JULY, 2014 AATM3350 IsoPortTM Window INDEX FIXED WINDOW................................................................................. 3-5 SINGLE HUNG WINDOW................................................................ 6-10 DOUBLE HUNG WINDOW............................................................ 11-15 HORIZONTAL SLIDER WINDOW.................................................. 16-20 WIND LOAD CHARTS................................................................... 21-28 DEADLOAD CHARTS........................................................................ 29 RECEPTORS, SUB SILLS AND ANCHORING.................................. 30 THERMAL CHARTS...................................................................... 31-53 LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR. Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses ( ) are millimeters unless otherwise noted. The following metric (SI) units are found in these details: m –meter cm – centimeter mm –millimeter s –second Pa –pascal MPa –megapascal © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-063 1 Kawneer reserves the right to change configurations without prior notice when deemed necessary for product improvement. kawneer.com ADME050 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. AATM3350 IsoPortTM Window BLANK PAGE ADME050 kawneer.com © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 2 JULY, 2014 EC 97911-063 AATM3350 IsoPortTM Window JULY, 2014 EC 97911-063 FIXED WINDOW Standard Features • • • • • © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. • High Performance Commercial Window • IsoPortTM Thermal Break Screw and Spline Frame Corner Joinery Factory Silicone Glazed Interior Applied Glazing Bead Architectural Anodized Finishes and Applied Coatings Two Year Manufacturer's Warranty Exterior Interior Fixed Window For specific product applications, Consult your Kawneer representative. kawneer.com ADME050 Thermal Break 3 AATM3350 IsoPortTM Window JULY, 2014 FIXED WINDOW EC 97911-063 CLASS CW-PG50-FW / AW-PG50-FW OPTIONAL CLASS and GRADE CLASS AW-PG70-FW TESTING STANDARD AAMA / WDMA / CSA / 101 / I.S.2 / A440-08 (NAFS-08) FRAME DEPTH 3-1/2" Overall Frame Depth TYPICAL WALL THICKNESS .070" Nominal TYPICAL MAX. VENT SIZE 60" x 99" TYPICAL MIN. VENT SIZE 15" x 15" TYPICAL CONFIGURATIONS STANDARD INFILL OPTIONS 1" STANDARD HARDWARE Not Applicable OPTIONAL HARDWARE Not Applicable OTHER OPTIONS Between the Glass Muntin Grids Exterior Applied Muntin Grids Perimeters and Sills Exterior Pannings and Interior Trims True Intermediate Muntin Structural Mullions Vertically or Horizontally Stacked Strap Anchors Nailing Fin Flange FIXED WINDOW PRODUCT PERFORMANCE Air Infiltration NAFS-08 Water Resistance NAFS-08 Design Load NAFS-08 Thermal Transmittance AAMA 507 NFRC 100 Condensation Resistance* AAMA 1503 ≤ 0.10 Cfm/ft2 CW - 10 PSF AW - 15 PSF 50 PSF 70 PSF "U" Factor 0.33 to 0.56 CRF frame - 67 CRF glass - 71 Condensation Sound Temperature Transmittance** Index* ASTM E 1425 CSA A440.2 ASTM E 1332 I frame - 60 I glass - 62 STC - 36 OITC - 28 Note:"U" Values based on computer simulations utilizing Insulating Glass, Low E Coatings and Warm Edge Spacers. See Thermal Charts for various glass types. * CRF and Temperature index based on high performance Low E Glass and Warm Edge Spacers. ** Acoustical test based on laminated glass. ADME050 kawneer.com © Kawneer Company, Inc., 2014 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. CLASS and GRADE Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 4 © Kawneer Company, Inc., 2014 3/8" kawneer.com 3-1/2" 3-1/2" Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 1-13/16" 4 JAMB D.L.O D.L.O 3 3 SILL TYPICAL ELEVATION Log onto www.kawneer.com for other configurations 2-1/2" D.L.O 5 VERTICAL ADME050 D.L.O 1-13/16" D.L.O 6 D.L.O 4 2 HORIZONTAL 2-1/2" 5 D.L.O D.L.O W.D. W.D. O.D. O.D. 1-13/16" W.D. O.D. 1 HEAD O.D. 3/8" AATM3350 IsoPortTM FIXED WINDOW Standard Design W.D. 1 3/8" Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 AATM3350 IsoPortTM Window EC 97911-063 FIXED WINDOW SCALE : 3" = 1'-0" 3-1/2" 2 1-13/16" 6 JAMB 3/8" 5 AATM3350 IsoPortTM Window JULY, 2014 SINGLE HUNG WINDOW EC 97911-063 Standard Features Screw and Spline Frame and Sash Corner Joinery Factory Silicone Glazed Interior Applied Glazing Bead Architectural Anodized Finishes and Applied Coatings Two Year Manufacturer's Warranty Thermal Break Exterior Interior Single Hung Window For specific product applications, Consult your Kawneer representative. ADME050 kawneer.com © Kawneer Company, Inc., 2014 • • • • • Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. • High Performance Commercial Window • IsoPortTM Thermal Break Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 6 AATM3350 IsoPortTM Window JULY, 2014 SINGLE HUNG WINDOW CLASS and GRADE CLASS CW-PG50-H / AW-PG50-H OPTIONAL CLASS and GRADE CLASS AW-PG70-H (MAX. SIZE 52" X 99") TEST STANDARD AAMA / WDMA / CSA / 101 / I.S.2 / A440-08 (NAFS-08) FRAME DEPTH 3-1/2" Overall Frame Depth TYPICAL WALL THICKNESS .070" Nominal TYPICAL MAXIMUM SIZE 60" x 99" (AW), 56" x 91" (CW) TYPICAL MINIMUM SIZE 20" x 32-1/2" (10 PSF Sill), 20" x 33-1/2" (15 PSF Sill) TYPICAL CONFIGURATIONS STANDARD INFILL OPTIONS 1" STANDARD HARDWARE Heavy Duty Balances Zinc Die Cast Sweep Locks Sash Stops OPTIONAL HARDWARE Sill Auto Lock OTHER OPTIONS Between the Glass Muntin Grids Exterior Applied Muntin Grids Perimeters and Sills Exterior Pannings and Interior Trims Structural Mullions Vertically or Horizontally Stacked Strap Anchors Sill for 10 PSF or 15 PSF Water Performance Insect Screens Nailing Fin Flange SINGLE HUNG WINDOW PRODUCT PERFORMANCE © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-063 Air Infiltration NAFS-08 Water Resistance NAFS-08 Design Load NAFS-08 Thermal Transmittance AAMA 507 NFRC 100 Condensation Resistance* AAMA 1503 ≤ 0.30 Cfm/ft2 CW - 10 PSF AW - 15 PSF 50 PSF 70 PSF "U" Factor 0.38 to 0.57 CRF frame - 57 CRF glass - 60 Condensation Sound Temperature Transmittance** Index* ASTM E 1425 CSA A440.2 ASTM E 1332 I frame - 39 I glass - 58 STC - 36 OITC - 30 Note:"U" Values based on computer simulations utilizing Insulating Glass, Low E Coatings and Warm Edge Spacers. See Thermal Charts for various glass types. * CRF and Temperature index based on high performance Low E Glass and Warm Edge Spacers. ** Acoustical test based on laminated glass. kawneer.com ADME050 7 3/8" 3 SILL 10 PSF 2-5/8" 3/8" D.L.O O.D. W.D. 4 JAMB D.L.O W.D. ADME050 W.D. TYPICAL ELEVATION Log onto www.kawneer.com for other configurations D.L.O 2 HORIZONTAL D.L.O D.L.O 4 1-13/16" W.D. 3/8" 3-1/2" 2 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 2-7/16" SINGLE HUNG WINDOW 3-11/16" O.D. 3/8" 5 JAMB kawneer.com © Kawneer Company, Inc., 2014 D.L.O 1 4-1/4" 5 O.D. 1 HEAD O.D. AATM3350 IsoPortTM Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 3-1/2" 8 JULY, 2014 EC 97911-063 SCALE : 3" = 1'-0" AATM3350 IsoPortTM SINGLE HUNG WINDOW Commercial Window, Class CW-PG50-H 3 3/8" kawneer.com 3/8" 3-1/2" © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 2-5/8" D.L.O 4 JAMB D.L.O W.D. W.D. O.D. O.D. 5 JAMB ADME050 D.L.O 2 3 TYPICAL ELEVATION Log onto www.kawneer.com for other configurations 3 SILL 15 PSF 3-11/16" 3/8" D.L.O 1-13/16" 3/8" 1 5-1/4" W.D. 2 HORIZONTAL 2-7/16" 4 W.D. 1 HEAD O.D. EC 97911-063 O.D. D.L.O 5 D.L.O Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 AATM3350 IsoPortTM Window SINGLE HUNG WINDOW SCALE : 3" = 1'-0" AATM3350 IsoPortTM SINGLE HUNG WINDOW Architectural Window, Class AW-PG50-H Class AW-PG70-H (Optional) 3-1/2" 9 AATM3350 IsoPortTM Window EC 97911-063 A class 5 adjustable spring balance with excellent operating forces capable of balancing heavier sash weights. The balance utilizes stainless steel components and is cycle tested for longevity. ZINC SWEEP LOCK AND KEEPER Zinc die cast sweep locks and keepers with a durable black powder coat finish and cycle tested for longevity. Includes a push button lock feature providing added security. AUTO LOCK An optional black rigid PVC spring operated auto lock conveniently located under the sash lift handle. The lock automatically engages the integral sill keeper upon closing the sash. COVERED WEEPS A polycarbonate weep with an integral hinged cover to allow maximum drainage of infiltrating water with a positive closing cover to block drafts and insects. The weep is available in black, white and silver finishes. SASH CAMS Adjustable glass filled nylon cams located left and right on the sash ensure proper alignment and smooth operation. SASH STOPS Black PVC sash stops are inserted into the vertical jambs without exposed fasteners to prevent excessive sash travel. WEATHERING BLOCK Weathering blocks located left and right at the meeting rails significantly improve resistance to air and water infiltration. ADME050 kawneer.com © Kawneer Company, Inc., 2014 HEAVY DUTY BALANCES Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. SINGLE HUNG WINDOW JULY, 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 10 AATM3350 IsoPortTM Window JULY, 2014 EC 97911-063 DOUBLE HUNG WINDOW Standard Features • • • • • Screw and Spline Frame and Sash Corner Joinery Factory Silicone Glazed Interior Applied Glazing Bead Architectural Anodized Finishes and Applied Coatings Two Year Manufacturer's Warranty Thermal Break © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. • High Performance Commercial Window • IsoPortTM Thermal Break Exterior Double Hung Window For specific product applications, Consult your Kawneer representative. kawneer.com ADME050 Interior 11 AATM3350 IsoPortTM Window JULY, 2014 EC 97911-063 CLASS CW-PG50-H / AW-PG50-H OPTIONAL CLASS and GRADE CLASS AW-PG70-H (MAXIMUM SIZE 52" x 99") TESTING STANDARD AAMA / WDMA / CSA / 101 / I.S.2 / A440-08 (NAFS-08) FRAME DEPTH 3-1/2" Overall Frame Depth TYPICAL WALL THICKNESS .070" Nominal TYPICAL MAXIMUM SIZE 60" x 99" (AW), 56" x 91" (CW) TYPICAL MINIMUM SIZE 20" x 34" (10 PSF Sill), 20" x 35" (15 PSF Sill) TYPICAL CONFIGURATIONS STANDARD INFILL OPTIONS 1" STANDARD HARDWARE Heavy Duty Balances Zinc Die Cast Sweep Locks Sash Stops Upper Sash Auto Lock OPTIONAL HARDWARE Sill Auto Lock OTHER OPTIONS Between the Glass Muntin Grids Exterior Applied Muntin Grids Perimeters and Sills Exterior Pannings and Interior Trims Structural Mullions Vertically or Horizontally Stacked Strap Anchors Sill for 10 PSF or 15 PSF Water Performance Insect Screens Nailing Fin Flange DOUBLE HUNG WINDOW PRODUCT PERFORMANCE Air Infiltration NAFS-08 Water Resistance NAFS-08 Design Load NAFS-08 Thermal Transmittance AAMA 507 NFRC 100 Condensation Resistance* AAMA 1503 ≤ 0.30 Cfm/ft2 CW - 10 PSF AW - 15 PSF 50 PSF 70 PSF "U" Factor 0.39 to 0.57 CRF frame - 57 CRF glass - 60 Condensation Sound Temperature Transmittance** Index* ASTM E 1425 CSA A440.2 ASTM E 1332 I frame - 33 I glass - 60 STC - 34 OITC - 29 Note:"U" Values based on computer simulations utilizing Insulating Glass, Low E Coatings and Warm Edge Spacers. See Thermal Charts for various glass types. * CRF and Temperature index based on high performance Low E Glass and Warm Edge Spacers. ** Acoustical test based on laminated glass. ADME050 kawneer.com © Kawneer Company, Inc., 2014 CLASS and GRADE Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. DOUBLE HUNG WINDOW Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 12 © Kawneer Company, Inc., 2014 3/8" Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 3-11/16" 3/8" kawneer.com D.L.O D.L.O 2 2 HORIZONTAL 5 TYPICAL ELEVATION Log onto www.kawneer.com for other configurations D.L.O W.D. W.D. O.D. O.D. 4 JAMB 5 JAMB ADME050 3 SILL 10 PSF 3-11/16" 3/8" D.L.O 2-7/16" 3/8" AATM3350 IsoPortTM DOUBLE HUNG WINDOW Commercial Window, Class CW-PG50-H 3-11/16" O.D. 4 W.D. 1 HEAD O.D. D.L.O 1 W.D. EC 97911-063 4-1/4" 3 D.L.O Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 AATM3350 IsoPortTM Window DOUBLE HUNG WINDOW SCALE : 3" = 1'-0" 3-1/2" 13 3/8" 3-11/16" 4 JAMB D.L.O D.L.O D.L.O W.D. D.L.O W.D. O.D. O.D. ADME050 2 HORIZONTAL TYPICAL ELEVATION Log onto www.kawneer.com for other configurations 3 SILL 15 PSF 5 3-11/16" Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 2-7/16" 3/8" DOUBLE HUNG WINDOW 3-11/16" 3/8" 5 JAMB kawneer.com © Kawneer Company, Inc., 2014 D.L.O 2 O.D. 4 W.D. 1 HEAD O.D. AATM3350 IsoPortTM DOUBLE HUNG WINDOW Architectural Window, Class AW-PG50-H Class AW-PG70-H (Optional) 5-1/4" 3 D.L.O 1 W.D. AATM3350 IsoPortTM Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 3/8" 14 JULY, 2014 EC 97911-063 SCALE : 3" = 1'-0" 3-1/2" JULY, 2014 AATM3350 IsoPortTM Window © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-063 15 DOUBLE HUNG WINDOW HEAVY DUTY BALANCES A class 5 adjustable spring balance with excellent operating forces capable of balancing heavier sash weights. The balance utilizes stainless steel components and is cycle tested for longevity. ZINC SWEEP LOCK AND KEEPER Zinc die cast sweep locks and keepers with a durable black powder coat finish and cycle tested for longevity. Includes a push button lock feature providing added security. AUTO LOCK AND KEEPER A black rigid PVC spring operated auto lock located on the upper sash. The lock automatically engages the head keeper securing the upper sash in the closed position. The auto lock is an option for the lower sash. COVERED WEEPS A polycarbonate weep with an integral hinged cover to allow maximum drainage of infiltrating water with a positive closing cover to block drafts and insects. The weep is available in black, white and silver finishes. SASH CAMS Adjustable glass filled nylon cams located left and right on the sash ensure proper alignment and smooth operation. SASH STOPS Black PVC sash stops are inserted into the vertical jambs without exposed fasteners to prevent excessive sash travel. WEATHERING BLOCK Weathering blocks located left and right at the meeting rails significantly improve resistance to air and water infiltration. kawneer.com ADME050 AATM3350 IsoPortTM Window JULY, 2014 HORIZONTAL SLIDER EC 97911-063 Standard Features Horizontal Sliding Window For specific product applications, Consult your Kawneer representative. ADME050 kawneer.com © Kawneer Company, Inc., 2014 Thermal Break Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Screw and Spline Frame and Sash Corner Joinery Factory Silicone Glazed Interior Applied Glazing Bead with Bulb Gasket Architectural Anodized Finishes and Applied Coatings Two Year Manufacturer's Warranty Interior • • • • • Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. • High Performance Window • IsoPortTM Thermal Break Exterior 16 AATM3350 IsoPortTM Window JULY, 2014 HORIZONTAL SLIDER CLASS and GRADE Class CW-PG50-HS / AW-PG50-HS OPTIONAL CLASS and GRADE Class AW-PG70-HS (Max Size: 99" x 71" OX) TESTING STANDARD AAMA / WDMA / CSA 101 / I.S. 2 / A440-08 (NAFS-08) FRAME DEPTH 3-1/2" Overall Frame Depth TYPICAL WALL THICKNESS .070" Nominal TYPICAL MAXIMUM SIZE 99" x 79" (OX,XO,XX) 148-1/2" x 79" (OXO,XOX) TYPICAL MINIMUM SIZE 32" x 20" (OX,XO,XX) 48" x 20" (OXO,XOX) TYPICAL CONFIGURATIONS STANDARD INFILL OPTIONS1" STANDARD HARDWARE Composite Adjustable Tandem Roller Zinc Die Cast Sweep Lock OPTIONAL HARDWARE PVC Auto Lock OTHER OPTIONS Between the Glass Muntin Grids Exterior Applied Muntin Grids Perimeters and Sills Exterior Pannings and Interior Trims Structural Mullions Vertically or Horizontally Stacked Sill for 10 PSF or 15 PSF Water Performance Insect Screens HORIZONTAL SLIDER WINDOW PRODUCT PERFORMANCE © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-063 17 Air Infiltration NAFS-08 Water Resistance NAFS-08 Design Load NAFS-08 Thermal Transmittance AAMA 507 NFRC 100 Condensation Resistance* AAMA 1503 Condensation Temperature Index* CSA A440.2 Sound Transmittance** ASTM E 1425 ASTM E 1332 ≤ 0.30 Cfm/ft2 CW - 10 PSF AW - 15 PSF 50 PSF 70 PSF "U" Factor 0.37 to 0.54 CRF frame - 66 CRF glass - 66 I frame - 45 I glass - 62 STC - 37 OITC - 29 Note:"U" Values based on computer simulations utilizing Insulating Glass, Low E Coatings and Warm Edge Spacers. See Thermal Charts for various glass types. * CRF and Temperature index based on high performance Low E Glass and Warm Edge Spacers. ** Acoustical test based on laminated glass. kawneer.com ADME050 3/8" 3/8" 2 4 TYPICAL ELEVATION Log onto www.kawneer.com for other configurations 2-5/8" D.L.O 5 FIXED SASH JAMB D.L.O W.D. 2-7/16" O.D. 6 INTERLOCK ADME050 2-5/8" 3/8" 3-1/2" 3 HEAD WITH OPERABLE SASH 7 2 SILL WITH FIXED SASH (10 PSF) 4 SILL WITH OPERABLE SASH (10 PSF) D.L.O D.L.O W.D. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 3-11/16" W.D. HORIZONTAL SLIDER 3-11/16" O.D. 3/8" 7 OPERABLE SASH JAMB kawneer.com © Kawneer Company, Inc., 2014 6 D.L.O 1 HEAD WITH FIXED SASH 6-1/8" 5 D.L.O 3 W.D. 1 O.D. AATM3350 IsoPortTM OX HORIZONTAL SLIDER Commercial Window, Class CW-PG50-HS 5-1/16" O.D. AATM3350 IsoPortTM Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 3-15/32" 18 JULY, 2014 EC 97911-063 SCALE : 3" = 1'-0" AATM3350 IsoPortTM Window JULY, 2014 EC 97911-063 HORIZONTAL SLIDER 5 6 3-11/16" 2-5/8" O.D. 3 HEAD WITH OPERABLE SASH D.L.O 1 HEAD WITH FIXED SASH 7 4 4 SILL WITH OPERABLE SASH (15 PSF) D.L.O 2 SILL WITH FIXED SASH (15 PSF) 7-1/8" 3/8" 6-1/16" TYPICAL ELEVATION Log onto www.kawneer.com for other configurations W.D. 2 3-15/32" © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. W.D. 3 1 3-1/2" 3/8" AATM3350 IsoPortTM OX HORIZONTAL SLIDER Architectural Window, Class AW-PG50-HS Class AW-PG70-HS (Optional) O.D. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. SCALE : 3" = 1'-0" D.L.O 2-5/8" 3/8" D.L.O 2-7/16" O.D. 5 FIXED SASH JAMB kawneer.com D.L.O D.L.O 3-11/16" W.D. W.D. O.D. 6 INTERLOCK ADME050 7 OPERABLE SASH JAMB 3/8" 19 AATM3350 IsoPortTM Window EC 97911-063 Glass filled nylon housing, die cast zamak roller support, precision sealed ball bearing rollers with nylon tires. PVC AUTO LOCK AND KEEPER A black rigid PVC, spring operated auto lock, located on the jamb. The lock automatically engages the jamb keeper securing the sash in the closed position. The auto lock is standard for the exterior sash of the XX configuration only. COVERED WEEP A polycarbonate weep with an integral hinged cover to allow maximum drainage of infiltrating water with a positive closing cover to block drafts and insects. The weep is available in black, white and silver finishes. ZINC SWEEP LOCK AND KEEPER Zinc die cast sweep locks and keepers with a durable black powder coat finish and cycle tested for longevity. Includes a push button lock feature providing added security. SASH STOPS Black PVC sash stops are inserted into the head without exposed fasteners to prevent excessive sash travel. ADME050 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. COMPOSITE ADJUSTABLE TANDEM ROLLER kawneer.com © Kawneer Company, Inc., 2014 HORIZONTAL SLIDER JULY, 2014 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 20 AATM3350 IsoPortTM Window JULY, 2014 EC 97911-063 21 WIND LOAD CHARTS WIND LOAD CHARTS: THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 psi (104 MPa). If the design wind load is determined through the analytical procedures of ASCE/SEI 7-10 or earlier editions, the load shall be based on the nominal loads used in allowable stress design. A 4/3 increase in allowable stress has not been used to develop these curves. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. A = 40 PSF (1915) B = 50 PSF (2394) C = 60 PSF (2873) D = 70 PSF (3352) E = 80 PSF (3830) HORIZONTAL WIDTH IN METERS 1.0 SINGLE HUNG INTERMEDIATE CW-RATED 4 3 A 2 B C D E 1 0 0 1 2 3 4 1.0 SASH HEIGHT IN METERS SASH HEIGHT IN FEET 5 5 HORIZONTAL WIDTH IN METERS 1.0 SINGLE HUNG INTERMEDIATE AW-RATED 4 A 1.0 3 B C D E 2 1 0 0 1 2 3 4 SASH HEIGHT IN METERS SASH HEIGHT IN FEET 5 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. HORIZONTAL WIDTH IN FEET 5 HORIZONTAL WIDTH IN FEET kawneer.com ADME050 AATM3350 IsoPortTM Window 22 JULY, 2014 WIND LOAD CHARTS EC 97911-063 WIND LOAD CHARTS: THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 psi (104 MPa). If the design wind load is determined through the analytical procedures of ASCE/SEI 7-10 or earlier editions, the load shall be based on the nominal loads used in allowable stress design. A 4/3 increase in allowable stress has not been used to develop these curves. MUNTIN CENTERS IN METERS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. A = 40 PSF (1915) B = 50 PSF (2394) C = 60 PSF (2873) D = 70 PSF (3352) E = 80 PSF (3830) 1.0 8 TRUE MUNTIN FOR FIXED WINDOW MUNTIN HEIGHT IN FEET 2.0 6 5 4 A B 1.0 C D E 3 2 1 1 2 3 4 MUNTIN HEIGHT IN METERS 7 5 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. WITH HORIZONTALS MUNTIN CENTERS IN METERS 1.0 8 MUNTIN HEIGHT IN FEET 7 2.0 6 A B C D E 5 4 1.0 3 MUNTIN HEIGHT IN METERS TRUE MUNTIN FOR FIXED WINDOW 2 1 1 2 3 4 5 MUNTIN CENTERS IN FEET WITHOUT HORIZONTALS ADME050 kawneer.com © Kawneer Company, Inc., 2014 MUNTIN CENTERS IN FEET AATM3350 IsoPortTM Window JULY, 2014 EC 97911-063 23 WIND LOAD CHARTS WIND LOAD CHARTS: THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 psi (104 MPa). If the design wind load is determined through the analytical procedures of ASCE/SEI 7-10 or earlier editions, the load shall be based on the nominal loads used in allowable stress design. A 4/3 increase in allowable stress has not been used to develop these curves. MULLION CENTERS IN METERS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1.0 9 SHALLOW THREE PIECE MULLION MULLION HEIGHT IN FEET B 7 C 6 2.0 D 5 4 1.0 3 2 0 1 2 3 4 MULLION HEIGHT IN METERS A 8 A = 30 PSF (1436) B = 40 PSF (1915) C = 50 PSF (2394) D = 60 PSF (2873) 5 MULLION CENTERS IN FEET 1.0 10 3.0 DEEP THREE PIECE MULLION 8 7 2.0 6 A B C D E 5 4 A = 40 PSF (1915) B = 50 PSF (2394) C = 60 PSF (2873) D = 70 PSF (3352) E = 80 PSF (3830) 1.0 3 2 MULLION HEIGHT IN METERS MULLION HEIGHT IN FEET 9 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. MULLION CENTERS IN METERS 0 1 2 3 4 5 MULLION CENTERS IN FEET kawneer.com ADME050 AATM3350 IsoPortTM Window 24 JULY, 2014 WIND LOAD CHARTS EC 97911-063 WIND LOAD CHARTS: THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 psi (104 MPa). If the design wind load is determined through the analytical procedures of ASCE/SEI 7-10 or earlier editions, the load shall be based on the nominal loads used in allowable stress design. A 4/3 increase in allowable stress has not been used to develop these curves. MUNTIN CENTERS IN METERS 2.0 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1.0 9 8 MUNTIN HEIGHT IN FEET 7 2.0 6 5 4 A 1.0 3 MUNTIN HEIGHT IN METERS VERTICAL STACK JAMBS FIXED / FIXED B 2 CD E A = 20 PSF (958) B = 35 PSF (1676) C = 50 PSF (2394) D = 65 PSF (3112) E = 80 PSF (3830) 1 1 2 3 4 5 6 7 8 9 MUNTIN CENTERS IN FEET MUNTIN CENTERS IN METERS 2.0 1.0 9 8 MUNTIN HEIGHT IN FEET 7 2.0 6 5 A 4 1.0 B C DE 3 2 1 1 2 3 4 5 6 7 8 MUNTIN HEIGHT IN METERS VERTICAL STACK JAMBS FIXED / DOUBLE HUNG A = 20 PSF (958) B = 35 PSF (1676) C = 50 PSF (2394) D = 65 PSF (3112) E = 80 PSF (3830) 9 MUNTIN CENTERS IN FEET WITH HORIZONTALS ADME050 kawneer.com © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. WITH HORIZONTALS AATM3350 IsoPortTM Window JULY, 2014 EC 97911-063 25 WIND LOAD CHARTS WIND LOAD CHARTS: THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 psi (104 MPa). If the design wind load is determined through the analytical procedures of ASCE/SEI 7-10 or earlier editions, the load shall be based on the nominal loads used in allowable stress design. A 4/3 increase in allowable stress has not been used to develop these curves. 2.0 1.0 9 VERTICAL STACK JAMBS FIXED / SINGLE HUNG 7 2.0 6 5 4 A 1.0 3 MUNTIN HEIGHT IN METERS 8 MUNTIN HEIGHT IN FEET Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. MUNTIN CENTERS IN METERS B 2 1 CD E 1 2 3 4 5 6 7 8 A = 20 PSF (958) B = 35 PSF (1676) C = 50 PSF (2394) D = 65 PSF (3112) E = 80 PSF (3830) 9 MUNTIN CENTERS IN FEET MUNTIN CENTERS IN METERS 1.0 2.0 9 8 MUNTIN HEIGHT IN FEET 2.0 6 5 4 A 1.0 3 B 2 CD E 1 1 2 3 4 5 6 7 8 9 MUNTIN CENTERS IN FEET WITH HORIZONTALS kawneer.com ADME050 MUNTIN HEIGHT IN METERS VERTICAL STACK JAMBS DOUBLE HUNG / DOUBLE HUNG 7 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. WITH HORIZONTALS A = 20 PSF (958) B = 35 PSF (1676) C = 50 PSF (2394) D = 65 PSF (3112) E = 80 PSF (3830) AATM3350 IsoPortTM Window 26 JULY, 2014 WIND LOAD CHARTS EC 97911-063 WIND LOAD CHARTS: THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 psi (104 MPa). If the design wind load is determined through the analytical procedures of ASCE/SEI 7-10 or earlier editions, the load shall be based on the nominal loads used in allowable stress design. A 4/3 increase in allowable stress has not been used to develop these curves. MUNTIN CENTERS IN METERS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 2.0 1.0 9 VERTICAL STACK JAMBS SINGLE HUNG / SINGLE HUNG 2.0 6 5 A 4 1.0 3 B CD E 2 1 2 3 4 5 6 7 8 9 MUNTIN CENTERS IN FEET WITH HORIZONTALS ADME050 kawneer.com © Kawneer Company, Inc., 2014 1 A = 20 PSF (958) B = 35 PSF (1676) C = 50 PSF (2394) D = 65 PSF (3112) E = 80 PSF (3830) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. MUNTIN HEIGHT IN FEET 7 MUNTIN HEIGHT IN METERS 8 AATM3350 IsoPortTM Window JULY, 2014 EC 97911-063 27 WIND LOAD CHARTS WIND LOAD CHARTS: THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 psi (104 MPa). If the design wind load is determined through the analytical procedures of ASCE/SEI 7-10 or earlier editions, the load shall be based on the nominal loads used in allowable stress design. A 4/3 increase in allowable stress has not been used to develop these curves. 1.0 2.0 9 LOCK STILE HORIZONTAL SLIDER 7 2.0 6 A 5 B C D E 4 SASH HEIGHT IN METERS 8 SASH HEIGHT IN FEET Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. MODULE CENTERS IN METERS 1.0 3 2 1 1 2 MODULE CENTERS IN FEET 5 3 6 7 4 WITHOUT HORIZONTALS 8 A = 40 PSF (1915) B = 50 PSF (2394) C = 60 PSF (2873) D = 70 PSF (3352) E = 80 PSF (3830) 9 1.0 2.0 9 A LOCK STILE HORIZONTAL SLIDER 7 B 6 C D E 5 4 1.0 3 2 1 1 2 3 4 5 6 7 MODULE CENTERS IN FEET 8 9 WITHOUT HORIZONTALS kawneer.com 2.0 ADME050 SASH HEIGHT IN METERS SASH HEIGHT IN FEET 8 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. MODULE CENTERS IN METERS AATM3350 IsoPortTM Window 28 JULY, 2014 EC 97911-063 WIND LOAD CHARTS WIND LOAD CHARTS: THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 psi (104 MPa). If the design wind load is determined through the analytical procedures of ASCE/SEI 7-10 or earlier editions, the load shall be based on the nominal loads used in allowable stress design. A 4/3 increase in allowable stress has not been used to develop these curves. MODULE CENTERS IN METERS 2.0 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 9 A 7 2.0 6 B 5 C 4 D E 1.0 3 WINDOW HEIGHT IN METERS WINDOW HEIGHT IN FEET 8 VERTICAL STACK JAMBS HORIZONTAL SLIDER 2 1 2 3 4 5 6 7 8 9 MODULE CENTERS IN FEET A = 20 PSF (958) B = 35 PSF (1676) C = 50 PSF (2394) D = 65 PSF (3112) E = 80 PSF (3830) WITHOUT HORIZONTALS Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 1 MODULE CENTERS IN METERS 1.0 2.0 9 A 7 2.0 6 B 5 C 4 D E 1.0 3 WINDOW HEIGHT IN METERS WINDOW HEIGHT IN FEET 8 "XX" VERTICAL STACK JAMBS HORIZONTAL SLIDER 2 1 1 2 3 4 5 6 7 8 9 MODULE CENTERS IN FEET WITHOUT HORIZONTALS ADME050 kawneer.com © Kawneer Company, Inc., 2014 1.0 AATM3350 IsoPortTM Window JULY, 2014 EC 97911-063 29 DEADLOAD CHARTS DEADLOAD CHARTS: Horizontal deadload limitations are based upon 1/8" (3.2) maximum allowable deflection at the center of an intermediate horizontal member. The accompanying charts are calculated for the glass types indicated supported on two setting blocks at eight point loading but no more than 6" from the edge of glass. HORIZONTAL WIDTH IN METERS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1.0 8 SINGLE HUNG OR DOUBLE HUNG HORIZONTAL 7 GLAZING HEIGHT IN FEET 5 4 1.0 3 A 2 B C GLAZING HEIGHT IN METERS 2.0 6 GLASS TYPE: A = 1/8" - 3/4" A.S. - 1/8" B = 3/16" - 5/8" A.S. - 3/16" C = 1/4" - 1/2" A.S. - 1/4" 1 0 0 1 2 3 4 5 6 HORIZONTAL WIDTH IN METERS 1.0 8 TRUE HORIZONTAL MUNTIN FOR FIXED WINDOW 7 6 5 4 3 A 2 B C 1.0 GLAZING HEIGHT IN METERS GLAZING HEIGHT IN FEET 2.0 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. HORIZONTAL WIDTH IN FEET 1 0 0 1 2 3 4 5 6 HORIZONTAL WIDTH IN FEET kawneer.com ADME050 GLASS TYPE: A = 1/8" - 3/4" A.S. - 1/8" B = 3/16" - 5/8" A.S. - 3/16" C = 1/4" - 1/2" A.S. - 1/4" AATM3350 IsoPortTM Window 30 JULY, 2014 EC 97911-063 RECEPTORS, SUB SILLS AND ANCHORING SCALE : 3" = 1'-0" TYPICAL RECEPTOR SYSTEM 325059 4-1/4" 335225 JAMB RECEPTOR (Interior Installation) 4-3/8" 335225 1-13/16" FULL DEPTH SILL 1-5/16" 5/8" 335226 ANCHORING 335400 335400 260100 3-1/2" 246500 246501 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. STRAP ANCHOR WITH HUNG WINDOW STRAP ANCHOR WITH FIXED WINDOW 335306 260475 UNEQUAL LEG SILL INTERIOR SNAP TRIM ANCHORING FLANGE / NAILING FIN 335471 335400 335472 STRAP ANCHOR WITH HORIZONTAL SLIDER PVC PERIMETER (Head and Jamb of XX Slider and Female Stack Jambs of Double Hung similar) ADME050 PVC PERIMETER (Typical at Head and Jamb of XO/OX/XOX/OXO Slider and Female Stack Jambs of Single Hung similar) kawneer.com © Kawneer Company, Inc., 2014 325059 HEAD RECEPTOR (Interior Installation) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 1-5/16" 4-1/4" AATM3350 IsoPortTM Window JULY, 2014 EC 97911-063 31 FIXED WINDOW THERMAL CHARTS Project Specific U-Factor Example Calculation 56-3/8" (1432) Example Glass U-Factor = 0.42 Btu/hr • ft2 • °F 5'-0" (1524) Total Daylight Opening = 32-3/8" • 56-3/8" = 12.67ft2 Total Projected Area = 3'-0" • 5'-0" = 15 ft2 0.90 (5.00) 0.85 Percent of Glass = (Total Daylight Opening ÷ Total Projected Area)100 = (12.67 ÷ 15)100 = 85% 0.80 32-3/8" (822) (4.50) 0.75 System U-factor vs Percent of Glass Area 0.70 (4.00) 0.65 0.60 0.46 (2.61) 0.44 (2.50) 0.42 (2.39) 0.40 (2.27) 0.38 (2.16) 0.36 (2.05) 0.34 (1.93) © Kawneer Company, Inc., 2014 0.32 (1.82) 0.50 0.44 Btu hr • ft2 • °F System U-factor 0.48 (2.73) 0.55 E IGN PL S M E A D EX OR F T O Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. N COG U-factor (3.50) (3.00) 0.45 (2.50) 0.40 0.35 0.30 (1.71) (2.00) 0.28 (1.59) 0.30 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.25 0.20 (1.14) 0.20 0.85 Percent of Glass Area Based on 85% glass and center of glass (COG) U-factor of 0.42 System U-factor is equal to 0.44 Btu/hr • ft2 • °F kawneer.com ADME050 (1.50) W m2 • °C System U-factor Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 3'-0" (915) AATM3350 IsoPortTM Window 32 JULY, 2014 EC 97911-063 FIXED WINDOW THERMAL CHARTS AATM3350 IsoPortTM FIXED WINDOW Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-factor vs Percent of Glass Area 0.90 (5.00) 0.85 0.80 (4.50) 0.75 0.70 (4.00) 0.55 COG U-factor 0.50 0.48 (2.73) (3.00) 0.46 (2.61) 0.44 (2.50) 0.45 0.42 (2.39) (2.50) 0.40 (2.27) 0.38 (2.16) 0.40 0.36 (2.05) 0.34 (1.93) 0.32 (1.82) 0.35 0.30 (1.71) (2.00) 0.28 (1.59) 0.30 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.25 0.20 (1.14) (1.50) 0.20 Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. ADME050 kawneer.com © Kawneer Company, Inc., 2014 (3.50) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Btu hr • ft2 • °F System U-factor 0.60 W m2 • °C System U-factor 0.65 System VT © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 kawneer.com AATM3350 IsoPortTM Window EC 97911-063 FIXED WINDOW THERMAL CHARTS AATM3350 IsoPortTM FIXED WINDOW System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME050 33 34 AATM3350 IsoPortTM Window JULY, 2014 EC 97911-063 FIXED WINDOW THERMAL PERFORMANCE MATRIX (NFRC SIZE) AATM3350 IsoPortTM FIXED WINDOW Thermal Transmittance1 (BTU/hr • ft 2 • °F) Overall U-Factor 4 0.48 0.56 0.46 0.54 0.44 0.52 0.42 0.51 0.40 0.49 0.38 0.48 0.36 0.46 0.34 0.44 0.32 0.43 0.30 0.41 0.28 0.40 0.26 0.38 0.24 0.36 0.22 0.35 0.20 0.33 Glass SHGC 3 Overall Glass U-Factor 4 Glass VT 3 Overall VT 4 0.75 0.65 0.75 0.64 0.70 0.61 0.70 0.60 0.65 0.57 0.65 0.56 0.60 0.53 0.60 0.51 0.55 0.48 0.55 0.47 0.50 0.44 0.50 0.43 0.45 0.40 0.45 0.39 0.40 0.35 0.40 0.34 0.35 0.31 0.35 0.30 0.30 0.27 0.30 0.26 0.25 0.23 0.25 0.21 0.20 0.18 0.20 0.17 0.15 0.14 0.15 0.13 0.10 0.10 0.10 0.09 0.05 0.05 0.05 0.04 NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC 100. 2. SHGC and VT values are determined in accordance with NFRC 200. 3. Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1200mm wide by 1500mm high (47-1/4" by 59-1/16"). ADME050 kawneer.com © Kawneer Company, Inc., 2014 Visible Transmittance 2 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. SHGC Matrix 2 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Glass U-Factor 3 AATM3350 IsoPortTM Window JULY, 2014 EC 97911-063 35 SINGLE HUNG THERMAL CHARTS Generic Project Specific U-factor Example Calculation (Percent of Glass will vary on specific products depending on sitelines) 3'-0" (915) 25-3/4" (654) 5'-0" (1524) 25-3/4" (654) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 30-3/4" (781) 28-5/8" (727) Example Glass U-Factor = 0.42 Btu/hr • ft2 • °F Total Daylight Opening = (30-3/4" • 25-3/4") + (28-5/8" • 25-3/4") = 10.62 ft2 Total Projected Area = 3'-0" • 5'-0" = 15 ft2 Percent of Glass = (Total Daylight Opening ÷ Total Projected Area)100 = (10.62 ÷ 15)100 = 71% System U-factor vs Percent of Glass Area (5.00) 0.85 0.80 © Kawneer Company, Inc., 2014 (2.73) (2.61) (2.50) (2.39) (2.27) (2.16) (2.05) (1.93) (1.82) (1.71) (1.59) (1.48) (1.37) (1.25) (1.14) 0.65 0.60 0.55 0.50 0.51 0.45 (4.00) (3.50) (3.00) (2.50) 0.40 0.35 (2.00) 0.30 0.25 0.20 70 71% 75 65 60 55 Percent of Glass Area Based on 71% glass and center of glass (COG) U-factor of 0.42 System U-factor is equal to 0.51 Btu/hr • ft2 • °F kawneer.com Btu hr • ft2 • °F System U-factor E IGN PL S M E A D EX OR F T O COG U-factor 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 0.28 0.26 0.24 0.22 0.20 0.70 ADME050 50 (1.50) W m2 • °C System U-factor (4.50) 0.75 N Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.90 36 AATM3350 IsoPortTM Window JULY, 2014 EC 97911-063 SINGLE HUNG THERMAL CHARTS AATM3350 IsoPortTM SINGLE HUNG WINDOW Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. ADME050 kawneer.com © Kawneer Company, Inc., 2014 COG U-factor Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Btu hr • ft2 • °F System U-factor System U-factor vs Percent of Glass Area System VT © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 kawneer.com AATM3350 IsoPortTM Window EC 97911-063 Vision Area / Total Area (%) ADME050 37 SINGLE HUNG THERMAL CHARTS AATM3350 IsoPortTM SINGLE HUNG WINDOW System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT With Warm Edge Spacer With Aluminum Spacer AATM3350 IsoPortTM SINGLE HUNG WINDOW Thermal Transmittance1 (BTU/hr • ft 2 • °F) Glass U-Factor 3 Overall U-Factor 4 0.48 0.57 0.46 0.55 0.44 0.54 0.42 0.53 0.40 0.51 0.38 0.50 0.36 0.49 0.34 0.47 0.32 0.46 0.30 0.45 0.28 0.43 0.26 0.42 0.24 0.40 0.22 0.39 0.20 0.38 0.38 0.47 0.36 0.45 0.34 0.44 0.32 0.42 0.30 0.41 0.28 0.40 0.26 0.39 0.24 0.37 0.22 0.35 0.20 0.34 ADME050 kawneer.com © Kawneer Company, Inc., 2014 SINGLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. AATM3350 IsoPortTM Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 38 JULY, 2014 EC 97911-063 AATM3350 IsoPortTM Window JULY, 2014 SINGLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) AATM3350 IsoPortTM SINGLE HUNG WINDOW SHGC Matrix 2 Visible Transmittance 2 Glass SHGC 3 Overall Glass U-Factor 4 Glass VT 3 Overall VT 4 0.75 0.57 0.75 0.56 0.70 0.53 0.70 0.52 0.65 0.49 0.65 0.48 0.60 0.46 0.60 0.45 0.55 0.42 0.55 0.41 0.50 0.38 0.50 0.37 0.45 0.34 0.45 0.33 0.40 0.31 0.40 0.30 0.35 0.27 0.35 0.26 0.30 0.23 0.30 0.22 0.25 0.20 0.25 0.19 0.20 0.16 0.20 0.15 0.15 0.12 0.15 0.11 0.10 0.08 0.10 0.07 0.05 0.05 0.05 0.04 NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC 100. 2. SHGC and VT values are determined in accordance with NFRC 200. 3. Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1200mm wide by 1500mm high (47-1/4" by 59-1/16"). © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-063 kawneer.com ADME050 39 AATM3350 IsoPortTM Window 40 JULY, 2014 EC 97911-063 DOUBLE HUNG THERMAL CHARTS Generic Project Specific U-factor Example Calculation (Percent of Glass will vary on specific products depending on sitelines) 3'-0" (915) 24-31/32" (634) 5'-0" (1524) 24-31/32" (634) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 28-5/8" (727) 28-5/8" (727) Example Glass U-Factor = 0.42 Btu/hr • ft2 • °F Total Daylight Opening = (28-5/8" • 24-31/32") + (28-5/8" • 24-31/32") = 9.21 ft2 Total Projected Area = 3'-0" • 5'-0" = 15 ft2 Percent of Glass = (Total Daylight Opening ÷ Total Projected Area)100 = (9.21 ÷ 15)100 = 61% System U-factor vs Percent of Glass Area 0.90 E IGN PL S M E A D EX OR F T O (2.73) (2.61) (2.50) (2.39) (2.27) (2.16) (2.05) (1.93) (1.82) (1.71) (1.59) (1.48) (1.37) (1.25) (1.14) 0.65 0.60 Btu hr • ft2 • °F System U-factor N COG U-factor (4.00) (3.50) 0.550.55 0.50 0.45 (3.00) (2.50) 0.40 0.35 (2.00) 0.30 0.25 (1.50) 0.20 75 70 60 65 Percent of Glass Area 55 50 61% 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 0.28 0.26 0.24 0.22 0.20 0.70 W m2 • °C System U-factor (4.50) 0.75 Based on 61% glass and center of glass (COG) U-factor of 0.42 System U-factor is equal to 0.55 Btu/hr • ft2 • °F ADME050 kawneer.com © Kawneer Company, Inc., 2014 0.80 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. (5.00) 0.85 AATM3350 IsoPortTM Window JULY, 2014 EC 97911-063 DOUBLE HUNG THERMAL CHARTS AATM3350 IsoPortTM DOUBLE HUNG WINDOW Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 Btu hr • ft2 • °F System U-factor System U-factor vs Percent of Glass Area © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. COG U-factor Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. kawneer.com ADME050 41 COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME050 kawneer.com © Kawneer Company, Inc., 2014 DOUBLE HUNG THERMAL CHARTS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System SHGC AATM3350 IsoPortTM Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System VT 42 JULY, 2014 EC 97911-063 AATM3350 IsoPortTM DOUBLE HUNG WINDOW System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area With Warm Edge Spacer © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. With Aluminum Spacer Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 kawneer.com AATM3350 IsoPortTM Window EC 97911-063 DOUBLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) AATM3350 IsoPortTM DOUBLE HUNG WINDOW Thermal Transmittance1 (BTU/hr • ft 2 • °F) Glass U-Factor 3 Overall U-Factor 4 0.48 0.57 0.46 0.56 0.44 0.55 0.42 0.53 0.40 0.52 0.38 0.51 0.36 0.50 0.34 0.48 0.32 0.47 0.30 0.46 0.28 0.44 0.26 0.43 0.24 0.42 0.22 0.41 0.20 0.39 0.38 0.48 0.36 0.46 0.34 0.45 0.32 0.44 0.30 0.42 0.28 0.41 0.26 0.40 0.24 0.38 0.22 0.37 0.20 0.36 ADME050 43 AATM3350 IsoPortTM Window JULY, 2014 EC 97911-063 AATM3350 IsoPortTM DOUBLE HUNG WINDOW Visible Transmittance 2 Glass SHGC 3 Overall Glass U-Factor 4 Glass VT 3 Overall VT 4 0.75 0.54 0.75 0.53 0.70 0.50 0.70 0.49 0.65 0.47 0.65 0.46 0.60 0.43 0.60 0.42 0.55 0.40 0.55 0.39 0.50 0.39 0.50 0.35 0.45 0.33 0.45 0.32 0.40 0.29 0.40 0.28 0.35 0.26 0.35 0.25 0.30 0.22 0.30 0.21 0.25 0.19 0.25 0.18 0.20 0.15 0.20 0.14 0.15 0.12 0.15 0.11 0.10 0.08 0.10 0.07 0.05 0.05 0.05 0.04 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. SHGC Matrix 2 NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC 100. 2. SHGC and VT values are determined in accordance with NFRC 200. 3. Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1200mm wide by 1500mm high (47-1/4" by 59-1/16"). ADME050 kawneer.com © Kawneer Company, Inc., 2014 DOUBLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 44 JULY, 2014 AATM3350 IsoPortTM Window EC 97911-063 OX HORIZONTAL SLIDER THERMAL CHARTS 45 Generic Project Specific U-factor Example Calculation (Percent of Glass will vary on specific products depending on sitelines) 25-5/8" (651) 3'-0" (915) 26-3/16" (665) 28-5/16" (719) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 5'-0" (1524) 25-5/8" (651) Example Glass U-Factor = 0.42 Btu/hr • ft2 • °F Total Daylight Opening = (25-5/8" • 28-5/16") + (25-5/8" • 26-3/16") = 9.70 ft2 Total Projected Area = 3'-0" • 5'-0" = 15 ft2 Percent of Glass = (Total Daylight Opening ÷ Total Projected Area)100 = (9.70 ÷ 15)100 = 65% System U-factor vs Percent of Glass Area (5.00) 0.85 0.80 © Kawneer Company, Inc., 2014 (2.73) (2.61) (2.50) (2.39) (2.27) (2.16) (2.05) (1.93) (1.82) (1.71) (1.59) (1.48) (1.37) (1.25) (1.14) 0.65 0.60 0.55 0.50 0.45 0.35 (3.50) (3.00) (2.50) (2.00) 0.30 0.20 65 65% 70 60 55 Percent of Glass Area Based on 65% glass and center of glass (COG) U-factor of 0.42 System U-factor is equal to 0.53 Btu/hr • ft2 • °F kawneer.com 0.53 (4.00) 0.40 0.25 75 Btu hr • ft2 • °F System U-factor E IGN PL S M E A D EX OR F T O COG U-factor 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 0.28 0.26 0.24 0.22 0.20 0.70 ADME050 50 (1.50) W m2 • °C System U-factor (4.50) 0.75 N Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.90 46 AATM3350 IsoPortTM Window JULY, 2014 OX HORIZONTAL SLIDER THERMAL CHARTS EC 97911-063 AATM3350 IsoPortTM OX HORIZONTAL SLIDER WINDOW Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 System U-factor vs Percent of Glass Area Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. ADME050 kawneer.com © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Btu hr • ft2 • °F System U-factor COG U-factor System VT © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 AATM3350 IsoPortTM Window EC 97911-063 OX HORIZONTAL SLIDER THERMAL CHARTS Vision Area / Total Area (%) kawneer.com ADME050 47 AATM3350 IsoPortTM OX HORIZONTAL SLIDER WINDOW System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT AATM3350 IsoPortTM OX HORIZONTAL SLIDER WINDOW Thermal Transmittance1 (BTU/hr • ft 2 • °F) Glass U-Factor 3 Overall U-Factor 4 0.47 0.54 0.46 0.53 0.44 0.52 0.42 0.50 0.40 0.49 0.38 0.48 0.36 0.47 0.34 0.46 0.32 0.44 0.30 0.43 0.28 0.42 0.26 0.41 0.24 0.39 0.22 0.38 0.20 0.37 0.18 0.35 0.16 0.34 0.14 0.33 0.12 0.32 0.10 0.30 ADME050 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. OX HORIZONTAL SLIDER THERMAL PERFORMANCE MATRIX (NFRC SIZE) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. AATM3350 IsoPortTM Window kawneer.com © Kawneer Company, Inc., 2014 With Aluminum Spacer 48 JULY, 2014 EC 97911-063 AATM3350 IsoPortTM Window JULY, 2014 OX HORIZONTAL SLIDER THERMAL PERFORMANCE MATRIX (NFRC SIZE) AATM3350 IsoPortTM OX HORIZONTAL SLIDER WINDOW SHGC Matrix 2 Visible Transmittance 2 Glass SHGC 3 Overall Glass U-Factor 4 Glass VT 3 Overall VT 4 0.75 0.53 0.75 0.52 0.70 0.50 0.70 0.49 0.65 0.46 0.65 0.45 0.60 0.43 0.60 0.42 0.55 0.39 0.55 0.38 0.50 0.36 0.50 0.35 0.45 0.32 0.45 0.31 0.40 0.29 0.40 0.28 0.35 0.25 0.35 0.24 0.30 0.22 0.30 0.21 0.25 0.18 0.25 0.17 0.20 0.15 0.20 0.14 0.15 0.11 0.15 0.10 0.10 0.08 0.10 0.07 0.05 0.04 0.05 0.03 NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC 100. 2. SHGC and VT values are determined in accordance with NFRC 200. 3. Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1500mm wide by 1200mm high (59-1/16" by 47-1/4"). © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-063 kawneer.com ADME050 49 50 AATM3350 IsoPortTM Window JULY, 2014 XX HORIZONTAL SLIDER THERMAL CHARTS EC 97911-063 AATM3350 IsoPortTM XX HORIZONTAL SLIDER WINDOW Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 System U-factor vs Percent of Glass Area Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. ADME050 kawneer.com © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Btu hr • ft2 • °F System U-factor COG U-factor System VT © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 AATM3350 IsoPortTM Window EC 97911-063 XX HORIZONTAL SLIDER THERMAL CHARTS Vision Area / Total Area (%) kawneer.com ADME050 51 AATM3350 IsoPortTM XX HORIZONTAL SLIDER WINDOW System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT AATM3350 IsoPortTM XX HORIZONTAL SLIDER WINDOW Thermal Transmittance1 (BTU/hr • ft 2 • °F) Glass U-Factor 3 Overall U-Factor 4 0.47 0.56 0.46 0.55 0.44 0.54 0.42 0.52 0.40 0.51 0.38 0.50 0.36 0.49 0.34 0.48 0.32 0.47 0.30 0.45 0.28 0.44 0.26 0.43 0.24 0.42 0.22 0.41 0.20 0.40 0.18 0.38 0.16 0.37 0.14 0.36 0.12 0.35 0.10 0.34 ADME050 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. XX HORIZONTAL SLIDER THERMAL PERFORMANCE MATRIX (NFRC SIZE) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. AATM3350 IsoPortTM Window kawneer.com © Kawneer Company, Inc., 2014 With Aluminum Spacer 52 JULY, 2014 EC 97911-063 AATM3350 IsoPortTM Window JULY, 2014 XX HORIZONTAL SLIDER THERMAL PERFORMANCE MATRIX (NFRC SIZE) AATM3350 IsoPortTM XX HORIZONTAL SLIDER WINDOW SHGC Matrix 2 Visible Transmittance 2 Glass SHGC 3 Overall Glass U-Factor 4 Glass VT 3 Overall VT 4 0.75 0.51 0.75 0.50 0.70 0.47 0.70 0.46 0.65 0.44 0.65 0.43 0.60 0.41 0.60 0.40 0.55 0.37 0.55 0.36 0.50 0.34 0.50 0.33 0.45 0.31 0.45 0.30 0.40 0.28 0.40 0.26 0.35 0.24 0.35 0.23 0.30 0.21 0.30 0.20 0.25 0.18 0.25 0.17 0.20 0.14 0.20 0.13 0.15 0.11 0.15 0.10 0.10 0.08 0.10 0.07 0.05 0.04 0.05 0.03 NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC 100. 2. SHGC and VT values are determined in accordance with NFRC 200. 3. Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1500mm wide by 1200mm high (59-1/16" by 47-1/4"). © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-063 kawneer.com ADME050 53 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. AATM3350 IsoPortTM Window BLANK PAGE ADME050 kawneer.com © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 54 JULY, 2014 EC 97911-063