PD Series FEATURES • • • • • • Low cost 100% burn-in Small size, light weight Overvoltage protection Overcurrent protection Three wide input ranges: 10–30VDC, 20–60VDC, 30–90VDC SPECIFICATIONS OPERATING INPUT Input voltage Input current 10–30VDC (PD40 & 65 – L series) 20–60VDC (PD40 & 65 – M series) 30–90VDC (PD40 & 65 – H series) 10–20VDC (PD110 – L series) 18–36VDC (PD110 – M series) 36–72VDC (PD110 – H series) MTBF Switching frequency 100,000 hours minimum at full load at 25°C ambient 32kHz ±5kHz Efficiency 70% minimum at full load Line regulation ±0.5% maximum at full load 4.1A (rms) for 24VDC typical for PD65 2.1A (rms) for 48VDC typical for PD65 1.5A (rms) for 72VDC typical for PD65 Withstand voltage 1000VDC from input to output ENVIRONMENTAL Output voltage/current See rating chart Total output power 40W, 65W and 110W Operating temperature 0°C to +70°C Derating Derate from 100% at +50°C linearly to 50% at +70°C Storage temperature -40°C to +85°C Ripple & noise 1% pk-pk max. Relative humidity Overvoltage protection Set at 112–132% of its nominal output voltage Overcurrent protection All outputs protected to short circuit conditions Temperature coefficient All outputs ±0.04% per °C maximum Transient response Maximum excursion of 4% or better on all models, recovering to 1% of final value within 500µs after a 25% step load change Output derating See notes OUTPUT Doc. No. PBC9 Rev.C 28-4-11 DC-DC CONVERTERS 4 0 - 1 1 0 W AT T S W I D E I N P U T 5%–95% non-condensing STANDARDS AND APPROVALS C-Tick AS/NZCISPR11 Group 1, Class A Powering Progress – www.powerbox.com.au 111 DC-DC CONVERTERS PD Series 4 0 - 1 1 0 W AT T S W I D E I N P U T SELECTION TABLE PD40 SERIES (40W) MODEL NUMBER OUTPUT #1 OUTPUT #2 VNOM. IMIN. IMAX. OUTPUT #3 TOL. VNOM. IMIN. IMAX. TOL. MAXIMUM OUTPUT POWER VNOM. IMIN. IMAX. TOL. PD40-10 5V 0A 8.0A 2% 40W PD40-12 12V 0A 3.5A 1% 40W PD40-13 15V 0A 3.0A 1% 40W PD40-14 24V 0A 2.0A 1% 40W PD40-23 +5V 0.5A 3.0A 3% +12V 0.2A 2A 5% 40W PD40-24 +5V 0.5A 3.0A 3% +15V 0.2A 2A 5% 40W PD40-25 +5V 0.5A 3.0A 3% +24V 0.1A 1A 5% PD40-30 +5V 0.5A 3.0A 3% +12V 0.2A 2A 5% -5V 0A 0.8A 5% 40W PD40-31 +5V 0.5A 3.0A 3% +12V 0.2A 2A 5% -12V 0A 0.8A 5% 40W PD40-32 +5V 0.5A 3.0A 3% +15V 0.2A 2A 5% -15V 0A 0.8A 5% 40W PD40-33 +5V 0.5A 3.0A 3% +15V 0.2A 2A 5% -12V 0A 0.8A 5% 40W PD40-39 +5V 0.5A 3.0A 3% +24V 0.1A 1A 5% -12V 0A 0.8A 5% 40W 40W NOTES 1. All multi-output units may be operated at no load without damage. At no load, output tolerance increases to 10% 2. Suffix codes for mechanical format and input range are as follows. PD40-XXYZ; “XX” is the model code from the above table, “Y” is the input range (L = 10–30VDC, M = 20–60VDC, H = 30–90VDC) and “Z” is the mechanical format (A = open PCB, B=L-bracket, C=enclosed), eg, PD40-31MC (20–60VDC input range, enclosed). 3. “L” series is suitable only for 75% of the above stated maximum output power. TECHNICAL ILLUSTRATION PD40 ENCLOSED NOTES 1. Dimensions shown in inch (mm) 2. Tolerance 0.02 (0.5) maximum 3. Input connector mates with Molex housing 09-50-3041 and Molex 2878 series crimp terminal 4. Output connector mates with Molex housing 09-50-3061 and Molex 2878 series crimp terminal 5. Weight: 300 grams approx (PCB format) 6. For the mechanical details of L-bracket and enclosed formats please consult sales office PIN CHART MODEL PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 RETURN RETURN RETURN N/C PD40-10 PD40-12 OUTPUT OUTPUT OUTPUT PD40-13 PD40-14 #1 #1 #1 PD40-23 PD40-24 OUTPUT OUTPUT OUTPUT COMMON COMMON #2 #1 #1 RETURN RETURN PD40-25 PD40-30 PD40-31 OUTPUT OUTPUT OUTPUT COMMON COMMON OUTPUT PD40-32 PD40-33 #2 #1 #1 RETURN RETURN #3 PD40-39 112 DOC. NO. PBC9 REV.C 28-4-11 PD Series SELECTION TABLE PD65 SERIES (65W) MODEL NUMBER OUTPUT #1 OUTPUT #2 OUTPUT #3 MAXIMUM OUTPUT POWER OUTPUT #4 VNOM. IMIN. IMAX. TOL. VNOM. IMIN. IMAX. TOL. VNOM. IMIN. IMAX. TOL. VNOM. IMIN. IMAX. TOL. PD65-10 5V 0A 10A 1% 50W PD65-12 12V 0A 5.5A 1% 65W PD65-13 15V 0A 4.5A 1% 65W PD65-14 24V 0A 3.0A 1% 65W PD65-23 +5V 1A 6.0A 3% +12V 0.5A 3A 5% 65W PD65-24 +5V 1A 6.0A 3% +15V 0.4A 3A 5% 65W PD65-25 +5V 1A 6.0A 3% +24V 0.3a 2a 5% PD65-30 +5V 1A 6.0A 3% +12V 0.5A 3A 5% -5V 0.1A 0.5A 10% 65W PD65-31 +5V 1A 6.0A 3% +12V 0.5A 3A 5% -12V 0.1A 0.5A 10% 65W PD65-32 +5V 1A 6.0A 3% +15V 0.4A 3A 5% -15V 0.1A 0.5A 10% 65W PD65-33 +5V 1A 6.0A 3% +15V 0.4A 3A 5% -12V 0.1A 0.5A 10% 65W PD65-39 +5V 1A 6.0A 3% +24V 0.3A 2A 5% -12V 0.1A 0.5A 10% PD65-40 +5V 1A 6.0A 3% +12V 0.5A 3A 5% -12V 0.1A 0.5A 10% 65W DC-DC CONVERTERS 4 0 - 1 1 0 W AT T S W I D E I N P U T 65W -5V 0.1A 0.5A 10% 65W NOTES 1. All multi-output units may be operated at no load without damage. At no load, output tolerance increases to 10%. 2. Suffix codes for mechanical format and input range are as follows: PD65-XXYZ; “XX” is the model code from the above table, “Y” is the input range (L = 10–30VDC, M = 20–60VDC, H = 30–90VDC) and “Z” is the mechanical format (A = open PCB, B = L-bracket, C = enclosed), eg, PD65-31MC (20–60VDC input range, enclosed). 3. The models for 10–30VDC input range are suitable only for 70% of the above stated maximum output power. TECHNICAL ILLUSTRATION PD65 ENCLOSED NOTES 1. Dimensions shown in inch (mm) 2. Tolerance 0.02 (0.5) maximum 3. Input connector mates with Molex housing 09-50-3031 and Molex 2878 series crimp terminal 4. Output connector mates with Molex housing 09-50-3081 and Molex 2878 series crimp terminal 5. Weight: 380 grams approx (PCB format) 6. For the mechanical details of L-bracket and enclosed formats please consult sales office PIN CHART MODEL PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 OUTPUT OUTPUT OUTPUT OUTPUT RETURN RETURN RETURN RETURN COMMON OUTPUT OUTPUT N/C N/C RETURN RETURN #2 #2 OUTPUT COMMON COMMON OUTPUT OUTPUT OUTPUT N/C PD65-10 PD65-12 PD65-13 PD65-14 #1 #1 #1 #1 PD65-23 PD65-24 OUTPUT OUTPUT COMMON #1 #1 OUTPUT PD65-25 PD65-30 PD65-31 PD65-32 PD65-33 #1 #1 RETURN RETURN #2 #2 #3 PD65-39 OUTPUT OUTPUT OUTPUT COMMON COMMON OUTPUT OUTPUT OUTPUT PD65-40 #1 #1 RETURN RETURN #2 #2 #3 #4 Doc. No. PBC9 Rev.C 28-4-11 Powering Progress – www.powerbox.com.au 113 DC-DC CONVERTERS PD Series 4 0 - 1 1 0 W AT T S W I D E I N P U T SELECTION TABLE PD110 SERIES (110W) MODEL NUMBER OUTPUT #1 OUTPUT #2 OUTPUT #3 OUTPUT #4 VNOM IMIN. IMAX. TOL. VNOM. IMIN. IMAX. IPEAK TOL. VNOM IMIN. IMAX. TOL. VNOM. IMIN. IMAX. TOL. . . MAXIMUM OUTPUT POWER PD110-10 5V 0A 22A 3% 110W PD110-12 12V 0A 9.0A 2% 110W PD110-13 15V 0A 7.5A 2% 110W PD110-14 24V 0A 4.5A 2% 110W PD110-16 30V 0A 3.6A 2% 110W PD110-23 +5V 0.8A 10A 3% +12V 0A 5A 9.0A 3% PD110-31 +5V 0.8A 10A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% 110W PD110-32 +5V 0.8A 10A 3% +15V 0A 4A 7.5A 3% -15V 0A 1A 4% 110W PD110-40 +5V 0.8A 10A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% -5V 0A 1A 4% 110W PD110-41 +5V 0.8A 10A 3% +15V 0A 4A 7.5A 3% -15V 0A 1A 4% +24V 0A 1A 4% 110W PD110-42 +5V 0.8A 10A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% +12V 0A 1A 4% 110W PD110-45-1 +5V 0.8A 10A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% +24V 0A 1.5A 10% 110W PD110-45-2 +5V 0.8A 10A 3% +24V 0A 3A 5.0A 3% -12V 0A 1A 4% +12V 0A 1A 4% 110W PD110-46 +5V 0.8A 10A 3% +15V 0A 4A 7.5A 3% -15V 0A 1A 4% -5V 0A 1A 4% 110W 110W NOTES 1. Peak output current with 10% maximum duty cycle for less than 60 seconds. 2. PD110 “M” & “H” series are suitable only for 110W maximum at 20 CFM forced air cooling or 80W maximum at convection cooling. PD110 “L” series are suitable only for 90W maximum at 20 CFM forced air cooling or 70W maximum at convection cooling. 3. Suffix codes for input range, mechanical format and connector are as follows: PD110-X1X2X3X4X5, “X1X2” is the model code from the above table, “X3” is the input range (L = 10–20VDC, M = 18–36VDC, H = 36–72VDC), “X4” is the mechanical format (A = open PCB, B = L-bracket, C = enclosed) and “X5” is the input and output connector code (Blank + Molex KK type, T = miniature terminal block), eg, PD110–31MCT (18–36VDC input range, enclosed format and miniature terminals blocks). TECHNICAL ILLUSTRATION PD110 Enclosed PIN CHART MINI TERMINAL MOLEX CONNECTOR MODEL PD110-10 PD110-13 PD110-16 PD110-23 PD110-12 PD110-14 PD110-31 PD110-32 PD110-40 PD110-41 PD110-42 PD110-45-1 PD110-45-2 PD110-46 114 1 1,2,3 2 4,5 3 6,7 4 8,9 10 5 11 12 6 13 OUTPUT #1 RETURN RETURN OUTPUT #1 N/C N/C KEY N/C OUTPUT #1 OUTPUT #1 OUTPUT #1 COMMON RETURN COMMON RETURN COMMON RETURN COMMON RETURN COMMON RETURN COMMON RETURN OUTPUT #2 OUTPUT #2 OUTPUT #2 N/C N/C N/C KEY N/C OUTPUT #3 OUTPUT #3 KEY N/C KEY OUTPUT N/C DOC. NO. PBC9 REV.C 28-4-11