Si82xx-EVB UG Si82 XX E VALUATION B OARD U SER ’ S G UIDE 1. Introduction The Si823x isolated driver family combines two independent isolated drivers into a single package. The Si8230/1/ 3/4 are high-side/low-side drivers, and the Si8232/5/6 are dual drivers. Versions with peak output currents of 0.5 A (Si8230/1/2) and 4.0 A (Si8233/4/5/6) are available. The Si8220/21 is a high-performance functional upgrade for opto-coupled drivers, such as the HCPL-3120 and the HPCL-0302 providing 2.5 A of peak output current. These ISOdrivers utilize Silicon Laboratories' proprietary silicon isolation technology, which provides a choice of 2.5, 3.75, or 5.0 kVrms withstand voltages. All drivers operate with a maximum output supply voltage of 24 V. High integration, low propagation delay, small installed size, flexibility, and cost-effectiveness make the family ideal for a wide range of isolated MOSFET/IGBT gate drive applications. The Si82xx evaluation board allows designers to evaluate Silicon Lab's family of ISOdrivers. The boards come populated with 5 kVrms versions of the Si8220, Si8233, Si8234, and Si8235. The board includes land pads for common surface mount and through-hole packaged FET/IGBT power transistors. The board also includes patch area for additional prototyping that can be used to accommodate any load configuration a designer might need to evaluate. For more ISOdriver information, visit Silicon Labs web site at www.silabs.com/isolation. The product data sheet and numerous application notes can be referenced to help facilitate designs. Rev. 0.1 6/11 Copyright © 2011 by Silicon Laboratories Si82xx-EVB UG Si82xx-EVB UG 2. Kit Contents The Si82xx Evaluation Kit contains the following items: Si82xx-based evaluation board (Si82xx-EVB) shown in Figure 1. Si8220, Opto-input, 2.5 A, 5 kV ISOdriver Si8233, 2-input, 4 A, 5 kV, High-Side/Low-Side ISOdriver Si8234, PWM-input, 4 A, 5 kV High-Side/Low-Side ISOdriver Si8235, 2-input, 4 A, 5 kV Dual ISOdriver Figure 1. Si82xx Evaluation Board Overview 2 Rev. 0.1 Si8 2 x x -E VB U G 3. Si82xx ISOdriver Board Overview The Si82xx evaluation board is populated with the following ISOdrivers: Si8220 in wide-body SOIC-16 package, opto-input, 2.5 A, 5 kV ISOdriver Si8233 in wide-body SOIC-16 package, 2-input, 4 A, 5 kV High-Side/Low-Side ISOdriver Si8234 in wide-body SOIC-16 package, PWM-input, 4 A, 5 kV High-Side/Low-Side ISOdriver Si8235 in wide-body SOIC-16 package, 2-input, 4 A, 5 kV Dual ISOdriver High-side and low-side land pads for surface mount packaged FET/IGBT power transistors (not populated) High-side and low-side land pads for through-hole packaged FET/IGBT power transistors (not populated) Patch area The Si82xx board is four separate evaluation boards in one, with each section featuring a different ISOdriver (Si8220, Si8233, Si8234, or Si8235). Each section is isolated from the other sections and requires its own power supplies to power the given section's ISOdriver. Each section's ISOdriver is designed to be powered separately with input supplies for VDDI (5.5 V, 500 mA) and output supplies for VDDA, VDDB, or VDD up to 24 V. The user is expected to connect their desired drive-trane topology and load to the outputs of the appropriate ISOdriver and the patch area. Figure 2 shows a silkscreen overview of the board. Please note the voltage rating for the prepopulated components in the Si82xx BOM section of this document before applying power to the ISOdriver and customer specific driver-trane. Applying a voltage to a component that is higher than its rating can cause permanent device damage. If the install components do not meet the user's requirements, these components need to be replaced before proceeding. Moreover, if a user wants to evaluate an ISOdriver in a wide-body package other than the ones populated, this can be accomplished by removing the footprint-compatible device installed on the evaluation board and replacing it with the desired footprint-compatible ISOdriver. Rev. 0.1 3 Si82xx-EVB UG Figure 2. Si82xx Evaluation Board Silkscreen 4 Rev. 0.1 Si8 2 x x -E VB U G 3.1. Si82xx ISOdriver Board Test Figure 3 illustrates the Si8234 with VDDI powered from 5 V and VDDA and VDDB powered from 15 V. A 10 kHz signal is applied to the Si8234's PWM input. As shown, the Si8234 transmits a 10 kHz signal to VOA and VOB (Channel 3 illustrates VOA output, and Channel 2 illustrates VOB output). Note that VOA and VOB are 180° out of phase, as would be expected of a PWM driver. In this setup, no drive-trane was connected to the outputs (VOA and VOB) of the Si8234. Nevertheless, the potentiometer, R35, can be adjusted to dynamically change the dead-time of the Si8234 if desired. Duplicating this setup is an excellent test to become familiar with the evaluation board. To repeat this test, perform the following steps: 1. Install a shunting jumper to J12 (Position 1, 2). 2. Install a shunting jumper to J14. 3. Install a shunting jumper to J11. 4. Install a shunting jumper to J13. 5. Connect a 5 Vp-p square wave to P7. 6. Connect a 5 V (100 mA) supply to P9. 7. Connect a 15 V (100 mA) supply to P14. 8. Connect a 15 V (100 mA) supply to P15. 9. Connect a scope probe to TP9 to view VOA. 10.Connect a scope probe to TP11 to view VOB. Figure 3. Si8234 PWM Outputs Rev. 0.1 5 Si82xx-EVB UG Figure 4. Si82xx Evaluation Board Schematic (1 of 4) 4. Si82xx Evaluation Board Schematics 6 Rev. 0.1 Figure 5. Si82xx Evaluation Board Schematic (2 of 4) Si8 2 x x -E VB U G Rev. 0.1 7 Figure 6. Si82xx Evaluation Board Schematic (3 of 4) Si82xx-EVB UG 8 Rev. 0.1 Figure 7. Si82xx Evaluation Board Schematic (4 of 4) Si8 2 x x -E VB U G Rev. 0.1 9 Si82xx-EVB UG 5. Si82xx Evaluation Board Layout Figure 8. Si82xx Top Layer 10 Rev. 0.1 Si8 2 x x -E VB U G Figure 9. Si82xx Bottom Layer Rev. 0.1 11 Si82xx-EVB UG 6. Bill of Materials Table 1. Si82xx-EVB Bill of Materials Item Qty Ref Part Number Mfr Description 1 10 C1, C4–5, C8–9, C12, C22, C24, C26, C28 311-1140-2-ND Digikey Cap, 0.1 µF, X7R, Ceramic, 50 V, 0805, ±10%, or eq, RoHS 2 2 C7, C11 PCC2249CT-ND Digikey Cap 1.0 µF, X5R, Ceramic, 0805, 16 V, ±10%, or eq, RoHS 3 1 C3 PCC1893CT-ND Digikey Cap 1.0 µF, X7R, Ceramic, 1206, 25 V, ±10%, or eq, RoHS 4 3 C2, C6, C20 490-1809-1-ND Digikey Cap 4.7 µF, X7R, Ceramic, 1206, 25 V, ±10%, or eq, RoHS 5 4 C23, C25, C27, C29 490-1809-1-ND Digikey Cap 4.7 µF, X7R, Ceramic, 1206, 25 V, ±10%, or eq, RoHS, no-pop 6 7 C10, C14–19 CAP 0805 Digikey Cap, NO POP, 0805, or eq, RoHS 7 7 Q3–4, Q7–8, Q11–12, Q15 D2-PAK-NO-POP D2-pak-no-pop D2-PAK-NO-POP or eq, RoHS 8 4 D1–3, D7 US1K-FDICT-ND Digikey Diode, SW ULT FAST, 1 A, 800 V, SMA, RoHS 9 25 J2–7, J9– 11, J13–17, J19–25, J56–57, J74–75 S1011E-02-ND Digikey Stake Header, 1X2, 0.1"CTR, Gold, or eq, RoHS 10 112 J26–55, J58–73, J76–78, J80–139, J168–169, J171 NO-POP None No-pop, RoHS 11 4 J1, J8, J12, J18 S2011E-02-ND Digikey Stake Header, 2X2, 0.1"CTR, Gold, OR Eq, RoHS 12 2 R23, R35 92W-104LF-ND Digikey Pot, 100 kRes, 3/8" SQ CERM SL, MT, TOP ADJ, ±10%, OR EQ, RoHS 13 1 R42 P100ACT-ND Digikey Res, 100 , SMT, 0805, 1/8W, ±5%, OR EQ, RoHS 12 Rev. 0.1 Si8 2 x x -E VB U G Table 1. Si82xx-EVB Bill of Materials (Continued) Item Qty Ref Part Number Mfr Description 14 3 R1, R12, R24 P10.0KCCT-ND Digikey Res, 10.0 k, SMT, 0805, 1/8 W, ±1%, or eq, RoHS 15 1 R39 311-237CRCT-ND Digikey Res 237 , SMT, 0805, 1/8W, ±1%, or eq, RoHS 16 1 R41 311-330ARCT-ND Digikey Res, 330 , SMT, 0805, 1/8W, ±5%, or eq, RoHS 17 5 R9, R11, R20, R22, R32 RHM470ACT-ND Digikey Res, 470 , SMT, 0805, 1/8W, ±5%, or eq, RoHS 18 6 R8, R10, R19, R21, R31, R40 P49.9CCT-ND Digikey Res, 49.9 , SMT, 0805, 1/8W, ±1%, or eq 19 21 R2–7, R13–18, R25–30, R36–38 NO POP Digikey Res, no pop, SMT, 0805, or eq, RoHS 20 1 U4 Si8220BD-A-IS Silicon Labs IC, 2.5 A, 5 kV, ISOdrivers with Opto Input, RoHS 21 1 U2 Si8233BD-C-IS Silicon Labs 4.0 A, 5 kV, ISOdrivers, RoHS 22 1 U3 Si8234BD-C-IS Silicon Labs IC, 4.0 A, 5 kV, ISOdrivers, RoHS 23 1 U1 Si8235BD-C-IS Silicon Labs IC, 4.0 A, 5 kV, ISOdrivers, RoHS 24 4 RF1–4 SJ5744-0-ND Digikey Bumpon protective, bumper , Silicone, or eq, RoHS 25 14 TP1–11, TP13, TP15–16 No Pop Digikey Test point, PC compact, no pop, or eq, RoHS 26 7 Q1–2, Q5–6, Q9–10, Q13 TO220-NO-POP To220-no-pop TO220-no-pop, or eq, RoHS 27 13 P2–3, P5–15 277-1236-ND Digikey Conn Term Block, 5.08 mm ctrs, PCB, 2 POS, RoHS 28 2 P1, P4 277-1249-ND Digikey Conn Term Block, 5.08 mm ctrs, PCB, 4 POS, RoHS 29 1 Q14 ZXM61N02FCT-ND Digikey Mosfet, N-Chan, 20 V, 1.7 A, SOT23-3, RoHS Rev. 0.1 13 Si82xx-EVB UG 7. Ordering Guide Table 2. Si82xx Evaluation Board Ordering Guide 14 Ordering Part Number (OPN) Description Si82xx-KIT Si82xx CMOS ISOdriver evaluation board kit Rev. 0.1 Si8 2 x x -E VB U G NOTES: Rev. 0.1 15 Smart. Connected. Energy-Friendly Products Quality www.silabs.com/products www.silabs.com/quality Support and Community community.silabs.com Disclaimer Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Trademark Information Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®, USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders. Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 USA http://www.silabs.com