Designed and Manufactured in Germany Specification Oscillator type: Rev.: 5 Date: 2014-04-18 AXIOM30HP High-performance OCXO in 16-Pin DIL package Parameter Nominal frequency (Note 2) Frequency stability Initial tolerance @ +25°C vs. operating temperature range vs. supply voltage variation vs. load change Long term (aging) per day st Long term (aging) 1 year Long term (aging) per 15 years after Frequency adjustment range Electronic Frequency Control (EFC) EFC voltage VC EFC slope (∆f / ∆VC) EFC non-linearity EFC input impedance RF output Signal waveform Load RL Output level Harmonics Spurious Warm-up time @ +25°C Phase noise Short term stability (Allan deviation) Oven alarm output (Pin 10) Oscillator enable input (Pin 2) (Note 3) Reference voltage VREF output Supply voltage VS Current consumption (steady state) Current consumption (warm-up) Operating temperature range Enclosure (see drawing) (LxWxH) Weight Packing Notes: 1. 2. 3. min. typ. max. Unit Condition ±0.5 ±0.5 ±30 ±500 MHz ppm ppb ppb ppb ppb ppb ppb ppb VC @ VREF/2 steady state VS ±5% RL ±5% after 30 days operation after 30 days operation after 30 days operation VREF ppm V 10.000 ±50 ±100 ±5 ±0.5 ±0.8 0 ±1.0 2.5 Positive 2 5 100 Sine wave 50 +5 +10 -30 -90 3 10 -105 -100 -135 -130 -150 -145 -150 -157 -160 -150 -12 -12 2·10 5·10 -12 -11 2·10 1·10 -12 -11 5·10 5·10 LOW = alarm (not stable) HIGH = ready LOW = Oscillator OFF HIGH = Oscillator ON 5.0 11.4 12.0 12.6 150 350 -20 +70 24.8x20.3x11 max. 15 Palette % kΩ Ω dBm dBc dBc min dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz V V mA mA °C mm g ±5% ∆ffinal/fnominal < ±100 ppb @ 1Hz @ 10 Hz @ 100 Hz @ 1 kHz @ 10 kHz ~ 100 kHz τ=1s τ = 10 s τ = 100 s 0 … 0.4 V 2.4 … 5 V 0 … 0.4 V 2.4 … 12.6 V @ +25°C 16-Pin DIL package Terminology and test conditions are according to IEC60679-1 and MIL-PRF-55310, unless otherwise stated Other frequencies on request HCMOS compatible input GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXIOM30HP Rev.5 Drawing D0 Page 1(3) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Absolute Maximum Ratings Parameter min. max. Supply Voltage VS Control Voltage VC Oscillator Enable Voltage VOE Storage Temperature -0.5 -0.5 -0.5 -55 VS + 10% 15 VS +125 Unit Condition V V V °C VS to GND VC to GND VOE to GND Ordering Code Model Revision Frequency [MHz] AXIOM30HP Rev.5 10.000 Example: AXIOM30HP_Rev.5 – 100.000 MHz Enclosure drawing: Pin connections Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Symbol VS OE N.C. D.N.C. N.C. N.C. RF OUT GND N.C. OA N.C. N.C. N.C. N.C. VC VREF Function Supply Voltage Oscillator Enable Input No Connection Do Not Connect! (Internal use) No Connection No Connection RF Output Ground No Connection Oven Alarm Output No Connection No Connection No Connection No Connection Control Voltage (EFC) Reference Voltage * See Application Note AXAN-011 GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany AXIOM30HP Rev.5 Drawing D0 Page 2(3) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Designed and Manufactured in Germany Handling and Testing Parameter Procedure Handling and Testing Processing Source Application Note AXAN-011 Application Note AXAN-012 Parameter Procedure Electrostatic discharge (ESD) THD devices SMD devices Washable RoHS- Compliant IEC60749-26 IEC60749-27 Yes Yes www.axtal.com www.axtal.com Condition HBM MM No No 2000 V 200 V Environmental conditions Test Sealing tests (if applicable) Solderability Resistance to soldering heat Shock* IEC 60068 Part … 2-17 IEC 60679-1 Clause 5.6.2 MIL-STD202G Method 112E 2-20 2-58 5.6.3 208H 210F 2-27 5.6.8 213B Vibration, 2-6 5.6.7.1 201A sinusoidal* 204D Vibration, 2-64 5.6.7.3 214A random* Endurance tests 108A - ageing 5.7.1 - extended aging 5.7.2 Other environmental conditions on request MIL-STD810F Method MIL-PRF55310D Clause 3.6.1.2 3.6.52 3.6.48 516.4 3.6.40 516.4-4 3.6.38.1 3.6.38.2 3.6.38.3 3.6.38.4 514.5 4.8.35 Test conditions (IEC) Gross leak: Test Qc, Fine leak: Test Qk Test Ta Method 1 Test Td1 Method 2 Test Td2 Method 2 Test Ea, 3 x per axes 100g, 6 ms half-sine pulse Test Fc, 30 min per axes, 10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g Test Fdb 30 days @ 85°C, OCXO @25°C 1000h, 2000h, 8000h @85°C Data sheet is for information purposes only and may be subject to modifications or may be discontinued without notice. Revision History Rev. Drawing Date [dd.mm.yyyy] 4 5 D1 D0 01.10.2012 18.04.2014 GmbH & Co. KG Roemerring 9 D-74821 Mosbach Germany Remarks Editorial changes Various parameters updated, environmental conditions updated, editorial changes AXIOM30HP Rev.5 Drawing D0 Page 3(3) Author Checked BN HH BN HH www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected]