Terminal SSR G3S4 CSM_G3S4_DS_E_7_2 Compact Terminal SSR with 4 Outputs • Easy-to-use SSR block that combines four compact G3S SSRs, sockets, and heat sink in one unit. • Easy wiring with separate I/O terminal construction. • LED operation indicator. • Special socket used for easy Relay replacement. • Mounts either on DIN track or with screws. Ordering Information When your order, specify the rated voltage. ■ List of Models Contact configuration Heat sink Four SPST-NO relays Yes Built-in SSRs G3S-201PL-PD Zero cross function Applicable output load No Model 1 A at 75 to 264 VAC (See note 1.) G3S4-A 0.6 A at 75 to 264 VAC (See note 1.) G3S4-A1 Rated voltage 5 VDC 12 VDC 24 VDC No 5 VDC 12 VDC 24 VDC Yes G3SD-Z01P-PD 1 A at 3 to 26 VDC (See G3S4-D note 2.) 5 VDC 12 VDC 24 VDC No 0.6 A at 3 to 26 VDC (See note 2.) G3S4-D1 5 VDC 12 VDC 24 VDC Note: 1. Given as "250 VAC" on the G3S4. 2. Given as "24 VDC" on the G3S4. ■ Accessories (Order Separately) Connection Sockets (Can be Purchased Individually) Model P6BF-4BND Rated voltage Replacement Relays Model G3S-201PL-PD 12 VDC 5 VDC 12 VDC 24 VDC Heat Sinks (Can be Purchased Individually) Rated voltage 5 VDC 24 VDC G3SD-Z01P-PD 5 VDC 12 VDC 24 VDC Model Y92B-S10 1 G3S4 Specifications ■ Ratings Input (per G3S Relay) Rated voltage DC Operating voltage 5V Must operate level 4 to 6 VDC 4 VDC max. 12 V 9.6 to 14.4 VDC Must release voltage level 1 VDC min. 9.6 VDC max. 24 V 19.2 to 28.8 VDC 19.2 VDC max. Input impedance G3S4-A, G3S4-A1 Rated current G3S4-D, G3S4-D1 G3S4-A, G3S4-A1 G3S4-D, G3S4-D1 440 Ω±20% 550 Ω±20% 19.2 mA±20% 15.8 mA±20% 1 kΩ±20% 1.2 kΩ±20% 15.8 mA±20% 12.5 mA±20% 2.1 kΩ±20% 2.3 kΩ±20% 15.7 mA±20% 13.2 mA±20% Note: The rated current includes the terminal's LED current. Output (per G3S Relay) Model Applicable load G3S4-A Load voltage Load current 75 to 264 VAC Inrush current resistance 0.1 to 1 A G3S4-A1 15 A (60 Hz, 1 cycle) 0.1 to 0.6 A G3S4-D 3 to 26 VDC 0.01 to 1 A G3S4-D1 3 A (10 ms) 0.01 to 0.6 A ■ Characteristics Item Model G3S4-A, G3S4-A1 Must operate time 1 ms max. G3S4-D, G3S4-D1 Release time 0.5 × load power cycle + 1 ms max. 1 ms max. Output ON voltage drop 1.6 V max. (RMS) 1.5 V max. Leakage current 2 mA max. 0.1 mA max. (at 26 VDC) Insulation resistance 100 MΩ min. (at 500 VDC) Dielectric strength 2,000 VAC, 50/60 Hz for 1 min Vibration resistance 10 to 55 to 10 Hz, 0.75-mm single amplitude (1.5-mm double amplitude) Shock resistance 1,000 m/s2 Storage temperature −30 to 100°C (with no icing) Ambient operating temperature −30 to 80°C (with no icing) Ambient operating humidity 45% to 85% Weight Approx. 95 g (-A model) Approx. 95 g (-D model) Engineering Data ■ Reference Data (per G3S Relay) Load Current vs. Ambient Inrush Current Resistance Non-repetitive (Keep the inrush current to half the rated value if inrush current occurs Rated Temperature repetitively.) G3S4-A, G3S4-D 1 0.75 G3S4-A1, G3S4-D1 G3S4-D, G3S4-D1 Inrush current (A. Peak) Inrush current (A. Peak) Load current (A) G3S4-A, G3S4-A1 15 10 5 0 3 2 1 0 0.6 0.5 0.25 0.1 0 −30 −20 0 20 40 60 80 100 Ambient temperature (°C) 10 30 50 100 200 500 1,000 5,000 Energizing time (ms) 10 30 50 100 200 500 1,000 5,000 Energizing time (ms) Note: Measurement values taken from production line samples have been plotted in graphs to provide this data. Use this data only as a guide. Relays are mass-produced, so allowances must be made for a certain amount of variation in measurement data. 2 G3S4 Dimensions Note: All units are in millimeters unless otherwise indicated. ■ Relays With Heat Sinks 16-M3.5 43 max. G3S4-A G3S4-D 78 max. Mounting Holes (Top View) 4 Two, 4-dia. holes or M3.5 screw holes 43 max. 28 max. 33 max. 65±0.3 Without Heat Sinks 16-M3.5 36±0.2 G3S4-A1 G3S4-D1 78 max. Terminal Arrangement/Internal Connections (Top View) 4 43 max. 28 max. 33 max. 8 Output side ■ Accessories (Order Separately) Connection Socket (Can be Purchased Individually) − 4 7 + + 3 − 6 + 2 − 5 1 + 12 (+) 11 (+) 10 (+) 9 (+) 16 (−) 15 (−) 14 (−) 13 (−) Note: Make sure that the polarity of the input terminal is correct. The polarity given inside parentheses ( ) is for G3S4-D and G3S4-D1 Relays. There is no indication of polarity when Connection Sockets are used alone. 16-M3.5 P6BF-4BND (with operation indicator) − Input side 78 max. 4 43 max. 28 max. Heat Sinks (Can be Purchased Individually) Y92B-S10 Mounting Brackets 0 25−0.2 (3.5) 25 8.2 8.2 8.2 8.2 (7.5) 8.2 20 1+0.5 0 0 17−0.3 8 2 5 0 10−0.3 0.7 0.5 0 42−0.3 1 1 2 36±1 2 1 2 0.5 3 G3S4 Replacement Relays 10 max. 20 max. G3S-201PL-PD G3SD-Z01P-PD Terminal Arrangement/Connections (Bottom View) Relay Removal Tool and Short Bar (Order Separately) (−) 16.5 max. 16 max. Input voltage 4 0.8 10.16 7.62 1 (−) − INPUT (+) Load Load power supply (+) LOAD + 6 0.4 7.62 Refer to Options for the G6B-4CB, G6B4@@ND, and G3S4. Note: 1. The polarity given inside parentheses ( ) is for DC loads. 2. The load can be connected to ether the positive or negative SSR output terminal. Relay Mounting Products (Order Separately) Safety Precautions Refer to Safety Precautions for All Relays. ■ Precautions for Correct Use • The four SSRs are mounted individually. Use standard SSR connection methods. • There is almost no differences based on the mounting direction. Mount the Terminal SSR with the best air flow. • Apply a silicon grease for heat radiation (e.g., YG6260 or G746 from Shin-Etsu Chemical Co. Ltd.) between the heat sink and the SSR if the heat sink is removed during maintenance of the G3S4-A or G3S4-D Terminal SSR (with external heat sinks) or if an external heat sink that was purchased separately is mounted. • The load voltage cannot be increased by connecting the G3S4 load terminals in serial. This is because there is a small difference in the SSR operating time • The load current cannot be increased by connecting the G3S4 load terminal in parallel. This is because there is a small difference in the SSR operating time. • The P6BF-4BND Connection Socket has an operation indicator and is available in 5-VDC, 12-VDC, and 24-VDC models. • Use the P6B-Y1 Relay Removal Tool to remove SSRs. Mounted Relays Relays and SSRs cannot be mounted together. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. In the interest of product improvement, specifications are subject to change without notice. 4 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2015.10 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2015 All Right Reserved.