OPEN FRAME & ENCLOSED PD Series 4 0 - 1 1 0 W AT T S W I D E I N P U T Features • • • • • • Low cost 100% burn-in Small size, light weight Overvoltage protection Overcurrent protection Three wide input ranges: 10–30VDC, 20–60VDC, 30–90VDC Specifications OPERATING INPUT Input voltage Input current 10–30VDC (PD40 & 65 – L series) 20–60VDC (PD40 & 65 – M series) 30–90VDC (PD40 & 65 – H series) 10–20VDC (PD110 – L series) 18–36VDC (PD110 – M series) 36–72VDC (PD110 – H series) 4.1A (rms) for 24VDC typical for PD65 2.1A (rms) for 48VDC typical for PD65 1.5A (rms) for 72VDC typical for PD65 OUTPUT 122 MTBF 100,000 hours minimum at full load at 25°C ambient Switching frequency 32kHz ±5kHz Efficiency 70% minimum at full load Line regulation ±0.5% maximum at full load Withstand voltage 1000VDC from input to output ENVIRONMENTAL Operating temperature Derating 0°C to +70°C Derate from 100% at +50°C linearly to 50% at +70°C Output voltage/current See rating chart Total output power 40W, 65W and 110W Storage temperature -40°C to +85°C Ripple & noise 1% pk-pk max. Relative humidity 5%–95% non-condensing Overvoltage protection Set at 112–132% of its nominal output voltage STANDARDS AND APPROVALS Overcurrent protection All outputs protected to short circuit conditions C-tick Temperature coefficient All outputs ±0.04% per °C maximum Transient response Maximum excursion of 4% or better on all models, recovering to 1% of final value within 500µs after a 25% step load change Output derating See notes AS/NZCISPR11 Group 1, Class A 4 0 - 1 1 0 W AT T S W I D E I N P U T Selection Table PD40 SERIES (40W) OUTPUT #1 MODEL NUMBER VNOM. IMIN. IMAX. OUTPUT #2 TOL. VNOM. IMIN. IMAX. OUTPUT #3 TOL. VNOM. IMIN. IMAX. TOL. MAXIMUM OUTPUT POWER PD40-10 5V 0A 8.0A 2% 40W PD40-12 12V 0A 3.5A 1% 40W PD40-13 15V 0A 3.0A 1% 40W PD40-14 24V 0A 2.0A 1% PD40-23 +5V 0.5A 3.0A 3% +12V 0.2A 2A 5% 40W PD40-24 +5V 0.5A 3.0A 3% +15V 0.2A 2A 5% 40W PD40-25 +5V 0.5A 3.0A 3% +24V 0.1A 1A 5% 40W PD40-30 +5V 0.5A 3.0A 3% +12V 0.2A 2A 5% -5V 0A 0.8A 5% 40W PD40-31 +5V 0.5A 3.0A 3% +12V 0.2A 2A 5% -12V 0A 0.8A 5% 40W PD40-32 +5V 0.5A 3.0A 3% +15V 0.2A 2A 5% -15V 0A 0.8A 5% 40W PD40-33 +5V 0.5A 3.0A 3% +15V 0.2A 2A 5% -12V 0A 0.8A 5% 40W PD40-39 +5V 0.5A 3.0A 3% +24V 0.1A 1A 5% -12V 0A 0.8A 5% 40W OPEN FRAME & ENCLOSED PD Series 40W NOTES 1. All multi-output units may be operated at no load without damage. At no load, output tolerance increases to 10% 2. Suffix codes for mechanical format and input range are as follows. PD40-XXYZ; “XX” is the model code from the above table, “Y” is the input range (L = 10–30VDC, M = 20–60VDC, H = 30–90VDC) and “Z” is the mechanical format (A = open PCB, B=L-bracket, C=enclosed), eg, PD40-31MC (20–60VDC input range, enclosed). 3. “L” series is suitable only for 75% of the above stated maximum output power. Technical Illustration PD40 ENCLOSED NOTES 1. Dimensions shown in inch (mm) 2. Tolerance 0.02 (0.5) maximum 3. Input connector mates with Molex housing 09-50-3041 and Molex 2878 series crimp terminal 4. Output connector mates with Molex housing 09-50-3061 and Molex 2878 series crimp terminal 5. Weight: 300 grams approx (PCB format) 6. For the mechanical details of L-bracket and enclosed formats please consult sales office Pin Chart PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PD40-10 MODEL PD40-12 OUTPUT OUTPUT OUTPUT RETURN RETURN RETURN PD40-13 PD40-14 #1 #1 #1 PD40-23 PD40-24 OUTPUT OUTPUT OUTPUT COMMON COMMON N/C #2 #1 #1 RETURN RETURN PD40-25 PD40-30 PD40-31 OUTPUT OUTPUT OUTPUT COMMON COMMON OUTPUT PD40-32 PD40-39 PD40-33 #2 #1 #1 RETURN RETURN #3 Your dependable power partner – www.powerbox.com.au 123 OPEN FRAME & ENCLOSED PD Series 4 0 - 1 1 0 W AT T S W I D E I N P U T Selection Table PD65 SERIES (65W) MODEL NUMBER OUTPUT #1 OUTPUT #2 OUTPUT #3 MAXIMUM OUTPUT POWER OUTPUT #4 VNOM. IMIN. IMAX. TOL. VNOM. IMIN. IMAX. TOL. VNOM. IMIN. IMAX. TOL. VNOM. IMIN. IMAX. TOL. PD65-10 5V 0A 10A 1% 50W PD65-12 12V 0A 5.5A 1% 65W PD65-13 15V 0A 4.5A 1% 65W PD65-14 24V 0A 3.0A 1% PD65-23 +5V 1A 6.0A 3% +12V 0.5A 3A 5% 65W PD65-24 PD65-25 +5V +5V 1A 1A 6.0A 6.0A 3% 3% +15V +24V 0.4A 0.3a 3A 2a 5% 5% 65W 65W PD65-30 +5V 1A 6.0A 3% +12V 0.5A 3A 5% -5V 0.1A 0.5A 10% 65W PD65-31 +5V 1A 6.0A 3% +12V 0.5A 3A 5% -12V 0.1A 0.5A 10% 65W PD65-32 +5V 1A 6.0A 3% +15V 0.4A 3A 5% -15V 0.1A 0.5A 10% 65W PD65-33 +5V 1A 6.0A 3% +15V 0.4A 3A 5% -12V 0.1A 0.5A 10% 65W PD65-39 +5V 1A 6.0A 3% +24V 0.3A 2A 5% -12V 0.1A 0.5A 10% PD65-40 +5V 1A 6.0A 3% +12V 0.5A 3A 5% -12V 0.1A 0.5A 10% 65W 65W -5V 0.1A 0.5A 10% 65W NOTES 1. All multi-output units may be operated at no load without damage. At no load, output tolerance increases to 10%. 2. Suffix codes for mechanical format and input range are as follows: PD65-XXYZ; “XX” is the model code from the above table, “Y” is the input range (L = 10–30VDC, M = 20–60VDC, H = 30–90VDC) and “Z” is the mechanical format (A = open PCB, B = L-bracket, C = enclosed), eg, PD65-31MC (20–60VDC input range, enclosed). 3. The models for 10–30VDC input range are suitable only for 70% of the above stated maximum output power. Technical Illustration PD65 ENCLOSED NOTES 1. Dimensions shown in inch (mm) 2. Tolerance 0.02 (0.5) maximum 3. Input connector mates with Molex housing 09-50-3031 and Molex 2878 series crimp terminal 4. Output connector mates with Molex housing 09-50-3081 and Molex 2878 series crimp terminal 5. Weight: 380 grams approx (PCB format) 6. For the mechanical details of L-bracket and enclosed formats please consult sales office Pin chart MODEL PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 OUTPUT OUTPUT OUTPUT RETURN RETURN RETURN RETURN COMMON OUTPUT OUTPUT N/C N/C RETURN RETURN #2 #2 COMMON COMMON OUTPUT OUTPUT OUTPUT N/C PD65-12 PD65-13 PD65-14 #1 #1 #1 #1 PD65-23 PD65-24 OUTPUT OUTPUT COMMON #1 #1 OUTPUT OUTPUT PD65-25 124 PIN 1 OUTPUT PD65-10 PD65-30 PD65-31 PD65-32 PD65-33 #1 #1 RETURN RETURN #2 #2 #3 PD65-39 OUTPUT OUTPUT OUTPUT COMMON COMMON OUTPUT OUTPUT OUTPUT PD65-40 #1 #1 RETURN RETURN #2 #2 #3 #4 4 0 - 1 1 0 W AT T S W I D E I N P U T Selection Table PD110 SERIES (110W) MAXIMUM OUTPUT #1 OUTPUT #2 OUTPUT #3 OUTPUT #4 MODEL OUTPUT NUMBER VNOM. IMIN. IMAX. TOL. VNOM. IMIN. IMAX. IPEAK TOL. VNOM. IMIN. IMAX. TOL. VNOM. IMIN. IMAX. TOL. POWER PD110-10 5V 0A 22A 3% 110W PD110-12 12V 0A 9.0A 2% 110W PD110-13 15V 0A 7.5A 2% 110W PD110-14 24V 0A 4.5A 2% 110W PD110-16 30V 0A 3.6A 2% PD110-23 +5V 0A 10A 3% +12V 0A 5A 9.0A 3% PD110-31 +5V 0A 10A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% PD110-32 +5V 0A 10A 3% +15V 0A 4A 7.5A 3% -15V 0A 1A 4% PD110-40 +5V 0A 10A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% -5V 0A 1A 4% 110W PD110-41 +5V 0A 10A 3% +15V 0A 4A 7.5A 3% -15V 0A 1A 4% +24V 0A 1A 4% 110W PD110-42 +5V 0A 10A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% +12V 0A 1A 4% 110W PD110-45-1 +5V 0A 10A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% +24V 0A 1.5A 10% 110W PD110-45-2 +5V 0A 10A 3% +24V 0A 3A 5.0A 3% -12V 0A 1A 4% +12V 0A 1A 4% 110W PD110-46 +5V 0A 10A 3% +15V 0A 4A 7.5A 3% -15V 0A 1A 4% -5V 0A 1A 4% 110W OPEN FRAME & ENCLOSED PD Series 110W 110W 110W 110W NOTES 1. Peak output current with 10% maximum duty cycle for less than 60 seconds. 2. PD110 “M” & “H” series are suitable only for 110W maximum at 20 CFM forced air cooling or 80W maximum at convection cooling. PD110 “L” series are suitable only for 90W maximum at 20 CFM forced air cooling or 70W maximum at convection cooling. 3. Suffix codes for input range, mechanical format and connector are as follows: PD110-X1X2X3X4X5, “X1X2” is the model code from the above table, “X3” is the input range (L = 10–20VDC, M = 18–36VDC, H = 36–72VDC), “X4” is the mechanical format (A = open PCB, B = L-bracket, C = enclosed) and “X5” is the input and output connector code (Blank + Molex KK type, T = miniature terminal block), eg, PD110–31MCT (18–36VDC input range, enclosed format and miniature terminals blocks). Technical Illustration PD110 Enclosed NOTES 1. Dimensions shown in inch (mm) 2. Tolerance 0.02 (0.5) maximum 3. Molex KK type connectors: Input connector mates with Molex housing 09-50-3051 and Molex 2878 series crimp terminal Output connector mates with Molex housing 09-50-3131 and Molex 2878 series crimp terminal 4. Miniature terminal blocks: Input terminals allow wires up to 2mm2 (AWG #14) Output terminals allow wires up to 2mm2 (AWG #14) 5. Weight: 640 grams (PCB format) 6. For the mechanical details of L-bracket and enclosed formats please consult sales office Pin chart MINI TERMINAL MOLEX CONNECTOR MODEL 1 1,2,3 2 4,5 3 6,7 4 8,9 PD110-10 PD110-13 PD110-16 PD110-23 PD110-12 PD110-14 OUTPUT #1 RETURN RETURN PD110-31 PD110-32 OUTPUT #1 OUTPUT #1 OUTPUT #1 COMMON RETURN COMMON RETURN COMMON RETURN COMMON RETURN COMMON RETURN COMMON RETURN PD110-40 PD110-41 PD110-42 PD110-45-1 PD110-45-2 PD110-46 10 5 11 12 6 13 OUTPUT #1 N/C N/C KEY N/C OUTPUT #2 OUTPUT #2 OUTPUT #2 N/C N/C N/C KEY N/C OUTPUT #3 OUTPUT #3 KEY N/C KEY OUTPUT N/C Your dependable power partner – www.powerbox.com.au 125