13/11/02 3:25 pm Page 1 DC/DC Converters 110 Watts XPiQ inc. PD110 Series Intelligent Design Quality Product • Low Cost • 100% Burn-In • Small Size, Light Weight • Three Wide Input Ranges • Overvoltage Protection • Overcurrent Protection Specification All specifications typical at nominal line, full load and 25°C General Input Input Voltage • Input Current • 10 to 20 VDC (PD110 “L” series) 18 to 36 VDC (PD110 “M” series) 36 to 72 VDC (PD110 “H” series) 15A (rms) for 12 VDC 9.4A (rms) for 24 VDC 4.7A (rms) for 48 VDC Output Output Voltage/ Current Ripple Overvoltage Protection Overcurrent Protection: Temperature Coefficient: • See rating chart • • 1% peak to peak maximum Provided on output #1 only, set at 112-132% of its nominal output voltage All outputs protected in short circuit conditions All outputs ±0.04%/°C maximum • • Efficiency Hold-up time Line Regulation Isolation Voltage • • • • 60% minimum 10 msec ±0.5% max. 1000 VDC from input to output Environmental Operating Temperature Storage Temperature MTBF Weight • 0°C to +70°C* • -40°C to +85°C • • 100,000 hours 670 g without cover * Derate linearly from 100% load to 50°C to 50% load at 70°C • 53 • PD110 www.XP-iQ.com PH: 508 429.9883 FAX: 800 226.2100 Email: [email protected] Holliston, MA 01746 USA 13/11/02 3:25 pm Page 2 OUTPUT VOLTAGE & CURRENT RATINGS Output #1 Model PD110-10 PD110-12 PD110-13 PD110-14 PD110-16 PD110-23 PD110-31 PD110-32 PD110-40 PD110-41 PD110-42 PD110-45-1 PD110-45-2 PD110-46 Vnom 5V 12 V 15 V 24 V 30 V +5 V +5 V +5 V +5 V +5 V +5 V +5 V +5 V +5 V Imin 0.0 A 0.0 A 0.0 A 0.0 A 0.0 A 0.8 A 0.8 A 0.8 A 0.8 A 0.8 A 0.8 A 0.8 A 0.8 A 0.8 A Imax 22.0 A 9.0 A 7.5 A 4.5 A 3.6 A 10.0 A 10.0 A 10.0 A 10.0 A 10.0 A 10.0 A 10.0 A 10.0 A 10.0 A Output #2 Tol. 3% 2% 2% 2% 2% 3% 3% 3% 3% 3% 3% 3% 3% 3% PD110 Output #3 (1) Vnom Imax Ipeak Tol. Vnom Imin +12 +12 +15 +12 +15 +12 +12 +24 +15 9.0 9.0 7.5 9.0 7.5 9.0 9.0 5.0 7.5 3% 3% 3% 3% 3% 3% 3% 5% 3% -12 -15 -12 -15 -12 -12 -12 -15 0 0 0 0 0 0 0 0 V V V V V V V V V 5 5 4 5 4 5 5 3 4 A A A A A A A A A A A A A A A A A A V V V V V V V V A A A A A A A A Imax 1 1 1 1 1 1 1 1 A A A A A A A A Output #4 Tol. Vnom Imin 4% 4% 4% 4% 4% 4% 4% 4% -5 +24 +12 +24 +12 -5 0 0 0 0 0 0 V V V V V V A A A A A A Imax 1 1 1 3 1 1 Tol. A A A A A A 4% 4% 4% 8% 4% 4% Maximum Output Power 110 W 110 W 110 W 110 W 110 W 110 W 110 W 110 W 110 W 110 W 110 W 110 W 110 W 110 W Notes 1. 2. 3. 4. • PD110 For output #2, minimum load is 0 A and peak current is shown for 10% maximum duty cycle for less than 60 seconds. PD110 “M” & “H” series is suitable for 110 watts maximum at 20 CFM forced air cooling or 80 watts maximum at convection cooling. PD110 “L” series is suitable for 90 watts maximum at 20 CFM forced air cooling or 70 watts maximum at convection cooling. Suffix codes for mechanical format and input range are as follows: PD110-XXYZ: “XX” is the model code from the above table. “Y” is the input range. (L=10-20VDC, M=18-36VDC, H=36-72VDC); “Z” is the mechanical format (A=open PCB, C=enclosed) EX: PD110-31MC, 18-36VDC input, enclosed form. Pin Chart 1, 2, 3 4, 5 6, 7 8, 9 10 11 12 13 PD110-10, PD110-12 Model OUTPUT RETURN RETURN OUTPUT N.C. N.C. KEY N.C. PD110-13, PD110-14 #1 N.C. N.C. KEY N.C. N.C. OUTPUT KEY N.C. KEY OUTPUT #1 PD110-16 PD110-23 PD110-31, PD110-32 PD110-40, PD110-41 PD110-42, PD110-45-1 OUTPUT COMMON COMMON OUTPUT #1 RETURN RETURN #2 OUTPUT COMMON COMMON OUTPUT #1 RETURN RETURN #2 OUTPUT COMMON COMMON OUTPUT #1 RETURN RETURN #2 #3 N.C. OUTPUT #3 #4 PD110-45-2, PD110-46 Mechanical Details OPEN PCB “A” ENCLOSED “C” Dimensions shown in inches (mm). Tolerance 0.02 (0.5) maximum. Input connector mates with Molex housing 09-50-3051 and Molex 2878 series crimp terminal. Output connector mates with Molex housing 09-50-3131 and Molex 2878 series crimp material. www.XP-iQ.com PH: 508 429.9883 FAX: 800 226.2100 Email: [email protected] Holliston, MA 01746 USA 54