Freescale Semiconductor Application Note Document Number: AN4622 Rev. 5.0, 6/2015 MMPF0100 and MMPF0200 Layout Guidelines 1 Introduction This document describes good practices for the layout of PF0100 and PF0200 devices on printed circuit boards. Though the guidelines are applicable to PF0100 and PF0200, reference is made only to the PF0100 throughout the document for simplicity. Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 Recommended Layer Stack . . . . . . . . . . . . . . 2 4 Component Placement Hints . . . . . . . . . . . . . 2 5 General Routing Guidelines . . . . . . . . . . . . . . 3 6 I2C Communication Signals . . . . . . . . . . . . . . 3 7 Switching Power Supply Traces . . . . . . . . . . . 4 8 Effective Grounding . . . . . . . . . . . . . . . . . . . . . 8 9 Exposed Pad Connection . . . . . . . . . . . . . . . . 8 10 Feedback Signals . . . . . . . . . . . . . . . . . . . . . . 9 11 References . . . . . . . . . . . . . . . . . . . . . . . . . . 10 12 Revision History . . . . . . . . . . . . . . . . . . . . . . 11 © Freescale Semiconductor, Inc., 2013-2015. All rights reserved. Packaging 2 Packaging The PF0100 device is intended for use in commercial and industrial applications and is offered in a standard QFN for consumer and industrial applications. The PF0100Z is intended for use in automotive applications and is available in a Wettable-Flank QFN for automotive applications. Both packages are 56-pin and have an a 8 x 8 mm outline. Refer to Table 1 for the package drawing information for both packages. Refer to Application Note AN1902 for guidelines on the handling and assembly of Freescale QFN packages during PCB assembly, guidelines for PCB design and rework, and package performance information (such as Moisture Sensitivity Level (MSL) rating, board level reliability, mechanical, and thermal resistance data). Package dimensions are provided in package drawings. To find the most current package outline drawing, go to www.freescale.com and perform a keyword search for the drawing’s document number. Table 1. Package Drawing Information Product Family Package Suffix Package Outline Drawing Number MMPF0100 56 QFN 8x8 mm - 0.5 mm pitch. E-Type (full lead) 56 QFN 8x8 mm - 0.5 mm pitch. WF-Type (wettable flank) 56 QFN 8x8 mm - 0.5 mm pitch. E-Type (full lead) EP 98ASA00405D ES 98ASA00379D EP 98ASA00405D MMPF0100Z MMPF0200 3 Recommended Layer Stack Table 2 shows the recommended layer stack-up for the signals to receive good shielding. Table 2. Layer Stack-up Recommendation Layer Stack-up Layer 1 (Top) Signal Layer 2 (Inner 1) Ground Layer 3 (Inner 2) Power Layer 4 (Bottom) Signal/Ground Note: A more detailed layer design may be required to route the i.MX processor. If the PF0100 is being interfaced with an i.MX processor, just four of the layers will be needed to route it. 4 Component Placement Hints Place these components as close as possible to the IC in order of priority: • • • • • • Input capacitor of the buck regulators (SW1, SW2, SW3, and SW4) Output diode and output capacitor of the boost converter (SWBST) VIN, VCOREREF, VCORE, and VCOREDIG capacitors LICELL capacitor (if a coin cell is used in system) VSNVS, VREFDDR, and VGENx capacitors Switching regulator inductors AN4622, Rev. 5.0 2 Freescale Semiconductor General Routing Guidelines 5 General Routing Guidelines • • • • • 6 Shield feedback paths of the regulators from noise planes and traces The Exposed Pad (EP) on the PF0100 is the high current ground return for all the buck regulators and the boost regulator. Use vias under the EP to drop in directly onto the ground plane(s), ensuring sufficient copper for the ground return. Pins 14, 15, 32, and 48 are signal ground pins. Ground return currents from the switching regulators must not flow through these pins. The SWxIN, SWxLX, and SWBSTLX nodes are high dI/dt nodes and act as antennas. They are also high current paths. Hence their traces must be kept short and wide. Avoid coupling traces between important signal/low noise supplies (like VCOREREF) and switching nodes. I2C Communication Signals To avoid contamination of these signals by nearby high power or high frequency signals, it is a good practice to shield them with ground planes placed on adjacent layers. Make sure the ground plane is uniform throughout the whole signal trace length. Figure 1. Recommended Shielding for Critical Signals AN4622, Rev. 5.0 Freescale Semiconductor 3 Switching Power Supply Traces 7 Switching Power Supply Traces In the buck and boost configurations, length of the ‘critical traces’ must be kept minimal. ‘Critical traces’ refer to current paths which have high dI/dt. Refer to sections 7.1 and 7.2 for details. 7.1 Buck Regulator Figure 2 shows current paths in a buck converter in the ‘on’ and ‘off’ periods of the switching cycle. Critical traces refer to traces which conduct either only during the ‘on’, or only during the ‘off’ periods, as highlighted in red. Control FET On Synchronous FET On SWxIN SWxLX Critical Traces EP Figure 2. Buck Converter Critical Traces In the buck regulators of the PF0100, the top and bottom MOSFETs are integrated within the package. Hence, placement of the input capacitor close to the SWxIN pin and the exposed pad (EP) is critical. Figure 4 and Figure 5 show an example layout for the buck regulators. AN4622, Rev. 5.0 4 Freescale Semiconductor Switching Power Supply Traces Figure 3. SW1AB Schematic - Reference for Figures 4 and 5 SW1AIN SW1ALX SW1BLX SW1BIN Figure 4. SW1AB Layout - Top layer components + Top Silkscreen Figure 5. SW1AB Layout - Bottom Layer Components + Top and Bottom Silkscreen AN4622, Rev. 5.0 Freescale Semiconductor 5 Switching Power Supply Traces 7.2 Boost converter Figure 6 shows the critical traces in a boost converter. Control FET On Diode conducting SWBSTLX Critical traces EP Figure 6. Boost Converter Critical Traces In the SWBST regulator of the PF0100, the switching MOSFET is integrated within the package. The loop formed by the switching MOSFET, the diode and the output capacitor, must be minimized to keep parasitic inductances small. Figure 8 and Figure 9 show an example of the SWBST layout. AN4622, Rev. 5.0 6 Freescale Semiconductor Switching Power Supply Traces SWBSTLX SWBSTIN SWBSTIX SWBSTIN Figure 7. SWBST Schematic - Reference for Figures 8 and 9 Figure 8. SWBST Example Layout. Top Layer Components + Top Silkscreen Figure 9. SWBST Example Layout. Bottom Layer Components + Top and Bottom Silkscreen AN4622, Rev. 5.0 Freescale Semiconductor 7 Effective Grounding 8 Effective Grounding • • • 9 The practice of ‘star grounding’ must be followed for best performance of the PF0100. The exposed pad (EP) is the ground return for all the switching regulators and should be connected to the ground plane through multiple vias. SW1VSSSNS (pin 14), GNDREF1 (pin 15), SW3VSSSNS (pin 32), and GNDREF (pin 48) are signal ground pins. Connect these pins to the ground plane using separate vias not through EP, to prevent coupling from return currents of the switching regulators which pass through the EP. Exposed Pad Connection The exposed pad (EP) is the ground return for all the switching regulators and should be connected to the ground plane(s) through vias. A minimum of 16 vias is recommended under the EP. The EP also acts as a heat sink for the PF0100 hence the vias should not have thermal relief. They must be solid thermal vias as shown in Figure 10. Thermal Relief Via – Not Recommended Solid Thermal Via – Recommended Figure 10. Types of Via ‘Wicking’ of solder through the bore in the vias increase their thermal resistance. Follow techniques such as tenting or via encroaching to prevent solder wicking. Using a bore diameter of 0.3 mm or less also helps minimize wicking due to the surface tension of the liquid solder. Apply the solder paste to approximately 50 to 75% of the area of the exposed pad. Rather than applying the solder paste in one large section, apply it in multiple smaller sections. This can be accomplished by using an array of openings in the solder stencil. Sectioning helps in even spreading of the solder, as well as in minimizing out-gassing, which can create voids and bridges under the exposed pad. Figure 11 shows an example of how the exposed pad can be laid out. AN4622, Rev. 5.0 8 Freescale Semiconductor Feedback Signals Figure 11. Exposed Pad Via Array 10 Feedback Signals The control loop regulates output voltage at the point where the feedback trace meets the output rail. It is recommended to connect the feedback trace to the output voltage rail near the load for best load regulation. It must be ensured that this trace does not couple noise from other traces/layers. AN4622, Rev. 5.0 Freescale Semiconductor 9 References 11 References Document Number and Description URL MMPF0100 Data Sheet http://www.freescale.com/files/analog/doc/data_sheet/MMPF0100.pdf MMPF0200 Data Sheet http://www.freescale.com/files/analog/doc/data_sheet/MMPF0200.pdf AN1902 QFN Application Note http://www.freescale.com/files/analog/doc/app_note/AN1902.pdf Freescale.com Support Pages URL MMPF0100 Product Summary Page http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MMPF0100 MMPF0200 Product Summary Page http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MMPF0200 Power Management Home Page Analog Home Page http://www.freescale.com/webapp/sps/site/homepage.jsp?code=POWERMGTHOME http://www.freescale.com/analog AN4622, Rev. 5.0 10 Freescale Semiconductor Revision History 12 Revision History Revision Date Description of Changes 2.0 11/2012 • Initial release 3.0 3/2013 • Deleted specific package drawings and ref in the table 1 to the 98A spec. 4.0 6/2013 • Added information on the MMPF0200 5.0 6/2015 • AN4530 is replaced by AN1902 AN4622, Rev. 5.0 Freescale Semiconductor 11 How to Reach Us: Information in this document is provided solely to enable system and software implementers to use Freescale products. Home Page: freescale.com There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based Web Support: freescale.com/support Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no on the information in this document. warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale data sheets and/or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including “typicals,” must be validated for each customer application by customer’s technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale sells products pursuant to standard terms and conditions of sale, which can be found at the following address: freescale.com/SalesTermsandConditions. Freescale and the Freescale logo, are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. All other product or service names are the property of their respective owners. © 2015 Freescale Semiconductor, Inc. Document Number: AN4622 Rev. 5.0 6/2015