOP in the basic command set must be done in the following order: NXP Semiconductors PCF8811 Product data sheet [8] a) VPR[5:0] b) VOFF[2:0] c) must be followed by another command. [9] One fixed TC is set automatically if the basic command set is used. [10] Without function; implemented for compatibility with the Alt-Pleshko driver instruction set. [11] Only for multiplex rates 1:64 and 1:80. The number of simultaneous rows can be set manually to p = 4, see Table 19. Rev. 6 — 10 February 2015 All information provided in this document is subject to legal disclaimers. PCF8811 80 x 128 pixels matrix LCD driver 43 of 94 © NXP Semiconductors N.V. 2015. All rights reserved. PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 12.1 Instruction set commands 12.1.1 Common instructions of the basic and extended command set Table 13. Bit Logic 0 Logic 1 Reset state DON display off display on 0 E normal display inverse video mode 0 DAL normal display all pixels on 0 MX no X mirroring X mirroring 0 MY no Y mirroring Y mirroring 0 OC stop frame frequency calibration start frame frequency calibration 0 OS internal oscillator off start internal oscillator 0 X[6:0] set X address (column) for writing in the RAM 000 0000 Y[3:0] set Y address (bank) for writing in the RAM 0000 Xmax[6:0] set wrap around X address (column) 111 1111 Ymax[3:0] set wrap around Y address (bank) 1001 L[6:0] sets line address of the display; this command cannot access the icon driver row, row 79, if the icon row is enabled 000 0000 C[6:0] sets the initial row 0 of the display; this command cannot access the icon driver row, row 79, if the icon row is enabled 000 0000 P[6:0] partial display mode 1:16 to 1:80 PC[1:0] switch HV multiplier on/off 00 S[1:0] charge pump multiplication factor 00 [1] 101 0000 (1:80)/100 0000 (1:64) Power control register[1] PC[1:0] Description 00 HVgen off X1 HVgen on 1X HVgen on [1] Product data sheet [1] Partial displays can be selected in steps of 8, when the icon mode is not selected. When the icon mode is selected, partial displays can be selected in steps of 16. For example, without icons the available partial display sizes are 8, 16, 24, 32, 40, 48, 56, 64 or 72 lines. With icons, there are 16, 32, 48 or 64 lines possible. Table 14. PCF8811 Common commands X = value without meaning. All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 44 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Power-save mode (PSM), OS, DON, DAL and E combinations[1] Table 15. PSM OS DON DAL E Description Off 0 X X X oscillator off; HVgen disabled Off 1 X 0 X oscillator on; HVgen disabled Off 1 0 1 X display off; pins Rn/Cn at VSS; oscillator off; HVgen disabled[2] Off 1 1 0 0 normal display mode Off 1 1 0 1 inverse display mode Off 1 1 1 X all pixels on[3] On X X X X power-save mode: display off; pins Rn/Cn at VSS; oscillator off; HVgen disabled [1] X = value without meaning. [2] Bit DON can only be addressed after bit DAL is activated. [3] Bit DAL has priority over bit E. Table 16. Read status byte Bit Description BUSY if BUSY = 0 the chip is able to accept new commands DON same bit as in Table 15 RES if RES = 1 a reset is in progress MF[2:0] device manufacturer ID DS0 device recognition, see Table 6 Table 17. Multiplication settings S[1:0] Description 00 4 voltage multiplier 01 5 voltage multiplier 10 6 voltage multiplier 11 7 voltage multiplier 12.1.2 Specific commands of the basic command set Table 18. Specific basic commands Bit Description Reset state VPR[5:0] programming value of VLCD 00 0000 VOFF[2:0] offset for the programming value of VLCD 000 12.1.3 Specific commands of the extended command set Table 19. PCF8811 Product data sheet Specific extended commands Bit Logic 0 Logic 1 Reset state VPR[7:6] + VPR[5:0] programming value of VLCD 0000 0000 FR[1:0] frame rate frequency 11 TC[2:0] temperature coefficient 010 S[2:0] charge pump multiplication factor 100 All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 45 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 19. Bit Logic 0 Logic 1 Reset state V horizontal addressing vertical addressing 0 DOR LSB at top MSB at top 0 IC no icon row (multiplex rate 1:16 to 1:80) icon row (multiplex rate 0 1:16 to 1:80) BRS bottom rows are not mirrored bottom rows are mirrored MP[1] multiplex rate driven p value (automatic) p = 4 selected for 0 multiplex rate 1:64 and 1:80 EC use internal oscillator use external oscillator [1] 0 Frame rate frequency FR[1:0] Frame rate frequency 00 30 Hz 01 40 Hz 10 50 Hz 11 60 Hz Table 21. Temperature coefficient[1] TC[2:0] Temperature coefficient 000 0 001 1 010 2 011 3 100 4 101 5 110 6 111 7 [1] For further information about temperature coefficient, see Table 31. Table 22. Product data sheet 0 The default value for MP (Manual P) equals 0 and it is recommended to use that value as a starting point. However, depending on the liquid crystal properties, p = 4 may be a better choice and it is recommended to compare optical results for the automatically chosen value for p and for p=4 and use the one that gives best results. Table 20. PCF8811 Specific extended commands …continued Multiplication settings S[2:0] Description 000 2 voltage multiplier 001 3 voltage multiplier 010 4 voltage multiplier 011 5 voltage multiplier 100 4 voltage multiplier All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 46 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 22. Multiplication settings …continued S[2:0] Description 101 5 voltage multiplier 110 6 voltage multiplier 111 7 voltage multiplier 12.2 Initialization Reset is accomplished by applying an external reset pulse (active LOW) at pin RES. When reset occurs within the specified time, all internal registers are reset, however the RAM is still undefined. The state after reset is described in Section 12.3. Pin RES must be 0.3 VDD1 when VDD1 reaches VDD(min) (or higher) within a maximum time tVHRL after VDD1 goes HIGH, see Figure 48. A reset can also be achieved by sending a reset command. This command can be used during normal operation but not to initialize the chip after power-on. 12.3 Reset function 12.3.1 Basic command set After reset, the LCD driver has the following state: • • • • • • • Display setting E = 0 and DAL = 0 • • • • • • • • All LCD outputs at VSS (display off) Address commands X[6:0] = 0 and Y[3:0] = 0 VLCD is equal to 0, the HV multiplier is switched off (PC[1:0] = 00) No offset of the programming range (VOFF[2:0] = 0) HV multiplier programming (VPR[5:0] = 0) 4 voltage multiplier (S[1:0] = 00) After power-on, RAM data is undefined, the reset signal does not change the content of the RAM Initial display line set to line 0 (L[6:0] = 0) Initial row set to row 0 (C[6:0] = 0) Full display selected (P[6:0] = multiplex rate 1:80 or 1:64) Display is not mirrored (MX = 0; MY = 0) Internal oscillator is off Power-save mode is on No frame calibration is running 12.3.2 Extended command set After reset, the LCD driver has the following state: • Display settings E = 0 and DAL = 0 • Icons disabled (IC = 0) • Address counter X[6:0] = 0 and Y[3:0] = 0 PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 47 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver • • • • • • Temperature control mode TC2 (TC[2:0] = 010) • • • • • • • • • • • • All LCD outputs at VSS (display off) VLCD is equal to 0 V; the HV multiplier is switched off (PC[1:0] = 0) HV multiplier programming (VPR[7:0] = 0) 4 voltage multiplier (S[2:0] = 100) Frame-rate frequency (FR[1:0] = 11) After power-on, RAM data is undefined, the reset signal does not change the content of the RAM Full display selected (P[6:0] = multiplex rate 1:80 or 1:64) Initial display line set to line 0 (L[6:0] = 0) Initial row set to row 0 (C[6:0] = 0) Display is not mirrored (MX = 0; MY = 0) Internal oscillator is off Power-save mode is on Horizontal addressing enabled (V = 0) No data order swap (DOR = 0) No bottom row swap (BRS = 0) Internal oscillator enabled (EC = 0) No frame calibration running (OC = 0) 12.4 Power-save mode In the power-save mode the LCD driver has the following state: • • • • • All LCD outputs at VSS (display off) Bias generator and VLCD generator switched off; external VLCD can be disconnected Oscillator off (external clock possible) RAM contents not cleared; RAM data can be written VLCD discharged to VSS in power-down mode There are two ways to put the chip into power-save mode: • The display must be off (DON = 0) and all the pixels on (DAL = 1) • The power-save mode command is activated 12.5 Display control The bits DON, E and DAL select the display mode, see Table 15. 12.5.1 Bit MX When MX = 0: the display RAM is written from left to right (X = 0 is on the left side and X = Xmax is on the right side of the display). When MX = 1: the display RAM is written from right to left (X = 0 is on the right side and X = Xmax is on the left side of the display). PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 48 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver The MX bit has an impact on the way the RAM is written to. So if a horizontal mirroring of the display is desired, the RAM must first be rewritten, after changing the MX bit. 12.5.2 Bit MY When MY = 1, the display is mirrored vertically. A change to this bit has an immediate effect on the display. 12.6 Set Y address of RAM Y[3:0] defines the Y address of the display RAM. When the icon row (row 79) is enabled, it is always in bank 9 independent of the multiplex rate which is programmed Table 23. RAM X/Y address range Y3 Y2 Y1 Y0 Content Allowed X range 0 0 0 0 bank 0 (display RAM) 0 to 127 0 0 0 1 bank 1 (display RAM) 0 to 127 0 0 1 0 bank 2 (display RAM) 0 to 127 0 0 1 1 bank 3 (display RAM) 0 to 127 0 1 0 0 bank 4 (display RAM) 0 to 127 0 1 0 1 bank 5 (display RAM) 0 to 127 0 1 1 0 bank 6 (display RAM) 0 to 127 0 1 1 1 bank 7 (display RAM) 0 to 127 1 0 0 0 bank 8 (display RAM) 0 to 127 1 0 0 1 bank 9 (display RAM) 0 to 127 12.7 Set X address of RAM The X address points to the columns. The range of X is 0 to 127 (7Fh). 12.8 Set display start line L[6:0] (see Table 13) is used to select the display line address of the display RAM to be displayed on the initial row, row 0. The selection of L[6:0] is limited to steps of 8. When the icon row is selected, the selection of L[6:0] is limited to steps of 16. When a partial mode is selected, the selection of L[6:0] is also limited in steps. In addition, the selection of L[6:0] = 72 is not allowed when the icon row is enabled or disabled. The initial row can, in turn, be set by C[6:0], see Table 13. Row 0 cannot be set to icon row 79 when enabled. An example of the mapping from the RAM content to the display is shown in Figure 35. The content of the RAM is not modified. This feature allows, for instance, screen scrolling without rewriting the RAM. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 49 of 94 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors PCF8811 Product data sheet VHWLQLWLDOGLVSOD\OLQHDQGVWDUWURZZKHQ0< ;DGGUHVV 5$0 Rev. 6 — 10 February 2015 All information provided in this document is subject to legal disclaimers. / & 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ 5RZ PJZ Fig 35. Programming the L[6:0] address and C[6:0] address when MY = 0 PCF8811 50 of 94 © NXP Semiconductors N.V. 2015. All rights reserved. 80 x 128 pixels matrix LCD driver 'LVSOD\ PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 12.9 Bias levels The PCF8811 is only a MRA (Multiple Row Addressing) driver and does not support Alt-Pleshko. The bias levels for an MRA driving method with p = 8 are given in Figure 36 when Gmax and F have the same value. The value p defines the number of rows which are simultaneously selected. 9/&' *PD[ ) 9/&' 9B+ *PD[ 9B+ *PD[ 9B+ *PD[ 9& 9& 9B/ *PD[ 9B/ *PD[ 9B/ *PD[ 966 *PD[ ) 966 PJZ Fig 36. Bias levels for an MRA system with p = 8 and Gmax = F The row voltage F depends on the multiplex rate selected (number of rows N), the threshold voltage of the liquid (VTH), the number of simultaneously selected rows (p), and the multiplexibility (m): N m m–N 1 F = ------- V TH ---- ----------------------------------2 m–1 p (1) Concerning the plus/minus sign within Equation 1: The PCF8811is designed to take the lowest possible VLCD. Accordingly, the plus/minus sign is chosen in Equation 1. If m = N, the term after the plus/minus sign becomes 0 and disappears from the equation. For specific displays, m could be larger than N: e.g. if the liquid-crystal material used allows multiplexing of more rows than denoted by N, then the equation for F can be used with the minus sign. This leads to a lower row voltage and a higher column voltage. As a consequence, the necessary supply voltage, which would be required for Alt-Pleshko driving, can be reduced for displays with m > N by using PCF8811 with MRA. The column voltages are situated around the common level VC. The column voltage levels are equidistant from each other. In Table 24, the column voltage levels are given as a function of F. The row voltages (F) are not necessarily larger than the column voltages. This depends on the number of rows which are selected, the multiplexibility, and the value of p. However, the PCF8811 is designed in such a way that the maximum column voltages are always equal to the row voltages. In Table 24, the VLCD and the different bias levels are given for the PCF8811. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 51 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 24. F = Gmax. Bias levels for MRA driving method Symbol Bias voltages DC shifted bias voltages VLCD F VLCD V3_H F p – 2 ---------------------------------m– m–N V LCD p – 2 ------------- 1 + ---------------------------------- 2 m – m – N V2_H F p – 4 ---------------------------------m– m–N V LCD p – 4 ------------- 1 + ---------------------------------- 2 m – m – N V1_H F p – 6 ---------------------------------m– m–N V LCD p – 6 ------------- 1 + ---------------------------------- 2 m – m – N VC 0 V LCD -----------2 V1_L F – p – 6 ---------------------------------m– m–N V LCD p – 6 ------------- 1 – ---------------------------------- 2 m – m – N V2_L V LCD p – 4 ------------- 1 – ---------------------------------- 2 m – m – N F – p – 4 ---------------------------------m– m–N V3_L F – p – 2 ---------------------------------m– m–N V LCD p – 2 ------------- 1 – ---------------------------------- 2 m – m – N VSS F VSS The parameter F in Table 24 is a mathematical function that can produce positive values only. The resulting bias voltages in Figure 36 and Table 24 can have both positive and negative values, with the largest absolute value equal to F. However, the PCF8811 uses only positive supplies. If the calculated F values get DC-shifted such that all values are positive, the common voltage VC must be equal F. Then the DC-shifted bias voltages are not range from F to +F, but from 0 to 2F and thus VLCD is like in Equation 2: (2) V LCD = 2F Table 25. Relationship between multiplex rates and bias setting variables without icon row Multiplex rate PCF8811 Product data sheet Variable N m p 1:16 16 25 2 1:24 24 49 2 1:32 32 81 2 1:40 40 49 4 1:48 48 64 4 1:56 56 81 4 1:64 64 64 8 1:72 72 81 8 1:80 80 81 8 All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 52 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver The bias system settings for different display modes are given in Table 25. All bias levels can be calculated by using the third column of Table 24 and the variables given in Table 25. Programming of the bias levels is not necessary in the PCF8811. The selection of the appropriate bias level voltages for each display mode is made automatically. Only the appropriate VLCD voltage must be programmed according to Equation 1 and Equation 2 for the display modes listed in Table 25. The variables for calculating VLCD, when the icon row is enabled, are given in Table 26. The icon row can only be addressed in the extended command set. The PCF8811 allows the value of p for certain multiplex rates to be chosen manually. This is only possible for the multiplex rates 1:64 and 1:80. If other multiplex rates are chosen, the PCF8811 determines the optimum value of p. By setting the value of p manually, a compromise can be made between contrast and power consumption with certain liquids for the high multiplex rates 1:64 and 1:80. However, care must be taken that the liquid which is chosen ensures that the row voltages (F) and the maximum column voltages are equal. Table 26. Relationship between multiplex rates and bias setting variables with the icon row (only extended command set) Multiplex rate Variable N m p 1:16 24 49 2 1:32 40 49 4 1:48 56 81 8 1:64 80 81 8 1:80 80 81 8 12.10 Set VOP value For multiplex rate 1:80, the optimum operation voltage of a liquid can be calculated with the variables given in Table 26, Equation 1 and Equation 2, where VTH is the threshold voltage of the liquid crystal material used. 2 80 81 – 81 – 80 V LCD = ------- V TH ------ ---------------------------------------- = 4.472 V TH 2 8 81 – 1 (3) The programming method for the VOP value is implemented differently in the basic command set compared to the extended command set. In the basic command set two commands are sent to the PCF8811: namely VPR[5:0] and VOFF[2:0]. In the extended command set, only one command VPR[7:0] is sent to the PCF8811. The programming of VOP in the basic command set can be used when the PCF8811 is used as a replacement for an IAPT (Improved Alt-Pleshko Technique) LCD driver. The ROM look-up table Table 29 shows the possible values for VOFF[2:0], VPR[5:0], VOP[7:0] and VLCD. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 53 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver (;7 935>@ 00923&$/>@ (;7 935>@ 92))>@ 926>@ E D (;7 9/&' URPBDGG>@ /22.83 7$%/( 520 923>@ PJZ Fig 37. Setting of VOP in the basic and extended command set 12.10.1 Basic command set The VLCD at T = TCUT in the basic command set is determined by the conversion in the ROM look-up table with the programmed values of VPR[5:0] and VOFF[2:0]. It can, additionally, be adjusted with the VLCD offset pins VOS[4:0] to obtain the optimum optical performance. Example: To get the value of 6 V for VLCD, the following values (see Table 27) have to be taken: Table 27. Example values of VPR, VOP and VOFF for VLCD = 6 V Register Value in Table 29 Binary value VPR[5:0] 15 0 1111 VOP[7:0] 100 110 0100 VOFF[2:0] 010 010 Instead of using the VLCD offset pins (VOS[4:0]) the VLCD can be adjusted with the module maker calibration setting MMVOPCAL[4:0], see Section 19. V LCD T = T CUT = a + V OS [4:0] + V OP [7:0] b (4) Where: • T CUT is a reference temperature, see Section 12.11 • a is a fixed constant value, see Table 28 • b is a fixed constant value, see Table 28 • V OP 7:0 is the result of the conversion table • V OS 4:0 /MMVOPCAL 4:0 is the value of the offset VLCD pins or the value stored in the OTP cells PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 54 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 28. PCF8811 Product data sheet Parameters of VLCD for the basic and extended command set Symbol Value Unit TCUT 40 C b 0.03 V a 3 V All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 55 of 94 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors PCF8811 Product data sheet Table 29. ROM look-up table with values of VOFF, VPR, VOP and VLCD VOFF[000] VOFF[001] VOFF[010] VOFF[011] VOFF[100] Rev. 6 — 10 February 2015 All information provided in this document is subject to legal disclaimers. VOFF[111] VPR VOP VLCD VPR VOP VLCD VPR VOP VLCD VPR VOP VLCD VPR VOP VLCD [5:0] [7:0] (V) [5:0] [7:0] (V) [5:0] [7:0] (V) [5:0] [7:0] (V) [5:0] [7:0] (V) VPR VOP VLCD [5:0] [7:0] (V) VPR VOP VLCD [5:0] [7:0] (V) VPR VOP VLCD [5:0] [7:0] (V) 0 13 3.39 0 48 4.44 0 82 5.46 0 116 6.48 0 150 7.5 0 185 8.55 0 219 9.57 0 253 10.59 1 14 3.42 1 49 4.47 1 83 5.49 1 118 6.54 1 152 7.56 1 187 8.61 1 221 9.63 1 256 10.68 2 15 3.45 2 50 4.5 2 84 5.52 2 119 6.57 2 154 7.62 2 189 8.67 2 223 9.69 2 256 10.68 3 15 3.45 3 51 4.53 3 86 5.58 3 121 6.63 3 156 7.68 3 191 8.73 3 226 9.78 3 256 10.68 4 16 3.48 4 52 4.56 4 87 5.61 4 122 6.66 4 157 7.71 4 192 8.76 4 228 9.84 4 256 10.68 5 17 3.51 5 53 4.59 5 88 5.64 5 123 6.69 5 159 7.77 5 194 8.82 5 230 9.9 5 256 10.68 6 18 3.54 6 54 4.62 6 89 5.67 6 125 6.75 6 161 7.83 6 196 8.88 6 232 9.96 6 256 10.68 7 19 3.57 7 55 4.65 7 90 5.7 7 126 6.78 7 162 7.86 7 198 8.94 7 234 10.02 7 256 10.68 8 19 3.57 8 56 4.68 8 92 5.76 8 128 6.84 8 164 7.92 8 200 9 8 236 10.08 8 256 10.68 9 20 3.6 9 57 4.71 9 93 5.79 9 129 6.87 9 166 7.98 9 202 9.06 9 239 10.17 9 256 10.68 10 21 3.63 10 58 4.74 10 94 5.82 10 131 6.93 10 167 8.01 10 204 9.12 10 241 10.23 10 256 10.68 11 22 3.66 11 59 4.77 11 95 5.85 11 132 6.96 11 169 8.07 11 206 9.18 11 243 10.29 11 256 10.68 12 22 3.66 12 60 4.8 12 97 5.91 12 134 7.02 12 171 8.13 12 208 9.24 12 245 10.35 12 256 10.68 13 23 3.69 13 61 4.83 13 98 5.94 13 135 7.05 13 173 8.19 13 210 9.3 13 247 10.41 13 256 10.68 14 24 3.72 14 62 4.86 14 99 5.97 14 137 7.11 14 174 8.22 14 212 9.36 14 249 10.47 14 256 10.68 15 25 3.75 15 63 4.89 15 100 6 15 138 7.14 15 176 8.28 15 214 9.42 15 252 10.56 15 256 10.68 16 25 3.75 16 64 4.92 16 102 6.06 16 140 7.2 16 178 8.34 16 216 9.48 16 254 10.62 16 256 10.68 17 26 3.78 17 65 4.95 17 103 6.09 17 141 7.23 17 179 8.37 17 218 9.54 17 256 10.68 17 256 10.68 18 27 3.81 18 66 4.98 18 104 6.12 18 143 7.29 18 181 8.43 18 220 9.6 18 256 10.68 18 256 10.68 19 28 3.84 19 66 4.98 19 105 6.15 19 144 7.32 19 183 8.49 19 221 9.63 19 256 10.68 19 256 10.68 20 29 3.87 20 68 5.04 20 106 6.18 20 145 7.35 20 184 8.52 20 223 9.69 20 256 10.68 20 256 10.68 21 29 3.87 21 69 5.07 21 108 6.24 21 147 7.41 21 186 8.58 21 225 9.75 21 256 10.68 21 256 10.68 22 30 3.9 22 70 5.1 22 109 6.27 22 148 7.44 22 188 8.64 22 227 9.81 22 256 10.68 22 256 10.68 23 31 3.93 23 71 5.13 23 110 6.3 23 150 7.5 23 190 8.7 23 229 9.87 23 256 10.68 23 256 10.68 24 32 3.96 24 72 5.16 24 111 6.33 24 151 7.53 24 191 8.73 24 231 9.93 24 256 10.68 24 256 10.68 25 32 3.96 25 73 5.19 25 113 6.39 25 153 7.59 25 193 8.79 25 233 9.99 25 256 10.68 25 256 10.68 26 33 3.99 26 74 5.22 26 114 6.42 26 154 7.62 26 195 8.85 26 235 10.05 26 256 10.68 26 256 10.68 27 34 4.02 27 75 5.25 27 115 6.45 27 156 7.68 27 196 8.88 27 237 10.11 27 256 10.68 27 256 10.68 28 35 4.05 28 76 5.28 28 116 6.48 28 157 7.71 28 198 8.94 28 239 10.17 28 256 10.68 28 256 10.68 PCF8811 VOFF[110] 80 x 128 pixels matrix LCD driver 56 of 94 © NXP Semiconductors N.V. 2015. All rights reserved. VOFF[101] xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx ROM look-up table with values of VOFF, VPR, VOP and VLCD …continued VOFF[000] VOFF[001] VOFF[010] VOFF[011] VOFF[100] VPR VOP VLCD VPR VOP VLCD VPR VOP VLCD VPR VOP VLCD VPR VOP VLCD [5:0] [7:0] (V) [5:0] [7:0] (V) [5:0] [7:0] (V) [5:0] [7:0] (V) [5:0] [7:0] (V) VOFF[101] VOFF[110] VOFF[111] VPR VOP VLCD [5:0] [7:0] (V) VPR VOP VLCD [5:0] [7:0] (V) VPR VOP VLCD [5:0] [7:0] (V) Rev. 6 — 10 February 2015 All information provided in this document is subject to legal disclaimers. 4.05 29 77 5.31 29 118 6.54 29 159 7.77 29 200 9 29 241 10.23 29 256 10.68 29 256 10.68 36 4.08 30 78 5.34 30 119 6.57 30 160 7.8 30 201 9.03 30 243 10.29 30 256 10.68 30 256 10.68 31 37 4.11 31 79 5.37 31 120 6.66 31 162 7.86 31 203 9.09 31 245 10.35 31 256 10.68 31 256 10.68 32 38 4.14 32 80 5.4 32 121 6.63 32 163 7.89 32 205 9.15 32 247 10.41 32 256 10.68 32 256 10.68 33 39 4.17 33 81 5.43 33 123 6.69 33 165 7.95 33 207 9.21 33 249 10.47 33 256 10.68 33 256 10.68 34 39 4.17 34 82 5.46 34 124 6.72 34 166 7.98 34 208 9.24 34 250 10.5 34 256 10.68 34 256 10.68 35 40 4.2 35 83 5.49 35 125 6.75 35 167 8.01 35 210 9.3 35 252 10.56 35 256 10.68 35 256 10.68 36 41 4.23 36 84 5.52 36 126 6.78 36 169 8.07 36 212 9.36 36 254 10.62 36 256 10.68 36 256 10.68 37 42 4.26 37 85 5.55 37 127 6.81 37 170 8.1 37 213 9.39 37 256 10.68 37 256 10.68 37 256 10.68 38 42 4.26 38 86 5.58 38 129 6.87 38 172 8.16 38 215 9.45 38 256 10.68 38 256 10.68 38 256 10.68 39 43 4.29 39 87 5.61 39 130 6.9 39 173 8.19 39 217 9.51 39 256 10.68 39 256 10.68 39 256 10.68 40 44 4.32 40 88 5.64 40 131 6.93 40 175 8.25 40 218 9.54 40 256 10.68 40 256 10.68 40 256 10.68 41 45 4.35 41 89 5.67 41 132 6.96 41 176 8.28 41 220 9.6 41 256 10.68 41 256 10.68 41 256 10.68 42 45 4.35 42 90 5.7 42 134 7.02 42 178 8.34 42 222 9.66 42 256 10.68 42 256 10.68 42 256 10.68 43 46 4.38 43 91 5.73 43 135 7.05 43 179 8.37 43 224 9.72 43 256 10.68 43 256 10.68 43 256 10.68 44 47 4.41 44 92 5.76 44 136 7.08 44 181 8.43 44 225 9.75 44 256 10.68 44 256 10.68 44 256 10.68 45 48 4.44 45 93 5.79 45 137 7.11 45 182 8.46 45 227 9.81 45 256 10.68 45 256 10.68 45 256 10.68 46 48 4.44 46 94 5.82 46 139 7.17 46 184 8.52 46 229 9.87 46 256 10.68 46 256 10.68 46 256 10.68 47 49 4.47 47 95 5.85 47 140 7.2 47 185 8.55 47 230 9.9 47 256 10.68 47 256 10.68 47 256 10.68 48 50 4.5 48 96 5.88 48 141 7.23 48 187 8.61 48 232 9.96 48 256 10.68 48 256 10.68 48 256 10.68 49 51 4.53 49 97 5.91 49 142 7.26 49 188 8.64 49 234 10.02 49 256 10.68 49 256 10.68 49 256 10.68 50 52 4.56 50 98 5.94 50 143 7.29 50 189 8.67 50 235 10.05 50 256 10.68 50 256 10.68 50 256 10.68 51 52 4.56 51 99 5.97 51 145 7.35 51 191 8.73 51 237 10.11 51 256 10.68 51 256 10.68 51 256 10.68 52 53 4.59 52 100 6 52 146 7.38 52 192 8.76 52 239 10.17 52 256 10.68 52 256 10.68 52 256 10.68 53 54 4.62 53 101 6.03 53 147 7.41 53 194 8.82 53 241 10.23 53 256 10.68 53 256 10.68 53 256 10.68 54 55 4.65 54 102 6.06 54 148 7.44 54 195 8.85 54 242 10.26 54 256 10.68 54 256 10.68 54 256 10.68 55 55 4.65 55 103 6.09 55 150 7.5 55 197 8.91 55 244 10.32 55 256 10.68 55 256 10.68 55 256 10.68 56 56 4.68 56 104 6.12 56 151 7.53 56 198 8.94 56 246 10.38 56 256 10.68 56 256 10.68 56 256 10.68 57 57 4.71 57 105 6.15 57 152 7.56 57 200 9 57 247 10.41 57 256 10.68 57 256 10.68 57 256 10.68 PCF8811 35 30 80 x 128 pixels matrix LCD driver 57 of 94 © NXP Semiconductors N.V. 2015. All rights reserved. 29 NXP Semiconductors PCF8811 Product data sheet Table 29. xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx ROM look-up table with values of VOFF, VPR, VOP and VLCD …continued VOFF[000] VOFF[001] VOFF[010] VOFF[011] VOFF[100] VPR VOP VLCD VPR VOP VLCD VPR VOP VLCD VPR VOP VLCD VPR VOP VLCD [5:0] [7:0] (V) [5:0] [7:0] (V) [5:0] [7:0] (V) [5:0] [7:0] (V) [5:0] [7:0] (V) VOFF[101] VOFF[110] VOFF[111] VPR VOP VLCD [5:0] [7:0] (V) VPR VOP VLCD [5:0] [7:0] (V) VPR VOP VLCD [5:0] [7:0] (V) 58 58 4.74 58 105 6.15 58 153 7.59 58 201 9.03 58 249 10.47 58 256 10.68 58 256 10.68 58 256 10.68 59 58 4.74 59 107 6.21 59 155 7.65 59 203 9.09 59 251 10.53 59 256 10.68 59 256 10.68 59 256 10.68 60 59 4.77 60 108 6.24 60 156 7.68 60 204 9.12 60 252 10.56 60 256 10.68 60 256 10.68 60 256 10.68 61 60 4.8 61 109 6.27 61 157 7.71 61 206 9.18 61 254 10.62 61 256 10.68 61 256 10.68 61 256 10.68 62 61 4.83 62 110 6.3 62 158 7.74 62 207 9.21 62 256 10.68 62 256 10.68 62 256 10.68 62 256 10.68 63 62 4.86 63 111 6.33 63 160 7.8 63 209 9.27 63 256 10.68 63 256 10.68 63 256 10.68 63 256 10.68 NXP Semiconductors PCF8811 Product data sheet Table 29. Rev. 6 — 10 February 2015 All information provided in this document is subject to legal disclaimers. PCF8811 80 x 128 pixels matrix LCD driver 58 of 94 © NXP Semiconductors N.V. 2015. All rights reserved. PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 12.10.2 Extended command set The VLCD at T = TCUT is calculated using Equation 5. In the extended command set, VPR[7:0] is the same value as VOP[7:0]. It can additionally be adjusted with the VLCD offset pins VOS[4:0] to obtain the optimum optical performance. Instead of using the VLCD offset pins (VOS[4:0]) the VLCD can be adjusted with the module maker calibration setting MMVOPCAL[4:0], see Section 19. V LCD T = T CUT = a + V OS [4:0] + V OP [7:0] b (5) Where: • T CUT is a reference temperature, see Section 12.11 • a is a fixed constant value, see Table 28 • b is a fixed constant value, see Table 28 • V PR 7:0 is the programmed VOP value • V OS 4:0 /MMVOPCAL 4:0 is the value of the offset VLCD pins or the value stored in the OTP cells As the programming range for the internally generated VLCD allows values above the maximum allowed VLCD (9 V) the user has to ensure while setting the VPR register and selecting the Temperature Compensation (TC), that under all conditions and including all tolerances the VLCD remains below 9.0 V. This is valid for the two different command sets. PJW 9 /&' E D )' )( )) 9 23 VOP[7:0] programming (00h to FFh). Fig 38. VLCD programming of the PCF8811 PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 59 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 12.11 Temperature control Due to the temperature dependency of the viscosity of the liquid crystals, the LCD controlling voltage, VLCD, might have to be increased at lower temperatures to maintain optimum contrast. You can calculate the VLCD at a specific temperature for both command sets. VLCD (at T = TCUT) is given by Equation 4 or Equation 5 depending on the command set which is used. V LCD T = V LCD T = T CUT 1 + T – T CUT TC (6) In the extended command set and basic command set, 8 different temperature coefficients are available, see Figure 39. 9/&' 7&87 7 PJZ Fig 39. Temperature coefficients The typical values of the different temperature coefficients are given in Section 16. The coefficients are proportional to the programmed VLCD. The basic and extended command set differ in the way that the temperature coefficients can be accessed. In the basic command set, only one temperature coefficient is available. However, the possibility exists to program the default temperature coefficient with OTP programming, see Section 19. In the extended command set, the different temperature coefficients are selected by the interface with 3 bits TC[2:0]. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 60 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 13. Internal circuitry 9/&'287 9'' 9/&'6(16( 9'' 9/&',1 966 5 5 & & 9'' 7 7 '% '%6'$7$ (;7 '& 926 926 '6 26& 0) 5(6 0) 9''WLHRII 0) 966WLHRII 36 9273352* 36 6&/+6&( 36 6'$+ 6'$+287 (5' 5: 966 3&) DDP Fig 40. Device protection diagrams PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 61 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 14. Safety notes CAUTION This device is sensitive to ElectroStatic Discharge (ESD). Observe precautions for handling electrostatic sensitive devices. Such precautions are described in the ANSI/ESD S20.20, IEC/ST 61340-5, JESD625-A or equivalent standards. CAUTION Static voltages across the liquid crystal display can build up when the LCD supply voltage (VLCD) is on while the IC supply voltage (VDD) is off, or vice versa. This may cause unwanted display artifacts. To avoid such artifacts, VLCD and VDD must be applied or removed together. CAUTION Semiconductors are light sensitive. Exposure to light sources can cause the IC to malfunction. The IC must be protected against light. The protection must be applied to all sides of the IC. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 62 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 15. Limiting values Table 30. Limiting values[1] In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions VDD1 supply voltage 1 general VDD2 supply voltage 2 for internal voltage generator [2] VDD3 supply voltage 3 for internal voltage generator [2] Unit 0.5 +6.5 V 0.5 +4.5 V 0.5 +4.5 V VLCD LCD supply voltage 0.5 +10 V input voltage 0.5 +6.5 V VOTPPROG voltage applied to pin VOTPPROG 0.5 +12 V II input current DC level 10 +10 mA IO output current DC level 10 +10 mA ISS ground supply current 50 +50 mA Ptot total power dissipation - 300 mW P/out power dissipation per output VESD electrostatic discharge voltage Tstg Product data sheet Max Vi Ilu PCF8811 Min - 30 mW HBM [3] - 3000 V MM [4] - 250 V latch-up current [5] - 200 mA storage temperature [6] 65 +150 C [1] Parameters are valid over the whole operating temperature range unless otherwise specified. All voltages are referenced to VSS unless otherwise specified. [2] For the internal voltage multiplier. [3] Pass level; Human Body Model (HBM), according to Ref. 6 “JESD22-A114”. [4] Pass level; Machine Model (MM), according to Ref. 7 “JESD22-A115”. [5] Pass level; latch-up testing according to Ref. 8 “JESD78” at maximum ambient temperature (Tamb(max)). [6] According to the store and transport requirements (see Ref. 10 “UM10569”) the devices have to be stored at a temperature of +8 C to +45 C and a humidity of 25 % to 75 %. All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 63 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 16. Static characteristics Table 31. Static characteristics VDD1 = 1.7 V to 3.3 V; VSS = 0 V; VLCD = 3 V to 9 V; Tamb = 40 C to +85 C; unless otherwise specified. Symbol Parameter VDD1 supply voltage 1 Conditions Min Typ Max Unit general 1.7 - 3.3 V basic command set; when using ROM look-up table, see Section 12.10 2 - 3.3 V for internal voltage multiplier 1.8 - 3.3 V VDD2 supply voltage 2 VDD3 supply voltage 3 for internal voltage multiplier 1.8 - 3.3 V VLCDIN LCD supply voltage LCD voltage externally supplied (voltage multiplier disabled) 3 - 9 V - - 9 V 300 - +300 mV 70 - +70 mV VLCDOUT voltage multiplier output voltage LCD voltage internally generated (voltage multiplier enabled) VLCD(tol) without calibration IDD1 IDD2 IDD3 IDD(tot) tolerance of generated VLCD supply current 1 supply current 2 supply current 3 total supply current [1] [2] with calibration general for internal voltage multiplier for internal voltage multiplier VDD1 + VDD2 + VDD3 [3][4] 0.5 1.5 5 A [4][5] 15 25 50 A [3][4] 0 0.5 1 A [4][5] 130 150 200 A [3][4] 0 0.5 1 A [4][5] 130 150 200 A [4][5] 145 175 250 A Logic inputs; MF[2:0], VOS[4:0], DS0, EXT, PS[2:0], RES and OSC Vi input voltage VSS 0.5 VIL LOW-level input voltage VSS - 0.2VDD1 V VIH HIGH-level input voltage 0.8VDD1 - VDD1 V IL leakage current 1 - +1 A VI = VDD or VSS VDD1 + 0.5 V Column and row outputs Rcol column output resistance C0 to C127; VLCD = 5 V - - 5 k Rrow row output resistance R0 to R80; VLCD = 5 V - - 5 k Vbias(col) bias tolerance voltage C0 to C127 100 0 +100 mV R0 to R80 100 0 +100 mV Vbias(row) bias tolerance voltage LCD supply voltage multiplier TC0 LCD voltage temperature coefficient 0 - 0 - 1⁄ C TC1 LCD voltage temperature coefficient 1 - 0.16 103 - 1⁄ C TC2 LCD voltage temperature coefficient 2 - 0.33 103 - 1⁄ C TC3 LCD voltage temperature coefficient 3 - 0.50 103 - 1⁄ C TC4 LCD voltage temperature coefficient 4 - 0.66 103 - 1⁄ C PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 64 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 31. Static characteristics …continued VDD1 = 1.7 V to 3.3 V; VSS = 0 V; VLCD = 3 V to 9 V; Tamb = 40 C to +85 C; unless otherwise specified. Symbol Parameter Conditions Min Typ 103 Max Unit - 1⁄ C TC5 LCD voltage temperature coefficient 5 - 0.833 TC6 LCD voltage temperature coefficient 6 - 1.25 103 - 1⁄ C TC7 LCD voltage temperature coefficient 7 - 1.66 103 - 1⁄ C [6] Parallel interface; VDD1 = 1.8 V to 3.3 V Vi input voltage 0.5 - VDD1 + 0.5 V VIL LOW-level input voltage VSS - 0.2VDD1 V VIH HIGH-level input voltage 0.8VDD1 - VDD1 V Serial interface; VDD1 = 1.7 V to 3.3 V Vi input voltage 0.5 - VDD1 + 0.5 V VIL LOW-level input voltage VSS - 0.2VDD1 V VIH HIGH-level input voltage 0.8VDD1 - VDD1 V 0.5 - +3.3 V 3 - - mA 2 - - mA I2C-bus interface; VDD1 = 1.8 V to 3.3 V input voltage Vi IOL(SDAH) LOW-level output current VOL = 0.4 V; VDD1 2 V on pin SDAH VOL = 0.2 VDD1; VDD1 2 V VIL LOW-level input voltage VSS - 0.3VDD1 V VIH HIGH-level input voltage 0.7VDD1 - VDD1 V VSS - 0.2VDD1 V 0.8VDD1 - VDD1 V Output levels for all interfaces VOL LOW-level output voltage IOL = 0.5 mA VOH HIGH-level output voltage IOH = 0.5 mA [1] The maximum possible VLCD voltage that can be generated is dependent on voltage, temperature and (display) load. [2] Valid for values of temperature, VPR and TC used at calibration. [3] During power-down, all static currents are switched off. [4] Conditions are: VDD1 = 1.8 V, VDD2 = 2.7 V, VLCD = 8.05 V, voltage multiplier 4 VDD2, inputs at VDD1 or VSS, interface inactive, internal VLCD generation, VLCD output is loaded by 10 A and Tamb = 25 C. [5] Normal mode. [6] TC7 can only be used when VDD2 = VDD3 = 2.4 V or higher. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 65 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 17. Dynamic characteristics Table 32. Dynamic characteristics[1] VDD1 = 1.7 V to 3.3 V; VSS = 0 V; VLCD 9 V; Tamb = 40 C to +85 C; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit fext external frequency external clock - 200 - kHz ffr frame frequency Tamb = 25 C; VDD1 = 2.4 V tVHRL VDD to RES LOW see Figure 48 tRW RES LOW pulse width see Figure 48 [1] All specified timings are based on 20 % and 80 % of VDD. [2] RES can be LOW before VDD goes HIGH. [2] 54 60 66 Hz 43 58 73 Hz 0 - 1 s 500 - - ns 17.1 Parallel interface timing characteristics Table 33. Parallel interface (6800 series) timing characteristics VDD1 = 1.8 V to 3.3 V; VSS = 0 V; VLCD 9 V; Tamb = 40 C to +85 C; unless otherwise specified, see Figure 41. PCF8811 Product data sheet Symbol Parameter Min Max Unit tSU;DC data/command set-up time 40 - ns tHD;DC data/command hold time 20 - ns Tcyc(DS) data strobe cycle time 1000 - ns tDS(L) data strobe LOW time 320 - ns tDS(H) data strobe HIGH time 300 - ns tSU;RW read/write set-up time 280 - ns tHD;RW read/write hold time 20 - ns tSU;CE chip enable set-up time 280 - ns tHD;CE chip enable hold time 0 - ns tSU;DAT data set-up time 20 - ns tHD;DAT data hold time 40 - ns tDAT;ACC data output access time - 280 ns tDAT;OH data output disable time - 20 ns All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 66 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 5::5 W68&( W685: W+'&( W+'5: W68'& W+''& '& ( 7F\F'6 W'6/ W'6+ 6&( W68'$7 W+''$7 'WR' :ULWH W'$7$&& W'$72+ 'WR' 5HDG DDD Fig 41. Parallel interface timing; 6800 series PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 67 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 17.2 Serial interface timing characteristics Table 34. Serial interface timing characteristics[1] VDD1 = 1.8 V to 3.3 V; VSS = 0 V; VLCD 9 V; Tamb = 40 C to +85 C; unless otherwise specified, see Figure 42, Figure 43, Figure 44 and Figure 45. Symbol Parameter Min Max Unit fSCLK clock frequency - 9.00 MHz Tcyc clock cycle SCLK 111 - ns tPWH1 SCLK pulse width HIGH 45 - ns tPWL1 SCLK pulse width LOW 45 - ns tS2 SCE set-up time 50 - ns tH2 SCE hold time 45 - ns tPWH2 SCE minimum HIGH time 50 - ns 50 - ns tH5 SCE start hold time tS3 data/command set-up time 50 - ns tH3 data/command hold time 50 - ns tS1 SDATA set-up time 50 - ns tH1 SDATA hold time 50 - ns t1 SDO access time - 50 ns t2 SDO disable time - 50 ns t3 SCE hold time Product data sheet [3] 50 - ns SDO disable time [4] 25 100 ns Cb capacitive load for SDO [5] - 30 pF Rb series resistance for SDO [5] - 500 t4 PCF8811 [2] [1] All specified timings are based on 20 % and 80 % of VDD. [2] tH5 is the time from the previous SCLK rising edge (irrespective of the state of SCE) to the falling edge of SCE. [3] SDO disable time for SPI 3-line or 4-line. [4] SDO disable time for 3-line serial interface. [5] Maximum values are for fSCLK = 9 MHz. Series resistance includes ITO track + connector resistance + printed-circuit board. All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 68 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver W6 W+ W3:+ 6&( W+ W+ 7F\F W3:/ W6 W3:+ 6&/. W+ W6 6'$7$ PJZ Fig 42. 3-line serial interface timing W6 W+ W3:+ 6&( W6 W+ W+ W+ '& 7F\F W3:/ W3:+ W6 6&/. W6 W+ 6'$7$ PJZ Fig 43. 4-line serial interface timing PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 69 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 6&( W 6&/. W+ W6 6'$7$ W W 6'2 DDL Fig 44. Serial interface timing; SPI 3-line or 4-line (read mode) 6&( W 6&/. W+ W6 6'$7$ W W 6'2 DDL Fig 45. Serial interface timing; 3-line serial interface (read mode) PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 70 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 17.3 I2C-bus interface timing characteristics Table 35. I2C-bus characteristics; F/S-mode VDD1 = 1.8 V to 3.3 V; VSS = 0 V; VLCD 9 V; Tamb = 40 C to +85 C; unless otherwise specified[1], see Figure 46. Symbol Parameter fSCL Min Typ Max Unit SCL clock frequency 0 - 400 kHz tSU;STA set-up time for a repeated START condition 600 - - ns tHD;STA hold time (repeated) START condition 600 - - ns tLOW LOW period of the SCL clock 1300 - - ns tHIGH HIGH period of the SCL clock 600 - - ns tSU;DAT data set-up time 100 - - ns tHD;DAT data hold time 0 - 900 ns tr rise time of both SDA and SCL signals 20 + 0.1Cb - 300 ns tf fall time of both SDA and SCL signals 20 + 0.1Cb - 300 ns Cb capacitive load for each bus line - - 400 pF tSU;STO set-up time for STOP condition 600 - - ns tSP pulse width of spikes that must be suppressed by the input filter - - 50 ns tBUF bus free time between a STOP and START condition 1300 - - ns VnL noise margin at the LOW level for each connected device (including hysteresis) 0.1VDD1 - - V VnH noise margin at the HIGH level for each connected device (including hysteresis) 0.2VDD1 - - V [1] Conditions All specified timings are based on 20 % and 80 % of VDD. 6'$ W/2: WI W68'$7 WU WI W+'67$ W63 WU W%8) 6&/ 6 W+'67$ W+''$7 W+,*+ W6867$ 6U W68672 3 6 DDL S = start Sr = start repeated P = stop Fig 46. I2C-bus timing diagram (F/S-mode) PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 71 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 36. I2C-bus characteristics; Hs-mode VDD1 = 1.8 V to 3.3 V; VSS = 0 V; VLCD 9 V; Tamb = 40 C to +85 C; unless otherwise specified[1], see Figure 47. Symbol Parameter fSCLH SCLH clock frequency tSU;STA Conditions Cb = 100 pF (max) Cb = 400 pF[2] Unit Min Max Min Max 0 3.4 0 1.7 set-up time for a repeated START condition 160 - 160 - ns tHD;STA hold time (repeated) START condition 160 - 160 - ns tLOW LOW period of the SCLH clock 160 - 320 - ns tHIGH HIGH period of the SCLH clock 60 - 120 - ns tSU;DAT data set-up time 10 tHD;DAT data hold time MHz - 10 - ns 20[3] 70 20[3] 150 ns trCL rise time of SCLH signal 10 40 20 80 ns trCL1 rise time of SCLH signal after a repeated START condition and after an acknowledge bit 10 80 20 160 ns tfCL fall time of SCLH signal 10 40 20 80 ns trDA rise time of SDAH signal 10 80 20 160 ns tfDA fall time of SDAH signal 10 80 20 160 ns tSU;STO set-up time for STOP condition 160 - 160 - ns tSP pulse width of spikes that must be suppressed by the input filter SDAH and SCLH 0 5 0 5 ns Cb capacitive load for each bus line SDAH and SCLH lines 0 100 - 400 pF 0 400 - 400 pF [2] SDAH + SDA line and SCLH + SCL line VnL noise margin at the LOW level for each connected device (including hysteresis) 0.1VDD1 - 0.1VDD1 - V VnH noise margin at the HIGH level 0.2VDD2 - 0.2VDD2 - V for each connected device (including hysteresis) [1] All specified timings are based on 20 % and 80 % of VDD. [2] For bus line loads Cb between 100 pF and 400 pF the timing parameters must be linearly interpolated. [3] A device must internally provide a data hold time to bridge the undefined part between VIH and VIL of the falling edge of the SCLH signal. An input circuit with a threshold as low as possible for the falling edge of the SCLH signal minimizes this hold time. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 72 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 6U 6U WU'$ WI'$ 3 6'$+ W+''$7 W6867$ W68672 W+'67$ W68'$7 6&/+ WI&/ WU&/ WU&/ WU&/ W+,*+ W/2: W/2: W+,*+ PJN 0&6FXUUHQWVRXUFHSXOOXS 5SUHVLVWRUSXOOXS (1) Rising edge of the first SCLH clock pulse after an acknowledge bit. Fig 47. I2C-bus timing diagram (Hs-mode) 9'' W5: W5: 5(6 9'' W9+5/ W5: W5: 5(6 PJZ Fig 48. Reset timing PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 73 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 18. Application information Semiconductors are light sensitive. Exposure to light sources can cause the IC to malfunction. In this application, the IC must be protected against light. The protection has to be done on all sides of the IC, i.e. front, rear and all edges. The pinning of the PCF8811 has an optimum design for single plane wiring e.g. for chip-on-glass display modules. Display size: 80 128 pixels. For further application information, refer to NXP Semiconductors Application Note AN10170 Design guidelines for COG modules with NXP monochrome LCD drivers. 966 966 9'' 9'' 9'' 3&) 9/&'6(16( 9/&'287 9/&',1 ',63/$<îSL[HOV &9/&' ,2 &9'' 9'' 966 PJZ Fig 49. Application diagram: internal charge pump and a single supply 9'' ,2 966 966 9'' 9'' 9'' 3&) 9/&'6(16( 9/&'287 9/&',1 ',63/$<îSL[HOV &9'' &9/&' &9'' 9'' 966 PJZ Fig 50. Application diagram: internal charge pump and two separate supplies (VDD1 and VDD2) PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 74 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver ,2 966 966 9'' 9'' 9'' 3&) 9/&'6(16( 9/&'287 9/&',1 ',63/$<îSL[HOV &9'' 9'' 966 9/&',1 PJZ Fig 51. Application diagram: external high voltage The required minimum value for the external capacitors in an application with the PCF8811 are: CVLCD = 1.0 F to 4.7 F depending on the application. CVDD, CVDD1, CVDD2 = 1.0 F. For these capacitors, higher values can be used. 19. Support information 19.1 Module maker programming One Time Programmable (OTP) technology is implemented on the PCF8811. It enables the module maker to program some extended features of the PCF8811 after it has been assembled on an LCD module. Programming is made under the control of the interfaces and the use of one special pin. This pin must be made available on the module glass but do not need to be accessed by the set maker. The PCF8811 features 3 parameters programmable by the module maker: • VLCD calibration • Temperature coefficient selection • Seal bit 19.1.1 VLCD calibration The first feature included is the ability to adjust the VLCD voltage with a 5-bit code (MMVOPCAL). This code is implemented in two’s complement notation causing a positive or negative offset to the VPR register. This is in the same manner as the on-glass calibration pins VOS. In theory, both may be used together but it is recommended that the VOS pins are tied to VSS when OTP calibration is being used. This sets them to a default offset of zero. If both are used, then the addition of the two 5-bit numbers must not exceed a 5-bit result, PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 75 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver otherwise the resultant value is undefined. The final adder in the circuit has underflow and overflow protection. In the event of overflow, the output is clamped to 255; during an underflow the output is clamped to 0. The final control to the high-voltage multiplier, VOP, is the sum of all the calibration registers and pins. The VLCD Equation 4 or Equation 5 given in Section 12.10.1 or Section 12.10.2 must be extended to include the OTP calibration, as follows: V LCD T = T CUT = a + V OS [4:0] + MMVOPCAL[4:0] + V OP [7:0] b (7) The possible values for MMVOPCAL[4:0] and VOS[4:0] values are given in Table 37. Table 37. VOS/MMVOPCAL values in two’s complement notation Binary Decimal Binary Decimal 0 0000 0 1 1111 1 0 0001 +1 1 1110 2 0 0010 +2 1 1101 3 0 0011 +3 1 1100 4 0 0100 +4 1 1011 5 0 0101 +5 1 1010 6 0 0110 +6 1 1001 7 0 0111 +7 1 1000 8 0 1000 +8 1 0111 9 0 1001 +9 1 0110 10 0 1010 +10 1 0101 11 0 1011 +11 1 0100 12 0 1100 +12 1 0011 13 0 1101 +13 1 0010 14 0 1110 +14 1 0001 15 0 1111 +15 1 0000 16 2739/&'FDOLEUDWLRQELWRIIVHW UDQJH WR 00923&$/>@ ODVHUWULPSLQVELWRIIVHW UDQJH WR 926>@ 923>@ UDQJHWR WRKLJKYROWDJH JHQHUDWRU UDQJHWR XVDEOHUDQJHWR 935UHJLVWHUELWYDOXH PJX 935>@ Fig 52. VLCD calibration 19.1.2 Temperature coefficient selection The second feature is an OTP factory default setting for the temperature coefficient selection (MMTC) in the basic command set. This 3-bit value will be loaded from OTP after leaving the power-save mode or by the refresh command. The idea of this feature is PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 76 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver to provide, in the basic command set, the complete set of temperature coefficients without an additional command. In the extended command set, the temperature coefficient can be programmed as given in Table 21 and Table 31. 19.1.3 Seal bit The module maker programming is performed in a special mode: the calibration mode (CALMM). This mode is entered via a special interface command, CALMM, see Table 12 andTable 39. To prevent unwanted programming, a seal bit has been implemented which prevents the device from entering the calibration mode. This seal bit, once programmed, cannot be reversed so further changes in programmed values are not possible. Applying the programming voltages when not in CALMM mode has no effect on the programmed values. Table 38. Seal bit definition Seal bit Action 0 possible to enter calibration mode 1 calibration mode disabled 19.1.4 OTP architecture The OTP circuitry in the PCF8811 contains 9 bits of data: 5 for VLCD calibration (MMVOPCAL), 3 for the temperature coefficient default setting in the basic command set MMTC and 1 seal bit. The circuitry for 1-bit is called an OTP slice. Each OTP slice consists of 2 main parts: the OTP cell (a non-volatile memory cell) and the shift register cell (a flip-flop). The OTP cells are only accessible through their shift register cells: on the one hand both reading from and writing to the OTP cells is performed with the shift register cells, on the other hand only the shift register cells are visible to the rest of the circuit. The basic OTP architecture is shown in Figure 53. This OTP architecture allows the following operations: Reading data from the OTP cells — The content of the non-volatile OTP cells is transferred to the shift register where upon it may affect the PCF8811 operation. Writing data to the OTP cells — All 9 data bits are shifted into the shift register via the interface. The content of the shift register is then transferred to the OTP cells. There are some limitations related to storing data in these cells, see Section 19.1.7. Checking calibration without writing to the OTP cells — Shifting data into the shift register allows the effects on the VLCD voltage to be observed. The reading of data from the OTP cells is initiated by either: • Exit from power-save mode • The refresh command (power control) Remark: In both cases, the reading operation needs up to 5 ms to complete. The shifting of data into the shift register is performed in the special mode CALMM. In the PCF8811, the CALMM mode is entered by the CALMM command. Once in the CALMM mode the data is shifted into the shift register via the interface at the rate of 1-bit per command. After transmitting the last (9th) bit and exiting the CALMM mode, the serial PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 77 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver interface will return to the normal mode and all other commands can be sent. Care should be taken that 9 bits of data (or a multiple of 9) are always transferred before exiting the CALMM mode, otherwise the bits are in the wrong positions. In the shift register, the value of the seal bit is, like the others, always zero at reset. To ensure that the security feature (seal bit) works correctly, the CALMM command is disabled until a refresh has been performed. Once the refresh is completed, the seal bit value in the shift register is valid and permission to enter the CALMM mode can thus be determined. The 9 bits are shifted into the shift register in a predefined order: first 5 bits of MMVOPCAL[4:0], 3 bits for MMTC[2:0] and lastly the seal bit. The MSB is always first, thus the first bit shifted is MMVOPCAL[4] and the two last bits are MMTC[0] and the seal bit. '$7$727+(&,5&8,7)25 &21),*85$7,21$1'&$/,%5$7,21 273VOLFH 6+,)7 5(*,67(5 )/,3)/23 UHDGGDWD IURPWKH 273FHOO 6+,)7 5(*,67(5 '$7$ ,1387 6+,)7 5(*,67(5 ZULWHGDWD WRWKH 273FHOO 273&(//6 PJX 273&(// Fig 53. Basic OTP architecture 19.1.5 Interface commands These instructions are in addition to those indicated in Table 12. Table 39. Additional interface commands Instruction Pin Command byte Description EXT D/C R/W/WR DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 CALMM X[1] 0 0 1 0 0 0 0 0 1 0 enter CALMM mode Power control (refresh) X[1] 0 0 0 0 1 0 1 PC1 PC0 1 switch HVgen on/off to force a refresh of the shift register [1] X = value without meaning. 19.1.5.1 CALMM This instruction puts the device in calibration mode. This mode enables the shift register for loading and allows programming of the non-volatile OTP cells to take place. If the seal bit is set, then this mode cannot be accessed and the instruction is ignored. Once in calibration mode all commands are interpreted as shift register data. The mode can only be exited by sending data with DB7 set to logic 0. Reset also clears this mode. Each shift PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 78 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver register data byte is preceded by D/C = 0 and has only 2 significant bits, thus the remaining 6 bits are ignored. DB7 is the continuation bit (DB7 = 1 remain in CALMM mode, DB7 = 0 exit CALMM mode). DB0 is the data bit and its value is shifted into the OTP shift register (on the falling edge of SCLK). 19.1.5.2 Refresh The action of the refresh instruction is to force the OTP shift register to reload from the non-volatile OTP cells. This instruction takes up to 5 ms to complete. During this time, all other instructions may be sent. In the PCF8811, the refresh instruction is associated with the power control instruction so that the shift register is automatically refreshed every time the high voltage multiplier is enabled or disabled. If this instruction is sent while in power-save mode, the PC[1:0] bits are updated but the refreshing is ignored. 19.1.6 Example sequence for filling the shift register An example of the sequence of commands and data is shown in Table 40. In this example the shift register is filled with the following data: MMVOPCAL = 4 (1 1100b), MMTC = 2 (010b) and the seal bit is logic 0. It is assumed that the PCF8811 has just been reset. After transmitting the last bit the PCF8811 can either exit or remain in the CALMM mode, see Table 40, Step 1. While in CALMM mode the interface does not recognize commands in the normal sense. After this sequence has been applied, it is possible to observe the impact of the data shifted in. The described sequence is, however, not useful for OTP programming because the number of bits with the value logic 1 is greater than that allowed for programming, see Section 19.1.7. The shift register after this action is shown in Figure 54. Table 40. Sequence for filling the shift register; example 1 X = value without meaning. Step Pin EXT Command byte Action D/C R/W/WR DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 1 X 0 0 1 1 1 0 0 0 0 1 exit power-down 2 - - - - - - - - - - - wait 5 ms for refresh to take effect 3 X 0 0 1 0 0 0 0 0 1 0 enter CALMM mode 4 X 0 0 1 X X X X X X 1 shift in data; MMVOPCAL[4] is first bit [1] 5 X 0 0 1 X X X X X X 1 MMVOPCAL[3] 6 X 0 0 1 X X X X X X 1 MMVOPCAL[2] 7 X 0 0 1 X X X X X X 0 MMVOPCAL[1] 8 X 0 0 1 X X X X X X 0 MMVOPCAL[0] 9 X 0 0 1 X X X X X X 0 MMTC[2] 10 X 0 0 1 X X X X X X 1 MMTC[1] 11 X 0 0 1 X X X X X X 0 MMTC[0] 12 X 0 0 0 X X X X X X 0 seal bit; exit CALMM mode X X X 0 seal bit; remain in CALMM mode An alternative ending could be to stay in CALMM mode 13 [1] X 0 0 1 X X X The data for the bits is not in the correct shift register position until all bits have been sent. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 79 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 2736+,)75(*,67(5 VKLIWLQJ GLUHFWLRQ 6($/ %,7 /6% 007&>@ 06% /6% 00923&$/>@ 06% PJZ Fig 54. Shift register contents after example sequence, see Table 40 19.1.7 Programming flow Programming is achieved while in CALMM mode and with the application of the programming voltages. As mentioned previously, the data for programming the OTP cell is contained in the corresponding shift register cell. In order to program the corresponding OTP cell, the shift register cell must be loaded with a logic 1. If the shift register cell contains a logic 0, then no action takes place when the programming voltages are applied. Once programmed, an OTP cell cannot be de-programmed. An already programmed cell, i.e. an OTP cell containing a logic 1, must not be reprogrammed. During programming, a substantial current flows in the VLCDIN pin. For this reason, it is recommended to program only one OTP cell at a time by filling all but one shift register cells with logic 0.2 The programming specification refers to the voltages at the chip pins, contact resistance must therefore be considered by the user. An example sequence of commands and data for OTP programming is given in Table 41. It is assumed that the PCF8811 has just been reset. The order for programming cells is not significant. However, NXP Semiconductors recommends that the seal bit is programmed last. Once this bit has been programmed and the CALMM mode is exited, it is not possible to reenter the CALMM mode. Table 41. Sequence for filling the shift register; example 2 X = value without meaning. Step Pin Command byte Action EXT D/C R/W/WR DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 1 X 0 0 1 1 1 0 0 0 0 1 exit power-save 2 - - - - - - - - - - - wait 5 ms for refresh to take effect 3 X 0 0 1 0 1 0 1 0 0 1 reenter power-down (DON = 0) 4 X 0 0 1 0 0 0 0 0 1 0 enter CALMM mode 5 X 0 0 1 X X X X X X 1 shift in data; MMVOPCAL[4] is first bit 6 X 0 0 1 X X X X X X 1 MMVOPCAL[3] 7 X 0 0 1 X X X X X X 1 MMVOPCAL[2] 9 X 0 0 1 X X X X X X 0 MMVOPCAL[1] 10 X 0 0 1 X X X X X X 0 MMVOPCAL[0] 11 X 0 0 1 X X X X X X 0 MMTC[2] 12 X 0 0 1 X X X X X X 1 MMTC[1] 13 X 0 0 1 X X X X X X 0 MMTC[0] 2. The examples in Table 40 and Table 41 are not in line with this recommendation since more than one cell is set to 1 at a time. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 80 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 41. Sequence for filling the shift register; example 2 …continued X = value without meaning. Step Pin Command byte Action EXT D/C R/W/WR DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 14 X 0 0 1 X X X X X X 0 seal bit 15 - - - - - - - - - - - apply programming voltage at pins VOTPPROG and VLCDIN, see Section 19.1.8 Repeat steps 5 to 14 (9 bits, see Section 19.1.4) for each bit which must be programmed to 1; exit CALMM mode 16 - - - - - - - - - - - apply external reset 19.1.8 Programming specification Table 42. Programming specification See Figure 55. Symbol VOTPPROG Parameter Conditions voltage applied to pin VOTPPROG relative to VSS1 Min Typ Max Unit programming active [1] 11 11.5 12 V programming inactive [1] VSS 0.2 0 VSS + 0.2 V 9 9.5 10 V VDD2 0.2 VDD2 4.5 V - 850 1000 A voltage applied to pin VLCDIN relative to VSS1 programming active [1][2] programming inactive [1][2] ILCDIN current drawn by VLCDIN during programming when programming a single bit to logic 1 IVOTPPROG current drawn by VOTPPROG during programming - 100 200 A Tamb(PROG) ambient temperature during programming 0 25 40 C tSU;SCLK set-up time of internal data after last clock 1 - - s tHD;SCLK hold time of internal data before next clock 1 - - s tSU;VOTPPROG set-up time of VOTPPROG prior to programming 1 - 10 s tHD;VOTPPROG hold time of VOTPPROG after programming 1 - 10 ms 100 120 200 ms VLCDIN pulse width of programming voltage tPW [1] The voltage drop across the ITO track and zebra connector must be taken into account to guarantee a sufficiently high voltage at the chip pins. [2] The power-down mode (DON = 0 and DAL = 1) and CALMM mode must be active while the VLCDIN pin is being driven. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 81 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver W686&/. W+'6&/. 6&/. 99273352* 9/&',1 W68927352* W+'9273352* W3: PJZ Fig 55. Programming waveforms 20. Package outline Not applicable. 21. Handling information All input and output pins are protected against ElectroStatic Discharge (ESD) under normal handling. When handling Metal-Oxide Semiconductor (MOS) devices ensure that all normal precautions are taken as described in JESD625-A, IEC 61340-5 or equivalent standards. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 82 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 22. Packing information $ & [ ' ) % \ \ ( [ DDL Fig 56. Tray details 3&) PJZ Fig 57. Tray alignment PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 83 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Table 43. Tray dimensions See Figure 56. Symbol Description Value A pocket pitch in x direction 20.12 mm B pocket pitch in y direction 4.09 mm C pocket width in x direction 12.55 mm D pocket width in y direction 2.41 mm E tray width in x direction 50.8 mm F tray width in y direction 50.8 mm x number of pockets, x direction 2 y number of pockets, y direction 11 The orientation of the IC in a pocket is indicated by the position of the IC type name on the die surface with respect to the chamfer on the upper left corner of the tray. Refer to the bonding pin location diagram (Figure 2) for the orientation and position of the type name on the die surface. PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 84 of 94 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors PCF8811 Product data sheet 23. Appendix 23.1 LCD graphic driver selection Table 44. Selection of LCD graphic drivers Type name Max display resolution rows col. Rev. 6 — 10 February 2015 All information provided in this document is subject to legal disclaimers. Multiplex rates VDD1 (V) PCA8539DUG 18 100 1:12, 1:18 2.5 to 5.5 2.5 to 5.5 4 to 16 45 to 360[1] Y Y 40 to 105 I2C, SPI bare die Y PCF8539DUG 18 100 1:12, 1:18 2.5 to 5.5 2.5 to 5.5 4 to 16 45 to 360[1] Y Y 40 to 85 I2C, SPI bare die N bare die N bare die N PCF8531U 34 128 or 33 128 plus 128 icons 1:17, 1:26, 1:34 PCF8811U 80 128 or 79 129 plus 128 icons 1:16 to 1:80 2 to 3.3 in steps of 8 [1] VDD2 (V) VLCD (V) ffr (Hz) 1.8 to 5.5 2.5 to 4.5 4 to 9 1.8 to 3.3 3 to 9 VLCD (V) VLCD (V) Tamb (C) charge temperature pump compensat. Interface Package AECQ100 66 Y Y 40 to 85 I2C 30 to 60[1] Y Y 40 to 85 I2C, SPI, parallel Can be selected by command. PCF8811 80 x 128 pixels matrix LCD driver 85 of 94 © NXP Semiconductors N.V. 2015. All rights reserved. PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 24. Abbreviations Table 45. Acronym PCF8811 Product data sheet Abbreviations Description CDM Charged Device Model CMOS Complementary Metal-Oxide Semiconductor COG Chip-On-Glass DDRAM Double Data Random Access Memory ESD ElectroStatic Discharge HBM Human Body Model HV High Voltage IC Integrated Circuit ITO Indium Tin Oxide LCD Liquid Crystal Display LSB Least Significant Bit MM Machine Model MRA Multiple Row Addressing MSB Most Significant Bit MPU MicroProcessing Unit OTP One Time Programmable RAM Random Access Memory SPI Serial Peripheral Interface TC Temperature Coefficient TCP Tape Carrier Packages All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 86 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 25. References [1] AN10170 — Design guidelines for COG modules with NXP monochrome LCD drivers [2] AN11267 — EMC and system level ESD design guidelines for LCD drivers [3] AN10706 — Handling bare die [4] IEC 60134 — Rating systems for electronic tubes and valves and analogous semiconductor devices [5] IEC 61340-5 — Protection of electronic devices from electrostatic phenomena [6] JESD22-A114 — Electrostatic Discharge (ESD) Sensitivity Testing Human Body Model (HBM) [7] JESD22-A115 — Electrostatic Discharge (ESD) Sensitivity Testing Machine Model (MM) [8] JESD78 — IC Latch-Up Test [9] JESD625-A — Requirements for Handling Electrostatic-Discharge-Sensitive (ESDS) Devices [10] UM10569 — Store and transport requirements [11] UM10204 — I2C-bus specification and user manual PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 87 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 26. Revision history Table 46. Revision history Document ID Release date Data sheet status Change notice Supersedes PCF8811 v.6 20150210 Product data sheet - PCF8811 v.5 Modifications: • The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. • • • Legal texts have been adapted to the new company name where appropriate. Fixed typos Enhanced description of DS0, see Section 7.1.9 PCF8811 v.5 20100629 PCF8811 v.4 20080627 Product data sheet - PCF8811 v.3 PCF8811 v.3 20040517 Product specification - PCF8811 v.2 PCF8811 v.2 20021204 Product specification - PCF8811 v.1 PCF8811 v.1 20020814 Product specification - - PCF8811 Product data sheet Product data sheet - All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 PCF8811 v.4 © NXP Semiconductors N.V. 2015. All rights reserved. 88 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 27. Legal information 27.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 27.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 27.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. PCF8811 Product data sheet Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 89 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Quick reference data — The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. Bare die — All die are tested on compliance with their related technical specifications as stated in this data sheet up to the point of wafer sawing and are handled in accordance with the NXP Semiconductors storage and transportation conditions. If there are data sheet limits not guaranteed, these will be separately indicated in the data sheet. There are no post-packing tests performed on individual die or wafers. NXP Semiconductors has no control of third party procedures in the sawing, handling, packing or assembly of the die. Accordingly, NXP Semiconductors assumes no liability for device functionality or performance of the die or systems after third party sawing, handling, packing or assembly of the die. It is the responsibility of the customer to test and qualify their application in which the die is used. All die sales are conditioned upon and subject to the customer entering into a written die sale agreement with NXP Semiconductors through its legal department. 27.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus — logo is a trademark of NXP Semiconductors N.V. 28. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 90 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 29. Tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Table 28. Table 29. Table 30. Table 31. Table 32. Table 33. Table 34. Table 35. Table 36. Table 37. Table 38. Table 39. Table 40. Table 41. Table 42. Table 43. Table 44. Table 45. Ordering information . . . . . . . . . . . . . . . . . . . . .2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . .5 Bump and pad dimensions . . . . . . . . . . . . . . . .7 Alignment marker position[1] . . . . . . . . . . . . . . .7 Bump locations . . . . . . . . . . . . . . . . . . . . . . . . .7 Device recognition . . . . . . . . . . . . . . . . . . . . . .18 Command set selection . . . . . . . . . . . . . . . . . .18 Interface selection . . . . . . . . . . . . . . . . . . . . . .18 6800 series parallel interface functions . . . . . .28 I2C slave address byte . . . . . . . . . . . . . . . . . . .35 Co and D/C definitions . . . . . . . . . . . . . . . . . . .36 Instruction set[1] . . . . . . . . . . . . . . . . . . . . . . . .41 Common commands . . . . . . . . . . . . . . . . . . . .44 Power control register[1] . . . . . . . . . . . . . . . . . .44 Power-save mode (PSM), OS, DON, DAL and E combinations[1] . . . . . . . . . . . . . . . . . . .45 Read status byte . . . . . . . . . . . . . . . . . . . . . . .45 Multiplication settings . . . . . . . . . . . . . . . . . . .45 Specific basic commands . . . . . . . . . . . . . . . .45 Specific extended commands . . . . . . . . . . . . .45 Frame rate frequency . . . . . . . . . . . . . . . . . . .46 Temperature coefficient[1] . . . . . . . . . . . . . . . .46 Multiplication settings . . . . . . . . . . . . . . . . . . .46 RAM X/Y address range . . . . . . . . . . . . . . . . .49 Bias levels for MRA driving method . . . . . . . . .52 Relationship between multiplex rates and bias setting variables without icon row . . . . . .52 Relationship between multiplex rates and bias setting variables with the icon row (only extended command set) . . . . . . . . . . . . . . . . .53 Example values of VPR, VOP and VOFF for VLCD = 6 V . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Parameters of VLCD for the basic and extended command set . . . . . . . . . . . . . . . . . .55 ROM look-up table with values of VOFF, VPR, VOP and VLCD . . . . . . . . . . . . . . . . . . . . . .56 Limiting values[1] . . . . . . . . . . . . . . . . . . . . . . .63 Static characteristics . . . . . . . . . . . . . . . . . . . .64 Dynamic characteristics[1] . . . . . . . . . . . . . . . .66 Parallel interface (6800 series) timing characteristics . . . . . . . . . . . . . . . . . . . . . . . . .66 Serial interface timing characteristics[1] . . . . . .68 I2C-bus characteristics; F/S-mode . . . . . . . . . .71 I2C-bus characteristics; Hs-mode . . . . . . . . . .72 VOS/MMVOPCAL values in two’s complement notation . . . . . . . . . . . . . . . . . . . .76 Seal bit definition . . . . . . . . . . . . . . . . . . . . . . .77 Additional interface commands . . . . . . . . . . . .78 Sequence for filling the shift register; example 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Sequence for filling the shift register; example 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 Programming specification . . . . . . . . . . . . . . .81 Tray dimensions . . . . . . . . . . . . . . . . . . . . . . .84 Selection of LCD graphic drivers . . . . . . . . . . .85 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . .86 PCF8811 Product data sheet Table 46. Revision history . . . . . . . . . . . . . . . . . . . . . . . . 88 All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 91 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 30. Figures Fig 1. Fig 2. Fig 3. Fig 4. Fig 5. Fig 6. Fig 7. Fig 8. Fig 9. Fig 10. Fig 11. Fig 12. Fig 13. Fig 14. Fig 15. Fig 16. Fig 17. Fig 18. Fig 19. Fig 20. Fig 21. Fig 22. Fig 23. Fig 24. Fig 25. Fig 26. Fig 27. Fig 28. Fig 29. Fig 30. Fig 31. Fig 32. Fig 33. Fig 34. Fig 35. Fig 36. Fig 37. Block diagram of PCF8811 . . . . . . . . . . . . . . . . . .3 Pin configuration for PCF8811 . . . . . . . . . . . . . . . .4 Chip dimensions . . . . . . . . . . . . . . . . . . . . . . . . . .6 Alignment markers . . . . . . . . . . . . . . . . . . . . . . . . .7 DDRAM to display mapping. . . . . . . . . . . . . . . . .22 Sequence of writing data bytes into the RAM (basic command set) . . . . . . . . . . . . . . . . . . . . . .23 Sequence of writing data bytes into the RAM with horizontal addressing; V = 0 (extended command set) . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Sequence of writing data bytes into the RAM with vertical addressing; V = 1 (extended command set) . . . . . . . . . . . . . . . . . . . . . . . . . . .24 RAM byte organization, if DOR = 0 (extended command set) . . . . . . . . . . . . . . . . . . . . . . . . . . .25 RAM byte organization, if DOR = 1 (extended command set) . . . . . . . . . . . . . . . . . . . . . . . . . . .25 RAM format addressing; MX = 1 (both command sets) . . . . . . . . . . . . . . . . . . . . . . . . . .26 RAM format addressing; MX = 0 (both command sets) . . . . . . . . . . . . . . . . . . . . . . . . . .26 RAM format addressing; MY = 1 (both command sets) . . . . . . . . . . . . . . . . . . . . . . . . . .27 RAM format addressing; MY = 0 (both command sets) . . . . . . . . . . . . . . . . . . . . . . . . . .27 Serial bus protocol: transmission of 1 byte . . . . .29 Serial bus protocol: transmission of several bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Transmission of several bytes . . . . . . . . . . . . . . .29 Transmission interrupted by SCE . . . . . . . . . . . .30 Read mode SPI 3-line and 4-line . . . . . . . . . . . . .30 Serial data stream; write mode . . . . . . . . . . . . . .31 Write mode: a control bit followed by a transmission byte . . . . . . . . . . . . . . . . . . . . . . . . .32 Write mode: transmission of several bytes . . . . .32 Write mode: interrupted by reset (RES). . . . . . . .32 Read mode: serial interface 3-line . . . . . . . . . . . .33 System configuration . . . . . . . . . . . . . . . . . . . . . .34 Bit transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Definition of START and STOP conditions. . . . . .34 Acknowledge on the I2C-bus . . . . . . . . . . . . . . . .35 I2C-bus protocol . . . . . . . . . . . . . . . . . . . . . . . . . .36 Control byte format . . . . . . . . . . . . . . . . . . . . . . .36 Data transfer format in Hs-mode . . . . . . . . . . . . .37 Data transfer timing format in F/S-mode and Hs-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Master transmits in Hs-mode to slave receiver; write mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Master receives from slave transmitter (status register is read); read mode. . . . . . . . . . . . . . . . .39 Programming the L[6:0] address and C[6:0] address when MY = 0 . . . . . . . . . . . . . . . . . . . . .50 Bias levels for an MRA system with p = 8 and Gmax = F . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Setting of VOP in the basic and extended command set . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 PCF8811 Product data sheet Fig 38. Fig 39. Fig 40. Fig 41. Fig 42. Fig 43. Fig 44. Fig 45. Fig 46. Fig 47. Fig 48. Fig 49. Fig 50. Fig 51. Fig 52. Fig 53. Fig 54. Fig 55. Fig 56. Fig 57. VLCD programming of the PCF8811 . . . . . . . . . . 59 Temperature coefficients . . . . . . . . . . . . . . . . . . . 60 Device protection diagrams. . . . . . . . . . . . . . . . . 61 Parallel interface timing; 6800 series . . . . . . . . . 67 3-line serial interface timing . . . . . . . . . . . . . . . . 69 4-line serial interface timing . . . . . . . . . . . . . . . . 69 Serial interface timing; SPI 3-line or 4-line (read mode). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Serial interface timing; 3-line serial interface (read mode). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 I2C-bus timing diagram (F/S-mode) . . . . . . . . . . 71 I2C-bus timing diagram (Hs-mode) . . . . . . . . . . . 73 Reset timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Application diagram: internal charge pump and a single supply . . . . . . . . . . . . . . . . . . . . . . . 74 Application diagram: internal charge pump and two separate supplies (VDD1 and VDD2) . . . . 74 Application diagram: external high voltage . . . . . 75 VLCD calibration . . . . . . . . . . . . . . . . . . . . . . . . . . 76 Basic OTP architecture . . . . . . . . . . . . . . . . . . . . 78 Shift register contents after example sequence, see Table 40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Programming waveforms . . . . . . . . . . . . . . . . . . 82 Tray details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Tray alignment. . . . . . . . . . . . . . . . . . . . . . . . . . . 83 All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 92 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 31. Contents 1 2 3 4 5 6 6.1 6.2 6.2.1 6.2.2 7 7.1 7.1.1 7.1.2 7.1.3 7.1.4 7.1.5 7.1.6 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5 Tie-off pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Bare die information . . . . . . . . . . . . . . . . . . . . . 6 Functional description . . . . . . . . . . . . . . . . . . 17 Pin functions . . . . . . . . . . . . . . . . . . . . . . . . . . 17 R0 to R80: row driver outputs . . . . . . . . . . . . . 17 C0 to C127: column driver signals . . . . . . . . . 17 VSS1 and VSS2: negative power supply rails . . 17 VDD1 to VDD3: positive power supply rails . . . . 17 VOTPPROG: OTP power supply . . . . . . . . . . . . 17 VLCDOUT, VLCDIN, and VLCDSENSE: LCD power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 7.1.7 T1 to T5: test pins . . . . . . . . . . . . . . . . . . . . . . 17 7.1.8 MF2 to MF0 . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7.1.9 DS0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7.1.10 VOS4 to VOS0 . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7.1.11 EXT: extended command set . . . . . . . . . . . . . 18 7.1.12 PS0, PS1, and PS2 . . . . . . . . . . . . . . . . . . . . 18 7.1.13 D/C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7.1.14 R/W/WR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 7.1.15 E/RD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 7.1.16 SCLH/SCE . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 7.1.17 SDAH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 7.1.18 SDAHOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 7.1.19 DB7 to DB0. . . . . . . . . . . . . . . . . . . . . . . . . . . 19 7.1.19.1 DB7 to DB0 (parallel interface) . . . . . . . . . . . . 19 7.1.19.2 DB7, DB6 and DB5 (serial interface) . . . . . . . 19 7.1.19.3 DB3 and DB2 (I2C-bus interface) . . . . . . . . . . 20 7.1.20 OSC: oscillator . . . . . . . . . . . . . . . . . . . . . . . . 20 7.1.21 RES: reset . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 7.2 Block diagram functions . . . . . . . . . . . . . . . . . 20 7.2.1 Address counter . . . . . . . . . . . . . . . . . . . . . . . 20 7.2.2 Display data RAM . . . . . . . . . . . . . . . . . . . . . . 20 7.2.3 Timing generator. . . . . . . . . . . . . . . . . . . . . . . 20 7.2.4 Display address counter . . . . . . . . . . . . . . . . . 20 7.2.5 Display status . . . . . . . . . . . . . . . . . . . . . . . . . 21 7.2.6 LCD row and column drivers . . . . . . . . . . . . . 21 8 Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 8.1 Display data RAM structure . . . . . . . . . . . . . . 23 8.1.1 8.1.2 8.1.2.1 8.1.2.2 8.1.2.3 9 9.1 10 10.1 10.1.1 10.1.2 10.2 10.2.1 10.2.2 11 11.1 11.1.1 11.1.2 11.1.3 11.1.4 11.2 11.3 11.4 12 12.1 12.1.1 12.1.2 12.1.3 12.2 12.3 12.3.1 12.3.2 12.4 12.5 12.5.1 12.5.2 12.6 12.7 12.8 12.9 12.10 12.10.1 12.10.2 12.11 Basic command set . . . . . . . . . . . . . . . . . . . . Extended command set . . . . . . . . . . . . . . . . . Horizontal/vertical addressing . . . . . . . . . . . . Data order . . . . . . . . . . . . . . . . . . . . . . . . . . . Features available in both command sets . . . Parallel interface . . . . . . . . . . . . . . . . . . . . . . . 6800 series parallel interface . . . . . . . . . . . . . Serial interfacing (SPI and serial interface) . Serial peripheral interface lines . . . . . . . . . . . Write mode. . . . . . . . . . . . . . . . . . . . . . . . . . . Read mode (only extended command set) . . Serial interface (3-line). . . . . . . . . . . . . . . . . . Write mode. . . . . . . . . . . . . . . . . . . . . . . . . . . Read mode (only extended command set) . . I2C-bus interface . . . . . . . . . . . . . . . . . . . . . . . Characteristics of the I2C-bus . . . . . . . . . . . . System configuration . . . . . . . . . . . . . . . . . . . Bit transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . START and STOP conditions. . . . . . . . . . . . . Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . I2C-bus protocol . . . . . . . . . . . . . . . . . . . . . . . I2C-bus Hs-mode protocol . . . . . . . . . . . . . . . Command decoder . . . . . . . . . . . . . . . . . . . . Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . Instruction set commands . . . . . . . . . . . . . . . Common instructions of the basic and extended command set . . . . . . . . . . . . . . . . . Specific commands of the basic command set . . . . . . . . . . . . . . . . . . . . . . . . . Specific commands of the extended command set . . . . . . . . . . . . . . . . . . . . . . . . . Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . Reset function . . . . . . . . . . . . . . . . . . . . . . . . Basic command set . . . . . . . . . . . . . . . . . . . . Extended command set . . . . . . . . . . . . . . . . . Power-save mode . . . . . . . . . . . . . . . . . . . . . Display control . . . . . . . . . . . . . . . . . . . . . . . . Bit MX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bit MY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set Y address of RAM . . . . . . . . . . . . . . . . . . Set X address of RAM . . . . . . . . . . . . . . . . . . Set display start line . . . . . . . . . . . . . . . . . . . . Bias levels . . . . . . . . . . . . . . . . . . . . . . . . . . . Set VOP value. . . . . . . . . . . . . . . . . . . . . . . . . Basic command set . . . . . . . . . . . . . . . . . . . . Extended command set . . . . . . . . . . . . . . . . . Temperature control . . . . . . . . . . . . . . . . . . . . 23 23 23 25 25 28 28 28 28 28 30 30 31 32 33 33 33 34 34 35 35 37 40 40 44 44 45 45 47 47 47 47 48 48 48 49 49 49 49 51 53 54 59 60 continued >> PCF8811 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 6 — 10 February 2015 © NXP Semiconductors N.V. 2015. All rights reserved. 93 of 94 PCF8811 NXP Semiconductors 80 x 128 pixels matrix LCD driver 13 Internal circuitry. . . . . . . . . . . . . . . . . . . . . . . . 14 Safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 16 Static characteristics. . . . . . . . . . . . . . . . . . . . 17 Dynamic characteristics . . . . . . . . . . . . . . . . . 17.1 Parallel interface timing characteristics . . . . . 17.2 Serial interface timing characteristics . . . . . . . 17.3 I2C-bus interface timing characteristics . . . . . 18 Application information. . . . . . . . . . . . . . . . . . 19 Support information . . . . . . . . . . . . . . . . . . . . 19.1 Module maker programming. . . . . . . . . . . . . . 19.1.1 VLCD calibration . . . . . . . . . . . . . . . . . . . . . . . 19.1.2 Temperature coefficient selection . . . . . . . . . . 19.1.3 Seal bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.1.4 OTP architecture . . . . . . . . . . . . . . . . . . . . . . 19.1.5 Interface commands . . . . . . . . . . . . . . . . . . . . 19.1.5.1 CALMM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.1.5.2 Refresh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.1.6 Example sequence for filling the shift register 19.1.7 Programming flow. . . . . . . . . . . . . . . . . . . . . . 19.1.8 Programming specification . . . . . . . . . . . . . . . 20 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 21 Handling information. . . . . . . . . . . . . . . . . . . . 22 Packing information . . . . . . . . . . . . . . . . . . . . 23 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23.1 LCD graphic driver selection. . . . . . . . . . . . . . 24 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 25 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 27 Legal information. . . . . . . . . . . . . . . . . . . . . . . 27.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 27.2 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.3 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.4 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Contact information. . . . . . . . . . . . . . . . . . . . . 29 Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 62 63 64 66 66 68 71 74 75 75 75 76 77 77 78 78 79 79 80 81 82 82 83 85 85 86 87 88 89 89 89 89 90 90 91 92 93 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP Semiconductors N.V. 2015. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 10 February 2015 Document identifier: PCF8811