JULY, 2014 AA™5450 Ultra Thermal Window INDEX FIXED WINDOW................................................................................. 3-6 SINGLE HUNG WINDOW................................................................ 7-13 DOUBLE HUNG WINDOW............................................................ 14-21 HORIZONTAL SLIDING WINDOW................................................ 22-33 WINDLOAD CHARTS......................................................................... 34 RECEPTORS...................................................................................... 35 ANCHORS.......................................................................................... 36 THERMAL CHARTS...................................................................... 37-82 LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR. Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses ( ) are millimeters unless otherwise noted. The following metric (SI) units are found in these details: m –meter cm – centimeter mm –millimeter s –second Pa –pascal MPa –megapascal © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-061 1 Kawneer reserves the right to change configurations without prior notice when deemed necessary for product improvement. kawneer.com ADME120 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. AA™5450 Ultra Thermal Window BLANK PAGE ADME120 kawneer.com © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 2 JULY, 2014 EC 97911-061 AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 FIXED WINDOW Standard Features High Performance Architectural Grade Window Tested to U.S. and Canadian Standards Polyamide Thermal Break Screw and Spline Frame Corner Joinery Factory Silicone Glazed Interior Applied Glazing Bead Architectural Anodized Finishes and Applied Coatings Interior and Exterior Dual Finish Options • Two Year Manufacturer's Warranty © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. • • • • • • • • Exterior Interior Fixed Window For specific product applications, Consult your Kawneer representative. kawneer.com ADME120 Thermal Break 3 AA™5450 Ultra Thermal Window EC 97911-061 CLASS AW-PG70-FW TESTING METHOD AAMA / WDMA / CSA / 101 / I.S.2 / A440 (NAFS) FRAME DEPTH 4-5/8" Overall Frame Depth TYPICAL WALL THICKNESS 0.070" Nominal TYPICAL MAXIMUM WINDOW SIZE 60" X 99" TYPICAL MINIMUM WINDOW SIZE 15" X 15" TYPICAL CONFIGURATIONS STANDARD INFILL OPTIONS 1" and 1-1/2" STANDARD HARDWARE Not Applicable OPTIONAL HARDWARE Not Applicable OTHER OPTIONS Between the Glass Muntins Historic Beveled Exterior Glazed-in Muntins (1-1/2" max. overall thickness) Exterior and Interior Tape Applied Muntins Perimeters and Sills Exterior Pannings and Interior Trims True Intermediate Muntin Structural Mullions H-Mullion for vertical stacking Strap Anchors Male/Female horizontally stacked ADME120 kawneer.com © Kawneer Company, Inc., 2014 CLASS and GRADE Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. FIXED WINDOW JULY, 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 4 3/8" kawneer.com VARIES 2" 4 JAMB D.L.O 3A SILL (Panning Fin) D.L.O 2-5/8" D.L.O 5 VERTICAL ADME120 D.L.O W.D. W.D. O.D. O.D. 6 JAMB 2" D.L.O 2" D.L.O 3 SILL TYPICAL ELEVATION Log onto www.kawneer.com for other configurations D.L.O 2 HORIZONTAL 2-5/8" 6 D.L.O D.L.O W.D. O.D. 2" 1 HEAD W.D. 5 O.D. 1 3/8" 3/8" AA™5450 FIXED WINDOW (1" Double Glazed) W.D. O.D. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 4 4-5/8" 4-5/8" 4-5/8" © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. JULY, 2014 AA™5450 Ultra Thermal Window EC 97911-061 FIXED WINDOW SCALE : 3" = 1'-0" 4-5/8" 3-5/8" 2 3 2" 3/8" 5 3/8" 2" 4 JAMB D.L.O D.L.O D.L.O 2-5/8" D.L.O 5 VERTICAL ADME120 D.L.O W.D. W.D. O.D. O.D. 2" 2 HORIZONTAL 3A SILL (Panning Fin) 2-5/8" 6 D.L.O 3-5/8" 2 D.L.O 2" Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. D.L.O D.L.O O.D. 3/8" AA™5450 FIXED WINDOW (1-1/2" Triple Glazed) W.D. FIXED WINDOW 2" 3/8" 6 JAMB kawneer.com © Kawneer Company, Inc., 2014 3 W.D. 3 SILL O.D. 1 HEAD 2" TYPICAL ELEVATION Log onto www.kawneer.com for other configurations 3/8" 5 W.D. 1 O.D. AA™5450 Ultra Thermal Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. VARIES 4 4-5/8" 4-5/8" 4-5/8" 6 JULY, 2014 EC 97911-061 SCALE : 3" = 1'-0" 4-5/8" AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 SINGLE HUNG WINDOW Standard Features Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. • • • • • • • • High Performance Architectural Grade Window Tested to U.S. and Canadian Standards Polyamide Thermal Break Screw and Spline Frame Corner Joinery Factory Silicone Glazed Interior Applied Glazing Bead Architectural Anodized Finishes and Applied Coatings Interior and Exterior Dual Finish Options • Two Year Manufacturer's Warranty © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Thermal Break Exterior Single Hung Window For specific product applications, Consult your Kawneer representative. kawneer.com ADME120 Interior 7 AA™5450 Ultra Thermal Window EC 97911-061 CLASS AW-PG50-H TESTING METHOD AAMA / WDMA / CSA / 101 / I.S.2 / A440 (NAFS) FRAME DEPTH 4-5/8" Overall Frame Depth TYPICAL WALL THICKNESS 0.070" Nominal TYPICAL MAXIMUM WINDOW SIZE 60" X 99" TYPICAL MINIMUM WINDOW SIZE 24" X 36" TYPICAL CONFIGURATIONS STANDARD INFILL OPTIONS 1" and 1-1/2" STANDARD HARDWARE Heavy Duty Balances White Bronze Sweep Locks Sash Stops OPTIONAL HARDWARE Sill Auto Locks OTHER OPTIONS Between the Glass Muntins Historic Beveled Exterior Glazed-in Muntins (1-1/2" max. overall thickness) Exterior and Interior Tape Applied Muntins Perimeters and Sills Exterior Pannings and Interior Trims True Intermediate Muntin Structural Mullions Male /Female horizontally stacked H-Mullion for vertical stacking Tri-lite Configuration Strap Anchors ADME120 kawneer.com © Kawneer Company, Inc., 2014 CLASS and GRADE Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. SINGLE HUNG WINDOW JULY, 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 8 3/8" 3/8" kawneer.com 2-9/16" D.L.O W.D. D.L.O 3 SILL 10 PSF (Panning Fin) 3-3/4" 2-9/16" W.D. O.D. 4 FIXED JAMB 5 OPERABLE JAMB 3/8" ADME120 3 SILL 15 PSF TYPICAL ELEVATION Log onto www.kawneer.com for other configurations D.L.O 3/8" 3 W.D. W.D. D.L.O D.L.O 2" 2 HORIZONTAL 3-13/16" D.L.O D.L.O 1 3-13/16" 1-11/16" W.D. O.D. 3/8" SCALE : 3" = 1'-0" W.D. 3 SILL 10 PSF O.D. EC 97911-061 4-13/16" O.D. 1 HEAD O.D. 2 VARIES 4-5/8" 4-5/8" Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. AA™5450 SINGLE HUNG WINDOW (1" Double Glazed) O.D. D.L.O © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. JULY, 2014 AA™5450 Ultra Thermal Window SINGLE HUNG WINDOW 4-5/8" 4 5 Note: 15 PSF Sill also available with panning fin. 9 2-9/16" D.L.O O.D. W.D. 4 FIXED JAMB D.L.O W.D. 3/8" 3/8" 2-9/16" 3-3/4" 3/8" ADME120 3 SILL 15 PSF W.D. 3/8" W.D. D.L.O 2" 4 5 O.D. D.L.O D.L.O Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. D.L.O 2 HORIZONTAL 3-13/16" 1-11/16" W.D. 3/8" SINGLE HUNG WINDOW 5 OPERABLE JAMB Note: 15 PSF Sill also available with panning fin. kawneer.com © Kawneer Company, Inc., 2014 TYPICAL ELEVATION Log onto www.kawneer.com for other configurations D.L.O 1 3-13/16" AA™5450 Ultra Thermal Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. D.L.O 3 W.D. 3 SILL 10 PSF (Panning Fin) O.D. SCALE : 3" = 1'-0" 4-13/16" 3 SILL 10 PSF O.D. 1 HEAD O.D. 2 VARIES AA™5450 SINGLE HUNG WINDOW (1-1/2" Triple Glazed) O.D. 4-5/8" 4-5/8" 10 JULY, 2014 EC 97911-061 4-5/8" 3/8" kawneer.com 2-9/16" D.L.O W.D. D.L.O O.D. W.D. O.D. 4 FIXED JAMB 5 OPERABLE JAMB D.L.O TYPICAL ELEVATION Log onto www.kawneer.com for other configurations 3-3/4" 3/8" ADME120 3/8" 3 SILL 10 PSF 3 SILL 15 PSF W.D. 6 D.L.O D.L.O 2 HORIZONTAL 2" D.L.O 2 D.L.O 2-1/2" 2 HORIZONTAL 3-13/16" 3 W.D. D.L.O D.L.O 1-11/16" W.D. 3/8" SCALE : 3" = 1'-0" 4-13/16" 1 O.D. 1 HEAD O.D. AA™5450 SINGLE HUNG WINDOW (Tri-Lite 1" Double Glazed) O.D. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-061 3/8" 4-5/8" 4-5/8" © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. JULY, 2014 AA™5450 Ultra Thermal Window 11 SINGLE HUNG WINDOW 4-5/8" 5 4 Note: 10 PSF Sill also available with panning fin. 2-9/16" Note: 15 PSF Sill also available with panning fin. 3/8" 2-9/16" D.L.O W.D. O.D. 4 FIXED JAMB D.L.O W.D. 3/8" O.D. ADME120 3 SILL 15 PSF D.L.O D.L.O 2 D.L.O 2-1/2" 2 5 HORIZONTAL D.L.O D.L.O Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 2" 1-11/16" 3/8" SINGLE HUNG WINDOW 4 Note: 10 PSF Sill also available with panning fin. 3-3/4" 2-9/16" Note: 15 PSF Sill also available with panning fin. 5 OPERABLE JAMB kawneer.com © Kawneer Company, Inc., 2014 6 D.L.O HORIZONTAL 3-13/16" O.D. W.D. AA™5450 Ultra Thermal Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. D.L.O SILL 10 PSF W.D. 3 O.D. AA™5450 SINGLE HUNG WINDOW (Tri-Lite 1-1/2" Triple Glazed) 4-13/16" TYPICAL ELEVATION Log onto www.kawneer.com for other configurations 3/8" HEAD W.D. 1 O.D. SCALE : 3" = 1'-0" 3/8" 4-5/8" 4-5/8" 12 JULY, 2014 EC 97911-061 4-5/8" JULY, 2014 AA™5450 Ultra Thermal Window © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-061 SINGLE HUNG WINDOW HEAVY DUTY BALANCES A class 5 adjustable spiral balance with excellent operating forces capable of balancing heavier sash weights. The balance utilizes stainless steel components and is cycle tested for longevity. SWEEP LOCK AND KEEPER White Bronze sweep locks and keepers with a durable brushed nickel finish and cycle tested for longevity. AUTO LOCK An optional spring operated auto lock conveniently located under the sash lift handle or an optional white bronze spring operated autolock located on the handle. The lock automatically engages the integral sill keeper upon closing the sash. COVERED WEEPS Weep with an integral hinged cover to allow maximum drainage of infiltrating water with a positive closing cover to block drafts and insects. The weep is available in black and white finishes. SASH CAMS Adjustable glass filled nylon cams located left and right on the sash ensure proper alignment and smooth operation. SASH STOPS Black rigid vinyl sash stops are inserted into the vertical jambs without exposed fasteners to prevent excessive sash travel. kawneer.com ADME120 13 AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 DOUBLE HUNG WINDOW Standard Features High Performance Architectural Grade Window Tested to U.S. and Canadian Standards Polyamide Thermal Break Screw and Spline Frame Corner Joinery Factory Silicone Glazed Interior Applied Glazing Bead Architectural Anodized Finishes and Applied Coatings Interior and Exterior Dual Finish Options Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. • • • • • • • • • Two Year Manufacturer's Warranty Exterior Interior Double Hung Window For specific product applications, Consult your Kawneer representative. ADME120 kawneer.com © Kawneer Company, Inc., 2014 Thermal Break Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 14 JULY, 2014 AA™5450 Ultra Thermal Window DOUBLE HUNG WINDOW CLASS and GRADE CLASS AW-PG50-H TESTING METHOD AAMA / WDMA / CSA / 101 / I.S.2 / A440 (NAFS) FRAME DEPTH 4-5/8" Overall Frame Depth TYPICAL WALL THICKNESS 0.070" Nominal TYPICAL MAXIMUM WINDOW SIZE 60" X 99" TYPICAL MINIMUM WINDOW SIZE 24" X 36" TYPICAL CONFIGURATIONS STANDARD INFILL OPTIONS 1" and 1-1/2" STANDARD HARDWARE Heavy Duty Balances Zinc Die Cast Sweep Locks Sash Stops Aluminum Upper Sash Auto Lock OPTIONAL HARDWARE Aluminum or White Bronze Sill Auto Locks OTHER OPTIONS Between the Glass Muntins Historic Beveled Exterior Glazed-in Muntins (1-1/2" max. overall thickness) Exterior and Interior Tape Applied Muntins Perimeters and Sills Exterior Pannings and Interior Trims True Intermediate Muntin Structural Mullions Male/Female horizontally stacked H-Mullion for vertical stacking Strap Anchors © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-061 kawneer.com ADME120 15 3-3/4" D.L.O D.L.O W.D. W.D. O.D. O.D. 4 JAMB 5 JAMB 3-3/4" 3/8" ADME120 3 SILL 15 PSF TYPICAL ELEVATION Log onto www.kawneer.com for other configurations D.L.O 1-13/16" Note: 15 PSF Sill also available with panning fin. kawneer.com © Kawneer Company, Inc., 2014 D.L.O 2" D.L.O D.L.O 1-3/4" 2-13/16" 3/8" DOUBLE HUNG WINDOW Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. D.L.O 2 3-13/16" 2 HORIZONTAL 3-13/16" O.D. W.D. AA™5450 Ultra Thermal Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. D.L.O 3 SILL 10 PSF (Panning Fin) O.D. 3 SILL 10 PSF W.D. 1 4-13/16" 3 3/8" 5 O.D. 1 HEAD W.D. 4 VARIES AA™5450 DOUBLE HUNG WINDOW (1" Double Glazed) O.D. SCALE : 3" = 1'-0" W.D. 1-13/16" 3/8" 3/8" 4-5/8" 4-5/8" 16 JULY, 2014 EC 97911-061 4-5/8" 3/8" 3/8" kawneer.com 3-3/4" W.D. D.L.O D.L.O W.D. O.D. O.D. 4 FIXED JAMB 5 OPERABLE JAMB TYPICAL ELEVATION Log onto www.kawneer.com for other configurations 3-3/4" 3/8" ADME120 D.L.O D.L.O D.L.O 2 3 SILL 10 PSF (Panning Fin) 3 SILL 15 PSF 3-13/16" 2" 2 HORIZONTAL 3-13/16" 3 SILL 10 PSF W.D. D.L.O D.L.O 1 4-13/16" 5 O.D. O.D. 1-3/4" 2-13/16" W.D. 3/8" SCALE : 3" = 1'-0" W.D. 3 3/8" EC 97911-061 W.D. 1-13/16" 1 HEAD O.D. 4 VARIES 4-5/8" 4-5/8" Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. AA™5450 DOUBLE HUNG WINDOW (1-1/2" Triple Glazed) O.D. D.L.O © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. JULY, 2014 AA™5450 Ultra Thermal Window 17 DOUBLE HUNG WINDOW 4-5/8" 1-13/16" Note: 15 PSF Sill also available with panning fin. 2-9/16" D.L.O O.D. W.D. 5 FIXED JAMB D.L.O W.D. O.D. 3/8" 3/8" 4 4 SILL 10 PSF 4 SILL 15 PSF 6 OPERABLE JAMB ADME120 3 HORIZONTAL D.L.O D.L.O 4-1/8" 5 2-9/16" D.L.O D.L.O Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 2" 1-11/16" 3/8" DOUBLE HUNG WINDOW TYPICAL ELEVATION Log onto www.kawneer.com for other configurations Note: 10 PSF Sill also available with panning fin. 3-3/4" 3/8" Note: 15 PSF Sill also available with panning fin. kawneer.com © Kawneer Company, Inc., 2014 D.L.O O.D. W.D. AA™5450 Ultra Thermal Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. D.L.O 2 HORIZONTAL 3-13/16" 1 4-13/16" 3 W.D. 1 HEAD O.D. 2 D.L.O 3/8" SCALE : 3" = 1'-0" W.D. AA™5450 DOUBLE HUNG WINDOW (Tri-Lite 1" Double Glazed) O.D. 4-5/8" 4-5/8" 18 JULY, 2014 EC 97911-061 4-5/8" 6 2-9/16" kawneer.com D.L.O O.D. W.D. 4 FIXED JAMB D.L.O O.D. 3/8" 3/8" D.L.O 3/8" 4 3 SILL 10 PSF 3 SILL 15 PSF W.D. 5 OPERABLE JAMB ADME120 W.D. D.L.O D.L.O 2 HORIZONTAL 2" D.L.O D.L.O 2 HORIZONTAL 2 4-1/8" D.L.O D.L.O 1 3-13/16" 3 W.D. 5 O.D. 1 HEAD 1-11/16" W.D. 3/8" SCALE : 3" = 1'-0" 4-13/16" AA™5450 DOUBLE HUNG WINDOW (Tri-Lite 1-1/2" Double Glazed) O.D. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-061 O.D. 4-5/8" 4-5/8" © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. JULY, 2014 AA™5450 Ultra Thermal Window 19 DOUBLE HUNG WINDOW 4-5/8" 6 TYPICAL ELEVATION Log onto www.kawneer.com for other configurations Note: 10 PSF Sill also available with panning fin. 3-3/4" 2-9/16" 3/8" Note: 15 PSF Sill also available with panning fin. AA™5450 Ultra Thermal Window EC 97911-061 A class 5 adjustable spiral balance with excellent operating forces capable of balancing heavier sash weights. The balance utilizes stainless steel components and is cycle tested for longevity. SWEEP LOCK AND KEEPER White Bronze sweep locks and keepers with a durable brushed nickel finish and cycle tested for longevity. AUTO LOCK AND KEEPER An aluminum spring operated auto lock located on the upper sash. The lock automatically engages the integral keeper securing the sash in the closed position. The auto lock is an option for the lower sash, but is standard for the upper sash. COVERED WEEPS A weep with an integral hinged cover to allow maximum drainage of infiltrating water with a positive closing cover to block drafts and insects. The weep is available in black and white finishes. SASH CAMS Adjustable glass filled nylon cams located left and right on the sash ensure proper alignment and smooth operation. SASH STOPS Black rigid vinyl sash stops are inserted into the vertical jambs without exposed fasteners to prevent excessive sash travel. ADME120 kawneer.com © Kawneer Company, Inc., 2014 HEAVY DUTY BALANCES Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. DOUBLE HUNG WINDOW JULY, 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 20 JULY, 2014 AA™5450 Ultra Thermal Window DOUBLE HUNG WINDOW UPPER SASH SNAP LOCK A White Bronze spring operated auto lock located on the upper sash. The lock automatically engages the integral keeper securing the upper sash in the closed position. The snap lock is an option for the upper sash. WHITE BRONZE SILL AUTO LOCK A White Bronze spring operated auto lock located on the lower sash. The lock automatically engages the integral keeper securing the lower sash in the closed position. The auto lock is an option for the lower sash. © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-061 kawneer.com ADME120 21 AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 HORIZONTAL SLIDING WINDOW Standard Features High Performance Architectural Grade Window Tested to U.S. and Canadian Standards Polyamide Thermal Break Screw and Spline Frame Corner Joinery Factory Silicone Glazed Interior Applied Glazing Bead Architectural Anodized Finishes and Applied Coatings Interior and Exterior Dual Finish Options Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. • • • • • • • • • Two Year Manufacturer's Warranty Horizontal Sliding Window Exterior Interior For specific product applications, Consult your Kawneer representative. ADME120 kawneer.com © Kawneer Company, Inc., 2014 Thermal Break Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 22 JULY, 2014 AA™5450 Ultra Thermal Window HORIZONTAL SLIDING WINDOW CLASS and GRADE CLASS AW-PG50-HS TESTING METHOD AAMA / WDMA / CSA / 101 / I.S.2 / A440 (NAFS) FRAME DEPTH 4-5/8" Overall Frame Depth TYPICAL WALL THICKNESS 0.070" Nominal TYPICAL MAXIMUM WINDOW SIZE 99"X 79" TYPICAL MINIMUM WINDOW SIZE 36" X 24" TYPICAL CONFIGURATIONS STANDARD INFILL OPTIONS 1" and 1-1/2" STANDARD HARDWARE White Bronze Sweep Locks Sash Stops Aluminum Sash Auto Lock (At XX Inactive Sash) OPTIONAL HARDWARE Aluminum Auto Locks OTHER OPTIONS Between the Glass Muntins Historic Beveled Exterior Glazed-in Muntins (1-1/2" max. overall thickness) Exterior and Interior Tape Applied Muntins Perimeters and Sills Exterior Pannings and Interior Trims 3 Piece Structural Mullions Male/Female horizontally stacked H-Mullion for vertical stacking Strap Anchors © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-061 kawneer.com ADME120 23 HORIZONTAL SLIDING WINDOW 1 3 6 7 2 4 TYPICAL ELEVATION Log onto www.kawneer.com for other configurations ADME120 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. AA™5450 Ultra Thermal Window kawneer.com © Kawneer Company, Inc., 2014 5 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 24 JULY, 2014 EC 97911-061 OX HORIZONTAL SLIDING WINDOW (Keyed to details on pages 25 and 26) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. kawneer.com 3/8" 1-11/16" D.L.O 5 FIXED JAMB D.L.O 3/8" 2" ADME120 D.L.O W.D. O.D. 6 INTERLOCKS W.D. 4A SLIDING SILL 10 PSF (Panning Fin) 4-7/8" D.L.O D.L.O D.L.O W.D. O.D. 3 SLIDING HEAD W.D. D.L.O O.D. W.D. 2-9/16" 2-9/16" 3/8" 3/8" EC 97911-061 4-7/8" 4 SLIDING SILL 10 PSF O.D. 3-23/32" O.D. W.D. SCALE : 3" = 1'-0" O.D. D.L.O D.L.O 2A FIXED SILL 10 PSF (Panning Fin) 3-23/32" 3/8" 2 FIXED SILL 10 PSF O.D. 1 FIXED HEAD W.D. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 AA™5450 Ultra Thermal Window HORIZONTAL SLIDING WINDOW OX HORIZONTAL SLIDING WINDOW (1" Double Glazed) D.L.O 4-5/8" W.D. 2-13/16" O.D. 7 SLIDING JAMB 3/8" 25 1-11/16" 3/8" D.L.O 5 FIXED JAMB D.L.O 2" ADME120 D.L.O W.D. O.D. 6 INTERLOCKS D.L.O Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 4-7/8" D.L.O D.L.O 2-9/16" O.D. W.D. 2-9/16" Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 4-7/8" 4A SLIDING SILL 10 PSF (Panning Fin) W.D. D.L.O 3 SLIDING HEAD W.D. D.L.O W.D. 3/8" 3/8" AA™5450 Ultra Thermal Window HORIZONTAL SLIDING WINDOW W.D. 2-13/16" O.D. 3/8" 7 SLIDING JAMB kawneer.com © Kawneer Company, Inc., 2014 3/8" 3-23/32" W.D. 4 SLIDING SILL 10 PSF O.D. D.L.O D.L.O 3/8" O.D. SCALE : 3" = 1'-0" O.D. 3-23/32" 2A FIXED SILL 10 PSF (Panning Fin) W.D. 2 FIXED SILL 10 PSF O.D. 1 FIXED HEAD O.D. 26 JULY, 2014 EC 97911-061 OX HORIZONTAL SLIDING WINDOW (1-1/2" Triple Glazed) 4-5/8" © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 kawneer.com AA™5450 Ultra Thermal Window EC 97911-061 HORIZONTAL SLIDING WINDOW XO HORIZONTAL SLIDING WINDOW (Keyed to details on pages 28 and 29) 1 5 3 6 7 2 4 TYPICAL ELEVATION Log onto www.kawneer.com for other configurations ADME120 27 2-13/16" 3/8" D.L.O 5 SLIDING JAMB D.L.O 2" ADME120 D.L.O O.D. W.D. 6 INTERLOCKS D.L.O Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. W.D. D.L.O D.L.O W.D. O.D. 2-9/16" Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 3-23/32" 4A FIXED SILL 10 PSF (Panning Fin) D.L.O 2-9/16" 3 FIXED HEAD W.D. D.L.O 3/8" 3/8" 4-5/8" 3-23/32" D.L.O O.D. W.D. AA™5450 Ultra Thermal Window HORIZONTAL SLIDING WINDOW 1-11/16" W.D. O.D. 3/8" 7 FIXED JAMB kawneer.com © Kawneer Company, Inc., 2014 3/8" 4-7/8" 4 FIXED SILL 10 PSF O.D. D.L.O 3/8" W.D. SCALE : 3" = 1'-0" O.D. 4-7/8" 2A SLIDING SILL 10 PSF (Panning Fin) O.D. 2 SLIDING SILL 10 PSF O.D. 1 SLIDING HEAD W.D. 28 JULY, 2014 EC 97911-061 XO HORIZONTAL SLIDING WINDOW (1" Double Glazed) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. kawneer.com 2-13/16" 3/8" D.L.O 5 SLIDING JAMB D.L.O 3/8" 4-7/8" W.D. 2" ADME120 D.L.O O.D. W.D. 6 INTERLOCKS 3-23/32" 4A FIXED SILL 10 PSF (Panning Fin) D.L.O D.L.O D.L.O 2-9/16" W.D. O.D. 2-9/16" 3 FIXED HEAD 3-23/32" D.L.O 3/8" 3/8" 4-5/8" W.D. D.L.O W.D. EC 97911-061 W.D. 4 FIXED SILL 10 PSF O.D. D.L.O 3/8" O.D. SCALE : 3" = 1'-0" O.D. 4-7/8" 2A SLIDING SILL 10 PSF (Panning Fin) W.D. 2 SLIDING SILL 10 PSF O.D. 1 SLIDING HEAD O.D. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 AA™5450 Ultra Thermal Window HORIZONTAL SLIDING WINDOW XO HORIZONTAL SLIDING WINDOW (1-1/2" Triple Glazed) D.L.O 1-11/16" W.D. O.D. 7 FIXED JAMB 3/8" 29 HORIZONTAL SLIDING WINDOW 1 3 6 7 2 4 TYPICAL ELEVATION Log onto www.kawneer.com for other configurations ADME120 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. AA™5450 Ultra Thermal Window kawneer.com © Kawneer Company, Inc., 2014 5 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 30 JULY, 2014 EC 97911-061 XX HORIZONTAL SLIDING WINDOW (Keyed to details on pages 31 and 32) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 2A SLIDING SILL 10 PSF (Panning Fin) kawneer.com 3/8" 2-13/16" D.L.O 5 SLIDING JAMB D.L.O 3/8" 4-7/8" 4A SLIDING SILL 10 PSF (Panning Fin) 2" ADME120 D.L.O W.D. O.D. 6 INTERLOCKS W.D. D.L.O D.L.O 3-3/4" W.D. O.D. 3-3/4" 3 SLIDING HEAD 4-7/8" D.L.O 3/8" 3/8" 4-5/8" W.D. D.L.O O.D. W.D. EC 97911-061 4-7/8" 4 SLIDING SILL 10 PSF O.D. D.L.O D.L.O O.D. W.D. SCALE : 3" = 1'-0" O.D. 4-7/8" 3/8" 2 SLIDING SILL 10 PSF O.D. 1 SLIDING HEAD W.D. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 AA™5450 Ultra Thermal Window HORIZONTAL SLIDING WINDOW XX HORIZONTAL SLIDING WINDOW (1" Double Glazed) D.L.O W.D. 2-13/16" O.D. 7 SLIDING JAMB 3/8" 31 3/8" 2-13/16" D.L.O 5 SLIDING JAMB D.L.O 3-3/4" 2" ADME120 D.L.O W.D. O.D. 6 INTERLOCKS D.L.O 2-13/16" Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 3-3/4" Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 4-7/8" 4A SLIDING SILL 10 PSF (Panning Fin) 4-7/8" 3/8" 3/8" AA™5450 Ultra Thermal Window HORIZONTAL SLIDING WINDOW W.D. 3/8" O.D. 7 SLIDING JAMB kawneer.com © Kawneer Company, Inc., 2014 D.L.O D.L.O W.D. D.L.O D.L.O W.D. W.D. 4 SLIDING SILL 10 PSF W.D. 4-7/8" O.D. 3/8" 3/8" 3 SLIDING HEAD O.D. D.L.O D.L.O O.D. W.D. SCALE : 3" = 1'-0" O.D. 4-7/8" 2A SLIDING SILL 10 PSF (Panning Fin) O.D. 2 SLIDING SILL 10 PSF O.D. 1 SLIDING HEAD W.D. 32 JULY, 2014 EC 97911-061 XX HORIZONTAL SLIDING WINDOW (1-1/2" Triple Glazed) 4-5/8" JULY, 2014 AA™5450 Ultra Thermal Window HORIZONTAL SLIDING WINDOW COMPOSITE ADJUSTABLE TANDEM ROLLER Glass filled nylon housing, die cast zamak roller support, precision sealed ball bearing rollers with nylon tires. SWEEP LOCK AND KEEPER White Bronze sweep locks and keepers with a durable brushed nickel finish and cycle tested for longevity. AUTO LOCK AND KEEPER An aluminum spring operated auto lock. The lock automatically engages the integral keeper securing the sash in the closed position. The auto lock is an option for the jamb sash. COVERED WEEPS A weep with an integral hinged cover to allow maximum drainage of infiltrating water with a positive closing cover to block drafts and insects. The weep is available in black and white finishes. © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-061 33 kawneer.com ADME120 AA™5450 Ultra Thermal Window 34 JULY, 2014 WINDLOAD CHARTS EC 97911-061 A = 15 PSF (720) B = 20 PSF (960) C = 25 PSF (1200) D = 30 PSF (1440) E = 35 PSF (1920) 2.0 1.0 12 3.0 A 8 B 7 C 2.0 D E 6 5 4 1.0 3 2 IF-1349 IF-1381 IF-1349 IF-1381 H-11054 A 10 B C D E 9 8 7 3.0 2.0 6 5 4 1.0 3 2 1 1 1 3 2 5 4 6 WINDLOAD CHARTS ARE BASED ON COMPOSITE PROPERTIES WHICH ARE CALCULATED IN ACCORDANCE WITH AAMA TIR-8 AND AAMA 505 8 7 MULLION CENTERS IN FEET UNITS WITH HORIZONTALS 0 0 2 3 4 5 6 8 7 MULLION CENTERS IN FEET UNITS WITHOUT HORIZONTALS A = 15 PSF (720) B = 20 PSF (960) C = 25 PSF (1200) D = 30 PSF (1440) E = 35 PSF (1920) MULLION CENTERS IN METERS 1.0 12 MULLION CENTERS IN METERS 1.0 12 11 A 8 B 7 C 6 D E 5 4 3.0 2.0 1.0 3 2 1 0 1 2 3 4 5 MULLION CENTERS IN FEET IF-1352 IF-1352 H-11054 WINDLOAD CHARTS ARE BASED ON COMPOSITE PROPERTIES WHICH ARE CALCULATED IN ACCORDANCE WITH AAMA TIR-8 AND AAMA 505 UNITS WITH HORIZONTALS MULLION HEIGHT IN FEET A 9 MULLION HEIGHT IN METERS 11 10 0 1 10 B C D E 9 8 7 6 3.0 2.0 5 4 1.0 3 MULLION HEIGHT IN METERS 0 2 1 0 0 1 2 3 4 5 MULLION CENTERS IN FEET UNITS WITHOUT HORIZONTALS ADME120 kawneer.com © Kawneer Company, Inc., 2014 9 MULLION HEIGHT IN FEET 10 MULLION HEIGHT IN METERS 11 MULLION HEIGHT IN FEET MULLION HEIGHT IN FEET 11 0 2.0 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 1.0 12 MULLION CENTERS IN METERS MULLION HEIGHT IN METERS MULLION CENTERS IN METERS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 psi (104 MPa). If the design wind load is determined through the analytical procedures of ASCE/SEI 7-10 or earlier editions, the load shall be based on the nominal loads used in allowable stress design. A 4/3 increase in allowable stress has not been used to develop these curves. 1-3/16" 1-3/4" © Kawneer Company, Inc., 2014 kawneer.com 5-5/32" IF-1451 S-11038 1-3/4" 2-1/2" Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 1-3/16" 1-3/4" IF-1443 5-5/32" S-11038 1-3/4" 2-1/2" Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 AA™5450 Ultra Thermal Window EC 97911-061 RECEPTORS SCALE : 3" = 1'-0" RECEPTOR DETAILS 5-7/16" IF-1442 IF-4444 5-3/8" IF-4444 5-3/8" ADME120 S-071 2" 20-0793 INTERIOR GLAZED 5-7/16" IF-1450 S-071 2" 20-0793 EXTERIOR GLAZED 35 2-1/4" ADME120 S-071 2-11/32" IF-1443 50-2130 STRAP ANCHOR WITH RECEPTOR Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 2-7/16" ANCHORS 1-15/16" 50-0973 20-0793 STRAP ANCHOR WITHOUT RECEPTOR kawneer.com © Kawneer Company, Inc., 2014 50-2130 S-11038 AA™5450 Ultra Thermal Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. IF-1444 IF-1442 36 JULY, 2014 EC 97911-061 ANCHOR DETAILS NOTE: Interior glazed shown, exterior glazed similar. 50-2130 AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 FIXED WINDOW THERMAL CHARTS Generic Project Specific U-factor Example Calculation (Percent of glass will vary on specific products depending on sitelines) 56-3/8" (1432) Example Glass U-Factor = 0.42 Btu/hr • ft2 • °F 5'-0" (1524) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 3'-0" (915) Total Daylight Opening = 32-3/8" • 56-3/8" = 12.67ft2 Total Projected Area = 3'-0" • 5'-0" = 15 ft2 Percent of Glass = (Total Daylight Opening ÷ Total Projected Area)100 = (12.67 ÷ 15)100 = 85% 32-3/8" (822) System U-factor vs Percent of Glass Area 0.44 (2.50) 0.42 (2.39) 0.40 (2.27) 0.38 (2.16) 0.36 (2.05) 0.34 (1.93) 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.85 Percent of Glass Area Based on 85% glass and center of glass (COG) U-factor of 0.42 System U-factor is equal to 0.44 Btu/hr • ft2 • °F kawneer.com ADME120 0.44 Btu hr • ft2 • °F System U-factor 0.46 (2.61) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.48 (2.73) E IGN PL S M E A D EX OR F T O N COG U-factor 37 AA™5450 Ultra Thermal Window EC 97911-061 FIXED WINDOW THERMAL CHARTS Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 JULY, 2014 AA™5450 FIXED WINDOW (1" Double Glazed) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-factor vs Percent of Glass Area COG U-factor 0.47 (2.67) 0.46 (2.61) 0.44 (2.50) 0.42 (2.39) 0.40 (2.27) 0.38 (2.16) 0.36 (2.05) 0.34 (1.93) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) 0.10 (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. ADME120 kawneer.com © Kawneer Company, Inc., 2014 Btu hr • ft2 • °F System U-factor 38 System VT © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 kawneer.com AA™5450 Ultra Thermal Window EC 97911-061 FIXED WINDOW THERMAL CHARTS AA™5450 FIXED WINDOW (1" Double Glazed) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME120 39 AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 THERMAL PERFORMANCE MATRIX (NFRC SIZE) Thermal Transmittance 1 (BTU/hr • ft 2 • °F) 0.48 0.52 0.46 0.51 0.44 0.50 0.42 0.48 0.40 0.46 0.38 0.45 0.36 0.43 0.34 0.42 0.32 0.40 0.30 0.39 0.28 0.37 0.26 0.35 0.24 0.34 0.22 0.32 0.20 0.31 0.18 0.29 0.16 0.27 0.14 0.26 0.12 0.24 0.10 0.22 AA™5450 FIXED WINDOW (1" Double Glazed) NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. SHGC Matrix 2 U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1200mm wide by 1500mm high (47-1/4" by 59-1/16"). Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.65 0.75 0.64 0.70 0.61 0.70 0.60 0.65 0.56 0.65 0.55 0.60 0.52 0.60 0.51 0.55 0.48 0.55 0.47 0.50 0.43 0.50 0.43 0.45 0.39 0.45 0.38 0.40 0.35 0.40 0.34 0.35 0.31 0.35 0.30 0.30 0.26 0.30 0.26 0.25 0.22 0.25 0.21 0.20 0.18 0.20 0.17 0.15 0.14 0.15 0.13 0.10 0.09 0.10 0.09 0.05 0.05 0.05 0.04 ADME120 kawneer.com © Kawneer Company, Inc., 2014 Overall U-Factor 4 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Glass U-Factor 3 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 40 AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 FIXED WINDOW THERMAL CHARTS Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 AA™5450 FIXED WINDOW (1-1/2" Triple Glazed) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-factor vs Percent of Glass Area COG U-factor 0.32 (1.82) Btu hr • ft2 • °F System U-factor 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) 0.10 (0.57) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.24 (1.37) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. kawneer.com ADME120 41 COG SHGC System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME120 kawneer.com © Kawneer Company, Inc., 2014 FIXED WINDOW THERMAL CHARTS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System SHGC AA™5450 Ultra Thermal Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System VT 42 JULY, 2014 EC 97911-061 AA™5450 FIXED WINDOW (1-1/2" Triple Glazed) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area Vision Area / Total Area (%) AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 FIXED WINDOW THERMAL PERFORMANCE MATRIX (NFRC SIZE) AA™5450 FIXED WINDOW (1-1/2" Triple Glazed) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Thermal Transmittance1 (BTU/hr • ft 2 • °F) Glass U-Factor 3 Overall U-Factor 4 0.32 0.37 0.30 0.35 0.28 0.33 0.26 0.32 0.24 0.30 0.22 0.29 0.20 0.27 0.18 0.26 0.16 0.24 0.14 0.22 0.12 0.21 0.10 0.19 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. SHGC Matrix 2 Visible Transmittance 2 Glass SHGC 3 Overall Glass U-Factor 4 Glass VT 3 Overall VT 4 0.75 0.65 0.75 0.64 0.70 0.60 0.70 0.60 0.65 0.56 0.65 0.55 0.60 0.52 0.60 0.51 0.55 0.48 0.55 0.47 0.50 0.43 0.50 0.43 0.45 0.39 0.45 0.38 0.40 0.35 0.40 0.34 0.35 0.31 0.35 0.30 0.30 0.26 0.30 0.26 0.25 0.22 0.25 0.21 0.20 0.18 0.20 0.17 0.15 0.13 0.15 0.13 0.10 0.09 0.10 0.09 0.05 0.05 0.05 0.04 NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC 100. 2. SHGC and VT values are determined in accordance with NFRC 200. 3. Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1200mm wide by 1500mm high (47-1/4" by 59-1/16"). kawneer.com ADME120 43 AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 SINGLE HUNG WINDOW THERMAL CHARTS Generic Project Specific U-factor Example Calculation (Percent of glass will vary on specific products depending on sitelines) 3'-0" (915) 25-3/4" (654) 5'-0" (1524) 25-3/4" (654) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 31-7/16" (799) 29-5/16" (745) Example Glass U-Factor = 0.42 Btu/hr • ft2 • °F Total Daylight Opening = (31-7/16" • 25-3/4") + (29-5/16" • 25-3/4") = 10.86 ft2 Total Projected Area = 3'-0" • 5'-0" = 15 ft2 Percent of Glass = (Total Daylight Opening ÷ Total Projected Area)100 = (10.86 ÷ 15)100 = 72% System U-factor vs Percent of Glass Area Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.85 0.80 0.75 N E IGN PL S M E A D EX OR F T O (2.73) (2.61) (2.50) (2.39) (2.27) (2.16) (2.05) (1.93) (1.82) (1.71) (1.59) (1.48) (1.37) (1.25) (1.14) 0.65 0.60 0.55 0.50 0.49 Btu hr • ft2 • °F System U-factor COG U-factor 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 0.28 0.26 0.24 0.22 0.20 0.70 0.45 0.40 0.35 0.30 0.25 0.20 70 75 60 65 55 50 Percent of Glass Area Based on 72% glass and center of glass (COG) U-factor of 0.42 System U-factor is equal to 0.49 Btu/hr • ft2 • °F ADME120 kawneer.com © Kawneer Company, Inc., 2014 0.90 72% 44 AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 SINGLE HUNG THERMAL CHARTS AA™5450 SINGLE HUNG WINDOW (1" Double Glazed - 10lb. Sill) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-factor vs Percent of Glass Area COG U-factor 0.48 (2.73) 0.46 (2.61) 0.44 (2.50) 0.42 (2.39) Btu hr • ft2 • °F System U-factor 0.40 (2.27) 0.38 (2.16) 0.36 (2.05) 0.34 (1.93) 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.32 (1.82) 0.12 (0.68) 0.10 (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. kawneer.com ADME120 45 COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME120 kawneer.com © Kawneer Company, Inc., 2014 SINGLE HUNG THERMAL CHARTS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System SHGC AA™5450 Ultra Thermal Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System VT 46 JULY, 2014 EC 97911-061 AA™5450 SINGLE HUNG WINDOW (1" Double Glazed - 10lb Sill) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 SINGLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) Thermal Transmittance 1 (BTU/hr • ft 2 • °F) Overall U-Factor 4 0.48 0.53 0.46 0.51 0.44 0.50 0.42 0.48 0.40 0.47 0.38 0.46 0.36 0.44 0.34 0.43 0.32 0.42 0.30 0.40 0.28 0.39 0.26 0.38 0.24 0.36 0.22 0.35 0.20 0.33 0.18 0.31 0.16 0.30 0.14 0.29 0.12 0.27 0.10 0.26 AA™5450 SINGLE HUNG WINDOW (1" Double Glazed - 10ib. Sill) NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. SHGC Matrix 2 U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1200mm wide by 1500mm high (47-1/4" by 59-1/16"). Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.57 0.75 0.57 0.70 0.54 0.70 0.53 0.65 0.50 0.65 0.49 0.60 0.46 0.60 0.45 0.55 0.42 0.55 0.42 0.50 0.39 0.50 0.38 0.45 0.35 0.45 0.34 0.40 0.31 0.40 0.30 0.35 0.27 0.35 0.27 0.30 0.23 0.30 0.23 0.25 0.20 0.25 0.19 0.20 0.16 0.20 0.15 0.15 0.12 0.15 0.11 0.10 0.08 0.10 0.08 0.05 0.04 0.05 0.04 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Glass U-Factor 3 kawneer.com ADME120 47 AA™5450 Ultra Thermal Window EC 97911-061 SINGLE HUNG THERMAL CHARTS AA™5450 SINGLE HUNG WINDOW (1-1/2" Triple Glazed - 10lb. Sill) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-factor vs Percent of Glass Area COG U-factor 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) 0.10 (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. ADME120 kawneer.com © Kawneer Company, Inc., 2014 Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 JULY, 2014 Btu hr • ft2 • °F System U-factor 48 System VT © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 kawneer.com AA™5450 Ultra Thermal Window EC 97911-061 SINGLE HUNG THERMAL CHARTS AA™5450 SINGLE HUNG WINDOW (1-1/2" Triple Glazed - 10lb Sill) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME120 49 50 AA™5450 Ultra Thermal Window JULY, 2014 SINGLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) EC 97911-061 AA™5450 SINGLE HUNG WINDOW (1-1/2" Triple Glazed - 10lb. Sill) Glass U-Factor 3 Overall U-Factor 4 0.32 0.37 0.30 0.35 0.28 0.33 0.26 0.32 0.24 0.30 0.22 0.29 0.20 0.27 0.18 0.26 0.16 0.24 0.14 0.22 0.12 0.21 0.10 0.19 Visible Transmittance 2 Overall Glass U-Factor 4 Glass VT 3 Overall VT 4 0.75 0.65 0.75 0.64 0.70 0.60 0.70 0.60 0.65 0.56 0.65 0.55 0.60 0.52 0.60 0.51 0.55 0.48 0.55 0.47 0.50 0.43 0.50 0.43 0.45 0.39 0.45 0.38 0.40 0.35 0.40 0.34 0.35 0.31 0.35 0.30 0.30 0.26 0.30 0.26 0.25 0.22 0.25 0.21 0.20 0.18 0.20 0.17 0.15 0.13 0.15 0.13 0.10 0.09 0.10 0.09 0.05 0.05 0.05 0.04 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Glass SHGC 3 NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC 100. 2. SHGC and VT values are determined in accordance with NFRC 200. 3. Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1200mm wide by 1500mm high (47-1/4" by 59-1/16"). ADME120 kawneer.com © Kawneer Company, Inc., 2014 SHGC Matrix 2 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Thermal Transmittance1 (BTU/hr • ft 2 • °F) AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 SINGLE HUNG THERMAL CHARTS AA™5450 SINGLE HUNG WINDOW (1" Double Glazed - 15lb. Sill) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-factor vs Percent of Glass Area COG U-factor 0.48 (2.73) 0.46 (2.61) 0.44 (2.50) 0.42 (2.39) Btu hr • ft2 • °F System U-factor 0.40 (2.27) 0.38 (2.16) 0.36 (2.05) 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.34 (1.93) 0.12 (0.68) 0.10 (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. kawneer.com ADME120 51 COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME120 kawneer.com © Kawneer Company, Inc., 2014 SINGLE HUNG THERMAL CHARTS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System SHGC AA™5450 Ultra Thermal Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System VT 52 JULY, 2014 EC 97911-061 AA™5450 SINGLE HUNG WINDOW (1" Double Glazed - 15lb Sill) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 SINGLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) Thermal Transmittance 1 (BTU/hr • ft 2 • °F) Overall U-Factor 4 0.48 0.52 0.46 0.51 0.44 0.49 0.42 0.48 0.40 0.47 0.38 0.45 0.36 0.44 0.34 0.43 0.32 0.41 0.30 0.40 0.28 0.39 0.26 0.37 0.24 0.36 0.22 0.35 0.20 0.33 0.18 0.31 0.16 0.30 0.14 0.29 0.12 0.27 0.10 0.26 AA™5450 SINGLE HUNG WINDOW (1" Double Glazed - 15lb Sill) NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. SHGC Matrix 2 U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1200mm wide by 1500mm high (47-1/4" by 59-1/16"). Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.56 0.75 0.56 0.70 0.53 0.70 0.52 0.65 0.49 0.65 0.48 0.60 0.45 0.60 0.45 0.55 0.42 0.55 0.41 0.50 0.38 0.50 0.37 0.45 0.34 0.45 0.33 0.40 0.30 0.40 0.30 0.35 0.27 0.35 0.26 0.30 0.23 0.30 0.22 0.25 0.19 0.25 0.19 0.20 0.16 0.20 0.15 0.15 0.12 0.15 0.11 0.10 0.08 0.10 0.07 0.05 0.04 0.05 0.04 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Glass U-Factor 3 kawneer.com ADME120 53 AA™5450 Ultra Thermal Window EC 97911-061 SINGLE HUNG THERMAL CHARTS Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 JULY, 2014 AA™5450 SINGLE HUNG WINDOW (1-1/2" Triple Glazed - 15lb. Sill) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-factor vs Percent of Glass Area COG U-factor 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) 0.10 (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. ADME120 kawneer.com © Kawneer Company, Inc., 2014 Btu hr • ft2 • °F System U-factor 54 System VT © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 kawneer.com AA™5450 Ultra Thermal Window EC 97911-061 SINGLE HUNG THERMAL CHARTS AA™5450 SINGLE HUNG WINDOW (1-1/2" Triple Glazed - 15lb Sill) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME120 55 56 AA™5450 Ultra Thermal Window JULY, 2014 SINGLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) EC 97911-061 AA™5450 SINGLE HUNG WINDOW (1-1/2" Triple Glazed - 15lb. Sill) Glass U-Factor 3 Overall U-Factor 4 0.32 0.38 0.30 0.37 0.28 0.36 0.26 0.34 0.24 0.33 0.22 0.31 0.20 0.30 0.18 0.29 0.16 0.27 0.14 0.26 0.12 0.24 0.10 0.23 Visible Transmittance 2 Overall Glass U-Factor 4 Glass VT 3 Overall VT 4 0.75 0.56 0.75 0.59 0.70 0.53 0.70 0.52 0.65 0.49 0.65 0.48 0.60 0.45 0.60 0.45 0.55 0.41 0.55 0.41 0.50 0.38 0.50 0.37 0.45 0.34 0.45 0.33 0.40 0.30 0.40 0.30 0.35 0.27 0.35 0.26 0.30 0.23 0.30 0.22 0.25 0.19 0.25 0.19 0.20 0.15 0.20 0.15 0.15 0.12 0.15 0.11 0.10 0.08 0.10 0.07 0.05 0.04 0.05 0.04 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Glass SHGC 3 NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC 100. 2. SHGC and VT values are determined in accordance with NFRC 200. 3. Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1200mm wide by 1500mm high (47-1/4" by 59-1/16"). ADME120 kawneer.com © Kawneer Company, Inc., 2014 SHGC Matrix 2 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Thermal Transmittance1 (BTU/hr • ft 2 • °F) AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 DOUBLE HUNG WINDOW THERMAL CHARTS Generic Project Specific U-factor Example Calculation (Percent of glass will vary on specific products depending on sitelines) 3'-0" (915) 25-11/16" (652) 5'-0" (1524) 25-11/16" (652) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 28-1/2" (724) Example Glass U-Factor = 0.42 Btu/hr • ft2 • °F Total Daylight Opening = (28-1/2" • 25-11/16") + (28-1/2" • 25-11/16") = 10.17 ft2 Total Projected Area = 3'-0" • 5'-0" = 15 ft2 Percent of Glass = (Total Daylight Opening ÷ Total Projected Area)100 = (10.17 ÷ 15)100 = 68% System U-factor vs Percent of Glass Area 0.90 0.80 0.75 N © Kawneer Company, Inc., 2014 (2.73) (2.61) (2.50) (2.39) (2.27) (2.16) (2.05) (1.93) (1.82) (1.71) (1.59) (1.48) (1.37) (1.25) (1.14) 0.65 0.60 0.55 0.50 0.45 0.40 0.35 0.30 0.25 0.20 70 65 68% 75 60 55 Percent of Glass Area Based on 68% glass and center of glass (COG) U-factor of 0.42 System U-factor is equal to 0.49 Btu/hr • ft2 • °F kawneer.com ADME120 50 0.49 Btu hr • ft2 • °F System U-factor COG U-factor 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 0.28 0.26 0.24 0.22 0.20 0.70 E IGN PL S M E A D EX OR F T O Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.85 57 AA™5450 Ultra Thermal Window EC 97911-061 DOUBLE HUNG THERMAL CHARTS Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 JULY, 2014 AA™5450 DOUBLE HUNG WINDOW (1" Double Glazed - 10lb. Sill) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-factor vs Percent of Glass Area COG U-factor 0.48 (2.73) 0.46 (2.61) 0.44 (2.50) 0.42 (2.39) 0.40 (2.27) 0.38 (2.16) 0.36 (2.05) 0.34 (1.93) 0.32 (1.82) 0.30 (1.71) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) 0.10 (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. ADME120 kawneer.com © Kawneer Company, Inc., 2014 Btu hr • ft2 • °F System U-factor 58 © Kawneer Company, Inc., 2014 System VT Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 kawneer.com AA™5450 Ultra Thermal Window EC 97911-061 DOUBLE HUNG THERMAL CHARTS AA™5450 SINGLE HUNG WINDOW (1" Double Glazed - 10lb Sill) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME120 59 AA™5450 Ultra Thermal Window JULY, 2014 DOUBLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) EC 97911-061 Thermal Transmittance 1 (BTU/hr • ft 2 • °F) 0.48 0.53 0.46 0.52 0.44 0.52 0.42 0.49 0.40 0.48 0.38 0.47 0.36 0.46 0.34 0.44 0.32 0.43 0.30 0.42 0.28 0.40 0.26 0.39 0.24 0.38 0.22 0.37 0.20 0.35 0.18 0.33 0.16 0.32 0.14 0.31 0.12 0.29 0.10 0.28 AA™5450 DOUBLE HUNG WINDOW (1" Double Glazed - 10ib. Sill) NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. SHGC Matrix 2 U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 960mm wide by 2090mm high (37-3/4" by 82-3/8"). Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.55 0.75 0.54 0.70 0.51 0.70 0.50 0.65 0.48 0.65 0.47 0.60 0.44 0.60 0.43 0.55 0.40 0.55 0.40 0.50 0.37 0.50 0.36 0.45 0.33 0.45 0.32 0.40 0.30 0.40 0.29 0.35 0.26 0.35 0.25 0.30 0.22 0.30 0.22 0.25 0.19 0.25 0.18 0.20 0.15 0.20 0.14 0.15 0.12 0.15 0.11 0.10 0.08 0.10 0.07 0.05 0.04 0.05 0.04 ADME120 kawneer.com © Kawneer Company, Inc., 2014 Overall U-Factor 4 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Glass U-Factor 3 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 60 AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 DOUBLE HUNG THERMAL CHARTS Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 AA™5450 DOUBLE HUNG WINDOW (1-1/2" Triple Glazed - 10lb. Sill) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-factor vs Percent of Glass Area COG U-factor Btu hr • ft2 • °F System U-factor 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) 0.10 (0.57) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.24 (1.37) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. kawneer.com ADME120 61 COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME120 kawneer.com © Kawneer Company, Inc., 2014 DOUBLE HUNG THERMAL CHARTS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System SHGC AA™5450 Ultra Thermal Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System VT 62 JULY, 2014 EC 97911-061 AA™5450 DOUBLE HUNG WINDOW (1-1/2" Triple Glazed - 10lb Sill) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 DOUBLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) AA™5450 DOUBLE HUNG WINDOW (1-1/2" Triple Glazed - 10lb. Sill) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Thermal Transmittance1 (BTU/hr • ft 2 • °F) Glass U-Factor 3 Overall U-Factor 4 0.32 0.39 0.30 0.38 0.28 0.37 0.26 0.35 0.24 0.34 0.22 0.33 0.20 0.31 0.18 0.30 0.16 0.29 0.14 0.27 0.12 0.26 0.10 0.25 Visible Transmittance 2 Glass SHGC 3 Overall Glass U-Factor 4 Glass VT 3 Overall VT 4 0.75 0.55 0.75 0.54 0.70 0.51 0.70 0.50 0.65 0.47 0.65 0.47 0.60 0.44 0.60 0.43 0.55 0.40 0.55 0.40 0.50 0.37 0.50 0.36 0.45 0.33 0.45 0.32 0.40 0.29 0.40 0.29 0.35 0.26 0.35 0.25 0.30 0.22 0.30 0.22 0.25 0.19 0.25 0.18 0.20 0.15 0.20 0.14 0.15 0.12 0.15 0.11 0.10 0.08 0.10 0.07 0.05 0.04 0.05 0.04 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. SHGC Matrix 2 NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC 100. 2. SHGC and VT values are determined in accordance with NFRC 200. 3. Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 960mm wide by 2090mm high (37-3/4" by 82-3/8"). kawneer.com ADME120 63 AA™5450 Ultra Thermal Window EC 97911-061 DOUBLE HUNG THERMAL CHARTS Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 JULY, 2014 AA™5450 DOUBLE HUNG WINDOW (1" Double Glazed - 15lb. Sill) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-factor vs Percent of Glass Area COG U-factor 0.48 (2.73) 0.46 (2.61) 0.44 (2.50) 0.42 (2.39) 0.40 (2.27) 0.38 (2.16) 0.36 (2.05) 0.34 (1.93) 0.32 (1.82) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) 0.10 (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. ADME120 kawneer.com © Kawneer Company, Inc., 2014 Btu hr • ft2 • °F System U-factor 64 © Kawneer Company, Inc., 2014 System VT Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 kawneer.com AA™5450 Ultra Thermal Window EC 97911-061 DOUBLE HUNG THERMAL CHARTS AA™5450 SINGLE HUNG WINDOW (1" Double Glazed - 15lb Sill) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME120 65 AA™5450 Ultra Thermal Window JULY, 2014 DOUBLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) EC 97911-061 Thermal Transmittance 1 (BTU/hr • ft 2 • °F) 0.48 0.53 0.46 0.52 0.44 0.50 0.42 0.49 0.40 0.48 0.38 0.47 0.36 0.45 0.34 0.44 0.32 0.43 0.30 0.42 0.28 0.40 0.26 0.39 0.24 0.38 0.22 0.37 0.20 0.35 0.18 0.33 0.16 0.32 0.14 0.31 0.12 0.30 0.10 0.28 AA™5450 DOUBLE HUNG WINDOW (1" Double Glazed - 15ib. Sill) NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. SHGC Matrix 2 U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 960mm wide by 2090mm high (37-3/4" by 82-3/8"). Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.54 0.75 0.53 0.70 0.50 0.70 0.49 0.65 0.47 0.65 0.46 0.60 0.43 0.60 0.42 0.55 0.40 0.55 0.39 0.50 0.36 0.50 0.35 0.45 0.33 0.45 0.32 0.40 0.29 0.40 0.28 0.35 0.26 0.35 0.25 0.30 0.22 0.30 0.21 0.25 0.19 0.25 0.18 0.20 0.15 0.20 0.14 0.15 0.11 0.15 0.11 0.10 0.08 0.10 0.07 0.05 0.04 0.05 0.04 ADME120 kawneer.com © Kawneer Company, Inc., 2014 Overall U-Factor 4 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Glass U-Factor 3 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 66 AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 DOUBLE HUNG THERMAL CHARTS Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 AA™5450 DOUBLE HUNG WINDOW (1-1/2" Triple Glazed - 15lb. Sill) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-factor vs Percent of Glass Area COG U-factor Btu hr • ft2 • °F System U-factor 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.26 (1.48) 0.10 (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. kawneer.com ADME120 67 COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME120 kawneer.com © Kawneer Company, Inc., 2014 DOUBLE HUNG THERMAL CHARTS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System SHGC AA™5450 Ultra Thermal Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System VT 68 JULY, 2014 EC 97911-061 AA™5450 DOUBLE HUNG WINDOW (1-1/2" Triple Glazed - 15lb Sill) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 DOUBLE HUNG THERMAL PERFORMANCE MATRIX (NFRC SIZE) AA™5450 DOUBLE HUNG WINDOW (1-1/2" Triple Glazed - 15lb. Sill) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Thermal Transmittance1 (BTU/hr • ft 2 • °F) Glass U-Factor 3 Overall U-Factor 4 0.32 0.39 0.30 0.38 0.28 0.37 0.26 0.35 0.24 0.34 0.22 0.33 0.20 0.31 0.18 0.30 0.16 0.29 0.14 0.27 0.12 0.26 0.10 0.25 Visible Transmittance 2 Glass SHGC 3 Overall Glass U-Factor 4 Glass VT 3 Overall VT 4 0.75 0.54 0.75 0.53 0.70 0.50 0.70 0.49 0.65 0.47 0.65 0.46 0.60 0.43 0.60 0.42 0.55 0.39 0.55 0.39 0.50 0.36 0.50 0.35 0.45 0.32 0.45 0.32 0.40 0.29 0.40 0.28 0.35 0.25 0.35 0.25 0.30 0.22 0.30 0.21 0.25 0.18 0.25 0.18 0.20 0.15 0.20 0.14 0.15 0.11 0.15 0.11 0.10 0.08 0.10 0.07 0.05 0.04 0.05 0.04 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. SHGC Matrix 2 NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC 100. 2. SHGC and VT values are determined in accordance with NFRC 200. 3. Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 960mm wide by 2090mm high (37-3/4" by 82-3/8"). kawneer.com ADME120 69 AA™5450 Ultra Thermal Window JULY, 2014 HORIZONTAL SIDING WINDOW THERMAL CHARTS EC 97911-061 Generic Project Specific U-factor Example Calculation (Percent of glass will vary on specific products depending on sitelines) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 26-3/4" (679) 3'-0" (915) 28-9/16" (725) 29-23/32" (755) 5'-0" (1524) 26-3/4" (679) Example Glass U-Factor = 0.42 Btu/hr • ft2 • °F Total Daylight Opening = (28-9/16" • 26-3/4") + (29-23/32" • 26-3/4") = 10.83 ft2 Total Projected Area = 3'-0" • 5'-0" = 15 ft2 Percent of Glass = (Total Daylight Opening ÷ Total Projected Area)100 = (10.83 ÷ 15)100 = 72% System U-factor vs Percent of Glass Area 0.90 0.80 0.75 N (2.73) (2.61) (2.50) (2.39) (2.27) (2.16) (2.05) (1.93) (1.82) (1.71) (1.59) (1.48) (1.37) (1.25) (1.14) 0.65 0.60 0.55 0.50 Btu hr • ft2 • °F System U-factor E IGN PL S M E A D EX OR F T O COG U-factor 0.48 0.46 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 0.28 0.26 0.24 0.22 0.20 0.70 0.49 0.45 0.40 0.35 0.30 0.25 0.20 70 75 60 65 55 50 Percent of Glass Area Based on 72% glass and center of glass (COG) U-factor of 0.42 System U-factor is equal to 0.49 Btu/hr • ft2 • °F ADME120 kawneer.com © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.85 72% 70 AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 HORIZONTAL SLIDER THERMAL CHARTS AA™5450 OX / XO HORIZONTAL SLIDING WINDOW (1" Double Glazed - 10lb. Sill) Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-factor vs Percent of Glass Area COG U-factor 0.48 (2.73) 0.46 (2.61) 0.44 (2.50) 0.42 (2.39) 0.40 (2.27) 0.38 (2.16) 0.36 (2.05) 0.34 (1.93) Btu hr • ft2 • °F System U-factor 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) 0.10 (0.57) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.26 (1.48) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. kawneer.com ADME120 71 COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME120 kawneer.com © Kawneer Company, Inc., 2014 HORIZONTAL SLIDER THERMAL CHARTS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System SHGC AA™5450 Ultra Thermal Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System VT 72 JULY, 2014 EC 97911-061 AA™5450 OX / XO HORIZONTAL SLIDING WINDOW (1" Double Glazed - 10lb Sill) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 HORIZONTAL SLIDER THERMAL PERFORMANCE MATRIX (NFRC SIZE) Thermal Transmittance 1 (BTU/hr • ft 2 • °F) Overall U-Factor 4 0.48 0.53 0.46 0.51 0.44 0.50 0.42 0.49 0.40 0.47 0.38 0.46 0.36 0.45 0.34 0.43 0.32 0.42 0.30 0.40 0.28 0.39 0.26 0.38 0.24 0.36 0.22 0.35 0.20 0.34 0.18 0.31 0.16 0.30 0.14 0.29 0.12 0.28 0.10 0.26 AA™5450 OX / XO HORIZONTAL SLIDING WINDOW (1" Double Glazed - 10lb Sill) NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. SHGC Matrix 2 U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1500mm wide by 1200mm high (59-1/16" by 47-1/4"). Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.57 0.75 0.56 0.70 0.53 0.70 0.53 0.65 0.49 0.65 0.49 0.60 0.46 0.60 0.45 0.55 0.42 0.55 0.41 0.50 0.38 0.50 0.38 0.45 0.34 0.45 0.34 0.40 0.31 0.40 0.30 0.35 0.27 0.35 0.26 0.30 0.23 0.30 0.23 0.25 0.19 0.25 0.19 0.20 0.16 0.20 0.15 0.15 0.12 0.15 0.11 0.10 0.08 0.10 0.08 0.05 0.04 0.05 0.04 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Glass U-Factor 3 kawneer.com ADME120 73 AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 HORIZONTAL SLIDER THERMAL CHARTS AA™5450 OX / XO HORIZONTAL SLIDING WINDOW (1-1/2" Triple Glazed - 10lb. Sill) Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-factor vs Percent of Glass Area COG U-factor 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) 0.10 (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. ADME120 kawneer.com © Kawneer Company, Inc., 2014 Btu hr • ft2 • °F System U-factor 74 System VT © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 kawneer.com AA™5450 Ultra Thermal Window EC 97911-061 HORIZONTAL SLIDER THERMAL CHARTS AA™5450 OX / XO HORIZONTAL SLIDING WINDOW (1-1/2" Triple Glazed - 10lb Sill) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME120 75 76 AA™5450 Ultra Thermal Window JULY, 2014 HORIZONTAL SLIDER THERMAL PERFORMANCE MATRIX (NFRC SIZE) EC 97911-061 AA™5450 OX / XO HORIZONTAL SLIDING WINDOW (1-1/2" Triple Glazed - 10lb. Sill) Glass U-Factor 3 Overall U-Factor 4 0.32 0.38 0.30 0.37 0.28 0.36 0.26 0.34 0.24 0.33 0.22 0.31 0.20 0.30 0.18 0.29 0.16 0.27 0.14 0.26 0.12 0.24 0.10 0.23 Visible Transmittance 2 Overall Glass U-Factor 4 Glass VT 3 Overall VT 4 0.75 0.57 0.75 0.56 0.70 0.53 0.70 0.53 0.65 0.49 0.65 0.49 0.60 0.46 0.60 0.45 0.55 0.42 0.55 0.41 0.50 0.38 0.50 0.38 0.45 0.34 0.45 0.34 0.40 0.31 0.40 0.30 0.35 0.27 0.35 0.26 0.30 0.23 0.30 0.23 0.25 0.19 0.25 0.19 0.20 0.16 0.20 0.15 0.15 0.12 0.15 0.11 0.10 0.08 0.10 0.08 0.05 0.04 0.05 0.04 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Glass SHGC 3 NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC 100. 2. SHGC and VT values are determined in accordance with NFRC 200. 3. Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1500mm wide by 1200mm high (59-1/16" by 47-1/4"). ADME120 kawneer.com © Kawneer Company, Inc., 2014 SHGC Matrix 2 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Thermal Transmittance1 (BTU/hr • ft 2 • °F) AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 HORIZONTAL SLIDER THERMAL CHARTS AA™5450 XX HORIZONTAL SLIDING WINDOW (1" Double Glazed - 10lb. Sill) Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-factor vs Percent of Glass Area COG U-factor 0.48 (2.73) 0.46 (2.61) 0.44 (2.50) 0.42 (2.39) 0.40 (2.27) 0.38 (2.16) Btu hr • ft2 • °F System U-factor 0.36 (2.05) 0.34 (1.93) 0.32 (1.82) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.30 (1.71) 0.12 (0.68) 0.10 (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. kawneer.com ADME120 77 COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME120 kawneer.com © Kawneer Company, Inc., 2014 HORIZONTAL SLIDER THERMAL CHARTS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System SHGC AA™5450 Ultra Thermal Window Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System VT 78 JULY, 2014 EC 97911-061 AA™5450 XX HORIZONTAL SLIDING WINDOW (1" Double Glazed - 10lb Sill) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 HORIZONTAL SLIDER THERMAL PERFORMANCE MATRIX (NFRC SIZE) Thermal Transmittance 1 (BTU/hr • ft 2 • °F) Overall U-Factor 4 0.48 0.53 0.46 0.52 0.44 0.50 0.42 0.49 0.40 0.48 0.38 0.47 0.36 0.45 0.34 0.44 0.32 0.43 0.30 0.41 0.28 0.40 0.26 0.39 0.24 0.38 0.22 0.36 0.20 0.35 0.18 0.32 0.16 0.32 0.14 0.30 0.12 0.29 0.10 0.28 AA™5450 XX HORIZONTAL SLIDING WINDOW (1" Double Glazed - 10lb Sill) NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. SHGC Matrix 2 U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1500mm wide by 1200mm high (59-1/16" by 47-1/4"). Visible Transmittance 2 Glass SHGC 3 Overall SHGC 4 Glass VT 3 Overall VT 4 0.75 0.54 0.75 0.53 0.70 0.51 0.70 0.50 0.65 0.47 0.65 0.46 0.60 0.43 0.60 0.43 0.55 0.40 0.55 0.39 0.50 0.36 0.50 0.36 0.45 0.33 0.45 0.32 0.40 0.29 0.40 0.28 0.35 0.26 0.35 0.25 0.30 0.22 0.30 0.21 0.25 0.19 0.25 0.18 0.20 0.15 0.20 0.14 0.15 0.11 0.15 0.11 0.10 0.08 0.10 0.07 0.05 0.04 0.05 0.04 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Glass U-Factor 3 kawneer.com ADME120 79 AA™5450 Ultra Thermal Window JULY, 2014 EC 97911-061 HORIZONTAL SLIDER THERMAL CHARTS AA™5450 XX HORIZONTAL SLIDING WINDOW (1-1/2" Triple Glazed - 10lb. Sill) Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System U-factor vs Percent of Glass Area COG U-factor 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) 0.10 (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. ADME120 kawneer.com © Kawneer Company, Inc., 2014 Btu hr • ft2 • °F System U-factor 80 System VT © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JULY, 2014 kawneer.com AA™5450 Ultra Thermal Window EC 97911-061 HORIZONTAL SLIDER THERMAL CHARTS AA™5450 XX HORIZONTAL SLIDING WINDOW (1-1/2" Triple Glazed - 10lb Sill) System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME120 81 82 AA™5450 Ultra Thermal Window JULY, 2014 HORIZONTAL SLIDER THERMAL PERFORMANCE MATRIX (NFRC SIZE) EC 97911-061 AA™5450 XX HORIZONTAL SLIDING WINDOW (1-1/2" Triple Glazed - 10lb. Sill) Glass U-Factor 3 Overall U-Factor 4 0.32 0.39 0.30 0.38 0.28 0.37 0.26 0.35 0.24 0.34 0.22 0.33 0.20 0.32 0.18 0.30 0.16 0.29 0.14 0.27 0.12 0.26 0.10 0.25 Visible Transmittance 2 Overall Glass U-Factor 4 Glass VT 3 Overall VT 4 0.75 0.54 0.75 0.53 0.70 0.51 0.70 0.50 0.65 0.47 0.65 0.46 0.60 0.43 0.60 0.43 0.55 0.40 0.55 0.39 0.50 0.36 0.50 0.36 0.45 0.33 0.45 0.32 0.40 0.29 0.40 0.28 0.35 0.26 0.35 0.25 0.30 0.22 0.30 0.21 0.25 0.18 0.25 0.18 0.20 0.15 0.20 0.14 0.15 0.11 0.15 0.11 0.10 0.08 0.10 0.07 0.05 0.04 0.05 0.04 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Glass SHGC 3 NOTE: For glass values that are not listed, linear interpolation is permitted. 1. U-Factors are determined in accordance with NFRC 100. 2. SHGC and VT values are determined in accordance with NFRC 200. 3. Glass properties are based on center of glass values and are obtained from your glass supplier. 4. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1500mm wide by 1200mm high (59-1/16" by 47-1/4"). ADME120 kawneer.com © Kawneer Company, Inc., 2014 SHGC Matrix 2 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Thermal Transmittance1 (BTU/hr • ft 2 • °F)