8225TL Thermal Window - Architectural Detail Manual

8225TL Thermal Windows
JUNE, 2015
INDEX
FIXED WINDOW................................................................................. 3-6
PROJECT-IN WINDOW.................................................................... 7-10
PROJECT-OUT WINDOW.............................................................. 11-16
INSWING CASEMENT WINDOW.................................................. 17-22
OUTSWING CASEMENT WINDOW.............................................. 23-28
MULLIONS..................................................................................... 29-31
RECEPTORS AND SUB SILLS.......................................................... 32
ANCHORING...................................................................................... 33
THERMAL CHARTS ..................................................................... 34-49
LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE,
WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE
SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS,
AND ASSUMES NO RESPONSIBILITY THEREFOR.
Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses
(
) are millimeters unless otherwise noted.
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-075
1
The following metric (SI ) units are found in these details:
m –meter
cm – centimeter
mm –millimeter
s –second
Pa –pascal
MPa –megapascal
Kawneer reserves the right to change configurations without prior notice when deemed necessary for product
improvement.
kawneer.com
ADME010
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
8225TL Thermal Windows
BLANK PAGE
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
2
JUNE, 2015
EC 97911-075
8225TL Thermal Windows
JUNE, 2015
FIXED WINDOW
Features
• Architectural Grade Window
• IsoLock™ Thermal Break
• Screw and Spline Frame Corner Joinery
• Factory Silicone Glazed
• Interior Applied Glazing Bead with Bulb Gasket
• Architectural Anodized Finishes and Applied Coatings
• Two Year Manufacturer's Warranty
Thermal Break
Exterior
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-075
Fixed Window
For specific product applications,
Consult your Kawneer representative.
kawneer.com
ADME010
Interior
3
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
FIXED WINDOW
Architectual Grade AW-PG100-FW
TESTING STANDARD
AAMA / WDMA / CSA 101 / I.S. 2 / A440 (NAFS)
2-1/4" Overall Frame Depth
TYPICAL WALL THICKNESS
.090 and .125 Nominal
TYPICAL MAXIMUM SIZE
60" x 99"
TYPICAL MINIMUM SIZE
12" x 12"
TYPICAL CONFIGURATIONS
STANDARD INFILL OPTIONS
1/4" and 1"
STANDARD HARDWARE
Not Applicable
OPTIONAL HARDWARE
Not Applicable
OTHER OPTIONS
Unequal Leg Frames
Exterior and/or Interior Applied Muntins
Perimeters and Sills
Exterior Pannings and Interior Trims
Structural Mullions
Vertically or Horizontally Stacked
Access Panels and Blinds
Silicone Field Glazing upon Request
PERFORMANCE
Air
Infiltration
Cfm/ft2
Water
Resistance
PSF
Design
Load
PSF
Thermal
Transmittance
"U" Value
Condensation
Resistance
CRF
Sound
Transmittance
STC
.10 @ 6.24 psf
15
100
.58
59
34
Note: Thermal values are based upon 1" clear insulating glass.
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
FRAME DEPTH
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
CLASS and GRADE
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
4
© Kawneer Company, Inc., 2011
2-1/4"
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
3/8"
3/8"
kawneer.com
4
2
2-1/16"
3
JAMB
D.L.O
2-1/2"
O.D.
W.D.
4
VERTICAL
MULLION
ADME010
D.L.O
O.D.
W.D.
5
2
SILL
O.D.
TYPICAL ELEVATION
Log onto www.kawneer.com for other configurations
2-1/16"
3
D.L.O
1
1
HEAD
W.D.
2-1/16"
3/8"
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
JUNE, 2015
8225TL Thermal Windows
EC 97911-075
FIXED WINDOW
SCALE : 3" = 1'-0"
2-1/4"
D.L.O
2-1/16"
W.D.
O.D.
5
JAMB
3/8"
5
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
8225TL Thermal Windows
BLANK PAGE
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
6
JUNE, 2015
EC 97911-075
8225TL Thermal Windows
JUNE, 2015
PROJECT-IN WINDOW
Features
• Architectural Grade Window
• IsoLock™ Thermal Break
• Mitered, Clipped and Staked Vent Corner Joinery
• Screw and Spline Frame Corner Joinery
• Factory Silicone Glazed
• Interior Applied Glazing Bead with Bulb Gasket
• Architectural Anodized Finishes and Applied Coatings
• Two Year Manufacturer's Warranty
• Compatible with Storefront and Curtain Wall Systems
Thermal Break
Exterior
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-075
Project-in Window
For specific product applications,
Consult your Kawneer representative.
kawneer.com
ADME010
Interior
7
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
PROJECT-IN WINDOW
Architectual Grade AP-HC90 / AP-AW90 / AP-PG90-AP
TESTING STANDARD
AAMA / WDMA / CSA 101 / I.S. 2 / A440 (NAFS)
FRAME DEPTH
2-1/4" Overall Frame Depth
TYPICAL WALL THICKNESS
.090 and .125 Nominal
TYPICAL MAXIMUM SIZE
60" x 48"
TYPICAL MINIMUM SIZE
17" x 17"
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
CLASS and GRADE
TYPICAL CONFIGURATIONS
STANDARD INFILL OPTIONS
1/4" and 1"
STANDARD HARDWARE
Stainless Steel 4-Bar Hinges
Cast White Bronze Cam Locks
OTHER OPTIONS
Unequal Leg Frames
Exterior and/or Interior Applied Muntins
Insect Screens
Perimeters and Sills
Exterior Pannings and Interior Trims
Structural Mullions
Vertically or Horizontally Stacked
Access Panels and Blinds
Silicone Field Glazing upon Request
PERFORMANCE
Air
Infiltration
Cfm/ft2
Water
Resistance
PSF
Design
Load
PSF
Thermal
Transmittance
"U" Value
Condensation
Resistance
CRF
Sound
Transmittance
STC
.10 @ 6.24 psf
15
90
.62
56
n/a
Note: Thermal values are based upon 1" clear insulating glass.
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
OPTIONAL HARDWARE
Access Control Locks
Limit Stop
Pole and Pole Ring
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
8
© Kawneer Company, Inc., 2011
2-1/4"
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
3/8"
3
3/8"
3-1/2"
kawneer.com
D.L.O
4
2
TYPICAL ELEVATION
Log onto www.kawneer.com for other configurations
D.L.O
O.D.
W.D.
W.D.
O.D.
3
JAMB
4
JAMB
ADME010
2
SILL
3-1/2"
3/8"
3-1/2"
3-1/2"
W.D.
3/8"
EC 97911-075
W.D.
O.D.
D.L.O
1
1
HEAD
O.D.
D.L.O
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
JUNE, 2015
8225TL Thermal Windows
PROJECT-IN WINDOW
SCALE : 3" = 1'-0"
2-1/4"
9
8225TL Thermal Windows
JUNE, 2015
A standard hinge for ventilators providing approximately 45° to 60°
openings depending on size. An optional limit stop is available to
restrict hinge travel and limit vent opening.
STANDARD
CAM HANDLE
Cast white bronze cam handles are standard for the manual
operation and locking of ventilators.
CAM HANDLE
WITH POLE RING
Cast white bronze cam handles with pole ring provide manual
operation of ventilators located above reach.
These handles are operated with a sash pole.
POLE RING
Cast white bronze pole ring is used in conjunction with locking
hardware for sash pole operation of ventilators.
SASH POLE
HANGER
FOR SASH POLE
ACCESS CONTROL
LOCK
A 3/4" diameter aluminum sash pole with a cast white bronze pull
down hook and black rubber tip.
Available in 6 ft. and 12 ft. lengths with optional cast white bronze
Pole Hanger.
In lieu of the standard cam handles cast white bronze access
control locks are offered for managed control of vent operations.
Lock is operated with a manganese bronze removable handle.
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
STAINLESS STEEL
4 BAR HINGES
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-075
PROJECT-IN WINDOW
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
10
8225TL Thermal Windows
JUNE, 2015
PROJECT-OUT WINDOW
Features
• Architectural Grade Window
• IsoLock™ Thermal Break
• Mitered, Clipped and Staked Vent Corner Joinery
• Screw and Spline Frame Corner Joinery
• Factory Silicone Glazed
• Interior Applied Glazing Bead with Bulb Gasket
• Architectural Anodized Finishes and Applied Coatings
• Two Year Manufacturer's Warranty
• Compatible with Storefront and Curtain Wall Systems
Thermal Break
Exterior
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-075
Project-out Window
For specific product applications,
Consult your Kawneer representative.
kawneer.com
ADME010
Interior
11
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
PROJECT-OUT WINDOW
Architectual Grade AP-HC90 / AP-AW90 / AW-PG90-AP
TESTING STANDARD
AAMA / WDMA / CSA 101 / I.S. 2 / A440 (NAFS)
2-1/4" Overall Frame Depth
TYPICAL WALL THICKNESS
.090 and .125 Nominal
TYPICAL MAXIMUM SIZE
60" x 89"
TYPICAL MINIMUM SIZE
17" x 17"
TYPICAL CONFIGURATIONS
STANDARD INFILL OPTIONS
1/4" and 1"
STANDARD HARDWARE
Stainless Steel 4-Bar Hinges
Cast White Bronze Cam Locks
88SS Support Arm (Units over 50" in height)
OPTIONAL HARDWARE
Access Control Locks
Hook Bolt Lock Handle
Pivot Shoe Roto-Operator
Scissors Arm Roto-Operator
Limit Stop
Pole and Pole Ring
OTHER OPTIONS
Unequal Leg Frames
Exterior and/or Interior Applied Muntins
Insect Screens
Perimeters and Sills
Exterior Pannings and Interior Trims
Structural Mullions
Vertically or Horizontally Stacked
Access Panels and Blinds
Silicone Field Glazing upon Request
PERFORMANCE
Air
Infiltration
Cfm/ft2
Water
Resistance
PSF
Design
Load
PSF
Thermal
Transmittance
"U" Value
Condensation
Resistance
CRF
Sound
Transmittance
STC
.10 @ 6.24 psf
15
90
.60
56
33
Note: Thermal values are based upon 1" clear insulating glass.
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
FRAME DEPTH
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
CLASS and GRADE
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
12
© Kawneer Company, Inc., 2011
2-1/4"
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
3/8"
D.L.O
3/8"
3-1/2"
kawneer.com
D.L.O
D.L.O
1
2
TYPICAL ELEVATION
Log onto www.kawneer.com for other configurations
W.D.
D.L.O
ADME010
3-1/2"
O.D.
W.D.
O.D.
3
JAMB
4
JAMB
3/8"
3-1/2"
3
O.D.
O.D.
3-1/2"
W.D.
3/8"
EC 97911-075
W.D.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
JUNE, 2015
8225TL Thermal Windows
PROJECT-OUT WINDOW
SCALE : 3" = 1'-0"
2-1/4"
1
HEAD
4
2
SILL
13
8225TL Thermal Windows
JUNE, 2015
A standard hinge for ventilators providing approximately 45° to 60°
openings depending on size. An optional limit stop is available to
restrict hinge travel and limit vent opening.
STANDARD
CAM HANDLE
Cast white bronze cam handles are standard for the manual
operation and locking of ventilators.
CAM HANDLE
WITH POLE RING
Cast white bronze cam handles with pole ring provide manual
operation of ventilators located above reach.
These handles are operated with a sash pole.
POLE RING
Cast white bronze pole ring is used in conjunction with locking
hardware for sash pole operation of ventilators.
SASH POLE
HANGER
FOR SASH POLE
ACCESS CONTROL
LOCK
A 3/4" diameter aluminum sash pole with a cast white bronze pull
down hook and black rubber tip.
Available in 6 ft. and 12 ft. lengths with optional cast white bronze
pole hanger.
In lieu of the standard cam handles cast white bronze access
control locks are offered for managed control of vent operations.
Lock is operated with a manganese bronze removable handle.
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
STAINLESS STEEL
4 BAR HINGES
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-075
PROJECT-OUT WINDOW
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
14
8225TL Thermal Windows
JUNE, 2015
PROJECT-OUT WINDOW
PIVOT-SHOE
ROTO-OPERATOR
Optional pivot shoe roto operator is located on the center line of
the bottom horizontal frame.
Standard finish shall be brushed copper nickel to match US-25-D.
HOOK BOLT LOCK
For use with pivot-shoe roto operator in lieu of cam handles.
Standard finish shall be US-25-D clear white bronze.
88SS SUPPORT ARM
Support arms are used when window height exceeds 50-1/2".
When fully extended, the hardware automatically retains the
ventilator in an open position.
SCISSORS ARM
ROTO OPERATOR
Optional scissor arm roto operator is located on the center line of
the bottom horizontal frame.
Standard finish shall be brushed copper nickel to match US-25-D.
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-075
15
kawneer.com
ADME010
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
8225TL Thermal Windows
BLANK PAGE
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
16
JUNE, 2015
EC 97911-075
8225TL Thermal Windows
JUNE, 2015
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-075
INSWING CASEMENT WINDOW
Features
• Architectural Grade Window
• IsoLock™ Thermal Break
• Mitered, Clipped and Staked Vent Corner Joinery
• Screw and Spline Frame Corner Joinery
• Factory Silicone Glazed
• Interior Applied Glazing Bead with Bulb Gasket
• Architectural Anodized Finishes and Applied Coatings
• Two Year Manufacturer's Warranty
• Compatible with Storefront and Curtain Wall Systems
Interior
Thermal Break
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
HINGED
LEFT
Exterior
Inswing Casement Window
For specific product applications,
Consult your Kawneer representative.
kawneer.com
ADME010
17
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
INSWING CASEMENT WINDOW
Architectual Grade C-HC90 / C-AW90 / AW-PG90-C
TESTING STANDARD
AAMA / WDMA / CSA 101 / I.S. 2 / A440 (NAFS)
FRAME DEPTH
2-1/4" Overall Frame Depth
TYPICAL WALL THICKNESS
.090 and .125 Nominal
TYPICAL MAXIMUM SIZE
36" x 60"
TYPICAL MINIMUM SIZE
17" x 17"
TYPICAL CONFIGURATIONS
STANDARD INFILL OPTIONS
1/4" and 1"
STANDARD HARDWARE
Stainless Steel 4-Bar Hinges
Cast White Bronze Cam Locks
OPTIONAL HARDWARE
Access Control Locks
Limit Stop
Pole and Pole Ring
Butt Hinges
Friction Adjustor
Keyed Limit Arm
OTHER OPTIONS
Unequal Leg Frames
Exterior and/or Interior Applied Muntins
Insect Screens
Perimeters and Sills
Exterior Pannings and Interior Trims
Structural Mullions
Vertically or Horizontally Stacked
Access Panels and Blinds
Silicone Field Glazing upon Request
PERFORMANCE
Air
Infiltration
Cfm/ft2
Water
Resistance
PSF
Design
Load
PSF
Thermal
Transmittance
"U" Value
Condensation
Resistance
CRF
Sound
Transmittance
STC
.10 @ 6.24 psf
15
90
.58
52
n/a
Note: Thermal values are based upon 1" clear insulating glass.
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
CLASS and GRADE
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
18
© Kawneer Company, Inc., 2011
2-1/4"
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
3/8"
2
3/8"
kawneer.com
3-1/2"
3
HINGED
LEFT
2
SILL
3-1/2"
D.L.O
W.D.
ADME010
O.D.
D.L.O
O.D.
1
HEAD
D.L.O
W.D.
3-1/2"
3/8"
EC 97911-075
W.D.
D.L.O
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
JUNE, 2015
8225TL Thermal Windows
INSWING CASEMENT WINDOW
SCALE : 3" = 1'-0"
O.D.
W.D.
O.D.
3
JAMB
4
JAMB
2-1/4"
1
4
TYPICAL ELEVATION
Log onto www.kawneer.com for other configurations
3-1/2"
3/8"
19
8225TL Thermal Windows
JUNE, 2015
A standard hinge for ventilators providing approximately 45° to 60°
openings depending on size. An optional limit stop is available to
restrict hinge travel and limit vent opening.
STANDARD
CAM HANDLE
Cast white bronze cam handles are standard for the manual
operation and locking of ventilators.
CAM HANDLE
WITH POLE RING
Cast white bronze cam handles with pole ring provide manual
operation of ventilators located above reach.
These handles are operated with a sash pole.
POLE RING
Cast white bronze pole ring is used in conjunction with locking
hardware for sash pole operation of ventilators.
SASH POLE
HANGER
FOR SASH POLE
ACCESS CONTROL
LOCK
A 3/4" diameter aluminum sash pole with a cast white bronze pull
down hook and black rubber tip.
Available in 6 ft. and 12 ft. lengths with optional cast white bronze
pole hanger.
In lieu of the standard cam handles cast white bronze access
control locks are offered for managed control of vent operations.
Lock is operated with a manganese bronze removable handle.
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
STAINLESS STEEL
4 BAR HINGES
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-075
INSWING CASEMENT WINDOW
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
20
8225TL Thermal Windows
JUNE, 2015
INSWING CASEMENT WINDOW
BUTT HINGES
An optional hinge for ventilators providing a full 90° opening.
Butt Hinges shall be finished to match the window.
FRICTION ADJUSTOR
Friction adjustors shall be used with butt hinges for additional
friction for control of the ventilator.
KEYED LIMIT ARM
Key released limit arms may be used to restrict ventilator opening
when used with butt hinges.
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-075
kawneer.com
ADME010
21
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
8225TL Thermal Windows
BLANK PAGE
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
22
JUNE, 2015
EC 97911-075
8225TL Thermal Windows
JUNE, 2015
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-075
OUTSWING CASEMENT WINDOW
Features
• Architectural Grade Window
• IsoLock™ Thermal Break
• Mitered, Clipped and Staked Vent Corner Joinery
• Screw and Spline Frame Corner Joinery
• Factory Silicone Glazed
• Interior Applied Glazing Bead with Bulb Gasket
• Architectural Anodized Finishes and Applied Coatings
• Two Year Manufacturer's Warranty
• Compatible with Storefront and Curtain Wall Systems
Thermal Break
Interior
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
HINGED
LEFT
Exterior
Outswing Casement Window
For specific product applications,
Consult your Kawneer representative.
kawneer.com
ADME010
23
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
OUTSWING CASEMENT WINDOW
Architectual Grade C-HC90 / C-AW90 / AW-PG90-C
TESTING STANDARD
AAMA / WDMA / CSA 101 / I.S. 2 / A440 (NAFS)
2-1/4" Overall Frame Depth
TYPICAL WALL THICKNESS
.090 and .125 Nominal
TYPICAL MAXIMUM SIZE
36" x 60"
TYPICAL MINIMUM SIZE
17" x 17"
TYPICAL CONFIGURATIONS
STANDARD INFILL OPTIONS
1/4" and 1"
STANDARD HARDWARE
Stainless Steel 4-Bar Hinges
Cast White Bronze Cam Locks
OPTIONAL HARDWARE
Butt Hinges
Access Control Locks
Hook Bolt Lock or Multi-Point Lock
Limit Stop
Pole and Pole Ring
Friction Adjustor
Keyed Limit Arm
Roto Operator
OTHER OPTIONS
Unequal Leg Frames
Exterior and/or Interior Applied Muntins
Insect Screens
Perimeters and Sills
Exterior Pannings and Interior Trims
Structural Mullions
Vertically or Horizontally Stacked
Access Panel and Blinds
Silicone Field Glazing upon Request
PERFORMANCE
Air
Infiltration
Cfm/ft2
Water
Resistance
PSF
Design
Load
PSF
Thermal
Transmittance
"U" Value
Condensation
Resistance
CRF
Sound
Transmittance
STC
.10 @ 6.24 psf
15
90
.60
50
37
Note: Thermal values are based upon 1" clear insulating glass.
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
FRAME DEPTH
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
CLASS and GRADE
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
24
© Kawneer Company, Inc., 2011
2-1/4"
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
3/8"
3/8"
kawneer.com
D.L.O
3-1/2"
D.L.O
HINGED
LEFT
2
SILL
W.D.
D.L.O
ADME010
O.D.
O.D.
1
HEAD
D.L.O
2
O.D.
W.D.
O.D.
3
JAMB
4
JAMB
3-1/2"
W.D.
3/8"
EC 97911-075
W.D.
3
3-1/2"
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
JUNE, 2015
8225TL Thermal Windows
OUTSWING CASEMENT WINDOW
SCALE : 3" = 1'-0"
2-1/4"
1
4
TYPICAL ELEVATION
Log onto www.kawneer.com for other configurations
3-1/2"
3/8"
25
8225TL Thermal Windows
JUNE, 2015
A standard hinge for ventilators providing approximately 45° to 60°
openings depending on size. An optional limit stop is available to
restrict hinge travel and limit vent opening.
BUTT HINGES
An optional hinge for ventilators providing a full 90° opening.
Butt hinges shall be finished to match the window.
FRICTION ADJUSTOR
Friction adjustors shall be used with butt hinges for additional
friction for control of the ventilator.
ROTO OPERATOR
Roto operators are used with butt hinges only and located at the
bottom horizontal frame. Standard finish shall be brushed copper
nickel to match US-25-D.
STANDARD
CAM HANDLE
Cast white bronze cam handles are standard for the manual
operation and locking of ventilators.
CAM HANDLE
WITH POLE RING
Cast white bronze cam handles with pole ring provide manual
operation of ventilators located above reach.
These handles are operated with a sash pole.
KEYED LIMIT ARM
Key released limit arms may be used to restrict ventilator opening
when used with butt hinges.
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
STAINLESS STEEL
4 BAR HINGES
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-075
OUTSWING CASEMENT WINDOW
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
26
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
OUTSWING CASEMENT WINDOW
Cast white bronze pole ring is used in conjunction with locking
hardware for sash pole operation of ventilators.
© Kawneer Company, Inc., 2011
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
POLE RING
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
27
SASH POLE
A 3/4" diameter aluminum sash pole with a cast white bronze pull
down hook and black rubber tip.
Available in 6 ft. and 12 ft. lengths with optional cast white bronze
pole hanger.
HANGER
FOR SASH POLE
ACCESS CONTROL
LOCK
In lieu of the standard cam handles cast white bronze access
control locks are offered for managed control of vent operations.
Lock is operated with a manganese bronze removable handle.
HOOK BOLT LOCK
Optional hook bolt lock in lieu of cam handle. Standard finish shall
be US-25-D clear white bronze.
MULTI-POINT LOCK
Optional single locking handle for concealed multi-point locks
located on the vertical frame. Standard finish shall be US-25-D
clear white bronze.
ESCAPE WINDOW SIGN
Vinyl escape window sign. Colors are white letters on red
background.
ESCAPE
WINDOW
Vinyl rescue window sign with lettering on both sides. Colors are
black letters on a yellow background.
RESCUE WINDOW SIGN
RESCUE
WINDOW
EMED CO. BUFFALO, N.Y. 1-800-442-3633 QS1848DF
kawneer.com
ADME010
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
8225TL Thermal Windows
BLANK PAGE
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
28
JUNE, 2015
EC 97911-075
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
MULLIONS
WIND LOAD CHARTS:
THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 PSI (104 MPa).
MULLION CENTERS IN METERS
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
0.5
1.0
1.5
10
3.0
2.5
8
MULLION HEIGHT IN METERS
MULLION HEIGHT IN FEET
9
7
2.0
6
A
5
1.5
B
4
C 1.0
3
D
E
2
A = 20 PSF (958)
B = 35 PSF (1436)
C = 50 PSF (2394)
D = 70 PSF (3352)
E = 90 PSF (4309)
224131
224133
0.5
1
0
1
2
3
4
5
6
MULLION CENTERS IN FEET
MULLION CENTERS IN METERS
0.5
1.0
1.5
10
A = 20 PSF (958)
B = 35 PSF (1436)
C = 50 PSF (2394)
D = 70 PSF (3352)
E = 90 PSF (4309)
3.0
2.5
8
7
2.0
6
5
1.5
A
4
1.0
3
B
MULLION HEIGHT IN METERS
MULLION HEIGHT IN FEET
9
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
UNITS WITH HORIZONTALS
C
D 0.5
E
2
1
0
1
2
3
4
5
6
MULLION CENTERS IN FEET
UNITS WITH HORIZONTALS
kawneer.com
ADME010
224138
29
8225TL Thermal Windows
30
JUNE, 2015
EC 97911-075
MULLIONS
WIND LOAD CHARTS:
THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 PSI (104 MPa).
MULLION CENTERS IN METERS
1.0
1.5
2.0
A = 20 PSF (958)
B = 25 PSF (1197)
C = 30 PSF (1436)
D = 40 PSF (1915)
3.0
2.5
MULLION HEIGHT IN FEET
8
7
2.0
6
A
5
1.5
B
C
D
4
3
1.0
MULLION HEIGHT IN METERS
9
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
0.5
10
224070
2
0.5
1
0
1
2
3
4
5
6
7
8
MULLION CENTERS IN FEET
UNITS WITH HORIZONTALS
1.5
1.0
2.0
A = 30 PSF (1436)
B = 45 PSF (2155)
C = 60 PSF (2873)
D = 75 PSF (3591)
E = 90 PSF (4309)
12
3.5
3.0
9
2.5
8
7
A 2.0
6
B
C 1.5
5
D
4
MULLION HEIGHT IN METERS
MULLION HEIGHT IN FEET
11
10
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
0.5
13
224071
E
1.0
3
2
0.5
1
0
1
2
3
4
5
6
7
8
MULLION CENTERS IN FEET
UNITS WITH HORIZONTALS
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
MULLION CENTERS IN METERS
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
MULLIONS
WIND LOAD CHARTS:
THESE CHARTS ARE BASED ON A MAXIMUM DEFLECTION OF L\175 AND\OR A MAXIMUM STRESS OF 15,152 PSI (104 MPa).
MULLION CENTERS IN METERS
1.0
1.5
2.0
A = 20 PSF (958)
B = 40 PSF (1915)
C = 60 PSF (2873)
D = 80 PSF (3830)
E = 100 PSF (4788)
13
12
3.5
11
3.0
9
B 2.5
8
7
C
6
2.0
D
E
5
1.5
4
MULLION HEIGHT IN METERS
A
10
MULLION HEIGHT IN FEET
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
0.5
224072
1.0
3
2
0.5
1
0
1
2
3
4
5
6
7
8
UNITS WITH HORIZONTALS
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
MULLION CENTERS IN FEET
NOTE:
MULLION PROJECTION TO THE
INTERIOR AVAILABLE
kawneer.com
ADME010
31
3-1/2"
(88.9)
325059
224154
1-15/16"
(49.2)
260100
5"
(127)
HEAD
RECEPTOR
3"
(76.2)
260475
260103
HEAD
RECEPTOR
3"
(76.2)
SCALE : 3" = 1'-0"
3"
(76.2)
225150
225425
3-1/8"
(79.4)
260101
4"
(101.6)
260476
5-1/2"
(139.7)
ADME010
JAMB
RECEPTOR
224154
FULL DEPTH SILLS
225151
225425
4-7/8"
(123.8)
3"
(76.2)
260475
4-1/2"
(114.3)
225152
6-7/16"
(163.5)
325059
JAMB
RECEPTOR
224154
UNEQUAL LEG SILLS
260102
260475
260104
260476
kawneer.com
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
RECEPTORS AND SUB SILLS
© Kawneer Company, Inc., 2011
325059
224154
1-15/16"
(49.2)
8225TL Thermal Windows
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
1-3/4"
(44.5)
1-1/8"
(28.6)
9/16"
(14.3)
32
JUNE, 2015
EC 97911-075
EQUAL LEG SILLS
1-15/16"
(49.2)
325059
UNEQUAL LEG SILLS
1-15/16"
(49.2)
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
JUNE, 2015
kawneer.com
8225TL Thermal Windows
229175
PVC PERIMETER
(Continuous)
Head and Jamb Similar
225081
225459
STRAP ANCHOR
with SEALANT BACK-UP
225552
2-3/4"
(69.9)
F-ANCHOR STRAP
Equal Leg Frame Only
ADME010
STRAP ANCHOR
with SUB SILL
33
EC 97911-075
SCALE : 3" = 1'-0"
225459
8225TL Thermal Windows
34
JUNE, 2015
EC 97911-075
THERMAL CHARTS
Generic Project Specific U-factor Example Calculation
(Percent of Glass will vary on specific products depending on sitelines)
5'-0"
(1524)
51-3/4"
(1315)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
3'-0"
(915)
27-3/4"
(705)
Example Glass U-Factor = 0.42 Btu/hr • ft2 • °F
Total Daylight Opening
= 27-3/4" • 51-3/4" = 9.97ft2
Total Projected Area
= 3'-0" • 5'-0" = 15 ft2
Percent of Glass
= (Total Daylight Opening ÷ Total Projected Area)100
= (9.97 ÷ 15)100 = 66%
System U-factor vs Percent of Glass Area
0.90
(4.50)
0.75
N
E IGN
PL S
M E
A D
EX OR
F
T
O
0.60
0.55
0.53
0.50
0.45
(3.50)
(3.00)
W
m2 • °C
System U-factor
(2.73)
(2.61)
(2.50)
(2.39)
(2.27)
(2.16)
(2.05)
(1.93)
(1.82)
(1.71)
(1.59)
(1.48)
(1.37)
(1.25)
(1.14)
(4.00)
0.65
Btu
hr • ft2 • °F
System U-factor
COG
U-factor
(2.50)
0.40
0.35
(2.00)
0.30
0.25
(1.50)
0.20
75
70
65
66%
0.48
0.46
0.44
0.42
0.40
0.38
0.36
0.34
0.32
0.30
0.28
0.26
0.24
0.22
0.20
0.70
60
55
50
Percent of Glass Area
Based on 66% glass and center of glass (COG) U-factor of 0.42
System U-factor is equal to 0.53 Btu/hr • ft2 • °F
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
0.80
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
(5.00)
0.85
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
THERMAL CHARTS
FIXED WINDOW WITH 1" GLAZING
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Note:
Values in parentheses are metric.
COG = Center of Glass.
Charts are generated per AMMA 507
Btu
hr • ft2 • °F
System U-factor
System U-factor vs Percent of Glass Area
0.48 (2.74)
0.46 (2.61)
0.44 (2.50)
0.42 (2.39)
0.40 (2.27)
0.38 (2.16)
0.36 (2.05)
0.34 (1.93)
0.32 (1.82)
0.30 (1.71)
0.28 (1.59)
0.26 (1.48)
0.24 (1.37)
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
COG
U-factor
0.22 (1.25)
0.20 (1.14)
Percent of Glass Area = Vision Area/Total Area
Daylight Opening / Projected Area
Notes for System U-factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values and are obtained from your glass supplier.
kawneer.com
ADME010
35
COG
VT
Vision Area / Total Area (%)
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
THERMAL CHARTS
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
System SHGC
8225TL Thermal Windows
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System VT
36
JUNE, 2015
EC 97911-075
FIXED WINDOW WITH 1" GLAZING
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
COG
SHGC
Vision Area / Total Area (%)
System Visible Transmittance (VT) vs Percent of Vision Area
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
FIXED WINDOW WITH 1" GLAZING
Thermal Transmittance 1 (BTU/hr • ft 2 • °F)
Overall U-Factor 4
0.48
0.53
0.46
0.51
0.44
0.50
0.42
0.48
0.40
0.46
0.38
0.45
0.36
0.43
0.34
0.42
0.32
0.40
0.30
0.39
0.28
0.37
0.26
0.36
0.24
0.34
0.22
0.32
0.20
0.31
NOTE:For glass values that are not listed, linear
interpolation is permitted.
1.
2.
3.
4.
SHGC Matrix 2
U-Factors are determined in accordance with NFRC 100.
SHGC and VT values are determined in accordance with
NFRC 200.
Glass properties are based on center of glass values and
are obtained from your glass supplier.
Overall U-Factor, SHGC, and VT Matricies are based on
the standard NFRC specimen size of 1200mm wide by
1500mm high (47-1/4" by 59-1/16").
Visible Transmittance 2
Glass SHGC 3
Overall SHGC 4
Glass VT 3
Overall VT 4
0.90
0.77
0.90
0.76
0.85
0.73
0.85
0.72
0.80
0.69
0.80
0.68
0.75
0.65
0.75
0.64
0.70
0.60
0.70
0.59
0.65
0.56
0.65
0.55
0.60
0.52
0.60
0.51
0.55
0.48
0.55
0.47
0.50
0.43
0.50
0.42
0.45
0.39
0.45
0.38
0.40
0.35
0.40
0.34
0.35
0.31
0.35
0.30
0.30
0.26
0.30
0.25
0.25
0.22
0.25
0.21
0.20
0.18
0.20
0.17
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Glass U-Factor 3
kawneer.com
37
ADME010
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
THERMAL CHARTS
PROJECT-IN WINDOW WITH 1" GLAZING
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Note:
Values in parentheses are metric.
COG = Center of Glass.
Charts are generated per AMMA 507
System U-factor vs Percent of Glass Area
COG
U-factor
Percent of Glass Area = Vision Area/Total Area
Daylight Opening / Projected Area
Notes for System U-factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values and are obtained from your glass supplier.
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
0.48 (2.74)
0.46 (2.61)
0.44 (2.50)
0.42 (2.39)
0.40 (2.27)
0.38 (2.16)
0.36 (2.05)
0.34 (1.93)
0.32 (1.82)
0.30 (1.71)
0.28 (1.59)
0.26 (1.48)
0.24 (1.37)
0.22 (1.25)
0.20 (1.14)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Btu
hr • ft2 • °F
System U-factor
38
System VT
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System SHGC
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
JUNE, 2015
kawneer.com
8225TL Thermal Windows
EC 97911-075
Vision Area / Total Area (%)
ADME010
39
THERMAL CHARTS
PROJECT-IN WINDOW WITH 1" GLAZING
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
COG
SHGC
Vision Area / Total Area (%)
System Visible Transmittance (VT) vs Percent of Vision Area
COG
VT
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
Overall U-Factor 4
0.48
0.59
0.46
0.58
0.44
0.57
0.42
0.56
0.40
0.55
0.38
0.54
0.36
0.53
0.34
0.51
0.32
0.50
0.30
0.49
0.28
0.48
0.26
0.47
0.24
0.46
0.22
0.45
0.20
0.44
NOTE:For glass values that are not listed, linear
interpolation is permitted.
1.
2.
3.
4.
SHGC Matrix 2
U-Factors are determined in accordance with NFRC 100.
SHGC and VT values are determined in accordance with
NFRC 200.
Glass properties are based on center of glass values and
are obtained from your glass supplier.
Overall U-Factor, SHGC, and VT Matricies are based on
the standard NFRC specimen size of 1500mm wide by
600mm high (59-1/16" by 23-5/8").
Visible Transmittance 2
Glass SHGC 3
Overall SHGC 4
Glass VT 3
Overall VT 4
0.90
0.58
0.90
0.56
0.85
0.55
0.85
0.53
0.80
0.52
0.80
0.50
0.75
0.49
0.75
0.47
0.70
0.45
0.70
0.43
0.65
0.42
0.65
0.40
0.60
0.39
0.60
0.37
0.55
0.36
0.55
0.34
0.50
0.33
0.50
0.31
0.45
0.30
0.45
0.28
0.40
0.27
0.40
0.25
0.35
0.24
0.35
0.22
0.30
0.21
0.30
0.19
0.25
0.18
0.25
0.16
0.20
0.14
0.20
0.12
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
Glass U-Factor 3
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
PROJECT-IN WINDOW
WITH 1" GLAZING
Thermal Transmittance 1 (BTU/hr • ft 2 • °F)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
40
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
THERMAL CHARTS
PROJECT-OUT WINDOW WITH 1" GLAZING
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Note:
Values in parentheses are metric.
COG = Center of Glass.
Charts are generated per AMMA 507
System U-factor vs Percent of Glass Area
Btu
hr • ft2 • °F
System U-factor
0.48 (2.74)
0.46 (2.61)
0.44 (2.50)
0.42 (2.39)
0.40 (2.27)
0.38 (2.16)
0.36 (2.05)
0.34 (1.93)
0.32 (1.82)
0.30 (1.71)
0.28 (1.59)
0.26 (1.48)
0.24 (1.37)
0.22 (1.25)
0.20 (1.14)
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
COG
U-factor
Percent of Glass Area = Vision Area/Total Area
Daylight Opening / Projected Area
Notes for System U-factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values and are obtained from your glass supplier.
kawneer.com
ADME010
41
COG
VT
Vision Area / Total Area (%)
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
THERMAL CHARTS
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
System SHGC
8225TL Thermal Windows
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System VT
42
JUNE, 2015
EC 97911-075
PROJECT-OUT WINDOW WITH 1" GLAZING
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
COG
SHGC
Vision Area / Total Area (%)
System Visible Transmittance (VT) vs Percent of Vision Area
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
PROJECT-OUT WINDOW
WITH 1" GLAZING
Thermal Transmittance 1 (BTU/hr • ft 2 • °F)
Overall U-Factor 4
0.48
0.61
0.46
0.60
0.44
0.59
0.42
0.57
0.40
0.56
0.38
0.55
0.36
0.54
0.34
0.53
0.32
0.52
0.30
0.51
0.28
0.50
0.26
0.49
0.24
0.48
0.22
0.46
0.20
0.45
NOTE:For glass values that are not listed, linear
interpolation is permitted.
1.
2.
3.
4.
SHGC Matrix 2
U-Factors are determined in accordance with NFRC 100.
SHGC and VT values are determined in accordance with
NFRC 200.
Glass properties are based on center of glass values and
are obtained from your glass supplier.
Overall U-Factor, SHGC, and VT Matricies are based on
the standard NFRC specimen size of 1500mm wide by
600mm high (59-1/16" by 23-5/8").
Visible Transmittance 2
Glass SHGC 3
Overall SHGC 4
Glass VT 3
Overall VT 4
0.90
0.58
0.90
0.56
0.85
0.55
0.85
0.53
0.80
0.52
0.80
0.50
0.75
0.49
0.75
0.47
0.70
0.46
0.70
0.43
0.65
0.42
0.65
0.40
0.60
0.39
0.60
0.37
0.55
0.36
0.55
0.34
0.50
0.33
0.50
0.31
0.45
0.30
0.45
0.28
0.40
0.27
0.40
0.25
0.35
0.24
0.35
0.22
0.30
0.21
0.30
0.19
0.25
0.18
0.25
0.16
0.20
0.15
0.20
0.12
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Glass U-Factor 3
kawneer.com
43
ADME010
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
THERMAL CHARTS
INSWING CASEMENT WINDOW WITH 1" GLAZING
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Note:
Values in parentheses are metric.
COG = Center of Glass.
Charts are generated per AMMA 507
System U-factor vs Percent of Glass Area
COG
U-factor
Percent of Glass Area = Vision Area/Total Area
Daylight Opening / Projected Area
Notes for System U-factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values and are obtained from your glass supplier.
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
0.48 (2.74)
0.46 (2.61)
0.44 (2.50)
0.42 (2.39)
0.40 (2.27)
0.38 (2.16)
0.36 (2.05)
0.34 (1.93)
0.32 (1.82)
0.30 (1.71)
0.28 (1.59)
0.26 (1.48)
0.24 (1.37)
0.22 (1.25)
0.20 (1.14)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Btu
hr • ft2 • °F
System U-factor
44
System VT
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System SHGC
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
JUNE, 2015
kawneer.com
8225TL Thermal Windows
EC 97911-075
Vision Area / Total Area (%)
ADME010
45
THERMAL CHARTS
INSWING CASEMENT WINDOW WITH 1" GLAZING
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
COG
SHGC
Vision Area / Total Area (%)
System Visible Transmittance (VT) vs Percent of Vision Area
COG
VT
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
Overall U-Factor 4
0.48
0.59
0.46
0.58
0.44
0.57
0.42
0.56
0.40
0.55
0.38
0.54
0.36
0.52
0.34
0.51
0.32
0.50
0.30
0.49
0.28
0.48
0.26
0.47
0.24
0.46
0.22
0.45
0.20
0.44
NOTE:For glass values that are not listed, linear
interpolation is permitted.
1.
2.
3.
4.
SHGC Matrix 2
U-Factors are determined in accordance with NFRC 100.
SHGC and VT values are determined in accordance with
NFRC 200.
Glass properties are based on center of glass values and
are obtained from your glass supplier.
Overall U-Factor, SHGC, and VT Matricies are based on
the standard NFRC specimen size of 600mm wide by
1500mm high (23-5/8" by 59-1/16").
Visible Transmittance 2
Glass SHGC 3
Overall SHGC 4
Glass VT 3
Overall VT 4
0.90
0.58
0.90
0.56
0.85
0.55
0.85
0.53
0.80
0.52
0.80
0.50
0.75
0.49
0.75
0.47
0.70
0.45
0.70
0.43
0.65
0.42
0.65
0.40
0.60
0.39
0.60
0.37
0.55
0.36
0.55
0.34
0.50
0.33
0.50
0.31
0.45
0.30
0.45
0.28
0.40
0.27
0.40
0.25
0.35
0.24
0.35
0.22
0.30
0.21
0.30
0.19
0.25
0.18
0.25
0.16
0.20
0.14
0.20
0.12
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
Glass U-Factor 3
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
INSWING CASEMENT WINDOW
WITH 1" GLAZING
Thermal Transmittance 1 (BTU/hr • ft 2 • °F)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
46
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
THERMAL CHARTS
OUTSWING CASEMENT WINDOW WITH 1" GLAZING
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Note:
Values in parentheses are metric.
COG = Center of Glass.
Charts are generated per AMMA 507
System U-factor vs Percent of Glass Area
Btu
hr • ft2 • °F
System U-factor
0.48 (2.74)
0.46 (2.61)
0.44 (2.50)
0.42 (2.39)
0.40 (2.27)
0.38 (2.16)
0.36 (2.05)
0.34 (1.93)
0.32 (1.82)
0.30 (1.71)
0.28 (1.59)
0.26 (1.48)
0.24 (1.37)
0.22 (1.25)
0.20 (1.14)
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
COG
U-factor
Percent of Glass Area = Vision Area/Total Area
Daylight Opening / Projected Area
Notes for System U-factor, SHGC and VT charts:
For glass values that are not listed, linear interpolation is permitted.
Glass properties are based on center of glass values and are obtained from your glass supplier.
kawneer.com
ADME010
47
COG
VT
Vision Area / Total Area (%)
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
THERMAL CHARTS
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
System SHGC
8225TL Thermal Windows
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
System VT
48
JUNE, 2015
EC 97911-075
OUTSWING CASEMENT WINDOW WITH 1" GLAZING
System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area
COG
SHGC
Vision Area / Total Area (%)
System Visible Transmittance (VT) vs Percent of Vision Area
8225TL Thermal Windows
JUNE, 2015
EC 97911-075
THERMAL PERFORMANCE MATRIX (NFRC SIZE)
OUTSWING CASEMENT WINDOW
WITH 1" GLAZING
Thermal Transmittance 1 (BTU/hr • ft 2 • °F)
Overall U-Factor 4
0.48
0.60
0.46
0.59
0.44
0.58
0.42
0.57
0.40
0.56
0.38
0.55
0.36
0.54
0.34
0.53
0.32
0.51
0.30
0.50
0.28
0.49
0.26
0.48
0.24
0.47
0.22
0.46
0.20
0.45
NOTE:For glass values that are not listed, linear
interpolation is permitted.
1.
2.
3.
4.
SHGC Matrix 2
U-Factors are determined in accordance with NFRC 100.
SHGC and VT values are determined in accordance with
NFRC 200.
Glass properties are based on center of glass values and
are obtained from your glass supplier.
Overall U-Factor, SHGC, and VT Matricies are based on
the standard NFRC specimen size of 600mm wide by
1500mm high (23-5/8" by 59-1/16").
Visible Transmittance 2
Glass SHGC 3
Overall SHGC 4
Glass VT 3
Overall VT 4
0.90
0.58
0.90
0.56
0.85
0.55
0.85
0.53
0.80
0.52
0.80
0.50
0.75
0.49
0.75
0.47
0.70
0.45
0.70
0.43
0.65
0.42
0.65
0.40
0.60
0.39
0.60
0.37
0.55
0.36
0.55
0.34
0.50
0.33
0.50
0.31
0.45
0.30
0.45
0.38
0.40
0.27
0.40
0.25
0.35
0.24
0.35
0.22
0.30
0.21
0.30
0.19
0.25
0.18
0.25
0.16
0.20
0.14
0.20
0.12
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
Glass U-Factor 3
kawneer.com
49
ADME010
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
8225TL Thermal Windows
BLANK PAGE
ADME010
kawneer.com
© Kawneer Company, Inc., 2011
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
50
JUNE, 2015
EC 97911-075