Embedded Artists’ iMX7 Dual uCOM Board rev A The Art of Embedded Systems Development – made Easy™ Document status: Preliminary iMX7 Dual uCOM Board Feature Highlights 37 mm NXP dual-core ARM Cortex-A7 and Cortex-M4 i.MX 7Dual 1GHz/200MHz 27 mm High performance 2x1800+250 DMIPS 1 GByte LPDDR3 1066 MT/s, 32-bit databus 8 GByte eMMC on-board Flash 24-bit parallel RGB and MIPI-DSI graphical output PCIe, USB, CAN and many more interfaces actual size ROHM PMIC BD71815GW with on-chip battery charger Low-power consumption - very power efficient Linux and Android BSP 27 x 37 mm ultra small form factor Long term availability Introduction The iMX7 Dual uCOM Board provides a quick and easy solution for implementing a high-performance ARM dual-core Cortex-A7 / Cortex-M4 based design. The Cortex-A7 / Cortex-M4 heterogeneous architecture enables the system to run an OS like Linux on the dual-core Cortex-A7 and a Real-Time OS (RTOS) on the Cortex-M4. The i.MX 7Dual supports 2D graphical acceleration and has dual display outputs (RGB and MIPI-DSI). The design has a low-power implementation with LPDDR3 memories and a PMIC supporting DVFS techniques and integrated battery charger, making the board ideal for portable applications. Other typical applications are graphical interface solutions, communication solutions and connected real-time systems. Specification Processor Cores Frequency Memory SDRAM NAND FLASH Parallel RGB MIPI-DSI Graphics Engine CMOS sensor interface (camera) Graphics output Graphics input Ethernet I/O (all functions are not available at the same time) Other PCIe USB UART, SPI, I2C, Audio CAN GPIO Memory card ADC Boot parameters Watchdog RTC Power Management (PMIC) Battery Charger White LED Driver Embedded Artists AB Davidshallsgatan 16 SE-211 45 Malmö Sweden NXP dual-core ARM Cortex-A7 and Cortex-M4 i.MX 7Dual 1 GHz on Cortex-A7 200 MHz on Cortex-M4 1 GByte LPDDR3 1066 MT/s, 32-bit databus 8 GByte eMMC NAND Flash for OS and bootloader 24-bit, up to 1920 x 1080 pixels at 60 Hz 2 lanes, maximum bit rate of 1.5 Gbps PXP - PiXel processing pipeline for imagine resize, rotation, overlay and color space conversion. Parallel, up to 24 bit Serial, MIPI-CSI2, 2 lanes, maximum bit rate of 1.5 Gbps Two 10/100/1000 Mbps Gigabit Ethernet interfaces (requires off-board Ethernet-PHY) 1x PCIe 2.0, 1x lane 2x USB2.0 OTG 7x UART, 4x SPI, 4x I2C, 3x I2S/SSI 2x CAN bus 2.0B Large number of GPIOs and keypad pins available 2x SD3.0/MMC5.0 2x 4ch 12-bit resolution E2PROM storing board information including Ethernet MAC address and memory bus setup params. On-board watchdog functionality ROHM BD71815GW integrated low-power RTC ROHM BD71815GW supporting DVFS techniques for low power modes ROHM BD71815GW with Coulomb counter for battery fuel gauging. Up to 28V input voltage 25mA, up to 26V Phone/Fax: +46 (0)40-611 00 93 http://www.embeddedartists.com © Copyright 2016 Embedded Artists AB. All rights reserved. All other products or service names mentioned herein are trademarks of their respective holders and should be treated as such. Privacy policy: http://www.embeddedartists.com/privacy.php Legal: http://www.embeddedartists.com/legal.php Embedded Artists’ iMX7 Dual uCOM Board rev A The Art of Embedded Systems Development – made Easy™ Power Supply voltage Power consumption Operating Temperature Operating Humidity Dimensions (W x D) Environment Mechanical Connectors Document status: Preliminary +3.3V TBD 0 - 70° or -20 - 85° Celsius 5 - 90% relative humidity, non-condensing 27 x 37 mm 70 pos DF40C-70DP-0.4V connector with 0.4mm pitch Dual 100 pcs DF40C-100DP-0.4V connector with 0.4mm pitch Block Diagram Parameter storage PMIC 3.3V input NXP i.MX 7Dual with dual-core ARM Cortex-A7 / Cortex-M4 @ 1 GHz / 200 MHz LPDDR3 Memory (32 bit data bus) SD3 eMMC Flash I2C#0 Boot control 70 pos + 2x 100 pos DF40C connector (270 pins in total) Ordering Information Part No.[1] CPU SDRAM eMMC EAC00266 MCIMX7D7DVK10S 1 GByte LPDDR3 [2] EAC00267 MCIMX7D3EVK10S 1 GByte LPDDR3 [1] Standard configurations listed. Others on request. [2] Non-stocked version 8 GByte 8 GByte Supply Voltage 3.3V 3.3V Operating Temperature 0 - 75° C -20 - 85° C Support Highlights Development Kit Embedded Artists is a reliable and competent partner - we help you become successful! Professional and responsive support Pre-designed standard Carrier boards for integration Custom Carrier board design Customization o Different pinning, supply voltage, memory sizes, etc o Single Board Computer (SBC) solutions Display solutions Mechanical solutions Schematic review of customer carrier board designs Driver and application development The iMX7 Dual uCOM Board is supported by the iMX7 Dual uCOM Developer's Kit that provides a quick path to get started with development and integration work. The kit provides reference implementations of key interfaces. Ordering part No. EAK00268 Disclaimer: Embedded Artists reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. Embedded Artists AB Davidshallsgatan 16 SE-211 45 Malmö Sweden Phone/Fax: +46 (0)40-611 00 93 http://www.embeddedartists.com © Copyright 2016 Embedded Artists AB. All rights reserved. All other products or service names mentioned herein are trademarks of their respective holders and should be treated as such. Privacy policy: http://www.embeddedartists.com/privacy.php Legal: http://www.embeddedartists.com/legal.php