Freescale Semiconductor, Inc. Quarter 2, 2015 BR1569 Rev. 15 Applications Analog and Power Management Making embedded systems better with robust reliable performance Applications- Robust, Reliable, Performance GENERIC SYSTEM DIAGRAMS • MOTOR CONTROL — Regulates the speed, rotation, and torque of a motor • MOTION CONTROL — Governs the physical displacement movement, location, or position of a mechanical assembly, driven by an intermittent duty motor • STATIC LOAD CONTROL — Fully or partially powers-up the elements of a relatively constant load • POWERTRAIN AND ENGINE MANAGEMENT — Provides functionality for controlling and monitoring engine and transmission system loads • NETWORK COMMUNICATIONS — Provides device-to-device communication within a system • EMBEDDED MCU PLUS POWER — Provides an integrated single package solution with MCU, Voltage Regulation, Power Actuation, and LIN bus transceiver • BATTERY CHARGER — Provides high voltage accuracy over the full temperature range due to the different charging process • RADAR SYSTEMS — Provides long- and mid-range functionality, allowing automotive systems to monitor the environment around the vehicle to help prevent crashes • POWER MANAGEMENT — Converts system input power to the voltages and currents required by the MCU and DSP • BATTERY MANAGEMENT — Provides highest performance and accuracy, as well as exceptional configuration flexibility Applications Analog, Mixed-Signal, and Power Management MOTOR CONTROL GENERIC SYSTEM DIAGRAM Motor control is the function of regulating the speed, rotation, and torque of a motor. TYPICAL APPLICATIONS: LOOP CONTROL SCHEMA: POWER CONTROL SCHEMA: MOTOR TYPES: • Blowers • Speed • ON/OFF • DC 3-Phase Brushless • Fans • Torque/Current • PWM • Universal • Vacuums • Voltage • Linear • AC Induction • Pumps • Rotation (CW/CCW) • Volts/Hertz (V/f) • Switched Reluctance • Compressors • None (Open Loop) • Rotating Vector • Stepper • DC Brush Commutator • Phase Angle • Golf Carts • Scooters • Electric Wheelchairs • Electric Boats • Conveyors • Shakers • Vibrators • Mixers • Shredders • Winches • Elevators • Treadmills • Power Tools CONSIDER: CM0902 33399 33660 33661 33662 33663 33780 33897 33901/34901 POWER SUPPLY • S08 POWER MANAGEMENT • S12 • i.MX6/7 • Qorivva 32-bit INTER-MODULE COMMUNICATION SPI or PARALLEL CONTROL • Kinetis NETWORK TRANCEIVERS SYSTEM INPUT SIGNAL CONDITIONING 33910 33730 33911 33742 33989 33889 34700 33903/34903 34704 33904/34904 34713 33905/34905 34716 FS6407 34717 FS6408 34VR500 FS4409 PF0100 33907 PF0200 33908 PF3000 33909 MCU or DSP or ASSP CONTROLLER 2 POWER ACTUATION POWER ROTOR POSITION (optional) MOTOR FEEDBACK SIGNAL CONDITIONING 33793 33811 33972/34972 33975/34975 33978/34978 PT2000 33800 33810 33816 33879 33880 33882 33886 33887 33899 33931/34931 MECH ASSY 33HB2000 33HB2001 33GD3000 34GD3000 SB0400 SB0400 SB0401 34SB0410 34SB0800 33932/34932 33937/34937 33926 33996 33999 17510 17529 17533 17C724 12XS2 12XS3 12XS6 12XSB 12XSC 12XSF 24XS4 36XSD 33793 33811 33972/34972 33975/34975 33978/34978 See “Embedded MCU Plus Power Generic System Diagram” on page 7. Analog, Mixed-Signal, and Power Management Applications MOTION CONTROL GENERIC SYSTEM DIAGRAM Motion control is the function of governing the physical displacement, movement, location, or position of a mechanical assembly driven by an intermittent duty motor. TYPICAL APPLICATIONS: • Printer Paper Handler • CNC Machining • Conveyors • Robotics • Shakers • Scanners POWER CONTROL SCHEMA: • Rotation (CW/ CCW) • ON/OFF • DC Brush Commutator • PWM • Brushless DC • Linear • Stepper • Step Count • Stepper (Pulse & Hold) • Linear • Hard Automation • Consumer Portable Products • Position • Power-Assisted • Digital Cameras • Operator Controls • Printers • Operator (Open Loop) • Process Controls • Office Equipment • Autopilots • Industrial Controller • Guidance/Steering • Force • Controls • Spot Welding • Servos and Radio • Fluid Coating • Controls • Flight Simulator • Antenna Rotors • Temperature Control • Dish Positioners • Brake Pressure • Power Adjustable • Laser Cutting • Beds • Bottle Moulding • Remote Pan and Tilt • Filling Pressure • HVAC Mix Louvers MOTOR TYPES: LOOP CONTROL SCHEMA: • Solenoid • Servos • Mounts CONSIDER: CM0902 33399 33660 33661 33662 33663 33780 33897 33901/34901 POWER SUPPLY • S08 POWER MANAGEMENT • S12 • i.MX6/7 • Qorivva 32-bit INTER-MODULE COMMUNICATION SPI or PARALLEL CONTROL • Kinetis NETWORK TRANCEIVERS SYSTEM INPUT 33730 33910 33742 33911 33889 33912 33903/34903 33989 33904/34904 34700 33905/34905 34704 FS6407 34713 FS6408 34716 FS4409 34717 33907 34VR500 33908 MCU or DSP or ASSP CONTROLLER SIGNAL CONDITIONING See “Embedded MCU Plus Power Generic System Diagram” on page 7. POWER ACTUATION POWER ROTOR POSITION (optional) 33931/34931 33932/34932 33937/34937 33996 33999 34933 SB0400 SB0401 33HB2000 33HB2001 33GD3000 34GD3000 17510 17529 17533 17C724 12XS2 12XS3 12XS6 12XSB 12XSC 12XSF 24XS4 36XSD MOTOR/ PUMP FEEDBACK SIGNAL CONDITIONING 33793 33811 33972/34972 33975/34975 33978/34978 PT2000 SB0410 SB0800 33800 33810 33816 33879 33880 33882 33886 33887 33899 33926 MECH ASSY 33793 33811 33972/34972 33975/34975 3 Applications Analog, Mixed-Signal, and Power Management STATIC LOAD CONTROL GENERIC SYSTEM DIAGRAM Static load control is the function of fully or partially powering-up the elements of a relatively constant load. TYPICAL APPLICATIONS: LOOP CONTROL SCHEMA: • Security Systems • Current • HVAC POWER CONTROL SCHEMA: STATIC LOAD TYPES: • ON/OFF • Heating Elements • Incandescent Lamps • Water Heaters • Voltage • PWM • LEDs/Lasers • Charging Systems • Sensor Feedback • PFM • Lighting Displays • Limit Switch (Bang-Bang) • Linear • Ultrasonic Transducers • Phase Angle • Piezo Transducers • Score Boards • None (Open Loop) • Irrigation Control • Induction Coils • Sirens/Horns/Bells • Programmable Thermostats • Gaming Machines • Industrial Controls • Automotive Body Electronics • Large Building Automation • White Goods Appliances • Automotive Safety Systems • LED Backlighting/Displays CONSIDER: • S08 33CM0902/34CM0902 33399 33660 33661 33662 33663 33780 33897 33901/34901 POWER SUPPLY POWER MANAGEMENT • S12 • i.MX6/7 • Qorivva 32-bit • Kinetis INTER-MODULE COMMUNICATION NETWORK TRANCEIVERS SYSTEM INPUT SIGNAL CONDITIONING 33910 33730 33911 33742 33912 33889 33903/34903 33989 33904/34904 34700 33905/34905 34704 34VR500 FS6407 PF0100 FS6408 PF0200 FS4409 PF3000 33907 33908 33909 PARALLEL I/O POWER PARALLEL ACTUATION I/O MCU or DSP or ASSP CONTROLLER SPI I/O SPI I/O 33800 33810 33811 33879 33880 33882 33931/34931 33932/34932 33996 33999 34844 12XS2 12XS3 12XS6 12XSB 12XSC 12XSF 24XS4 36XSD POWER ACTUATION POWER ACTUATION POWER ACTUATION FEEDBACK SIGNAL CONDITIONING 33793 33811 33972/34972 33975/34975 33978/34978 4 33793 33811 33972/34972 33975/34975 See “Embedded MCU Plus Power Generic System Diagram” on page 7. Analog, Mixed-Signal, and Power Management Applications POWERTRAIN AND ENGINE MANAGEMENT SYSTEM DIAGRAM These components represent devices that are designed to function in the automotive environment. They provide the functionality needed for controlling and monitoring engine and transmission systems loads and inputs. The functions available range from alternator voltage regulator control to Low-side switches, H-Bridge drivers, MOSFET/IGBT Pre-drivers, switch and solenoid monitoring, and more. TYPICAL APPLICATIONS: LOOP CONTROL SCHEMA: POWER CONTROL SCHEMA: LOAD TYPES: • Marine Engine • Current • ON/OFF • Heating Elements • Boat Motor • Voltage • PWM • LEDs/Lasers • Jet Ski Engine • Sensor Feedback • PFM • Ultrasonic • ATV / Motorcycle Engine • Linear • Transducers • Industrial Engines • Limit Switch (Bang-Bang) • Phase Angle • None (Open Loop) • Piezo Transducers • Heavy Equipment • Incandescent Lamps • Induction Coils • Automobile Engines (2-12 cylinders) • Sirens/Horns/Bells Powertrain Controller Loads Analog / Digital Inputs Main MCU Gasoline and Diesel 33811 33975/34975 33978/34978 Cam Position Clutch/Break Speed CONSIDER: Timed Inputs • Kinetis Gasoline and Diesel • S12XE Accelerator • S12P Mass Air Flow • S12XS Battery • Qorivva Temperatures Oxygen Sensors 33811 33975/34975 33978/34978 912_637 9Z1_638 Gasoline Only Throttle Position Signal Monitoring and Conditioning Crank Speed Power DMA Injector Drivers Ext Bus COM Ignition Plugs (up to 12) Diesel Only Glow Plugs (up to 12) Gasoline Only Throttle Control Diesel Only EGR Positioner, Valves Control Flash Loads Safety Micro HC08, S08, S12 Power Management IC COM ICs HS CAN LIN FlexRay Ethernet Gasoline and Diesel Output Drivers Relays Tachometer Counter Oxygen Heaters 33907 33908 33730 33909 Fuel Pump Dashboard Lamps Recirculation Valves Knock Sensor Gasoline Only Diesel Only Cylinder Pressure CAN BUS Rail Pressure Injectors (up to 12) Gasoline Only Ignition Pre-drivers H-Bridge Drivers Timers eTPU + eMOS Gasoline and Diesel 912_P812 912_S812 912_637 9Z1_638 33810 33811 33812 33813 33814 33816 912_P812 912_S812 PT2000 12XS2 12XS3 12XS6 12XSB 12XSC 12XSF 24XS4 36XSD 33800 33810 33812 33937/34937 Cam Control Fuel Tank Valves Intake Control Diesel Only 33899 33926 33931/34931 33932/34932 Fan Control Rail Pressure Control 5 Applications Analog, Mixed-Signal, and Power Management NETWORK COMMUNICATIONS SYSTEM DEVICES Network communication provides information between two or more devices in a system. TYPICAL APPLICATIONS: COMMUNICATIONS SCHEMA: • Aircraft Systems • Bidirectional • Antenna Controllers • Combined Power & Signaling Error Detection • Appliances • Automotive Body Electronics • Fault Tolerant • Automotive Safety Systems • Full/Half Duplex • Conveyors • Predictive • Elevators • Gaming Machines • Single Ended/ Differential • Heating & Cooling • Single/Multi Master • Irrigation Control • Single/Multi Slave • Lighting • Timing Critical • Machinery/Robotics • Voltage/Current Signaling • Hi/Med/Low Speed • Score Boards • Security Systems • Vending Machines • Watercraft Systems • Water Heaters DSI2 Sensor Interface 33784 DSI 2.02 Bus Slave Pressure Sensor 33784 DSI 2.02 Bus 4X Accelerometer CONSIDER: • S08 • S12 • Qorivva 32-bit • Kinetis Remote Modules ISO9141 Bus Remote Modules LS CAN Bus 33889 LIN Bus DSI Bus 33793 DSI Bus 2X 33660 33897 HS CAN Bus Slave DBus Master 33780 33790 SW CAN Bus Remote Modules Remote Modules 6 PSI5 Bus Master 33789 DSI2 Bus Master 33781 Remote Modules Pressure Sensor 33742 33901 33903 33904 33905 33907 33908 33989 CM0902 33661 33662 33663 33903 33905 33907 33908 33909 33910 33911 33912 MCU SPI LOGIC ISO9141 LOGIC VDD,VIO CAN LOGIC LIN LOGIC DSI Sensor Interface 33793 Accelerometer Analog, Mixed-Signal, and Power Management Applications EMBEDDED MCU PLUS POWER GENERIC SYSTEM DIAGRAM Motor control is the function of regulating the speed, rotation and torque of a motor. TYPICAL APPLICATIONS: LOOP CONTROL SCHEMA: POWER CONTROL SCHEMA: MOTOR TYPES: • Blowers • Speed • ON/OFF • DC 3-Phase Brushless • Fans • Torque/Current • PWM • Universal • Pumps • Voltage • Linear • 2-Phase Stepper • Power Seats • Rotation (CW/CCW) • Volts/Hertz • Power Windows • None (Open Loop) • DC Brush Commutator • Power Door Locks • HVAC Doors/Vents • Power Sunroof • Side-view Mirrors • Keypad • Light Leveling • Adaptive Lighting 33CM0902/34CM0902 33399 33660 33661 33662 33663 33901/34901 908E621 908E622 908E624 908E625 908E626 912_634 912_637 9Z1_638 EMBEDDED: • S12 MagniV • S12Z INTER-MODULE COMMUNICATION • S12 NETWORK TRANCEIVERS SYSTEM INPUT SIGNAL CONDITIONING POWER LOADS POWER ACTUATION LIN P/L EMBEDDED MCU + POWER CONTROLLER POWER SUPPLY 33793 33811 33972/34972 33975/34975 33978/34978 ROTOR POSITION (optional) MOTOR CURRENT (optional) MOTOR FEEDBACK SIGNAL CONDITIONING MECH ASSY 33793 33811 33972/34972 33975/34975 33978/34978 7 Applications Analog, Mixed-Signal, and Power Management BATTERY CHARGER Portable Navigation Devices (PNDs) are expanding their reach to be embedded in everything from smartphones to auto infotainment systems. Battery Charger provides flexible solutions to develop innovative navigation devices with wide range of features. TYPICAL APPLICATIONS: CHARGE CURRENT TYPES: • Internet of Things (IoT) • Constant Charge Current • Handheld consumer devices • Constant Charge Voltage • Wearable market • Pre-charge • PoS terminals • Trickle • Medical portable equipment • Consumer tablets BC3770 Application USB Battery Charger MCU 8 Battery Analog, Mixed-Signal, and Power Management Applications RADAR SYSTEMS 77 GHz radar systems support adaptive cruise control, pre-crash protection and collision warning systems with and without automatic steering and braking intervention. In a collision warning system, the radar chipset can detect and track objects, automatically adjusting the vehicle’s speed and distance in response to the traffic ahead and triggering a driver warning of an imminent collision and initiate emergency braking intervention. TYPICAL APPLICATIONS: Automotive Industrial • Adaptive Cruise Control (ACC) • Robotics • Blind-spot Detection (BSD) • Industrial Automation precision monitor • Emergency Braking • Industrial Surveillance and Security Systems • Forward Collision Warning (FCW) • Millimeter Wave Backhaul Systems • Headway Alert • Mitigation and Brake Support • Pre-crash Detection • Industrial Safety • Precision Distance Measurement Systems • Rear Collision Protection (RCP) • Stop & Go MR2001RVK Receiver CONSIDER: • Qorivva 32-bit MPC577xK MCU MR2001TVK Voltage Controlled Oscillator Transmitter MR2001VVK XTAL 9 Applications Analog, Mixed-Signal, and Power Management POWER MANAGEMENT GENERIC SYSTEM DIAGRAM Embedded power regulation is the function of converting system input power to the voltages and currents required by the MCU or DSP as well as DDR (Double Data Rate) memory. TYPICAL APPLICATIONS: LOOP CONTROL SCHEMA: POWER CONTROL SCHEMA: • Industrial Controls • Voltage Mode Feedback • Linear Regulators • Current Mode Feedback • Battery Management • Embedded Control Modules • Consumer Appliances • Switching Regulators • Marine Electronics • Engine/Generator Control • Network Equipment • Set-Top Box • Battery Chargers • Travel Chargers INPUT FILTERING INTER-MODULE COMMUNICATION CONSIDER: • S08 • S12 • i.MX6/7 10 NETWORK TRANCEIVERS 33730 33742 33889 33903/34903 33904/34904 POWER MANAGEMENT (POWER CONVERSION and REGULATION) 33905/34905 33910 33911 33912 VDD1 VDD2 VDDn PARALLEL I/O SPI I/O 33399 33660 33661 33662 33663 33897 33901/34901 CM0902 33989 34713 34716 34717 VR500 PF0100 PF0200 PF3000 SPI I/O MCU or DSP Analog, Mixed-Signal, and Power Management Applications BATTERY MANAGEMENT GENERIC SYSTEM DIAGRAM For lead acid batteries, an intelligent sensor combines the requirements of accurate measurement sensing with logic capability to bring decision making to the sensing solution. TYPICAL APPLICATIONS: For mission critical battery operations: Automotive LOOP CONTROL SCHEMA: POWER CONTROL SCHEMA: • Voltage • Linear Regulators • Temperature Current • 12 V Lead Acid, 14V Li-Ion • HV Battery Junction Box • Multi-Battery Applications Trucks and Utilities • 24 V Lead Acid Industrial BATTERY TYPES: • Energy Storage Systems (ESS) • UPS • 12 V Lead Acid Battery • Industrial Automation precision monitor • 14 V Li-Ion Battery • Lead Acid Multi-battery • eBike • Power tools Network Equipment • Set-Top Box • Battery Chargers • Travel Chargers High-voltage Battery Cells Control 33903 33905 33907 33908 FS6407 FS6408 FS4409 Li-Ion Cells Supervising Circuitry 912_637 9Z1_638 12 V Battery Sensor CONSIDER: Battery Junction Box • S12G • MPC5748G • MPC56xB Comm. and Isolation MCU SBC 33903 33905 33907 33908 FS6407 FS6408 FS4409 High-voltage Battery Multi-Cells Li-Ion SBC MCU Pumps, Heater, Sensors 12 V Battery Signal Inputs 3-Phase Driver Temperature Switches MCU 33937 SBC High-voltage Battery Thermal Control 33903 33905 33907 33908 33909 FS6407 FS6408 FS4409 11 Applications Analog, Mixed-Signal, and Power Management ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL CONDITIONING, AND RADAR Freescale Part Number 12XS2 Description 12 V Multipurpose Low RDS(on) eXtreme Switch Product 12XS3 12 # of outputs RDS(on) (mOhm) MC33981 Single MC33982 Single 1 X 2.0 MC33984 Dual 2 X 4.0 MC33988 1 X 4.0 Dual 2 X 8.0 12 V Automotive Exterior Lighting Multichannel eXtreme Switch Product 12XS6 Main Characteristics # of outputs RDS(on) (mOhm) MC06XS3517 Penta 3 X 6.0 2 X 17.0 MC07XS3200 Dual 2 X 7.0 MC09XS3400 Quad 4 X 9.0 MC10XS3412 Quad 2 X 10.0 2 X 12.0 MC10XS3425 Quad 2 X 10.0 2 X 25.0 MC10XS3435 Quad 2 X 10.0 2 X 35.0 MC10XS3535 Penta 3 X 10.0 2 X 35.0 MC15XS3400 Quad 4 X 15.0 MC35XS3400 Quad 4 X 35.0 MC35XS3500 Penta 5 X 35.0 The eXtreme switch MC12XS2 family consists of very low RDS(on) devices in single or dual high-side configuration to replace electromechanical relays or discrete devices, in power management applications and DC motor control. The devices are designed for harsh environments, and it includes self-recovery features. The devices are suitable for loads with high inrush current, as well as motors and all types of resistive and inductive loads. The eXtreme Switch Gen3 12 V devices are SPI-Controlled smart high-side switches providing diagnostics for the switch, light source and wiring harness, as well as comprehensive fault management and control of the loads without complex software. The devices use a programmable multi-step latched overcurrent shutdown protection. External Automotive Lighting Multichannel Scalable The Gen4 eXtreme Switch is the latest achievement in automotive lighting drivers. eXtreme Switch It belongs to an expanding family to control and diagnose bulbs and also the light emitting diodes (LEDs) with enhanced diagnostic precision. It combines flexibility RDS(on) through daisy chainable SPI at 5.0 MHz, extended digital and analog feedbacks, Product # of outputs (mOhm) safety and robustness. Its low RDS(on) and high integration allows power and space saving at the module level. It is also compliant with an Asil-B module design. This MC07XS6517 Penta 3 X 7.0 family is packaged in a Pb-Free power-enhanced SOIC package with exposed 2 X 17.0 pad, which is ELV compliant. MC08XS6421 Quad 2 X 8.0 2 X 21.0 MC10XS6200 Dual 2 X 10.0 MC10XS6225 Dual 1 X 10.0 1 X 25.0 MC10XS6325 Triple 2 X 10.0 1 X 25.0 MC17XS6400 Quad 4 X 17.0 MC17XS6500 Penta 5 X 17.0 MC25XS6300 Triple 3 X 25.0 MC40XS6500 Penta 5 X 40.0 Analog, Mixed-Signal, and Power Management Applications ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL CONDITIONING, AND RADAR (continued) Freescale Part Number 24XS4 Description 24 V Multipurpose Low RDS(on) Intelligent eXtreme Switch Product 12XSB # of outputs Dual 2 X 6.0 MC10XS4200 Dual 2 X 10.0 MC20XS4200 Dual 2 X 20.0 MC22XS4200 Dual 2 X 22.0 MC50XS4200 Dual 2 X 50.0 12 V Industrial Multipurpose Low RDS(on) eXtreme Switch # of outputs RDS(on) (mOhm) MC34981 Single 1 X 4.0 MC34982 Single 1 X 2.0 MC34984 Dual 2 X 4.0 MC34988 Dual 2 X 8.0 12 V External Industrial Lighting Multichannel eXtreme Switch Product # of outputs These devices are part of a 24 V high-side switch product family with integrated control, and a high number of protective and diagnostic functions. It is designed for truck, bus, and 24 V based transportation systems. The low RDS(on) channels can control different load types; lamps, solenoids, or DC motors. Control, device configuration, and diagnostics are performed through a 16-bit serial peripheral interface (SPI), allowing easy integration into existing applications. RDS(on) (mOhm) MC06XS4200 Product 12XSC Main Characteristics RDS(on) (mOhm) MC06XSC517 Penta 3 X 6.0 2 X 17.0 MC07XSC200 Dual 2 X 7.0 MC09XSC400 Quad 4 X 9.0 MC10XSC412 Quad 2 X 10.0 2 X 12.0 MC10XSC425 Quad 2 X 10.0 2 X 25.0 MC10XSC435 Quad 2 X 10.0 2 X 35.0 MC10XSC535 Penta 3 X 10.0 2 X 35.0 MC15XSC400 Quad 4 X 15.0 MC35XSC400 Quad 4 X 35.0 MC35XSC500 Penta 5 X 35.0 The 12 V eXtreme Switch family consists of very low RDS(on) devices in single high-side configuration, to replace electromechanical relays or discrete devices in industrial power management applications and DC motor control. The devices are designed for harsh environments, and include self-recovery features. The devices are suitable for loads with high inrush current, as well as motors and all types of resistive and inductive loads. The eXtreme switch devices are SPI-controlled smart high-side switches for Industrial applications, providing diagnostics, as well as comprehensive fault management and control of the loads without complex software. The devices use a programmable multi-step latched overcurrent shutdown protection. This technique is preferable to the current limit method because it minimizes the thermal stress within the device during an overload condition, greatly reducing the junction temperature rise and vastly improving reliability. 13 Applications Analog, Mixed-Signal, and Power Management ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL CONDITIONING, AND RADAR (continued) Freescale Part Number 12XSF Description External Industrial Lighting Multichannel Scalable eXtreme Switch Product 36XSD # of outputs RDS(on) (mOhm) MC07XSF517 Penta 3 X 7.0 2 X 17.0 MC08XSF421 Quad 2 X 8.0 2 X 21.0 MC10XSF200 Dual 2 X 10.0 MC10XSF225 Dual 1 X 10.0 1 X 25.0 MC10XSF325 Triple 2 X 10.0 1 X 25.0 MC17XSF400 Quad 4 X 17.0 MC17XSF500 Penta 5 X 17.0 MC25XSF300 Triple 3 X 25.0 MC40XSF500 Penta 5 X 40.0 36 V Multipurpose Industrial Low RDS(on) Intelligent eXtreme Switch Product 14 Main Characteristics # of outputs RDS(on) (mOhm) MC06XSD200 Dual 2 X 6.0 MC10XSD200 Dual 2 X 10.0 MC16XSD200 Dual 2 X 16.0 MC22XSD200 Dual 2 X 22.0 MC50XSD200 Dual 2 X 50.0 The eXtreme switch products are the latest achievement in DC motors and industrial lighting drivers. They belong to an expanding family to control and diagnose various types of loads, such as incandescent bulbs or light emitting diodes (LEDs), with enhanced precision. The products combine flexibility through daisy chainable SPI at 5.0 MHz, extended digital and analog feedbacks, which supports safety and robustness. This new generation of Freescale's high-side switch products family facilitates electronic control unit designs supported by the use of compatible MCU software and PCB footprints, for each device variant. Freescale's family of intelligent, dual high-side eXtreme switches for 36 V systems offers devices with current capability ranging from one to 12 A DC that are fully compatible in footprint and software within the PQFN sub family. Each output can be programmed to be used for any kind of loads, including lamps, LEDs, motors or solenoids. This allows customers to design a flexible module which can become specific and optimized for a given application through software. Freescale's 36 V eXtreme switch solution provides robust design, intelligence and safety needed for industrial applications up to 36 V supply voltage. 33399 Local Interconnect Network (LIN) Physical Interface LIN Transceiver with Wake and Enable Inputs, Inhibit Output 33660 ISO K Line Serial Link Interface A serial link bus interface device designed to provide bi-directional half-duplex communication interfacing in automotive diagnostic applications. It is designed to meet the automotive diagnostic systems ISO9141 specification. 33661 Enhanced LIN Transceiver Selectable Slew Rate for Operations at 10, 20, and 100 kbps; Bus Short to Ground Fail-safe; Excellent EMC Behavior 33662 LIN 2.1 / SAEJ2602-2, LIN Physical Layer Transceiver The 33662s are physical Layer components dedicated to automotive LIN sub-bus applications. They features either a 20 kbps baud rate or a 10 kbps baud rate. The 33662s integrate fast baud rate for test and programming modes, and provide excellent ESD robustness, immunity against disturbance, and radiated emission performance. 33663 LIN 2.1 / SAEJ2602-2 Dual LIN Physical Layer The 33663 product line integrates two physical layer LIN bus dedicated to automotive LIN sub-bus applications. The MC33663LEF and MC33663SEF devices offer normal baud rate (20 kbps) and the MC33663JEF slow baud rate (10 kbps). Both devices integrate fast baud rate (above 100 kbps) for test and programming modes. 33664 Isolated Network High-speed Transceiver Physical Layer (TPL) The 33664TL is a transceiver physical layer transformer driver designed to conveniently interface a microcontroller to a high-speed isolated communication network. Analog, Mixed-Signal, and Power Management Applications ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL CONDITIONING, AND RADAR (continued) Freescale Part Number Description Main Characteristics 33730 Switch Mode Power Supply with Multiple Linear Regulators The 33730 is a multiple output power supply integrated circuit for automotive applications. The integrated circuit (IC) incorporates a switching regulator which operates over a wide input voltage range from +4.5 V to +26.5 V. The step-down switching regulator uses a fixed frequency PWM voltage mode control. It has a 3.5 A current limit (typical) and the slew-rate is adjustable via a control pin to reduce switching noise. The linear regulators can be configured either as two normal mode regulators (VDD3, VDDL) and one standby regulator (VKAM), or as one normal mode linear regulator (VDDL) and two standby regulators (VKAM and VDD3 Standby). 33742 System Basis Chip with Enhanced High-speed CAN Transceiver SBC, Dual VREG, Enhance HS CAN with Bus Failure Diagnostic Capability, 4 Wake-up Inputs 33771 Battery Cell Controller IC (BCC) The 33771 is a lithium ion Battery Cell Controller IC designed for automotive applications, such as hybrid electric (HEV) and electric vehicle (EV) systems as well as industrial applications, such as energy storage systems (ESS) and uninterruptible power supply (UPS) systems. 33780 Dual DBUS Master with Differential Drive and Frequency Spreading The 33780 is a master device for two differential DBUS buses. It contains the logic to interface the buses to a standard serial peripheral interface (SPI) port and the analog circuitry to drive data and power over the bus as well as receive data from the remote slave devices. 33781 Quad DBUS Master with Differential Drive and Frequency Spreading The 33781 is a master device for four differential DBUS buses. It contains the logic to interface the buses to a standard serial peripheral interface (SPI) port and the analog circuitry to drive data and power over the bus as well as receive data from the remote slave devices. 33784 Distributed System Interface (DSI) Sensor Interface 2-Channel, 10-Bit A-to-D, 5.0 V Regulated Output, DSI Bus, 3 Configurable I/O, Fault Tolerant, High Drive Output 33789 Airbag System Basis Chip (SBC) with Power Supply and PSI5 Sensor Interface The 33789 offers an industry standard serial peripheral interface (SPI) and four PSI5 master interfaces. The 33789 has a dedicated safing state machine that complements an airbag’s MCU hardware/ software safing approach. Also included are a diagnostic - self protection capability. 33790 Two-Channel Distributed System Interface (DSI) Physical Interface Device The 33790 is a dual channel physical layer interface IC for the Distributed System Interface (DSI) bus. It is designed to meet automotive requirements. It can also be used in non automotive applications. It supports bidirectional communication between slave and master ICs. Some slave devices derive a regulated 5.0 V from the bus, which can be used to power sensors, thereby eliminating the need for additional circuitry and wiring. 33793 Distributed System Interface (DSI) Share Interface Sensor 4-Channel, 8-Bit A-to-D, 5.0 V Regulated Output, DSI Bus, Configurable I/O, Fault Tolerant 33800 Engine Control Integrated Circuit (IC) 16 Channel low-side and gate driver IC. Provides 8 low-side switches, 2 constant current low-side switches, and 6 external MOSFET gate drivers. 33810 Eight Channel Ignition and Injector Driver 8 Channel load driver. Comprised of 4 low-side output drivers and 4 external MOSFET, or IGBT gate drivers 33811 Solenoid Monitor Integrated Circuit (IC) A 5 Channel solenoid monitor IC. Provides verification of solenoid operation by monitoring the solenoid current waveform. 33812 Multifunction Ignition and Injector Driver Three low-side drivers, one pre-driver, a +5.0 V voltage pre-regulator, an MCU watchdog circuit and a ISO 9141 K-Line interface, for single/ dual cylinder engine control. Programmable Solenoid Controller The PT2000 is a SMARTMOS programmable gate driver IC for precision solenoid control applications, which makes the component very flexible and relieves the main microcontroller from the heavy task of the actuator control. 33879 Configurable Octal Serial Switch with Open Load Detect Current Disable An 8-output hardware-configurable, high-side/low-side switch, with a 16-bit serial (SPI) input control. 0.75 Ohm RDS(on) 33880 Configurable Eight Output Control Switch with SPI (0.55 Ohm RDS(on)) 8-output hardware configurable high-side/low-side switch with 8-bit serial input control 33882 Output Switch with SPI and Parallel Input Control (0.3 Ohm RDS(on)). Contains 6 Low-side Switches. Fully protected, 6 x 1.0 a (SPI and parallel control) + 2 x 30 ma (parallel control) switches, and SPI diagnostics 33886 H-Bridge Driver (5.0 A H-Bridge) Monolithic H-Bridge ideal for fractional horsepower DC motor and bidirectional thrust solenoid control PT2000 15 Applications Analog, Mixed-Signal, and Power Management ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL CONDITIONING, AND RADAR (continued) Freescale Part Number Description Main Characteristics 33887 H-Bridge with Load Current Feedback (5.0 A H-Bridge) Supports forward, reverse, freewheeling, 10 kHz PWM, status, disable inputs, and load current feedback 33889 System Basis Chip with Low Speed Fault Tolerant CAN 2x regulator, high-side switched power, LS CAN, SPI, wake-up inputs, window watchdog, reset, and interrupt 33897 Single Wire CAN Transceiver Carrier sense multiple access/collision resolution (CSMA/CR) data link, and bus activity sleep/wake-up 33899 Programmable H-Bridge Power Integrated Circuit (IC) Programmable H-Bridge controller for a DC motor or two solenoids. Parallel inputs as well as a SPI interface provided control and diagnostic reporting, including PWM’ed outputs. Dual CAN High-Speed Transceiver The CM0902 Dual CAN High-speed physical layer is Freescale's cost-effective product designed to target standard CAN High-speed applications requiring multiple transceivers. High-Speed CAN Transceiver The 33/34901 is the latest standard cost-effective product designed to target CAN FD (flexible data) operation up to 2 Mbps and used to convert digital protocol information into analog CAN communication. The device supports long-length CAN node interconnects for industrial applications. System Basis Chip Gen2 with High-Speed CAN and LIN Interface The 33/34903 is the second generation family of System Basis Chips which combine several features and enhance present module designs. The device works as an advanced power management unit for the MCU and additional integrated circuits such as sensors, CAN transceivers. It has a built-in enhanced high-speed CAN interface (ISO11898-2 and -5), and may include zero, one or two LIN 2.0 interfaces System Basis Chip Gen2 with High-speed CAN The 33/34904 is the second generation family of System Basis Chips which combine several features and enhance present module designs. The device works as an advanced power management unit for the MCU and additional integrated circuits such as sensors, CAN transceivers. It has a built-in enhanced high-speed CAN interface (ISO11898-2 and -5). System Basis Chip Gen2 with High-speed CAN and LIN Interface The 33/34905 is the second generation family of System Basis Chips which combine several features and enhance present module designs. The device works as an advanced power management unit for the MCU and additional integrated circuits such as sensors, CAN transceivers. It has a built-in enhanced high-speed CAN interface (ISO11898-2 and -5), and may include one or two LIN 2.0 interfaces. System Basis Chip (SBC) with LIN Transceiver Low End SBC device combines a 5.0 V, 60 mA LDO, LIN transceiver, a high-side switch output, one analog/logic input and a watchdog timer, with SPI and PWM control System Basis Chip (SBC) with LIN Transceiver Medium End SBC device combines a 5.0 V, 60 mA LDO, LIN transceiver, one high-side switch output, two low-side switch outputs, two analog/logic inputs and a watchdog timer, with SPI and PWM control. System Basis Chip (SBC) with LIN Transceiver High End SBC device combines a 5.0 V, 60 mA LDO, a switched 5.0 V output, LIN transceiver, two high-side switch outputs, two low-side switch outputs, four analog/ logic inputs and a watchdog timer, with SPI and PWM control. 33926 5.0 A throttle Control H-Bridge Power Integrated Circuit (IC) This device drives a DC motor or 2 solenoids for actuator control. Parallel input control of outputs and fault reporting. 33931 5.0 A Throttle Control H-Bridge The 33/34931 is a monolithic H-Bridge power IC in a robust thermally enhanced package. It is designed for automotive electronic throttle control, but is applicable to any industrial low-voltage DC servo motor control application. 5.0 A Throttle Control H-Bridge (Dual) The 33/34932 is a monolithic H-Bridge power IC in a robust thermally enhanced package. The 33/34932 has two independent monolithic H-Bridge Power ICs in the same package. They are designed for automotive electronic throttle control, but is applicable to any industrial low-voltage DC servo motor control application. Three Phase Field Effect Transistor Pre-driver The 33/34937 is a field effect transistor (FET) pre-driver designed for three phase motor control and similar applications. The IC contains three high-side FET predrivers and three low-side FET pre-drivers.Three external bootstrap capacitors provide gate charge to the high-side FETs. 33CM0902 34CM0902 33901 34901 33903 34903 33904 34904 33905 34905 33910 34910 33911 34911 33912 34912 34931 33932 34932 33937 34937 16 Analog, Mixed-Signal, and Power Management Applications ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL CONDITIONING, AND RADAR (continued) Freescale Part Number 33972 Description Main Characteristics Multiple Switch Detection Interface with Suppressed Wake-up Multiple switch detection interface with suppressed wake-up designed to detect closing and opening of up to 22-switch contacts. Multiple Switch Detection Interface with Suppressed Wake-up and 32 mA Wetting Current 22 inputs contact monitoring (14 GND, 8 configurable), and selectable wake-up on change of state. Configurable IO - Multiple Switch Detection Interface The MC33978/MC34978 configurable I/O is an analog switch interface used to translate22 I/Os onto a single MCU SPI bus, with low power auto-wake modes and programmable wetting currents. 33989 System Basis Chip with High-speed CAN 2x regulator, high-side switched power, SPI, wake-up inputs, window watchdog, interrupt, and CAN transceiver 33996 16 Output Switch with SPI Control. (0.55 Ohm RDS(on)) A 16-output low-side switch with a 24-bit serial input control (SPI), for control and diagnostics. Ouputs are current limited (0.9 to2.5 A). Output voltage clamp of +50 V during inductive switching. selectable PWM control of outputs. Protection circuits 33999 16 Output Switch with SPI and PWM Control (0.55 Ohm RDS(on)) A 16-output low-side switch with a 24-bit serial control (SPI) The SPI provides both input control and diagnostic readout. Eight parallel inputs also provide direct pulse width modulation (PWM) control of eight dedicated outputs. Reset input. 77 GHz Radar Transceiver Chipset The MR2001 is a high-performance 77 GHz radar transceiver chipset scalable for multi-channel operation enabling a single radar platform with electronic beam steering and wide field of view to support long-range radar (LRR), mid-range radar (MRR) and short-range radar (SRR) applications. 34671 600 mA High Input Voltage Charger for Single-cell Li-Ion and Li-Polymer Batteries The MC34671 is a cost-effective fully integrated battery charger for Li-Ion or LiPolymer batteries. It tolerates an input voltage up to 28 V, which eliminates the input over-voltage protection circuit required in handheld devices. A charge cycle includes trickle, constant-current (CC) and constant-voltage (CV) charge modes. 34673 1.2 A High Input Voltage Charger for Single Cell Li- The MC34673 is a cost-effective fully-integrated battery charger for Li-Ion or LiIon and Li-Polymer Batteries Polymer batteries. It tolerates an input voltage up to 28 V, which eliminates the input over-voltage protection circuit required in handheld devices. A charge cycle includes trickle, constant-current (CC) and constant-voltage (CV) charge modes. 34674 High Input Voltage Travel Charger for Single Cell Li-Ion and Li-Polymer Batteries The MC34674 is a fully integrated single-cell Li-Ion and Li-Polymer battery charger optimized for travel charger applications. The few external components required include a dual color LED for charge status indication, a negative temperature coefficient (NTC) thermistor circuit for setting the charge temperature window, and two decoupling capacitors. The MC34674 tolerates an input voltage up to 28 V, which allows low cost AC/DC converters to be used for further system cost reduction. A charge cycle of the MC34674 includes trickle, constant current (CC) and constant voltage (CV) charge modes. The CC-mode current is selectable from 50 mA to 1.05 A, with 10% accuracy and the constant-output voltage in the CVmode is fixed at 4.2 V. BC3770 2.0 A Switch-Mode Li-ion/Li-polymer Battery Charger The BC3770 is a fully programmable switching charger with dual-path output for single-cell Li-Ion and Li-Polymer battery. This dual-path output allows mobile applications with a fully discharged battery to boot up the system. 34676 Dual 28 V Input Voltage Charger with Linear Regulator The 34676 is a dual 28 V input voltage and fully-integrated single cell Li-Ion battery charger targeting smart handheld applications. One of the inputs is optimized for charging with a USB port and the second is optimized for an AC/DC adapter power source. The charger has two 28 V power devices to eliminate the needs of any external power-source selection and input over-voltage-protection circuitry. Each of the power devices independently controls the charge current from the input and behaves as an independent charger. Only one of the two chargers operates at a time. The AC charger current and the USB charger current are programmable up to 1.2 A and 400 mA with an external resistor respectively. 34700 9-18 V Four Output, Multi-Purpose Switching Power Supply The 34700 is a compact, high efficiency power supply, with on-chip power MOSFETs that feature three step down switching regulators and one low dropout linear regulator. The switching regulators utilize voltage mode control with external compensation, allowing flexibility in optimizing the performance of the 34700 for a given application. 34972 33975 34975 33978 34978 MR2001 17 Applications Analog, Mixed-Signal, and Power Management ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL CONDITIONING, AND RADAR (continued) Freescale Part Number Description 34704 Multi-channel Power Management IC (PMIC) The 34704 is a multi-channel power management IC (PMIC) used to address power management needs for various multimedia application microprocessors. Its ability to provide either 5 or 8 independent output voltages with a single input power supply (2.7 and 5.5 V) together with its high efficiency, make it ideal for portable devices powered up by Li-Ion/polymer batteries or for USB powered devices as well. 34708 Power Management Integrated Circuit (PMIC) for the i.MX50/53 Families The 34708 is the PMIC designed specifically for use with the Freescale i.MX50 and i.MX53 processor families. As the companion PMIC on several i.MX reference designs, it is a proven solution, which enables a faster time to market with fewer resources. 34709 Power Management Integrated Circuit (PMIC) for i.MX50/53 Families The 34709 is the Power Management Integrated Circuit (PMIC) designed primarily for use with the Freescale i.MX50 and i.MX53 families. It offers a low cost solution targeting embedded applications that do not require a battery charger. 34VR500 Power Management Integrated Circuit for QorlQ LS1 networking communications processors The 34VR500 is a high performance, highly integrated, multi-output, SMARTMOS, DC/DC regulator solution, with integrated power MOSFETs ideally suited for the LS1 family of communication processors. PF0100 14 Channel Configurable Power Management Integrated Circuit The PF0100 Power Management Integrated Circuit (PMIC) provides a highly programmable/ configurable architecture, with fully integrated power devices and minimal external components. With up to six buck converters, six linear regulators, RTC supply, and coin-cell charger, the PF0100 can provide power for a complete system, including applications processors, memory, and system peripherals, in a wide range of applications. PF0200 12 Channel Configurable Power Management Integrated Circuit The PF0200 Power Management Integrated Circuit (PMIC) provides a highly programmable/ configurable architecture, with fully integrated power devices and minimal external components. With up to four buck converters, one boost regulator, six linear regulators, RTC supply, and coin-cell charger, the PF0200 can provide power for a complete system, including applications processors, memory, and system peripherals, in a wide range of applications. PF3000 Power Management Integrated Circuit (PMIC) for i.MX 7 & i.MX 6 DL/SL/SX The PF3000 is a Power Management Integrated Circuit (PMIC) designed specifically for use with the Freescale i.MX 7 and i.MX 6 DL/SL/SX application processors. 34713 Single Synchronous Buck Switching Regulator (5.0 A) Synchronous buck switching regulator with adjustable output and an accuracy of ±2% and a programmable switch frequency of 200 KHz to 1.0 MHz. 34716 Dual Synchronous Buck Switching Regulators (5.0 A, +/-3.0 A) Synchronous buck switching regulators with adjustable outputs and an accuracy of ±2% and a programmable switch frequency of 200 KHz to 1.0 MHz. 34717 Dual Synchronous Buck Switching Regulators (5.0 A, 5.0 A) Synchronous buck switching regulators with adjustable outputs and an accuracy of ±2% and a programmable switch frequency of 200 KHz to 1.0 MHz. 34844 10 Channel LED Backlight Driver with Integrated Power Supply The 34844 is a high efficiency, LED driver for use in backlighting LCD displays from 10" to 20"+. Operating from supplies of 7.0 to 28 V, the 34844 is capable of driving up to 160 LEDs in 10 parallel strings. FS6407 Safe System Basis Chip with Buck and Boost DC/ DC up to 800 mA Multiple switching and linear voltage regulators, built-in enhanced high-speed CAN interface fulfills the ISO11898-2 and -5 standards. FS6408 Safe System Basis Chip with Buck and Boost DC/ DC up to 1.5 A Multiple switching and linear voltage regulators, built-in enhanced high-speed CAN interface fulfills the ISO11898-2 and -5 standards. 33909 System Basis Chip with Multiple Switch-to-Ground Interface The 33909/34FS4409 integrates the common functionality of system basis chips with switch detection inputs. The device works as an advanced power management unit for the MCU and additional integrated circuits such as sensors, CAN transceivers, and eXtreme switches. 1.4 A Dual H-Bridge Driver Compatible with 3.0 V Logic The 34933 is a two channel H-Bridge driver aimed at the digital camera market. There are a variety of applications containing bipolar step motors and/or brush DC motors, such as Auto Focus control for the digital camera lens. The 34933 uses Freescale's proprietary SMOS8 Bi CMOS process to deliver a low power device, with a maximum quiescent current of 100 µA for the motor drive supply and 400 µA for the Control Logic supply. FS4409 34933 18 Main Characteristics Analog, Mixed-Signal, and Power Management Applications ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL CONDITIONING, AND RADAR (continued) Freescale Part Number Description Main Characteristics 908E621 Integrated Quad Half-bridge and Triple High-side with Embedded MCU and LIN for High End Mirror A high performance HC08 microcontroller with a SMARTMOS analog control IC. The analog control die provides four half-bridges and three high-side outputs with diagnostic functions, a Hall Effect sensor input, analog inputs, voltage regulator, window watchdog, and local interconnect network (LIN) physical layer. 908E622 Integrated Quad Half-bridge, Triple High-side and EC Glass Driver with Embedded MCU and LIN for High End Mirror A high performance HC08 microcontroller with a SMARTMOS analog control IC. The analog control die provides four half-bridge and three high-side outputs with diagnostic functions, an EC glass driver circuit, a Hall Effect sensor input, analog inputs, voltage regulator, window watchdog, and local interconnect network (LIN) physical layer. 908E624 Integrated Triple High-side Switch with Embedded MCU and LIN Serial Communication for Relay Drivers A high performance HC08 microcontroller with a SMARTMOS analog control IC. The analog control die provides three high-side outputs with diagnostic functions, voltage regulator, watchdog, current sense operational amplifier, and local interconnect network (LIN) physical layer. 908E625 Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication A high performance HC08 microcontroller with a SMARTMOS analog control IC. The analog control die provides fully protected H-Bridge/high-side outputs, voltage regulator, autonomous watchdog with cyclic wake-up, and local interconnect network (LIN) physical layer. 908E626 Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication The analog control die provides fully protected H-Bridge outputs, voltage regulator, autonomous watchdog, and local interconnect network (LIN) physical layer. 912_634 Integrated S12 Based Relay Driver products with LIN, with 32/ 48/ 64 kB Flash memory The MM912_634 products are integrated single package solutions that integrate an HCS12 microcontroller with a SMARTMOS analog control IC, which combine a system base chip and application specific functions, including a Local Interconnect Network (LIN) transceiver 912_637 Battery Sensor with LIN for 12 V Lead-acid Batteries The MM912_637 is an integrated single package solution that integrates an HCS12 microcontroller, with a SMARTMOS analog control IC containing system base chip and application specific functions, including a LIN transceiver 9Z1_638 Battery Sensor with CAN and LIN The MM9Z1_638 enables precision measurement of key battery parameters in automotive and other applications. The device integrates an S12Z microcontroller and a SMARTMOS analog control IC into a single package solution. 912_P812 S12P MCU and Multifunctional Ignition and Injector The MM912_P812 is an engine control IC combining an MCU (S12P) and analog Driver System In Package (SiP) control die (MC33812) intended for motorcycle and other single/dual cylinders small engine control applications. 912_S812 S12XS MCU and Multifunctional Ignition and Injector Driver System In Package (SiP) The MM912_S812 is an engine control IC combining an MCU (S12XS) and analog control die (MC33812) intended for motorcycle and other single/dual cylinders small engine control applications. 17510 0.45 Ohm (TYP) H-Bridge Motor Driver The 17510 is a monolithic H-Bridge that is ideal in portable electronic applications to control small brush DC motors such as digital still and single lens cameras. 17529 0.7 Ohm TYP Dual H-Bridge Motor Driver The 17529 is a monolithic dual H-Bridge that is ideal in portable electronic applications to control bipolar stepper motors and brush DC motors such as found in camera lens shutters, optical disk drives and other head positioners. 17531 700 mA Dual H-Bridge Motor Driver with 3.0 V Compatible Logic I/O The 17531 is a monolithic dual H-Bridge driver IC with integrated charge pump and protection. 17533 0.7 Ohm (TYP) Dual H-Bridge Motor Driver The 17533 is a monolithic dual H-Bridge IC that is ideal in portable electronic applications for controlling stepper or brush DC-motors for example, camera lens shutters and optical disk drives. 0.4 Amp Dual H-Bridge Motor Driver IC A dual-channel H-Bridge power IC is deal for portable electronic applications containing bipolar stepper motors or brush DC motors, like those in cameras. 33HB2000 10 A H-Bridge, Programmable Brushed DC Motor Driver The 33HB2000 is a monolithic H-Bridge Power IC, enhanced with SPI configurability and diagnostic capabilities. 33HB2001 10 A H-Bridge, Programmable Brushed DC Motor Driver The 33HB2001 is a monolithic H-Bridge Power IC, enhanced with SPI configurability and diagnostic capabilities. 33GD3000 Three Phase Field Effect Transistor Pre-driver The GD3000 is a field effect transistor (FET) pre-driver designed for three phase motor control and similar applications. 17C724 34GD3000 19 Applications Analog, Mixed-Signal, and Power Management ANALOG DEVICES FOR POWER ACTUATION, POWER MANAGEMENT, NETWORK TRANSCEIVERS, SIGNAL CONDITIONING, AND RADAR (continued) Freescale Part Number 20 Description Main Characteristics SB0400 Two-Wheel Antilock Braking (ABS) Controller for Motorcycles The MC33SB0400 motorcycle antilock brake (ABS) controller has two high current low-side drivers for solenoid valves, two configurable wheel speed sense inputs for active sensors, and high-side gate drivers for controlling two external N-channel MOSFETs. SB0401 One-Wheel Antilock Braking (ABS) for Motorcycles The MC33SB0401 motorcycle antilock brake (ABS) controller has four high current low-side drivers for solenoid valves, two configurable wheel speed sense inputs for handling active sensors, and high-side gate drivers for controlling two external Nchannel MOSFETs. 34SB0410 Quad Valve Controller System on Chip The Quad Valve Controller system on a chip (SoC), with integrated pump driver, consists of four regulated low-side drivers and a high-side driver to control a DC motor. 34SB0800 Octal Valve Controller System on Chip The Octal Valve Controller system on a chip (SoC), with integrated pump driver, consists of four regulated low-side drivers and four digital low-side driver, plus a high-side driver to control a DC motor. Analog, Mixed-Signal, and Power Management References Topic Applications URL BR1567 Analog ICs Integrated Solutions Technology Brochure http://www.freescale.com/files/analog/doc/brochure/ BR1567.pdf BR1568 Analog ICs Integrated Solutions Packaging Brochure http://www.freescale.com/files/analog/doc/brochure/ BR1568.pdf SG1002 Analog, Mixed Signal and Power Management - http://www.freescale.com/files/shared/doc/selector_guide/ SG1002.pdf Selector Guide SG187 Automotive - Selector Guide http://www.freescale.com/files/microcontrollers/doc/ selector_guide/SG187.pdf SG200 Analog and Power Management Industrial Products - Selector Guide http://www.freescale.com/files/shared/doc/selector_guide/ SG200.pdf BRAUTOSOL Automotive Solutions - Brochure http://www.freescale.com/files/microcontrollers/doc/brochure/ BRAUTOSOL.pdf MDAPPUSGDRM118 Medical Applications - User Guide http://www.freescale.com/files/microcontrollers/doc/ user_guide/MDAPPUSGDRM118.pdf 21 Communicating Controlling Protecting Learn More: For current information about Freescale products and documentation, please visit www.freescale.com. Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. SMARTMOS is a trademark of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © 2015 Freescale Semiconductor, Inc. Document Number: BR1569, Rev. 15.0, 11/2015