TCTR www.vishay.com Vishay Electro-Films Thin Film Center-Tapped Resistors Divider Network for High Temperature Applications FEATURES Product may not be to scale The TCTR series of center-tapped resistor dividers offer a small size, wide ohmic value range and excellent power capacity, maintaining these qualities to temperatures up to 250 °C. The TCTR Tantalum Nitride resistor material offers excellent resistance to high moisture environments. The TCTR’s six bonding pad configuration allows for maximum layout flexibility. The TCTRs are manufactured using Vishay Electro-Films (EFI) sophisticated thin-film equipment and manufacturing technology. The TCTR’s are 100 % electrically tested and visually inspected to MIL-STD-883. • Qualified to operate at elevated temperatures up to 250 °C • DC power rating up to 250 mW • Small size: 0.03" square • Case: 0303 • Self passivating tantalum nitride film • Oxidized silicon substrate • Wide value range: 100 to 100 k • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS Vishay EFI TCTR top-contact 0.03" square resistor divider chips are designed to operate at elevated temperatures and power loads in many types of hybrid (chip and wire) assemblies. They are ideally suited for extreme environment applications such as “down hole” drilling. TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES, AND TOLERANCES PARAMETER VALUE Resistance Range Tolerances TCR Tightest Standard Tolerance Available UNIT 100 to 100K ± 0.1 % Down to ± 25 ppm/°C Load Life Stability, 1000 h, +125 °C, 175 mW ± 0.1 % ±1% ± 25 ppm/°C ±2% ±2% ± 50 ppm/°C ± 100 ppm/°C 100 Ω 100 kΩ 100 Ω 1 kΩ 10 kΩ 100 kΩ STANDARD ELECTRICAL SPECIFICATIONS PARAMETER Noise, MIL-STD-202, Method 308 Moisture Resistance, MIL-STD-202, Method 106 VALUE UNIT -20 dB ± 0.5 max. R/R % Stability, 1000 h, +125 °C, 175 mW Down to ± 1 % Operating Temperature Range -55 to +250 °C ± 0.25 max. R/R % Down to ± 1 % Thermal Shock, MIL-STD-202, Method 107, Test Condition F High Temperature Exposure, +250 °C, 1000 h Dielectric Voltage Breakdown Operating Voltage DC Power Rating at +125 °C (Derated to Zero at +250 °C) 5 x Rated Power Short-Time Overload, +25 °C, 5 s TCR Tracking Between Halves (RA/RB) Center Tap Ratio (RA/RB) Tolerance Revision: 11-Sep-13 200 V 100 max. V 250 at 70 °C mW ± 0.25 max. R/R % ±2 ppm/°C 1 ± 1 standard % Document Number: 61095 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TCTR www.vishay.com Vishay Electro-Films DIMENSIONS TYPICAL RANGE 100 Ω to 1 MΩ SCHEMATIC R T = RA + R B RA RB MECHANICAL SPECIFICATIONS in inches (millimeters) PARAMETER Chip Size 0.030 x 0.030 ± 0.002 (0.762 x 0.762 ± 0.05) Chip Thickness 0.010 ± 0.002 (0.254 ± 0.05) Chip Substrate Material Oxidized silicon, 10 kÅ minimum SiO2 Film Material Tantalum nitride, self-passivating Passivation None Bonding Pad Size 0.005 x 0.005 (0.127 x 0.127) Number of Pads 6 Pad Material 100 μ" Au Backing None, lapped silicon (Au optional) GLOBAL PART NUMBER INFORMATION Global Part Number: TCTR50000FKGNHWS Global Part Number Description: TCTR 5K 1 % 100 ppm/°C Au None H WS T C T MODEL RESISTANCE TCTR First 4 digits are significant figures of resistance Revision: 11-Sep-13 R 5 0 0 RESISTANCE MULTILPLIER CODE TOL. CODE (%) C = 0.001 B = 0.01 A = 0.1 0=1 1 = 10 2 = 100 3 = 1000 B = 0.1 C = 0.25 D = 0.5 F = 1.0 G = 2.0 H = 2.5 J = 5.0 K = 10.0 0 0 TCR (ppm/°C) E = ± 25 C = ± 50 K = ± 100 M = ± 250 F K TERMINATION G = Au G N H W S BACK METAL VISUAL CLASS PACKAGING CODE G = Au N = None H= Class H K= Class K WS = Waffle pack 100 min., 1 mult Document Number: 61095 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000