Si3459-KIT User's Guide

Si3459-KIT
Si3459 E VALUATION K I T U SER ’ S G UIDE
1. Introduction
The Si3459 16-port evaluation kit (Si3459-KIT) is intended for Power over Ethernet (PoE) Power Sourcing
Equipment (PSE) system designers interested in evaluating the 8-port Si3459 PSE controller.
The Si3459 is controlled through an I2C (or SMBus) interface. For convenience in evaluation, a graphical user
interface (GUI) is provided, giving an easy-to-use visual display and control of the Si3459 I2C registers. The
evaluation kit assumes the user has access to a PC to control the evaluation board using the provided GUI.
The user is also responsible for providing an appropriate high-voltage power supply. The power supply should be
45 to 57 V for normal PoE or 51 to 57 V for PoE+. The Si3459 can supply over 30 W to each port. Thus, the two
Si3459 controllers for the 16-port demo system can provide over 480 W of total power. While the classification and
actual current consumption of each port is available, the demo GUI interacts with the Si3459 on a per-port basis
and does not implement system-level power management. Contact Silicon Laboratories for more information about
system-level power management options.
The Si3459-KIT kit has been thoroughly tested for standards compliance and interoperability. Contact Silicon
Laboratories for test reports using Sifos PoE test equipment and University of New Hampshire PoE standards
compliance and interoperability reports.
Confidential Rev. 0.3 10/15
Copyright © 2015 by Silicon Laboratories
Si3459-KIT
Si3459-KIT
2. Kit Contents
Table 1. Evaluation Kit Contents
2
Qty
Item
Contents
1
Si3459-EVB
Si3459 16-port evaluation board with connector for an external 50 V
power supply. The power supply must be capable of supplying the
required amount of power for all PoE loads being connected. The board
is populated with Si3459 parts.
2
Si3459CB-EVB
2
RIBBON-20-4
1
USB-ADAPT-BRD
1
S-USB2.06-01
2
Si3402ISO-EVB
Powered Device evaluation board configured to provide a Class 3 signature.
1
Si3402ISO-C4-EVB
Powered Device evaluation board configured to provide a Class 4 signature.
3
LOADBOARD_REV1_0
6
HEXNUT 1/4-32_NIC
1
CON-2-MALE
3
CAT5E-01
Ethernet cable to connect the Si3402 evaluation boards to the connector
board.
1
CD-ROM
Software drivers for the USB to I2C adapter and a GUI for the Si3459
registers on a CD-ROM. Applicable notes and data sheets are also
included.
RJ-45 connector board configured as Power over Ethernet mid-span
injector with gigabit Ethernet pass-through.
20-wire cable connects the Si3459 evaluation board to the RJ-45 connector board
USB to I2C (or SMBus) translator board. This board is preprogrammed to
support I2C transactions. The label on this 2”x 2” board is “PoE USB
Adapter”.
USB cable to connect to a host PC
Configurable load board.
Nuts for attaching load boards to powered device evaluation boards
Power connector to fit EVB J3
Confidential Rev. 0.3
Si3459-KIT
3. Installation
This KIT includes a PC-based Monitor GUI. Before you can use the Monitor, you must first install the device driver
associated with the PoE USB Adapter card (called “PoEUSB” in this document), then install the Monitor GUI.
3.1. Installing the PoEUSB Device
Note: If you have previously installed the PoEUSB device, uninstall the previous driver version before installing the new version. To uninstall the previous version, select “Programs and Features” or “Add or Remove Programs” from the Control
Panel, and then uninstall “Windows Driver Package - Silicon Labs, (WinUSB) MultiportSerial” and similar file names.
Figure 1. Uninstall Previous Revision Windows Driver Package
To install the PoEUSB device driver, run PoEUSBSetup.exe from the documentation that comes with this KIT.
Figure 2. PoE USB Device Installer Screen
After the PoEUSB device driver is installed, then complete the installation by connecting the PoEUSB adapter card
to the PC with a USB cable.
Confidential Rev. 0.3
3
Si3459-KIT
3.2. Installing the Si3454 & Si3459 Monitor
If you have previously installed the Monitor, uninstall the previous version before installing the new version. To
uninstall the previous version, select “Programs and Features” or “Add or Remove Programs” from the Control
Panel, and then uninstall the application.
Figure 3. Uninstall Previous Rev Si3454 & Si3459 Monitor
To install the Si3454 & Si3459 Monitor, run si3454_si3459_monitor.msi.
Figure 4. Monitor Setup Wizard
4
Confidential Rev. 0.3
Si3459-KIT
4. Hardware Installation
Figure 5 shows how all the hardware components of the Si3459 evaluation kit fit together.
Figure 5. Evaluation Kit Hardware
Reference Figure 5 for overall system connection. Perform initial setup as follows:
1. Verify that Evaluation Board jumper placements are correct, according to Figure 18 schematic, Figure 6.
“Si3459 Jumpers” and Table 2. On the Connector Board, the default condition occurs when all jumpers are
installed.
2. Connect the Si3459 evaluation card (Si3459-EVB) to the two RJ45 (Si3459CB-EVB) cards using the
20-pin ribbon cables.
3. Plug J104 (refer to the silkscreen on the bottom of the board) of the PoEUSB adapter into J2 of the
Si3459-EVB.
4. Connect a 52 V power supply to J3. When the high voltage supply is turned on, the power LED D3 will
indicate that the on-board generated 3.3 V logic supply is active. The power LED location is indicated by
green circles in Figure 6. “Si3459 Jumpers”.
5. Plug the PoEUSB adapter into an available computer USB port if this was not already done during the
software installation step. If the drivers were installed properly, the PC should recognize the adapter.
6. The Si3459 Evaluation Board is configured as a midspan power injector. The data input lines are on the top
row, and the power plus data output lines are on the bottom row. See Figure 7. A Powered Device (PD) is
plugged into the bottom row.
7. Start the Si3454 & Si3459 Monitor.
Confidential Rev. 0.3
5
Si3459-KIT
Figure 6. Si3459 Jumpers
Table 2. Si3459-EVB Jumper Table
Jumper
6
Function
Initial Setting
J1
Si3459 U12 address
0,0,0,0
J5
Si3459 U11 address
0,0,0,1
J10
Auto mode selection
1,1,1,1
JP3
Assert reset from host voltage domain
OFF
JP6
Debounce reset from SW1
ON
JP7
Enable buck converter
ON (1,2)
JP8
Disable buck converter
ON
JP9
Isolate buck components when chained
ON
JP10
Isolate buck components when chained
ON
JP11
Remove pullup for chained operation
ON
JP12
Remove pullup for chained operation
ON
JP13
Force shutdown
OFF
JP14
Breaker for isolated Reset line. Remove when
chained and/or PoEUSB is not connected.
OFF
Confidential Rev. 0.3
Si3459-KIT
Port 1
Data in
Port 8
Data in
Port 1
PoE and
Data out
Port 8
PoE and Data out
Figure 7. Connector Board Configuration
EVB board connector J8 supports chaining multiple Si3459 boards together to demonstrate and test configurations
with larger numbers of Si3459 devices. Chaining is done with a standard 0.1 inch spacing ribbon cable. Using
jumpers, switching supplies on chained boards should be disabled. Redundant I2C pullups may be disabled as
well. Consult with Silicon Labs applications engineering for further details.
Confidential Rev. 0.3
7
Si3459-KIT
5. Using the Si3454 & Si3459 Monitor
To run the Si3454 & Si3459 Monitor, double click on the “Si3454 & Si3459 Monitor” desktop icon. You may also run
the Si3454 & Si3459 Monitor from the Start menu, by selecting: StartAll ProgramsSilicon
LaboratoriesSi3454 & Si3459 Monitor. Figure 8 shows the Si3454 & Si3459 GUI when it is initially opened.
The version of the Monitor is displayed in the upper left corner of the window.
Figure 8. Si3454 & Si3459 Monitor GUI
5.1. Interface Selector
Ensure that the Interface Selector in the lower left of the monitor window indicates “Interface: PoEUSB”. If it shows
“Interface: Dummy”, you have not successfully installed and connected to the PoE USB interface adapter.
Figure 9. Interface Selector
The Interface Selector specifies which USB-to-I2C converter device to use for communicating with the Si3459 PSE
controllers. The Si3454 & Si3459 Monitor supports several different USB-to-I2C converter devices. If more than
one of these devices is connected to the PC at the same time, then the user can select which one to use with the
Interface drop-down box.
The “Dummy” device is a substitute device that does not actually perform I2C communications. The Dummy device
allows the Si3454 & Si3459 Monitor to be opened and perform in an emulation mode even if there are no
USB-to-I2C converter devices connected to the PC.
8
Confidential Rev. 0.3
Si3459-KIT
5.2. Si3454 & Si3459 Monitor Layout
Along the top are monitor controls. On the left side are Si3459 global identification, power information and settings.
Immediately to the right are events and interrupts. On the right side all the Si3459 registers are individually
accessible. The middle section provides a graphical interface to the Si3459 registers. Changes made in either the
register or graphical view are instantly updated in the other view.
5.3. Monitor Control
The primary purpose of the Monitor Control area is to configure and control the operation of the GUI itself.
Figure 10. Monitor Control Area
The user may manually update the GUI by clicking the “Refresh” button. The GUI reads the Si3459 registers and
updates the displayed information.
The user may cause the GUI to automatically update itself at regular intervals by clicking on the “Start polling”
button. Once pressed, the button text changes to “Stop polling”. The green LED symbol on the Polling button
flashes red each time an update occurs. The “Poll delay” text box allows the user to specify the time between
updates. The user may stop automatic updates by clicking on the “Stop polling” button.
The user selects which Si3459 controller to use with the “Slave addr” box. Several Si3459 controllers may be
connected to the I2C bus. Each controller responds to two sequential I2C slave addresses corresponding to its two
quad-port sub-units or “quads”. The “Slave addr” box specifies which of the Si3459 controllers/quads to
communicate with. The GUI transacts with only one Si3459/quad at a time. The user may dynamically switch the
GUI between different Si3459/quads by selecting a new address in the “Slave addr” box corresponding to the
jumper setting on the Si3459-EVB (J1, J5).
If the user checks the “CoR” (Clear on Read) check box, then the GUI also reads the Si3459's CoR registers when
updating. If the CoR check box is not checked, then the GUI does not read the CoR registers when updating. The
CoR registers are the Global and the Port Event registers. Reading a CoR register has side effects: It clears that
register and clears the associated event bit in the interrupt register. Consequently, if the CoR check box is checked
while the GUI is polling, then events could come and go without being noticed by the user.
If the user checks the “RoM” (Read on Modify) check box, then the GUI automatically updates itself after the user
modifies a register via the GUI. The GUI automatically shows the effect of any change within a time delay, specified
by the “RoM delay” text box. The RoM behavior is only useful if polling is stopped.
The Monitor Control area has three buttons. The “SW Reset” button resets the selected quad of the Si3459 by
setting the “swrst” bit in the pb_global register. The “Shutdown low priority ports” button turns off all low priority
ports in the selected quad by setting the “lowpri” bit in the pb_global register. The “HW Reset” button causes a
reset pulse to be asserted on the Si3459 Reset pin. This fully resets all Si3459 devices on the board.
Confidential Rev. 0.3
9
Si3459-KIT
5.4. Device Information
The Device Information box displays high-level information about the Si3459 device, including hardware revision
and the firmware version.
Note: The example shown in Figure 11 is representative but may not contain the same data as that displayed with your board.
Figure 11. Device Information Box
5.5. Port Boxes
The port boxes display port status and have controls for configuring and controlling the ports. Each port has its own
box.
Figure 12. Port Box
5.5.1. Port Status
A port box displays the results of the last detection and last classification in the lower left. If not polling, the user
may manually update the port detect and classify status by clicking on the “R” (read) button.
Port voltage and current are displayed in the port box upper right corner. If polling is not enabled, then the user may
manually update the port voltage and current reading by clicking on the “Refresh” button.
5.5.2. Port Configuration
A port box contains four radio buttons to configure the mode of the port. The port mode may be Shutdown, Manual,
Semi-auto, or Auto.
The port features can be configured with the four checkboxes on the right pane. If “Disconnect enable” is checked,
the port removes power if the powered device is unplugged. If the “2 event class. enable” is checked, then the
Si3459 will follow the IEEE802.3at Type 2 (2-event) classification method for PDs presenting Class 4 signature
during the first event. The “2-event class” LED is lit when the Type 2 classification is successful.
The “Type2Fault” provides additional status information about the classification. The “FET Bad” LED is lit when the
external FET is damaged.
The following steps detail how a port can be manually turned on in the IEEE 802.3at Type 2 high-power manner
(see Figure 16 on page 16):
1. Enable detection and classification by checking the “Detect enable” and “Class enable” check-boxes.
2. Enable the 2 event classification by checking the "2 event class. enable" check box.
10
Confidential Rev. 0.3
Si3459-KIT
3. Watch for a successful 2 event classification by checking the state of the “2-event class.” LED
4. Once the classification is successful, set the Ilim to 850 mA
5. Set the proper Icut limit (see below) according to the available power
6. Turn on the port using the “On” pushbutton.
If “Low priority” is checked, the port immediately removes power if the “Shutdown low priority ports” button is
clicked. If “Legacy enable” is checked, then the port supplies power to a legacy powered device even though the
powered device does not provide a valid detection resistance. The “Legacy enable” check box supports
compatibility with certain older PD devices. Please consult the Si3459 data sheet for details. Checking “Midspan
backoff” allows selection of midspan type Alternative B detection back-off timing.
The user may configure a port's Icut level with the “Icut (mA)” drop-down box. The port automatically removes
power if the port current is greater than the Icut level for more than 60 ms.
5.5.3. Port Control
A port box contains three buttons for controlling a port. The “On” button forces a port to supply power; the “Off”
button forces a port to remove power, and the “Reset” button resets a port. Detect and Class buttons force a single
detection or classification operation.
5.6. Interrupts and Events
The Si3459 detects multiple events based on state of the device in general and its ports. Events may be
configured to generate interrupts. The GUI displays events, allows individual interrupts to be enabled and disabled,
and displays the status of interrupts.
5.6.1. Interrupt Enable
The Interrupt Enable box shown in Figure 13 specifies which events cause the Si3459 to generate an interrupt.
If the interrupt line is active, the Interrupt Line Active bar at the bottom of the Interrupts box is bright red instead of
dark red. Note that if there are multiple Si3459 controllers in the system, one or more of these controllers may be
pulling the interrupt line low. It may not be the currently-selected Si3459 that is making the interrupt line active.
Confidential Rev. 0.3
11
Si3459-KIT
Figure 13. Interrupt Enable and Events Boxes
5.6.2. Events
The Events box shown in Figure 13 displays the status of the interrupt line and the port events. The GUI events
section indicates both global and port-specific events. Each events register consists of a pair of read-only (RO),
and clear-on-read (CoR) registers with the same event bits. Reading the RO register obtains the bit values but
does not affect the bits. Reading the CoR register obtains the values of the bits, and also clears the bits in both the
RO and CoR registers. The indicators in the GUI Events section show the values from the RO register if the RO
register is read by push of the “R” button or by polling.
Events enabled to cause an interrupt will propagate to the interrupt active indicator, but will only be reflected in the
remainder of the GUI when the RO registers are read. For the best real-time view of the Si3459 events bits, it is
recommended to enable polling.
5.7. Register List
The Register List shown in Figure 14 displays the contents of the Si3459 registers and allows the user to change
the register contents.
12
Confidential Rev. 0.3
Si3459-KIT
Figure 14. Register List
The Register List displays all of the Si3459’s registers grouped by category. Each category of registers can be
expanded and collapsed by clicking on the plus and minus signs at the left edge of the Register List.
Next to the register name, the type of each register is displayed. Each register is either RW (read/write), RO (read
only), WO (write only) or CR (Clear on Read). WO registers reflect the value applied by the user.
Confidential Rev. 0.3
13
Si3459-KIT
The user may specify which registers to read (when the GUI is updated) by checking a box at the left of each
register name. Refreshing, polling, and RoM, all depend on these settings. Clear on Read registers are read only if
both the CoR check box is checked and the check box for the individual CR register is checked.
The user may read and write individual registers by using the “R” (read) and “W” (write) buttons at the right edge of
each register. The “R” and “W” buttons are disabled if the operation is not allowed for the type of register. The
display of the whole register file can be read and updated at once by clicking on the “Refresh” button.
The Register List displays the value of each register in binary and hexadecimal form. If a register has not yet been
read, then its binary value is displayed as all Xs, and its hexadecimal value is blank.
A register's hexadecimal value is displayed in a text box. If a register is not writable (RO or CR), then its text box is
gray and its hexadecimal value cannot be changed by the user. If a register is writable (RW), then its text box is
white and its hexadecimal value can be changed by the user. After changing a register's value, the user clicks on
the register's “W” button to write the new value to the register.
14
Confidential Rev. 0.3
Si3459-KIT
6. Operating the System
Each RJ45 connector board has eight LEDs for the eight ports. Each LED is driven by a comparator circuit which
detects when a voltage is forced to the load at the PoE output. When the ports are in auto mode, the LEDs in the
RJ45 connector board flash, indicating the detection cycle until a valid PD is connected. Once a valid PD is
connected and the port is turned on, the LEDs will glow steadily until the PD is disconnected. Once the PD is
connected, the port current will be displayed on the GUI. Note that the comparator circuits load the ports slightly,
and the LEDs dissipate power from the 3.3 V rail. If performing calibrated tests, it may be desirable to isolate the
comparator circuitry and eliminate any loading. This may be done by removing all jumpers from the connector
board.
The easiest way to get started is to put all of the ports in Auto mode. In Auto mode, detection, classification, power
management based on classification (Icut setting), disconnect (when enabled by “Dis Enable”), fault protection,
fault recovery, and port monitoring all happen without user intervention. Figure 15 shows the result of putting Port 1
in Auto mode. Circles indicate the required settings, and the squares indicate that a PD connected to the port has
been detected, classified, and powered. Auto mode may also be enabled on all ports by configuring J10 and
resetting the board by pressing SW1 or cycling power.
The Si3459 normally operates in manual or semi-automatic mode with the AUTO pin is held low. If a positive
voltage is applied to the AUTO pin, the Si3459 enters into fully autonomous operation, independent of a host. The
Si3459 also features dc disconnect detection algorithms to determine when a PD device is disconnected from any
of the eight independent ports. The AUTO mode can be set via the AUTO pin or from the host via I2C. At power-up,
the Si3459 reads the voltage on the AUTO pin (which can be set by a resistor divider from VDD to GND). If a
positive voltage is applied, the Si3459 enters into AUTO mode (all ports operate fully autonomously). The AUTO
pin voltage level configures the Si3459's behavior to register default values. For additional detail on Auto Pin
Configurations, refer to Section 3.2 Operating Modes in the Si3459 data sheet.
If the GUI is left in polling mode, the port status, port current, port voltage are all automatically updated by polling
the appropriate registers of the Si3459.
The Si3459 itself normally powers up as Alternative A, with no detection back-off, meaning the detect function
cycles at its highest rate. This is the most common usage for the Si3459. The RJ-45 connector board for the
evaluation kit is configured to inject the power on the “spare pairs” of the Ethernet cable, which is the Alternative B
or “Midspan” connection. Detection back-off is intended to ensure that a midspan and an endpoint do not compete
with each other and result in a failure to provide power. With detection back-off, the time between detection pulses
is increased to just over two seconds so as not to compete with the normal (approximately three times per second)
detection of an endpoint. If detection back-off is required, click the “Midspan” button to toggle this mode. You will
see that the LEDs on the connector board now flash at the slower detection speed. To toggle the mode back to
standard detection timing, click the button again.
The Si3459 in auto mode is fully-compliant with the 802.3at standard (often called PoE+), which allows up to 30 W
to be delivered over the Ethernet cable. In host-controlled mode, to enable the higher power support for a given
port, it is necessary to make multiple selections as described in "5.5.2. Port Configuration" on page 10. When Auto
mode is selected by the Auto jumper, the Si3459 automatically performs the two-event classification and increases
the cut-off current if a Class 4 PD is detected. The Si3402 evaluation board provided with the kit is configured to
provide the Class 4 signature; so, if the PoE+ mode is enabled and the Si3402 is plugged in, the cut-off current is
automatically set to 643.2 mA. Figure 16 shows the result of plugging in a Class 4 PD (into Port1) with PoE+ power
enabled. Class 4-specific settings and results are highlighted.
Confidential Rev. 0.3
15
Si3459-KIT
Figure 15. Example Result of Device Connection in Port Auto Mode
Figure 16. Class 4 Connection
16
Confidential Rev. 0.3
Si3459-KIT
7. Board Schematics, BOM, and Layout
The following are general PCB layout considerations. Detailed schematics, BOM, and layout can also be found in
the following sections. Visit the Silicon Labs Technical Support web page and register to submit a technical support
request, particularly if you are not closely following the recommended reference design.
7.1. Design and Layout Considerations
The Si3459 directly drives and senses detection and classification stimulus voltages. PoE power is enabled
through external FETs. PoE power supply currents in each channel are sensed using current shunt resistors with
sensed voltage referenced to GND.
Normally the layout will be 4-layer, with dedicated VPWR and GND planes for PoE power delivery. The ground
power plane does not generally have a high frequency content; so, it is acceptable to use a single GND plane and
tie GND, AGND, DGND pins to it. The thermal pad of the Si3459 is connected to GND. Si3459 internal dissipation
is modest, but for best performance the layout should include a thermal bond consisting of multiple vias between
the thermal pad and GND. The PoE power MOSFETs carry up to 800 mA dc and up to 5 A in faults; so, a 20 mil
trace with wide or multiple vias is also recommended.
The Si3459 includes a buck type dc-dc converter controller function, which generates a raw ~4 V power rail VCAP.
The buck regulator is able to supply 200 mA; so, within a group of Si3459 devices, only one buck regulator is
required. The single buck regulator supplies low drop-out (LDO) regulators within individual Si3459 devices to
generate their VDD = 3.3 V. Each LDO supplies the 3.3 V requirements of its own Si3459. The Si3459 VDD LDO is
able to supply additional current for an external device, such as an isolator or low-power-management
microcontroller.
The Si3459 buck regulator is a potential EMI source. The power devices, e.g. switching MOSFET, inductor, diode
and output capacitor should be located as close together as possible to minimize loop area. The entire switching
circuit should be shielded from Si3459 port connections to minimize the chance of interference.
To improve sensing accuracy, the Si3459 provides Kelvin connections for the resistor low side sense. The SENSEx
signals are connected to GND potential, but for best performance they should be routed separately from the GND
plane.
To avoid coupling between surge events and logic signals, it is recommended that VOUTn traces be well separated
from I2C interface pins.
A typical layer stackup is as follows:
1. Top: I2C, Si3459 Kelvin current sense
2. VPWR, VDD = 3.3 V
3. VEE = GND
4. Bottom: VOUT, switcher, VCAP
The I2C bus runs at 400 kHz maximum. The I2C bus lines should be routed away from analog lines like Rbias or
Vref but can otherwise be routed with ordinary care. If using a Silicon Labs I2C isolation product, please observe
the connections as per the reference design, which take into account required voltage margins and pullup values.
Confidential Rev. 0.3
17
Confidential Rev. 0.3
1
2
INPUT
POWER
CONN TRBLK 2
J3
C4
SW 1
JP6
2
4
6
8
10
JP3
2
4
6
8
10
D2
+3V3LV
GND
33uF
C9
+
TP8
BLACK
GND
0.1uF
C8
UNISOLATED
R5
1K
TP6
TP7
BLACK BLACK
GND
HEADER 5x2
1
3
5
7
9
MBRS3100T3
VPW R
1
3
5
7
9
J2
SW PUSHBUTTON
0.1uF
JS1
+3V3LV
680pF
C101
680pF
C102
C2
1uF
33uF
+ C11
TPV4
TPV3
NC
B4
B3
B2
B1
NC
2
4
6
8
10
12
14
16
33uF
VPW R
3.3V Status
C7
10uF
JP8
VPW R
FQT5P10
M1
JS5
+ C113
D3
GREEN
3.3V PW R
R17
330
L1
JP10
100uH
C110
10uF
10uF
C12
R16
0
JS6
JS16
D5
GREEN
3.3V PW R_1
R106
330
3.3V_1 Status
D4
ES1B
JP9
R134
1.0
VPW R
R2
10K
VPW R
JP7
Enable Buck for
Single Board JS4
Isolate Buck
Components
When Chained
Disable
Buck
CAP
/RESET
AUTO
/SHDN
SDA
SCL
/INT
10
SCL
11
JP14
JS7
Remove
Pullups
When
Chained
Disable Drive
When Chained
JS3
Disable Buck
when Chained
JP12
SDA
/INT
JS8
1K
JP11
1K
12
13
14
15
JS2
R4
R3
3
6
9
12
3
6
9
J5
JP13
R133
10K
11
10
8
7
5
4
2
1
R108
HEADER 4x3
+3V3_1
12
J1
10K
R1
11
10
8
7
5
4
2
1
JS12
JS11
JS10
JS9
C112
0.1uF
JS15
JS14
JS13
C111
0.1uF
SCL
SDA
/INT
/SHDN
0
/RESET
0.1uF
C3
Si3459
+3V3_1
AUTO
A1
A2
A3
A4
Si3459
AUTO
A1
A2
A3
A4
/SHDN
SWO
CAP
ISENSE
/DCEN
SCL
SDA
/RESET
/INT
Port_Drive_1
CAP
/SHDN
SWO
CAP
ISENSE
/DCEN
SCL
SDA
/RESET
/INT
Port_Drive_0
BLACK
TP4 RST
+3V3
VDD
ES1B
R132 0
HEADER 4x3
CAP
TP21
BLACK
+3V3
Figure 17. Evaluation Board Top Level
Inter-Board
Chain
J8
1
3
5
7
9
11
13
15
HEADER 8x2
TPV2
+3V3
TPV1
R18
44.2K
Isolation bypass
+3V3LV
Si8605
NC
A4
A3
A2
A1
NC
ISOLATION
BULK DECOUPLING
33uF
C10
+
7
6
5
4
3
2
U1
1
VDD1
GND1
8
16
VDD2
GND2
9
D1
+3V3
+3V3
+3V3
VPW R
VPW R
VOUT8
VOUT7
VOUT6
VOUT5
VOUT4
VOUT3
VOUT2
VOUT1
VOUT8
VOUT7
VOUT6
VOUT5
VOUT4
VOUT3
VOUT2
VOUT1
VOUT16
VOUT15
VOUT14
VOUT13
VOUT12
VOUT11
VOUT10
VOUT9
VOUT8
VOUT7
VOUT6
VOUT5
VOUT4
VOUT3
VOUT2
VOUT1
2
4
6
8
10
12
14
16
18
20
+3V3
2
4
6
8
10
12
14
16
18
20
VPW R
To PoE magnetics and LEDs
HEADER 10x2
1
3
5
7
9
11
13
15
17
19
J7
J10
HEADER 4x3
HEADER 10x2
1
3
5
7
9
11
13
15
17
19
J9
VPW R
To PoE magnetics and LEDs
+3V3
3
3.24K R139
+3V3
C1
1uF
+3V3
JS17
SDA
SCL
INT
TP1
TP2
TP3
BLACK BLACK BLACK
+3V3_1
6
6.49K R140
VPWR
VPWR
9
13.0K R141
GND
VDD
GND
12
1
2
4
5
7
8
10
11
26.1K R142
+3V3
+3V3_1
JS18
18
JS19
+3V3LV
Si3459-KIT
7.2. Si3459 Schematics
JS20
Confidential Rev. 0.3
GND
ISENSE
/DCEN
SWO
CAP
AUTO
A1
A2
A3
A4
SCL
/INT
/RESET
/SHDN
VPWR
GND
SDA
C19
10uF
GND
27
26
24
25
20
23
28
15
16
18
19
47
48
49
50
51
54
55
53
45
44
56
0.1uF
52
C20
0.1uF
VPWR
C18
0.1uF
C17
ISENSE
DCEN
SWO
CAP
NC
NC
NC
NC
NC
NC
NC
AUTO
A1
A2
A3
A4
SDAI
SDAO
SCL
INT
RESET
SHDN
NC
U2
17
VPWR
GND
Si3459
22
43
VDDA
VDD
GND
AGND
DGND
EPAD
21
46
VDD
29
30
31
32
33
34
35
36
37
38
39
40
41
42
1
2
3
4
5
6
7
8
9
10
11
12
13
14
TP25
GATE5
TP12
GATE3
R84
R81
0.25
0.25
R105
0.25
0.25
0.25
0.25
0.25
0.25
R102
R99
R96
R92
R87
TP26
TP27
TP28
GATE6 GATE7 GATE8
GND
TP10
GATE4
Q8 FDMC3612
Q7 FDMC3612
Q6 FDMC3612
Q5 FDMC3612
Q4 FDMC3612
Q3 FDMC3612
Q2 FDMC3612
Q1 FDMC3612
Figure 18. Si3459 Controllers (1 of 2)
GATE5
SENSE5
DRAIN5
KSENSC
DRAIN6
SENSE6
GATE6
GATE7
SENSE7
DRAIN7
KSENSD
DRAIN8
SENSE8
GATE8
GATE1
SENSE1
DRAIN1
KSENSA
DRAIN2
SENSE2
GATE2
GATE3
SENSE3
DRAIN3
KSENSB
DRAIN4
SENSE4
GATE4
TP9
TP11
GATE1 GATE2
C27
0.1uF
C26
0.1uF
C25
0.1uF
C23
0.1uF
C22
0.1uF
C21
0.1uF
C16
0.1uF
C15
0.1uF
VPWR
SMAJ58A
SMAJ58A
SMAJ58A
D28
D27
SMAJ58A
SMAJ58A
D26 SMAJ58A
D25 SMAJ58A
D24 SMAJ58A
D23
D22
D21
TP24
VOUT8
VOUT7
TP23
VOUT6
TP22
VOUT5
TP19
VOUT4
TP18
VOUT3
TP17
VOUT2
TP16
VOUT1
TP13
VOUT8
VOUT7
VOUT6
VOUT5
VOUT4
VOUT3
VOUT2
VOUT1
Si3459-KIT
19
Confidential Rev. 0.3
GND
ISENSE
/DCEN
SWO
CAP
AUTO
A1
A2
A3
A4
SCL
/INT
/RESET
/SHDN
VPWR
GND
SDA
C32
10uF
GND
27
26
24
25
20
23
28
15
16
18
19
47
48
49
50
51
54
55
53
45
44
56
0.1uF
52
C33
0.1uF
VPWR
C31
0.1uF
C30
ISENSE
DCEN
SWO
CAP
NC
NC
NC
NC
NC
NC
NC
AUTO
A1
A2
A3
A4
SDAI
SDAO
SCL
INT
RESET
SHDN
NC
U3
17
VPWR
GND
Si3459
22
43
VDDA
VDD
GATE5
SENSE5
DRAIN5
KSENSC
DRAIN6
SENSE6
GATE6
GATE7
SENSE7
DRAIN7
KSENSD
DRAIN8
SENSE8
GATE8
GATE1
SENSE1
DRAIN1
KSENSA
DRAIN2
SENSE2
GATE2
GATE3
SENSE3
DRAIN3
KSENSB
DRAIN4
SENSE4
GATE4
29
30
31
32
33
34
35
36
37
38
39
40
41
42
1
2
3
4
5
6
7
8
9
10
11
12
13
14
TP45
GATE5
TP32
GATE3
0.25
0.25
R131
0.25
0.25
0.25
R128
R125
R122
R118
0.25
R110 0.25
R107 0.25
R113
TP46
TP47
TP48
GATE6 GATE7 GATE8
GND
TP30
GATE4
Q16FDMC3612
Q15FDMC3612
Q14FDMC3612
Q13FDMC3612
Q12FDMC3612
Q11FDMC3612
Q10FDMC3612
Q9 FDMC3612
Figure 19. Si3459 Controllers (2 of 2)
GND
AGND
DGND
20
EPAD
21
46
VDD
TP29
TP31
GATE1 GATE2
C40
0.1uF
C39
0.1uF
C38
0.1uF
C36
0.1uF
C35
0.1uF
C34
0.1uF
C29
0.1uF
C28
0.1uF
VPWR
SMAJ58A
SMAJ58A
SMAJ58A
D36
D35
SMAJ58A
SMAJ58A
D34 SMAJ58A
D33 SMAJ58A
D32 SMAJ58A
D31
D30
D29
TP44
VOUT8
VOUT7
TP43
VOUT6
TP42
VOUT5
TP39
VOUT4
TP38
VOUT3
TP37
VOUT2
TP36
VOUT1
TP33
VOUT8
VOUT7
VOUT6
VOUT5
VOUT4
VOUT3
VOUT2
VOUT1
Si3459-KIT
Si3459-KIT
7.3. Si3459 Evaluation Board Layout
Figure 20. Evaluation Board Top Silkscreen
Confidential Rev. 0.3
21
Si3459-KIT
Figure 21. Evaluation Board Top Side
22
Confidential Rev. 0.3
Si3459-KIT
Figure 22. Evaluation Board Ground Layer
Confidential Rev. 0.3
23
Si3459-KIT
Figure 23. Evaluation Board Power Layer
24
Confidential Rev. 0.3
Si3459-KIT
Figure 24. Evaluation Board Bottom Side
Confidential Rev. 0.3
25
Si3459-KIT
7.4. Si3459 Bill of Materials
Table 3. Si3459 Evaluation Board Bill of Materials
Qty
Ref
Value
2
C1, C2
1 µF
4
C3, C8, C111,
C112
1
Tol
Type
PCB Footprint
Mfr Part Number
Mfr
16 V
±20%
X7R
C0805
C0805X7R160-105M
Venkel
0.1 µF
100 V
±20%
X7R
C0603
C0603X7R101-104M
Venkel
C4
0.1 µF
10 V
±10%
X7R
C0402
C0402X7R100-104K
Venkel
2
C7, C110
10 µF
10 V
±20%
X5R
C0805
C0805X5R100-106M
Venkel
4
C9, C10, C11,
C113
33 µF
100 V
±20%
Alum_Elec
C3.5X8MM-RAD
ECA2AM330
Panasonic
3
C12, C17, C30
10 µF
10 V
±10%
X5R
C0603
C0603X5R100-106K
Venkel
18
C15, C16,
C20, C21,
C22, C23,
C25, C26,
C27, C28,
C29, C33,
C34, C35,
C36, C38,
C39, C40
0.1 µF
100 V
±10%
X7R
C0805
C0805X7R101-104K
Venkel
4
C18, C19,
C31, C32
0.1 µF
16 V
±20%
X7R
C0603
C0603X7R160-104M
Venkel
2
C101, C102
680 pF
Y3
250 V
±15%
Y3
C1808
GA342QR7GD681KW01L
Murata
2
D1, D4
ES1B
1.0 A
100 V
Fast
DO-214AC
ES1B
Diodes Inc.
1
D2
MBRS3100T3
3A
100 V
Schottky
DO-214AB
MBRS3100T3
On Semi
2
D3, D5
Green
30 mA
2.2 V
SMT
LED-0805-K
LTST-C170GKT
Lite_On Inc.
16
D21, D22,
D23, D24,
D25, D26,
D27, D28,
D29, D30,
D31, D32,
D33, D34,
D35, D36
SMAJ58A
400 W
58 V
GP
DO-214AC
SMAJ58A
Littelfuse
9
JP3, JP6, JP8,
JP9, JP10,
JP11, JP12,
JP13, JP14
Jumper
Header
CONN1X2
TSW-102-07-T-S
Samtec
1
JP7
Header 1x3
Header
CONN-1X3
TSW-103-07-T-S
Samtec
26
Rating Voltage/
Current
Confidential Rev. 0.3
Si3459-KIT
Table 3. Si3459 Evaluation Board Bill of Materials (Continued)
Qty
Ref
Value
20
JS1, JS2, JS3,
JS4, JS5, JS6,
JS7, JS8, JS9,
JS10, JS11,
JS12, JS13,
JS14, JS15,
JS16, JS17,
JS18, JS19,
JS20
3
Rating Voltage/
Current
Type
PCB Footprint
Mfr Part Number
Mfr
Jumper Shunt
Shunt
N/A
SNT-100-BK-T
Samtec
J1, J5, J10
Header 4x3
Header
CONN3X4
TSW-104-07-G-T
Samtec
1
J2
Header 5x2
Header
CONN2X5
TSW-105-07-T-D
Samtec
1
J3
CONN TRBLK 2
Term Blk
Male
CONN-TB-175724
2
1757242
Phoenix
Contact
2
J7, J9
Header 10x2
Header
CONN2X10-2MM
TMM-110-01-T-D
Samtec
1
J8
Header 8x2
Header
CONN2X8-TSM
TSM-108-01-T-DV
Samtec
1
L1
100 µH
Shielded
IND-CTSLF1045
CTSLF1045-101M
Central
Tech
5
MH1, MH2,
MH3, MH4,
MH5
4–40
HDW
MH-125NP
NSS-4-4-01
Richco
Plastic Co
1
M1
FQT5P10
P-CHNL
SOT223-GDS
FQT5P10
Fairchild
1
PCB1
Si3459-EVB
Rev 2.0
Bare PCB
N/A
Si3459-EVB REV 2.0
SiLabs
16
Q1, Q2, Q3,
Q4, Q5, Q6,
Q7, Q8, Q9,
Q10, Q11,
Q12, Q13,
Q14, Q15, Q16
FDMC3612
12 A
N-CHNL
POWER33
FDMC3612
Fairchild
3
R1, R2, R133
10 k
1/10 W
±1%
ThickFilm
R0603
CR0603-10W-1002F
Venkel
3
R3, R4, R5
1k
1/10 W
±1%
ThickFilm
R0603
CR0603-10W-1001F
Venkel
2
R17, R106
330 
1/10 W
±1%
ThickFilm
R0805
CR0805-10W-3300F
Venkel
1
R18
44.2k
1/10 W
±1%
ThickFilm
R0603
CR0603-10W-4422F
Venkel
16
R81, R84,
R87, R92,
R96, R99,
R102, R105,
R107, R110,
R113, R118,
R122, R125,
R128, R131
0.25 
1/4 W
±1%
ThickFilm
R0805
LCR0805-R250F
Venkel
1.0 A
1.0 A
Tol
±20%
100V
100 V
Confidential Rev. 0.3
27
Si3459-KIT
Table 3. Si3459 Evaluation Board Bill of Materials (Continued)
Qty
Ref
Value
Rating Voltage/
Current
3
R16, R108,
R132
0
1A
1
R134
1.0 
1/4 W
1
R139
3.24 k
1
R140
1
Tol
Type
PCB Footprint
Mfr Part Number
Mfr
ThickFilm
R0603
CR0603-16W-000
Venkel
±1%
ThickFilm
R1206
CR1206-4W-1R00F
Venkel
1/10 W
±1%
ThickFilm
R0603
CR0603-10W-3241F
Venkel
6.49 k
1/16 W
±1%
ThickFilm
R0603
CR0603-16W-6491F
Venkel
R141
13.0 k
1/16 W
±1%
ThickFilm
R0603
CR0603-16W-1302F
Venkel
1
R142
26.1 k
1/16 W
±1%
ThickFilm
R0603
CR0603-16W-2612F
Venkel
5
SO1, SO2,
SO3, SO4,
SO5
Standoff
2397
SPC
Technology
1
SW1
SW Pushbutton
4
TPV1, TPV2,
TPV3, TPV4
40
HDW
Tactile
SW4N6.5X4.5-PB
101-0161-EV
Mountain
Switch
TPV
PCB Feature
VIA-TP
N/A
N/A
TP1, TP2,
TP3, TP4,
TP6, TP7,
TP8, TP9,
TP10, TP11,
TP12, TP13,
TP16, TP17,
TP18, TP19,
TP21, TP22,
TP23, TP24,
TP25, TP26,
TP27, TP28,
TP29, TP30,
TP31, TP32,
TP33, TP36,
TP37, TP38,
TP39, TP42,
TP43, TP44,
TP45, TP46,
TP47, TP48
Black
Loop
TESTPOINT
151-203-RC
Kobiconn
2
TP5, TP20
RED
Loop
TESTPOINT
151-207-RC
Kobiconn
1
U1
Si8605
Isolator
SO16N6.0P1.27
Si8605AC-B-IS1
Silicon Labs
2
U2, U3
Si3459-B02-IM
28
50 mA
12 Vdc
3750 VRMS
Confidential Rev. 0.3
Si3459-KIT
7.5. RJ45 Connector Board Schematics
POE_OUT
RTN1
RTN2
RTN3
RTN4
RTN5
RTN6
RTN7
RTN8
RTN1
RTN2
RTN3
RTN4
RTN5
RTN6
RTN7
RTN8
J1
RTN1
RTN2
RTN3
RTN4
RTN5
RTN6
RTN7
RTN8
2
4
6
8
10
12
14
16
18
20
1
3
5
7
9
11
13
15
17
19
VOUT1
VOUT2
VOUT3
VOUT4
VOUT5
VOUT6
VOUT7
VOUT8
VOUT1
VOUT2
VOUT3
VOUT4
VOUT5
VOUT6
VOUT7
VOUT8
POE_OUT
HEADER 10x2
VPWR
PoE LEDs
VPWR
+3V3
VOUT1
VOUT2
VOUT3
VOUT4
VOUT5
VOUT6
VOUT7
VOUT8
+3V3
GND
PoE LEDs
Figure 25. Connector Board Top Level
Confidential Rev. 0.3
29
VOUT8
VOUT7
VOUT6
VOUT5
VOUT4
VOUT3
VOUT2
VOUT1
Confidential Rev. 0.3
GND
VPWR
JS8
JS7
JS6
JS5
JS4
JS3
JS2
JS1
JP9
C200
1uF
JP8
JP7
JP6
JP5
JP4
JP3
JP2
JP1
GND
4.99M
R215
4.99M
R214
4.99M
R213
4.99M
R212
4.99M
4.99M
R211
R210
4.99M
R209
4.99M
R208
R200
200K
R201
200K
R202
200K
R203
200K
R205
200K
R206
200K
R207
200K
6 -
5 +
6 -
5 +
6 -
5 +
6 -
5 +
LMX393H
U204B
7
LMX393H
U203B
7
LMX393H
U202B
7
LMX393H
U201B
7
D201
GREEN
R217
332
CMP_REF
D203
GREEN
R219
332
D205
GREEN
R221
332
2 -
3 +
2 -
3 +
2 -
3 +
2 -
3 +
40.2K
R224
1M
R225
D208
5.1V
D207
GREEN
R223
332
D200
GREEN
R216
332
D202
GREEN
R218
332
D204
GREEN
R220
332
D206
GREEN
R222
332
This circuit facilitates visualization of PoE test voltages applied by
the PoE controller. It introduces some minor error in port detection
voltage, which may be eliminated by jumper disconnection. This
circuit is not intended to be included in production designs.
V- LMX393H
V+ U204A
1
V- LMX393H
V+ U203A
1
V- LMX393H
V+ U202A
1
V- LMX393H
V+ U201A
1
Figure 26. Connector Board Comparators and LEDs
R204
200K
Remove jumpers JP1...JP8 to prevent any loading
on the port. Remove JP9 to prevent LEDs from
turning on when JP1...JP8 are removed.
GND
JS9
8
4
8
8 4
4
8
30
4
+3V3
Si3459-KIT
Si3459-KIT
0.1uF
C319
F4
F5
RJ-45
F7
F8
VOUT3
RTN3
3
6
RJ-45
MX1+
MX1-
MX1+
MX1-
MX3+
MX3RJ-45
MX2+
MX2MX3+
MX3-
E4
E5
E7
E8
J300H
H1
H2
G3
G6
H3
H6
C320
0.1uF
C321
0.1uF
C322
0.1uF
C323
0.1uF
C327
H7
H8
RJ-45
6
VOUT4
L306B
VOUT7
RTN7
MX1+
MX1MX2+
MX2MX3+
MX3RJ-45
H1
H2
G3
G6
H3
H6
MX1+
MX1-
MX1+
MX1-
MX2+
MX2MX3+
MX3-
J301H
J301G
G1
G2
MX0+
MX0-
MX2+
MX2MX3+
MX3-
G4
G5
G7
G8
0.1uF
C328
0.1uF
C329
0.1uF
C330
0.1uF
C331
H4
H5
H7
H8
RJ-45
L306A
FA2536-ALD
F7
F8
RJ-45
MX0+
MX0-
RJ-45
RTN4
F4
F5
VOUT8
6
C326
1
F3
F6
1
C325
0.1uF
2
0.1uF
H4
H5
3
G7
G8
C324
4
MX3+
MX3-
0.1uF
5
MX2+
MX2-
G4
G5
J301F
MX0+
MX0-
L305A
L305B
FA2536-ALD
FA2536-ALD
J300G
G1
G2
MX1+
MX1-
1
E3
E6
L304A
L304B
FA2536-ALD
FA2536-ALD
MX0+
MX0-
FA2536-ALD
F1
F2
0.1uF
MX3+
MX3-
L303A
FA2536-ALD
MX0+
MX0-
MX2+
MX2-
RJ-45
RTN6
J301E
E1
MX0+ E2
MX0-
MX2+
MX2-
2
VOUT6
MX1+
MX1-
1
C318
D7
D8
MX0+
MX0-
L307A
FA2536-ALD
MX0+
MX0MX1+
MX1MX2+
MX2MX3+
MX3RJ-45
RTN8
1
0.1uF
C315
6
C317
0.1uF
1
0.1uF
2
E7
E8
F3
F6
4
MX3+
MX3-
E3
E6
E4
E5
J300F
F1
F2
5
MX2+
MX2-
C314
L303B
FA2536-ALD
J300E
E1
MX0+ E2
MX0-
C316
C313
0.1uF
L302A
FA2536-ALD
0.1uF
C7
C8
0.1uF
D4
D5
2
3
4
6
L302B
MX1+
MX1-
RJ-45
RTN2
MX3+
MX3-
C312
3
VOUT2
RJ-45
MX3+
MX3-
MX2+
MX2-
0.1uF
3
D7
D8
MX2+
MX2-
C4
C5
6
C311
D3
D6
MX1+
MX1-
1
0.1uF
2
C7
C8
C310
5
MX3+
MX3-
C309
0.1uF
D4
D5
C3
C6
MX1+
MX1-
MX3+
MX3-
J301D
D1
D2
MX0+
MX0-
MX2+
MX2-
RJ-45
J301C
C1
C2
MX0+
MX0-
MX1+
MX1-
FA2536-ALD
3
D3
D6
0.1uF
RTN5
MX0+
MX0-
L301A
4
J300D
C3
C6
MX2+
MX2-
RJ-45
FA2536-ALD
D1
D2
C308
B7
B8
VOUT5
L301B
J300C
C1
C2
0.1uF
C307
FA2536-ALD
MX0+
MX0-
C4
C5
0.1uF
L300A
FA2536-ALD
MX1+
MX1-
A7
A8
C306
4
L300B
RJ-45
MX3+
MX3-
0.1uF
B4
B5
4
6
RTN1
3
VOUT1
RJ-45
MX3+
MX3-
C305
3
B7
B8
0.1uF
6
C303
A4
A5
5
0.1uF
MX2+
MX2-
C304
5
C302
MX2+
MX2-
0.1uF
5
0.1uF
B4
B5
B3
B6
MX1+
MX1-
1
C301
2
A7
A8
0.1uF
4
MX3+
MX3-
A4
A5
C300
5
MX2+
MX2-
0.1uF
A3
A6
MX1+
MX1-
2
B3
B6
B1
B2
MX0+
MX0-
2
A3
A6
MX1+
MX1-
J301B
J301A
A1
A2
MX0+
MX0-
4
B1
B2
5
J300B
J300A
A1
A2
MX0+
MX0-
L307B
FA2536-ALD
FA2536-ALD
Figure 27. Connector Board Connectors and Coupling Circuits
Confidential Rev. 0.3
31
Si3459-KIT
7.6. Connector Board Layout
Figure 28. Connector Board Top Silkscreen
Figure 29. Connector Board Top Side
32
Confidential Rev. 0.3
Si3459-KIT
Figure 30. Connector Board Ground Layer
Figure 31. Connector Board Power Layer
Confidential Rev. 0.3
33
Si3459-KIT
Figure 32. Connector Board Bottom Side
34
Confidential Rev. 0.3
Si3459-KIT
7.7. Connector Board Bill of Materials
Table 4. Si3459 Connector Board Bill of Materials
Qty
Ref
Value
1
C200
32
Rating
Voltage/
Current
Tol
Type
PCB Footprint
Mfr Part Number
Mfr
1 µF
16 V
±20%
X7R
C0805
C0805X7R160-105M
Venkel
C300, C301,
C302, C303,
C304, C305,
C306, C307,
C308, C309,
C310, C311,
C312, C313,
C314, C315,
C316, C317,
C318, C319,
C320, C321,
C322, C323,
C324, C325,
C326, C327,
C328, C329,
C330, C331
0.1 µF
250 V
±20%
X7R
C1210
C1210X7R251-104M
Venkel
8
D200, D201,
D202, D203,
D204, D205,
D206, D207
Green
30 mA
2.2 V
SMT
LED-0805-K
LTST-C170GKT
Lite On
1
D208
5.1 V
500 mW
5.1 V
Zener
SOD-123
MMSZ4689T1G
On Semi
1
J1
Header
10x2
Header
CONN2X10-2MM
TMM-110-01-T-D
Samtec
2
J300
RJ–45
Receptacle
RJ45-8PORT
44170-0001
Molex
9
JP1, JP2,
JP3, JP4,
JP5, JP6,
JP7, JP8,
JP9
Jumper
Header
CONN1X2
TSW-102-07-T-S
Samtec
9
JS1, JS2,
JS3, JS4,
JS5, JS6,
JS7, JS8,
JS9
Jumper
Shunt
N/A
SNT-100-BK-T
Samtec
Ethernet
IND-FA2536
FA2536-ALD
Coilcraft
NSS-4-4-01
Richco
Plastic Co.
8
L300, L301, FA2536-ALD 675 µH
L302, L303,
L304, L305,
L306, L307
4
MH1, MH2,
MH3, MH4
4–40
5%
Shunt
HDW
Confidential Rev. 0.3
35
Si3459-KIT
Table 4. Si3459 Connector Board Bill of Materials (Continued)
Qty
Ref
Value
Rating
Voltage/
Current
8
R200, R201,
R202, R203,
R204, R205,
R206, R207
200 k
1/10 W
8
R208, R209,
R210, R211,
R212, R213,
R214, R215
4.99 M
8
R216, R217,
R218, R219,
R220, R221,
R222, R223
1
Type
PCB Footprint
Mfr Part Number
Mfr
±1%
ThickFilm
R0805
CR0805-10W-2003F
Venkel
1/8 W
±1%
ThickFilm
R0805
CR0805-8W-4994FT
Venkel
332 
1/10 W
±1%
ThickFilm
R0603
CR0603-10W-3320F
Venkel
R224
40.2 k
1/10 W
±1%
ThickFilm
R0603
CR0603-10W-4022F
Venkel
1
R225
1 M
1/10 W
±1%
ThickFilm
R0805
CR0805-10W-1004F
Venkel
4
SO1, SO2,
SO3, SO4
Standoff
HDW
2397
SPC_Technology
Technology
4
U201, U202,
U203, U204
LMX393H
Dual
SOT23-8N
LMX393HAKA-T
Maxim
36
714 mW
5.5 V
Tol
Confidential Rev. 0.3
Si3459-KIT
8. Ordering Guide
Due to the unique high-voltage and high-power design considerations, Silicon Labs recommends that the
reference designs be followed closely. Visit the Silicon Labs Technical Support web page and register to submit a
technical support request, particularly if you are not closely following the recommended reference design.
Table 5. Si3459-KIT Ordering Guide
Ordering Part Number
Description
Si3459-KIT
Evaluation board kit for Si3459, 16-port midspan evaluation board reference
design. Populated with Si3459 devices. Refer to the Si3459 data sheet Ordering
Guide section for current ordering and device configuration information.
Si3459-XYY-IM
Ordering part number for Si3459 devices.
X = device revision; YY = firmware revision.
Refer to the Si3459 data sheet Ordering Guide section for current ordering and
device configuration information.
Confidential Rev. 0.3
37
Si3459-KIT
APPENDIX—CHECKING WHETHER THE DRIVER IS INSTALLED
To check whether the driver is installed, open the Control Panel and click the Device Manager icon. The screen
shown in Figure 33 will appear. Click on “Multi-port serial adapters”, and, if it has installed, the driver will appear as
“Silicon Laboratories PoE USB Device”.
Figure 33. Device Manager
38
Confidential Rev. 0.3
Smart.
Connected.
Energy-Friendly
Products
Quality
Support and Community
www.silabs.com/products
www.silabs.com/quality
community.silabs.com
Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers
using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific
device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories
reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy
or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply
or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific
written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected
to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no
circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, Bluegiga, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®,
SiPHY®, Telegesis, USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or
registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders.
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
http://www.silabs.com