Analog Accelerometer 34205A

PRELIMINARY
34205A
±5 g to ±50 g Triaxial Accelerometer
Superior Zero g Bias Stability
Low Noise - Wide Bandwidth
5
8
Technical Data*
Features and Benefits
High Accuracy and Linearity over Wide Temperature Range
The voltage output for each axis of the 34205A is directly proportional to the
acceleration along that axis. Each DC-coupled output is fully scaled,
referenced, and temperature compensated over the entire -40 to +85°C
temperature range.
CalibrationCertificate
Each 34205A is supplied with a calibration certificate listing sensitivity and
offset, as well as the on-axis and transverse alignment parameters needed
to ensure rapid and efficient system implementation. The alignment data can
be used to compensate the measured values to achieve an even higher level
of sensor accuracy.
Small Size
Complete conditioned triaxial accelerometer in less than a cubic inch.
­ uilt-In Power Supply Regulation
B
Unregulated DC power from +8 to +18 volts is all that is required to measure
accelerations on all axes.
Suitable for Harsh Environments
The 34205A is robust and can be used in harsh environments. The unit is
packaged in a rugged aluminum housing and will survive 5000 g powered or
unpowered.
Warranty
These Measurement Specialties accelerometers come with a three-year
factory warranty.
34205A Triaxial Analog Accelerometer
precisionsensors.meas-spec.com Precisely Measure
Real-World Accelerations
Measurement
Specialties
34205A
accelerometer provides the accuracy
required by most measurement
applications without any compensation.
Critical applications requiring higher
accuracy can use the alignment data
provided on the calibration certificate to
compensate for any small residual error.
Choose the bandwidth and range options
best suited for your application to measure ±5 g, ±10 g, ±20 g, ±25 g, ±30 g,
±40 g, or ±50 g accelerations on each of
three axes.
Each axial sensor has been tested over
the -40 to +85°C temperature range and
has a nominal full scale output swing of
±2.25 volts. The zero g output level is
nominally +2.5 volts. Precise values for
each axis are available on the included
calibration certificate.
2236 N. Cleveland-Massillon Road
Akron OH 44333 PH : 330-659-3312 8/5/2013
www.meas-spec.com
PRELIMINARY
Specifications for 34205A - improved specifications available upon request
Ta = Tmin to Tmax; 8 ≤ Vs ≤ 18 V; Acceleration = 0 g unless otherwise noted; within one year of calibration.
Max
Units
Range Measurement Full Scale
Parameter
±5
±50
g
On each axis. Must specify via Option Rnnn
Sensitivity
At 25°C, Option R050
Drift Tmin to Tmax
40†
±2.0
mV/g
%
Nom ±50 g. Precise values on cal certificate
Percent of sensitivity at 25°C
Zero g Bias Level
At 25°C
Drift Tmin to Tmax:
Option R050, R040, R030, R025, R020
Option R010, R005
Min
Typical
Conditions/Notes
2.5
±80
±16
Alignment
Deviation from Ideal Axes
±0.35
Nonlinearity
0.15
Frequency Response
Noise Density
Option R050, R040, R030, R025, R020
Option R010, R005
50
10
μg/√Hz
μg/√Hz
Temperature Sensor
Sensitivity
0°C Bias Level
6.45
509
mV/°C
mV
Outputs
Output Voltage Swing
Capacitive Drive Capability
0.25
500
4.75
V
pF
Iout = ±0.5 mA
Power Supply (Vs)
Input Voltage - Operating
Input Current
Rejection Ratio
+8
33
>120
+18
50
V
mA
dB
Will withstand -20 V continuous or 36 V for <1 sec.
No load, quiescent
DC
Temperature Range (Ta)
-40
+85
°C
Mass
Shock Survival
-5000
†Scale
0
V
Precise values on cal certificate
±200
±40
mg
mg
At <1.25°C/min temperature rate of change
At <1.25°C/min temperature rate of change
±3.0
degrees
Precise values on cal certificate
Can be compensated if required
0.5
% FSR
Best fit straight line
2000
Hz
35
Upper Cutoff per Option Bnnn, -3 dB pt ±10%
grams
+5000
g
Ta =25°C
Accuracy ±1°C typical
Precise values on cal certificate
Any axis for 0.1 ms, powered or unpowered
linearly with range option Rnnn; see Ordering Information
Mechanical
Connections
T004
Pin
Signal
Wire
1
A1+
Brown
2
3
4
5
Signal-
A2+ +5VOut A3+
Red
Orange Yellow Green
6
T+
Blue
7
N.C.
Violet
8
+Vs
Grey
9
Gnd
White
Ordering Information
34205A
Two 3 mm
x 0.5 mm
threaded holes
are provided
on each of
three orthogonal faces for
mounting.
34205A Triaxial Analog Accelerometer
precisionsensors.meas-spec.com -
R050
-
B2k0
-
T004
Instrument
34205A
Shown with 34170B
mounting adapter
(sold separately)
Range
Bandwidth
R050 : ±50 g B2k0 : 0 to 2000 Hz
R040 : ±40 g B1k4 : 0 to 1400 Hz
R030 : ±30 g B944 : 0 to 944 Hz
R025 : ±25 g B380 : 0 to 380 Hz
R020 : ±20 g B208 : 0 to 208 Hz
R010 : ±10 g B1k0 : 0 to 1000 Hz
B944 : 0 to 944 Hz
R005 : ±5 g
B380 : 0 to 380 Hz
B208 : 0 to 208 Hz
2236 N. Cleveland-Massillon Road
Akron OH 44333 PH : 330-659-3312 Termination
T004 : 4 ft. cable with DB9M
T000 : PCB Mount (Not shown, Call SI)
Tnnn : Custom length, nnn ft. (Call SI)
8/5/2013
www.meas-spec.com