LCD-016N001A-NFG-ET www.vishay.com Vishay 16 x 1 Character LCD FEATURES • Type: Character • Display format: 16 x 1 characters • Built-in controller: ST 7066 or equivalent • Duty cycle: 1/16 • 5 x 8 dots includes cursor • + 5 V power supply • LED can be driven by pin 1, pin 2, pin 15, pin 16, or A and K • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 MECHANICAL DATA ITEM ABSOLUTE MAXIMUM RATINGS STANDARD VALUE Module Dimension UNIT 80.0 x 36.0 x 9.7 ITEM SYMBOL STANDARD VALUE MIN. TYP. MAX. Viewing Area 66.0 x 16.0 Power Supply VDD to VSS - 0.3 - 7.0 Dot Size 0.55 x 0.75 Input Voltage VI VSS - VDD Dot Pitch 0.63 x 0.83 Mounting Hole 75.0 x 31.0 Character Size 3.07 x 6.56 mm UNIT V Note • VSS = 0 V, VDD = 5.0 V ELECTRICAL CHARACTERSITICS ITEM SYMBOL CONDITION Input Voltage VDD Supply Current IDD Recommended LC Driving Voltage for Normal Temperature Version Module VDD to V0 STANDARD VALUE UNIT MIN. TYP. MAX. VDD = + 5 V 4.5 5.0 5.5 V VDD = + 5 V 1.0 1.2 1.5 mA 5.6 - 20 °C - - 0 °C - - - 25 °C - 4.5 - 50 °C - - - 70 °C 3.7 - - V LED Forward Voltage VF 25 °C - - - V LED Forward Current IF 25 °C - - - mA EL Power Supply Current IEL VEL = 110 VAC, 400 Hz - - - mA DISPLAY CHARACTER ADDRESS CODE Display Position DD RAM Address 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 00 01 02 03 04 05 06 07 40 41 42 43 44 45 46 47 Document Number: 37411 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay INTERFACE PIN FUNCTION PIN NO. SYMBOL FUNCTION 1 VSS Ground 2 VDD Supply voltage for logic (+ 5 V) 3 V0 Operating voltage for LCD (variable) 4 RS H/L; H: data/L: instruction code 5 R/W H/L; H: read (MPU → module)/L: write (MPU → module) 6 E H, H → L chip enable signal 7 DB0 H/L data bus line 8 DB1 H/L data bus line 9 DB2 H/L data bus line 10 DB3 H/L data bus line 11 DB4 H/L data bus line 12 DB5 H/L data bus line 13 DB6 H/L data bus line 14 DB7 H/L data bus line 15 A no connection 16 K no connection DIMENSIONS in millimeters 3.77 3.07 6.56 0.83 0.75 0.63 0.55 80.0 ± 0.5 4.4 71.2 7.0 66.0 (VA) 2.5 31.0 15.46 16 x Ø 1.0 11.46 38.1 (P2.54 x 15) 2.0 Dot Size 2.45 13.08 8.0 59.62 (AA) 2.0 14.72 10.0 5.4 10.19 9.7 Max. 5.1 16 1 6.56 (AA) A K A 5.08 25.2 16.0 (VA) 36.0 ± 0.5 K 4 x Ø 2.5 PTH 4 x Ø 5.0 PAD 2.5 75.0 1.6 4 x Ø 1.0 PTH EL or NO B/L Document Number: 37411 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay 1.Module Classification Information ġ ġ ġ ġ LCD -016 N 001 A -N F G -ET 1. Brand烉Vishay Intertechnology, Inc. 2. Horizontal Format: 16 characters 3. Display Type烉NɦCharacter Type, HɦGraphic Type 4. Vertical Format: 1 lines 5. Model serials no.: A 6. Backlight NɦWithout backlight TɦLED, White Type烉 BɦEL, Blue green AɦLED, Amber DɦEL, Green RɦLED, Red WɦEL, White OɦLED, Orange FɦCCFL, White GɦLED, Green YɦLED, Yellow Green 7. LCD Mode烉 BɦTN Positive, Gray TɦFSTN Negative NɦTN Negative, GɦSTN Positive, Gray YɦSTN Positive, Yellow Green MɦSTN Negative, Blue FɦFSTN Positive 8. LCD Polarizer AɦReflective, N.T, 6:00 HɦTransflective, W.T,6:00 Type/ Temperature DɦReflective, N.T, 12:00 KɦTransflective, W.T,12:00 range/ View GɦReflective, W. T, 6:00 CɦTransmissive, N.T,6:00 direction JɦReflective, W. T, 12:00 FɦTransmissive, N.T,12:00 BɦTransflective, N.T,6:00 IɦTransmissive, W. T, 6:00 EɦTransflective, N.T.12:00 LɦTransmissive, W.T,12:00 9. Special Code ET : English and European standard font Fits in with the ROHS Directions and regulations Document Number: 37411 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay 2.Precautions in use of LCD Modules (1)Avoid applying excessive shocks to the module or making any alterations or modifications to it. (2)Don’t make extra holes on the printed circuit board, modify its shape or change the components of LCD module. (3)Don’t disassemble the LCM. (4)Don’t operate it above the absolute maximum rating. (5)Don’t drop, bend or twist LCM. (6)Soldering: only to the I/O terminals. (7)Storage: please storage in anti-static electricity container and clean environment. (8)Supplier has the right to change the passive components (9)Supplier has the right to change the PCB Rev. 3.General Specification Item Dimension Unit Number of Characters 16 characters x 1 Lines 炼 Module dimension 80.0 x 36.0 x 9.7(MAX) mm View area 66.0 x 16.0 mm Active area 59.62 x 6.56 mm Dot size 0.55 x 0.75 mm Dot pitch 0.63 x 0.83 mm Character size 3.07 x 6.56 mm Character pitch 3.77 x 6.56 mm Duty FSTN Positive Reflective, (In LCD production, It will occur slightly color difference. We can only guarantee the same color in the same batch.) 1/16 View direction 6 o’clock LCD type Document Number: 37411 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay 4.Absolute Maximum Ratings Item Symbol Min Typ Max Unit Operating Temperature TOP -20 炼 +70 ɗ Storage Temperature TST -30 炼 +80 ɗ Input Voltage VI VSS 炼 VDD V Supply Voltage For Logic VDD-VSS -0.3 炼 7 V Supply Voltage For LCD VDD-V0 -0.3 炼 13 V 5.Electrical Characteristics Item Supply Voltage For Logic Symbol Condition Min Typ Max Unit VDD-VSS 炼 4.5 5.0 5.5 V Ta=-20ɗ 炼 炼 5.6 V Ta=25ɗ 炼 4.5 炼 V Ta=70ɗ 3.7 炼 炼 V Supply Voltage For LCD VDD-V0 *Note Input High Volt. VIH 炼 0.7 VDD 炼 VDD V Input Low Volt. VIL 炼 VSS 炼 0.6 V Output High Volt. VOH 炼 3.9 炼 炼 V Output Low Volt. VOL 炼 炼 炼 0.4 V Supply Current IDD VDD=5V 1.0 1.2 1.5 mA * Note: Please design the VOP adjustment circuit on customer's main board Vdd VR 10K~20K Vo LCM Module VSS Document Number: 37411 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay 6.Optical Characteristics Item Symbol Condition Min Typ Max Unit (V)ȧ CRʁ2 30 炼 60 deg (H)ȴ CRʁ2 -45 炼 45 deg CR 炼 5 炼 炼 T rise 炼 炼 150 200 ms T fall 炼 炼 150 200 ms View Angle Contrast Ratio Response Time @ 25C Definition of Operation Voltage (Vop) Intensity 100炴 Definition of Response Time ( Tr , Tf ) Non-selected Conition Selected Wave Non-selected Wave Selected Conition Non-selected Conition Intensity 10炴 Cr Max Cr = Lon / Loff 90炴 100炴 Vop Tr Driving Voltage(V) [positive type] Tf [positive type] Conditions : Operating Voltage : Vop Viewing Angle(ȧ炻ȴ) : 0Ʊ炻 0Ʊ Frame Frequency : 64 HZ Driving Waveform : 1/N duty , 1/a bias Definition of viewing angle(CRʁ ʁ2) ȧb ȧf ȧl ȴ= 180Ʊ ȧr ȴ= 90Ʊ ȴ= 270Ʊ ȴ= 0Ʊ Document Number: 37411 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay 7.Interface Pin Function Pin No. Symbol Level Description 1 VSS 0V Ground 2 VDD 5.0V 3 VO 4 RS H/L H: DATA, L: Instruction code 5 R/W H/L H: Read(MPUɦModule) L: Write(MPUɦModule) 6 E H,HɦL 7 DB0 H/L Data bus line 8 DB1 H/L Data bus line 9 DB2 H/L Data bus line 10 DB3 H/L Data bus line 11 DB4 H/L Data bus line 12 DB5 H/L Data bus line 13 DB6 H/L Data bus line 14 DB7 H/L Data bus line 15 A 炼 NC 16 K 炼 NC Supply Voltage for logic (Variable) Operating voltage for LCD Chip enable signal Document Number: 37411 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay 8.Contour Drawing &Block Diagram 80 series or 68 series VR 10K~20K Vdd Vo Vss Com1~8 Controller/Com Driver HD44780 or Equivalent Bias and Power Circuit MPU RS R/W E DB0~DB7 Com9~16 16X1 LCD Seg1~40 External contrast adjustment. Character located 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 DDRAM address 00 01 02 03 04 05 06 07 40 41 42 43 44 45 46 47 2-line display mode. Document Number: 37411 8 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay 9.Function Description The LCD display Module is built in a LSI controller, the controller has two 8-bit registers, an instruction register (IR) and a data register (DR). The IR stores instruction codes, such as display clear and cursor shift, and address information for display data RAM (DDRAM) and character generator (CGRAM). The IR can only be written from the MPU. The DR temporarily stores data to be written or read from DDRAM or CGRAM. When address information is written into the IR, then data is stored into the DR from DDRAM or CGRAM. By the register selector (RS) signal, these two registers can be selected. RS R/W Operation 0 0 IR write as an internal operation (display clear, etc.) 0 1 Read busy flag (DB7) and address counter (DB0 to DB7) 1 0 Write data to DDRAM or CGRAM (DR to DDRAM or CGRAM) 1 1 Read data from DDRAM or CGRAM (DDRAM or CGRAM to DR) Busy Flag (BF) When the busy flag is 1, the controller LSI is in the internal operation mode, and the next instruction will not be accepted. When RS=0 and R/W=1, the busy flag is output to DB7. The next instruction must be written after ensuring that the busy flag is 0. Address Counter (AC) The address counter (AC) assigns addresses to both DDRAM and CGRAM Display Data RAM (DDRAM) This DDRAM is used to store the display data represented in 8-bit character codes. Its extended capacity is 80ǘ8 bits or 80 characters. Below figure is the relationship between DDRAM addresses and positions on the liquid crystal display. High bits Low bits Example: DDRAM addresses 4E AC (hexadecimal) AC6 AC5 AC4 AC3 AC2 AC1 AC0 1 0 0 1 1 1 0 Document Number: 37411 9 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay Display position DDRAM address 1 00 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 01 02 03 04 05 06 07 40 41 42 2-Line display mode 43 44 45 46 47 Character Generator ROM (CGROM) The CGROM generate 5ǘ8 dot or 5ǘ10 dot character patterns from 8-bit character codes. See Table 2. Character Generator RAM (CGRAM) In CGRAM, the user can rewrite character by program. For 5ǘ8 dots, eight character patterns can be written, and for 5ǘ10 dots, four character patterns can be written. Write into DDRAM the character code at the addresses shown as the left column of table 1. To show the character patterns stored in CGRAM. Document Number: 37411 10 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay Relationship between CGRAM Addresses, Character Codes (DDRAM) and Character patterns Table 1. For 5 * 8 dot character patterns Character Codes ( DDRAM data ) 7 6 5 4 3 2 1 0 High Low 0 0 0 0 * 0 0 0 0 0 0 0 * 0 0 1 0 0 0 0 * 1 1 1 CGRAM Address 5 4 3 2 1 0 Low 0 0 0 0 0 1 0 1 0 0 0 1 0 1 0 1 1 1 1 0 0 0 0 0 1 0 1 0 0 1 1 0 1 0 1 1 1 1 0 0 0 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 0 1 0 1 Character Patterns ( CGRAM data ) 7 6 5 4 3 2 1 0 High 0 0 1 1 * * * * * * * * * * * * * * * * * High * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Low 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Character pattern( 1 ) 0 0 0 0 Character pattern( 2 ) 0 0 0 0 0 0 0 0 0 0 0 0 0 Cursor pattern Cursor pattern * * * For 5 * 10 dot character patterns Character Codes ( DDRAM data ) 7 6 5 4 3 2 1 0 High Low 0 0 0 0 * 0 0 0 CGRAM Address 5 4 3 2 1 0 High Character Patterns ( CGRAM data ) 7 6 5 4 3 2 1 0 Low 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 1 High 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 * * * * * * * * * * * * * * * * * * * * * * Low * 0 0 0 0 0 * 0 0 0 0 0 0 0 * 0 0 * 0 0 0 * 0 0 0 * 0 * 0 0 0 0 * 0 0 0 0 * 0 0 0 0 * * 0 0 0 0 0 Character pattern Cursor pattern * * * * * * * * : " High " Document Number: 37411 11 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay 10.Character Generator ROM Pattern Table.2 Upper 4 bit Lower 4 bit LLLL LLLH LLHL LLHH LHLL LHLH LHHL LHHH HLLL HLLH HLHL HLHH HHLL HHLH HHHL HHHH LLLL CG RAM (1) LLLH CG RAM (2) LLHL CG RAM (3) LLHH CG RAM (4) LHLL CG RAM (5) LHLH CG RAM (6) LHHL CG RAM (7) LHHH CG RAM (8) HLLL CG RAM (1) HLLH CG RAM (2) HLHL CG RAM (3) HLHH CG RAM (4) HHLL CG RAM (5) HHLH CG RAM (6) HHHL CG RAM (7) HHHH CG RAM (8) Document Number: 37411 12 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay 11.Instruction Table Instruction Code Instruction Execution time (fosc=270Khz) Description RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Clear Display 0 0 0 0 0 0 0 0 0 1 Write “00H” to DDRAM and set DDRAM address to “00H” from AC 1.53ms 1.53ms Return Home 0 0 0 0 0 0 0 0 1 炼 Set DDRAM address to “00H” from AC and return cursor to its original position if shifted. The contents of DDRAM are not changed. Entry Mode Set 0 0 0 0 0 0 0 1 I/D SH Assign cursor moving direction and enable the shift of entire display. 39ȫs Display ON/OFF Control 0 0 0 0 0 0 1 D C B Set display (D), cursor (C), and blinking of cursor (B) on/off control bit. 39ȫs Cursor or Display Shift 0 0 0 0 0 1 炼 炼 control bit, and the direction, without Function Set Set CGRAM Address Set DDRAM Address Set cursor moving and display shift S/C R/L 39ȫs changing of DDRAM data. Set interface data length (DL:8-bit/4-bit), numbers of display line (N:2-line/1-line)and, display font type (F:5ǘ11 dots/5ǘ8 dots) 39ȫs AC5 AC4 AC3 AC2 AC1 AC0 Set CGRAM address in address counter. 39ȫs 1 DL N F 炼 炼 0 0 0 0 0 0 0 1 0 0 1 AC6 AC5 AC4 AC3 AC2 AC1 AC0 Set DDRAM address in address counter. 39ȫs Whether during internal operation or not can be known by reading BF. The AC6 AC5 AC4 AC3 AC2 AC1 AC0 contents of address counter can also be read. 0ȫs Read Busy Flag and Address 0 1 BF Write Data to RAM 1 0 D7 D6 D5 D4 D3 D2 D1 D0 Write data into internal RAM (DDRAM/CGRAM). 43ȫs Read Data from RAM 1 1 D7 D6 D5 D4 D3 D2 D1 D0 Read data from internal RAM (DDRAM/CGRAM). 43ȫs 点 ”炼”烉don’t care Document Number: 37411 13 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay 12.Timing Characteristics 12.1ġġ Write Operation Ta=25ɗ, VDD=5įıV Item Symbol Min Typ Max Unit Enable cycle time TC 1200 炼 炼 ns Enable pulse width TPW 140 炼 炼 ns Enable rise/fall time TR,TF 炼 炼 25 ns Address set-up time (RS, R/W to E) tAS 0 炼 炼 ns Address hold time tAH 10 炼 炼 ns Data set-up time tDSW 40 炼 炼 ns tH 10 炼 炼 ns Data hold time Document Number: 37411 14 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay 12.2ġġ Read Operation Ta=25ɗ, VDD=5ŗ Item Symbol Min Typ Max Unit TC 1200 炼 炼 ns TPW 140 炼 炼 ns TR,TF 炼 炼 25 ns Address set-up time (RS, R/W to E) tAS 0 炼 炼 ns Address hold time tAH 10 炼 炼 ns Data delay time tDDR 炼 炼 100 ns Data hold time tH 10 炼 炼 ns Enable cycle time Enable pulse width (high level) Enable rise/fall time Document Number: 37411 15 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay 13.Initializing of LCM Power on Wait for more than 40 ms after VDD rises to 4.5 V BF can not be checked before this instruction. RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 * 0 * * * 0 0 1 1 0 Function set Wait for more than 39us BF can not be checked before this instruction. RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 0 0 0 1 0 * * * * 0 0 N F * * * * * * 0 Function set Wait for more than 39 µs BF can not be checked before this instruction. RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 0 0 0 1 0 * * * * Function set 0 * * * N F * 0 0 * * Wait for more than 37us RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Display ON/OFF control * * * 0 0 * 0 0 0 0 * * * 0 B * 1 D C 0 Wait for more than 37 µs RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Display Clear * * 0 0 * 0 * 0 0 0 * * 0 0 * * 0 0 0 1 Wait for more than 1.53ms RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Entry Mode Set * * 0 0 0 * 0 0 0 * 0 1 * * * 0 0 I/D SH * Initialization ends 4-Bit Ineterface Document Number: 37411 16 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay Power on Wait for more than 40 ms after VDD rises to 4.5 V BF can not be checked before this instruction. RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Function set 0 0 0 0 1 1 N F * * Wait for more than 39us BF can not be checked before this instruction. RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 0 0 0 0 1 1 N F * * Function set Wait for more than 37us RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Display ON/OFF control 0 0 0 0 0 0 1 B C D Wait for more than 37 µs RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Display Clear 0 0 0 0 0 0 0 0 0 1 Wait for more than 1.53ms RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Entry Mode Set 0 0 0 0 0 0 0 1 I/D S Initialization ends 8-Bit Ineterface Document Number: 37411 17 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay 14.Reliability Content of Reliability Test (wide temperature, -20ɗ~70ɗ) Environmental Test Test Item High Temperature storage Low Temperature storage High Temperature Operation Low Temperature Operation High Temperature/ Humidity Operation Thermal shock resistance Content of Test Test Condition Endurance test applying the high storage temperature 80ɗ for a long time. 200hrs Endurance test applying the high storage temperature -30ɗ for a long time. 200hrs Endurance test applying the electric stress (Voltage & 70ɗ Current) and the thermal stress to the element for a 200hrs long time. Endurance test applying the electric stress under low -20ɗ temperature for a long time. 200hrs The module should be allowed to stand at 60 ɗ,90%RH max 60ɗ,90%RH For 96hrs under no-load condition excluding the 96hrs polarizer, Then taking it out and drying it at normal temperature. The sample should be allowed stand the following 10 cycles of operation -20ɗ/70ɗ -20ɗ 25ɗ 70ɗ 10 cycles 30min 1 cycle 5min Note 2 1,2 —— 1 1,2 —— 30min Vibration test Endurance test applying the vibration during transportation and using. Total fixed amplitude : 1.5mm Vibration Frequency : 10~55Hz 3 One cycle 60 seconds to 3 directions of X,Y,Z for Each 15 minutes Static electricity test Endurance test applying the electric stress to the terminal. VS=800V,RS=1.5kȟ —— CS=100pF 1 time Note1: No dew condensation to be observed. Note2: The function test shall be conducted after 4 hours storage at the normal Temperature and humidity after remove from the test chamber. Note3: Vibration test will be conducted to the product itself without putting it in a container. Document Number: 37411 18 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay 15. Inspection specification NO 01 02 Item Criterion AQL Electrical Testing 1.1 Missing vertical, horizontal segment, segment contrast defect. 1.2 Missing character , dot or icon. 1.3 Display malfunction. 1.4 No function or no display. 1.5 Current consumption exceeds product specifications. 1.6 LCD viewing angle defect. 1.7 Mixed product types. 1.8 Contrast defect. 0.65 Black or white 2.1 White and black spots on display ʀ0.25mm, no more than spots on LCD three white or black spots present. (display only) 2.2 Densely spaced: No more than two spots or lines within 3mm 3.1 Round type : As following drawing ȜľĩġŹġĬġźġĪġİġijġ ġ ġ ġ ŔŊśņġ 2.5 łŤŤŦűŵŢţŭŦġŒġŕŚġ ġ ġ ġ ġ ġ ȜʀıįIJıġ łŤŤŦűŵġůŰġťŦůŴŦġ ıįIJı烋Ȝʀıįijıġ 03 ıįijı烋ȜʀıįijĶġ IJġ LCD black ġ ıįijĶ烋Ȝġ ıġ spots, white spots, contamination (non-display) 3.2 Line type : (As following drawing) Length Width Acceptable Q TY --Wʀıįıij Accept no dense LʀĴįı 0.02烋WʀıįıĴ 2 LʀijįĶ 0.03烋WʀıįıĶġ --- 04 ijġ Polarizer bubbles If bubbles are visible, judge using black spot specifications, not easy to find, must check in specify direction. 0.05烋W Size Ȝ Ȝʀıįijı 2.5 2.5 As round type Acceptable Q TY Accept no dense ıįijı烋ȜʀıįĶı 3 ıįĶı烋ȜʀIJįıı 2 IJįıı烋Ȝ Total Q TY 0 2.5 3 Document Number: 37411 19 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com NO Item 05 Scratches Vishay Criterion AQL Follow NO.3 LCD black spots, white spots, contamination Symbols Define: x: Chip length y: Chip width z: Chip thickness k: Seal width t: Glass thickness a: LCD side length L: Electrode pad length: 6.1 General glass chip : 6.1.1 Chip on panel surface and crack between panels: 06 Chipped glass ŻĻġńũŪűġŵũŪŤŬůŦŴŴġ źĻġńũŪűġŸŪťŵũġ ŹĻġńũŪűġŭŦůŨŵũġ śʀIJİijŵġ ŏŰŵġŰŷŦųġŷŪŦŸŪůŨġŢųŦŢġ ŹʀIJİĹŢġ IJİijŵ烋Żʀijŵġ ŏŰŵġŦŹŤŦŦťġIJİĴŬġ ġ ŹʀIJİĹŢġ 2.5 ˞ŊŧġŵũŦųŦġŢųŦġijġŰųġŮŰųŦġŤũŪűŴĭġŹġŪŴġŵŰŵŢŭġŭŦůŨŵũġŰŧġŦŢŤũġŤũŪűįġ ġ ķįIJįijġńŰųůŦųġŤųŢŤŬĻġ ġ ŻĻġńũŪűġŵũŪŤŬůŦŴŴġ ġ źĻġńũŪűġŸŪťŵũġ śʀIJİijŵġ ŏŰŵġŰŷŦųġŷŪŦŸŪůŨġŢųŦŢġ ŹʀIJİĹŢġ IJİijŵ烋Żʀijŵġ ŏŰŵġŦŹŤŦŦťġIJİĴŬġ ġ ŹʀIJİĹŢġ ŹĻġńũŪűġŭŦůŨŵũġ ˞ŊŧġŵũŦųŦġŢųŦġijġŰųġŮŰųŦġŤũŪűŴĭġŹġŪŴġŵũŦġŵŰŵŢŭġŭŦůŨŵũġŰŧġŦŢŤũġŤũŪűįġ ġ Document Number: 37411 20 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com NO Vishay Item Criterion AQL ŔźŮţŰŭŴġĻġ x: Chip length y: Chip width z: Chip thickness k: Seal width t: Glass thickness a: LCD side length L: Electrode pad length 6.2 Protrusion over terminal : 6.2.1 Chip on electrode pad : źĻġńũŪűġŸŪťŵũġ ġ ŹĻġńũŪűġŭŦůŨŵũġ ŻĻġńũŪűġŵũŪŤŬůŦŴŴġ źʀıįĶŮŮġ ŹʀIJİĹŢġ ıġ 烋ġ Żġʀġŵġ ķįijįijġŏŰůĮŤŰůťŶŤŵŪŷŦġűŰųŵŪŰůĻġ 06 Glass crack 2.5 źĻġńũŪűġŸŪťŵũġ ġ ŹĻġńũŪűġŭŦůŨŵũġ ŻĻġńũŪűġŵũŪŤŬůŦŴŴġ źʀġōġ ŹʀIJİĹŢġ ıġ 烋ġ Żġʀġŵġ ġ ˞ŊŧġŵũŦġŤũŪűűŦťġŢųŦŢġŵŰŶŤũŦŴġŵũŦġŊŕŐġŵŦųŮŪůŢŭĭġŰŷŦųġijİĴġŰŧġŵũŦġŊŕŐġŮŶŴŵġ ųŦŮŢŪůġŢůťġţŦġŪůŴűŦŤŵŦťġŢŤŤŰųťŪůŨġŵŰġŦŭŦŤŵųŰťŦġŵŦųŮŪůŢŭġŴűŦŤŪŧŪŤŢŵŪŰůŴįġ ˞ŊŧġŵũŦġűųŰťŶŤŵġŸŪŭŭġţŦġũŦŢŵġŴŦŢŭŦťġţźġŵũŦġŤŶŴŵŰŮŦųĭġŵũŦġŢŭŪŨůŮŦůŵġŮŢųŬġ ůŰŵġţŦġťŢŮŢŨŦťįġ ķįijįĴġŔŶţŴŵųŢŵŦġűųŰŵŶţŦųŢůŤŦġŢůťġŪůŵŦųůŢŭġŤųŢŤŬįġ ġ źĻġŸŪťŵũġ ġ ŹĻġŭŦůŨŵũġ źʀIJİĴōġ ŹġʀġŢġ ġ Document Number: 37411 21 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com NO Item 07 Cracked glass 08 09 10 Backlight elements Bezel PCBˣCOB Vishay Criterion ŕũŦġōńŅġŸŪŵũġŦŹŵŦůŴŪŷŦġŤųŢŤŬġŪŴġůŰŵġŢŤŤŦűŵŢţŭŦįġ ġ ĹįIJġŊŭŭŶŮŪůŢŵŪŰůġŴŰŶųŤŦġŧŭŪŤŬŦųŴġŸũŦůġŭŪŵįġ ĹįijġŔűŰŵŴġŰųġŴŤųŢŵŤũŦťġŵũŢŵġŢűűŦŢųġŸũŦůġŭŪŵġŮŶŴŵġţŦġūŶťŨŦťįġŖŴŪůŨġ ōńŅġŴűŰŵĭġŭŪůŦŴġŢůťġŤŰůŵŢŮŪůŢŵŪŰůġŴŵŢůťŢųťŴįġ ĹįĴġŃŢŤŬŭŪŨũŵġťŰŦŴůȽŵġŭŪŨũŵġŰųġŤŰŭŰųġŸųŰůŨįġ ġ ġ ĺįIJġŃŦŻŦŭġŮŢźġůŰŵġũŢŷŦġųŶŴŵĭġţŦġťŦŧŰųŮŦťġŰųġũŢŷŦġŧŪůŨŦųűųŪůŵŴĭġŴŵŢŪůŴġ ŰųġŰŵũŦųġŤŰůŵŢŮŪůŢŵŪŰůįġ ĺįijġŃŦŻŦŭġŮŶŴŵġŤŰŮűŭźġŸŪŵũġūŰţġŴűŦŤŪŧŪŤŢŵŪŰůŴįġ ġ ġ IJıįIJġńŐŃġŴŦŢŭġŮŢźġůŰŵġũŢŷŦġűŪůũŰŭŦŴġŭŢųŨŦųġŵũŢůġıįijŮŮġŰųġ ŤŰůŵŢŮŪůŢŵŪŰůįġ IJıįijġńŐŃġŴŦŢŭġŴŶųŧŢŤŦġŮŢźġůŰŵġũŢŷŦġűŪůũŰŭŦŴġŵũųŰŶŨũġŵŰġŵũŦġŊńįġ IJıįĴġThe height of the COB should not exceed the height indicated in the assembly diagram. 10.4 There may not be more than 2mm of sealant outside the seal area on the PCB. And there should be no more than three places. 10.5 No oxidation or contamination PCB terminals. 10.6 Parts on PCB must be the same as on the production characteristic chart. There should be no wrong parts, missing parts or excess parts. 10.7 The jumper on the PCB should conform to the product characteristic chart. 10.8 If solder gets on bezel tab pads, LED pad, zebra pad or screw hold pad, make sure it is smoothed down. IJıįĺ The Scraping testing standard for Copper Coating of PCB AQL 2.5 0.65 2.5 0.65 2.5 0.65 2.5 2.5 0.65 2.5 2.5 0.65 0.65 2.5 2.5 X Y 11 Soldering X * Y<=2mm2ġ ġ IJIJįIJġŏŰġŶůĮŮŦŭŵŦťġŴŰŭťŦųġűŢŴŵŦġŮŢźġţŦġűųŦŴŦůŵġŰůġŵũŦġőńŃįġ IJIJįijġŏŰġŤŰŭťġŴŰŭťŦųġūŰŪůŵŴĭġŮŪŴŴŪůŨġŴŰŭťŦųġŤŰůůŦŤŵŪŰůŴĭġŰŹŪťŢŵŪŰůġŰųġ ŪŤŪŤŭŦįġ IJIJįĴġŏŰġųŦŴŪťŶŦġŰųġŴŰŭťŦųġţŢŭŭŴġŰůġőńŃįġ IJIJįĵġŏŰġŴũŰųŵġŤŪųŤŶŪŵŴġŪůġŤŰŮűŰůŦůŵŴġŰůġőńŃįġ ġ 2.5 2.5 2.5 0.65 Document Number: 37411 22 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com NO 12 Item General appearance Criterion ġ IJijįIJġŏŰġŰŹŪťŢŵŪŰůĭġŤŰůŵŢŮŪůŢŵŪŰůĭġŤŶųŷŦŴġŰųĭġţŦůťŴġŰůġŪůŵŦųŧŢŤŦġőŪůġ ĩŐōŃĪġŰŧġŕńőįġ IJijįijġŏŰġŤųŢŤŬŴġŰůġŪůŵŦųŧŢŤŦġűŪůġĩŐōŃĪġŰŧġŕńőįġ IJijįĴġŏŰġŤŰůŵŢŮŪůŢŵŪŰůĭġŴŰŭťŦųġųŦŴŪťŶŦġŰųġŴŰŭťŦųġţŢŭŭŴġŰůġűųŰťŶŤŵįġ IJijįĵġŕũŦġŊńġŰůġŵũŦġŕńőġŮŢźġůŰŵġţŦġťŢŮŢŨŦťĭġŤŪųŤŶŪŵŴįġ IJijįĶġŕũŦġŶűűŦųŮŰŴŵġŦťŨŦġŰŧġŵũŦġűųŰŵŦŤŵŪŷŦġŴŵųŪűġŰůġŵũŦġŪůŵŦųŧŢŤŦġűŪůġ ŮŶŴŵġţŦġűųŦŴŦůŵġŰųġŭŰŰŬġŢŴġŪŧġŪŵġŤŢŶŴŦŴġŵũŦġŪůŵŦųŧŢŤŦġűŪůġŵŰġŴŦŷŦųįġ IJijįķġŕũŦġųŦŴŪťŶŢŭġųŰŴŪůġŰųġŵŪůġŰŪŭġŰŧġŴŰŭťŦųŪůŨġĩŤŰŮűŰůŦůŵġŰųġŤũŪűġ ŤŰŮűŰůŦůŵĪġŪŴġůŰŵġţŶųůŦťġŪůŵŰġţųŰŸůġŰųġţŭŢŤŬġŤŰŭŰųįġ IJijįĸġŔŦŢŭŢůŵġŰůġŵŰűġŰŧġŵũŦġŊŕŐġŤŪųŤŶŪŵġũŢŴġůŰŵġũŢųťŦůŦťįġ IJijįĹġőŪůġŵźűŦġŮŶŴŵġŮŢŵŤũġŵźűŦġŪůġŴűŦŤŪŧŪŤŢŵŪŰůġŴũŦŦŵįġ IJijįĺġōńŅġűŪůġŭŰŰŴŦġŰųġŮŪŴŴŪůŨġűŪůŴįġ IJijįIJıġőųŰťŶŤŵġűŢŤŬŢŨŪůŨġŮŶŴŵġŵũŦġŴŢŮŦġŢŴġŴűŦŤŪŧŪŦťġŰůġűŢŤŬŢŨŪůŨġ ŴűŦŤŪŧŪŤŢŵŪŰůġŴũŦŦŵįġ IJijįIJIJġőųŰťŶŤŵġťŪŮŦůŴŪŰůġŢůťġŴŵųŶŤŵŶųŦġŮŶŴŵġŤŰůŧŰųŮġŵŰġűųŰťŶŤŵġ ŴűŦŤŪŧŪŤŢŵŪŰůġŴũŦŦŵįġ ġ Vishay AQL 2.5 0.65 2.5 2.5 2.5 2.5 2.5 0.65 0.65 0.65 0.65 Document Number: 37411 23 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 LCD-016N001A-NFG-ET www.vishay.com Vishay 16. Material List of Components for RoHS 1. Declaration that all of or part of products (with the mark “N” in code), including, but not limited to, the LCM, accessories or packages, manufactured and/or delivered to your company (including your subsidiaries and affiliated company) directly or indirectly by our company (including our subsidiaries or affiliated companies) do not intentionally contain any of the substances listed in all applicable EU directives and regulations, including the following substances. Exhibit A烉The Harmful Material List . Material (Cd) (Pb) (Hg) (Cr6+) PBBs PBDEs Limited Value 100 ppm 1000 ppm 1000 ppm 1000 ppm 1000 ppm 1000 ppm Above limited value is set up according to RoHS. 2.Process for RoHS requirement烉 (1) Use the Sn/Ag/Cu soldering surface烊the surface of Pb-free solder is rougher than we used before. (2) Heat-resistance temp.烉 Reflow烉250C,30 seconds Max.烊 Connector soldering wave or hand soldering烉320C, 10 seconds max. (3) Temp. curve of reflow, max. Temp.烉235C±5 degrees烊 Recommended customer’s soldering temp. of connector烉280C, 3 seconds. Document Number: 37411 24 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 08-Jan-13 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000