Data Sheet

Freescale Semiconductor
Data Sheet: Technical Data
VF3xxR, VF5xxR
Features
• Operating characteristics
– Voltage range 3 V to 3.6 V
– Temperature range(ambient) -40 °C to 85 °C
• ARM® Cortex® A5 Core features
– Up to 400 MHz ARM® Cortex® A5 core
– 32 KB/32 KB I/D L1 Cache
– 1.6 DMIPS/MHz based on ARMv7 architecture
– NEON™ MPE (Media Processing Engine) Coprocessor
– Double Precision Floating Point Unit
– 512 KB L2 cache (on selected part numbers only)
• ARM Cortex M4 Core features
– Up to 133 MHz ARM Cortex M4
– Integrated DSP capability
– 64 KB Tightly Coupled Memory (TCM)
– 16 KB/16 KB I/D L1 Cache
– 1.25 DMIPS/MHz based on ARMv7 architecture
• Clocks
– 24 MHz crystal oscillator
– 32 kHz crystal oscillator
– Internal reference clocks (128 KHz and 24 MHz)
– Phase Locked Loops (PLLs)
– Low Jitter Digital PLLs
• System debug, protection, and power management
– Various stop, wait, and run modes to provide low
power based on application needs
– Peripheral clock enable register can disable clocks to
unused modules, thereby reducing currents
– Low voltage warning and detect with selectable trip
points
– Illegal opcode and illegal address detection with
programmable reset or processor exception response
– Hardware CRC module to support fast cyclic
redundancy checks (CRC)
– 128-bit unique chip identifier
– Hardware watchdog
– External Watchdog Monitor (EWM)
– Dual DMA controller with 32 channels (with
DMAMUX)
Document Number VYBRIDRSERIESEC
Rev 7, 11/2014
VYBRIDRSERIESEC
• Debug
– Standard JTAG
– 16-bit Trace port
• Timers
– Motor control/general purpose timer (FTM)
– Periodic Interrupt Timers (PITs)
– Low-power timer (LPTMR0)
– IEEE 1588 Timer per MAC interface (part of
Ethernet Subsystem)
• Communications
– Six Universal asynchronous receivers/transmitters
(UART)/Serial communications interface (SCI) with
LIN, ISO7816, IrDA, and hardware flow control
– Four Deserial Serial peripheral interface (DSPI)
– Four Inter-Integrated Circuit (I2C) with SMBUS
support
– Dual USB OTG Controller + PHY
– Dual 4/8 bit Secure Digital Host controller
– Local Media Bus (MLB50)
– Dual 10/100 Ethernet (IEEE 1588)
– Dual FlexCAN3
• Security
– ARM TrustZone including the TZ architecture
– Secure Non-Volatile Storage (SNVS)
– Real Time Clock
– Real Time Integrity Checker (RTIC)
– TrustZone Watchdog (TZ WDOG)
– Trust Zone Address Space Controller
– Random Number Generator
– Hashing
– Secure JTAG
• Memory Interfaces
– 8/16-bit DRAM Controller with support for
LPDDR2/DDR3 - Up to 400 MHz (ECC supported
for 8-bit only and not 16-bit)
– 8/16-bit NAND Flash controller with ECC (ECC
supported for 8-bit only and not 16-bit)
– Dual Quad SPI with XIP (Execute-In-Place)
– 8/16/32-bit External bus (Flexbus)
Freescale reserves the right to change the detail specifications as may be
required to permit improvements in the design of its products.
© 2012–2013 Freescale Semiconductor, Inc.
• Display and Video
– Dual Display Control Unit (DCU) with support for color TFT display up to WVGA
– Segmented LCD (3V Glass only) configurable as 40x4, 38x8, and 36x6
– Video Interface Unit (VIU) for camera
– Open VG Graphics Processing Unit (GPU)
– VideoADC
• Analog
– Dual 12-bit SAR ADC with 1MS/s
– Dual 12-bit DAC
• Audio
– Four Synchronous Audio Interface (SAI)
– Enhanced Serial Audio Interface (ESAI)
– Sony Philips Digital Interface (SPDIF), Rx and Tx
– Asynchronous Sample Rate Converter (ASRC)
• Human-Machine Interface (HMI)
– GPIO pins with interrupt support, DMA request capability, digital glitch filter.
– Hysteresis and configurable pull up/down device on all input pins
– Configurable slew rate and drive strength on all output pins
• On-Chip Memory
– 512 KB On-chip SRAM with ECC
– 1 MB On-chip graphics SRAM (no ECC). This depends on the part selected. Alternate configuration could be 512 KB
graphics and 512 KB L2 cache.
– 96 KB Boot ROM
VF3xxR, VF5xxR, Rev7, 11/2014.
2
Freescale Semiconductor, Inc.
Table of Contents
1
Ordering parts.....................................................................................5
1.1
2
3
4
5
Determining valid orderable parts ..........................................5
USB PHY current consumption..............................21
6.2.5.1
Power Down Mode............................. 21
Part identification............................................................................... 5
6.2.6
EMC radiated emissions operating behaviors........ 21
2.1
Description.............................................................................. 5
6.2.7
EMC Radiated Emissions Web Search Procedure
2.2
Part Number Format................................................................5
2.3
Fields....................................................................................... 6
2.4
Part Numbers ..........................................................................7
boilerplate............................................................... 22
6.2.8
7
Terminology and guidelines...............................................................8
Capacitance attributes............................................. 22
I/O parameters....................................................................................22
7.1
GPIO parameters..................................................................... 22
3.1
Definition: Operating requirement.......................................... 8
3.2
Definition: Operating behavior............................................... 8
3.3
Definition: Attribute................................................................8
3.4
Definition: Rating....................................................................9
8.1
Power sequencing ...................................................................28
3.5
Result of exceeding a rating.................................................... 9
8.2
Power supply........................................................................... 30
3.6
Relationship between ratings and operating requirements......10
8.3
Absolute maximum ratings..................................................... 31
3.7
Guidelines for ratings and operating requirements................. 10
8.4
Recommended operating conditions....................................... 32
3.8
Definition: Typical value........................................................ 10
8.5
Recommended Connections for Unused Analog Interfaces... 33
3.9
Typical Value Conditions........................................................11
Handling ratings................................................................................. 12
7.1.1
7.2
8
9
Output Buffer Impedance measurement................. 24
DDR parameters......................................................................25
Power supplies and sequencing..........................................................28
Peripheral operating requirements and behaviours............................ 34
9.1
Analog..................................................................................... 34
4.1
ESD handling ratings ............................................................. 12
4.2
Thermal handling ratings........................................................ 12
9.1.1.1
12-bit ADC operating conditions........ 34
4.3
Moisture handling ratings........................................................12
9.1.1.2
12-bit ADC characteristics..................35
9.1.1
Operating Requirements.....................................................................13
5.1
6
6.2.5
9.1.2
12-bit ADC electrical characteristics...................... 34
12-bit DAC electrical characteristics...................... 39
Thermal operating requirements............................................. 13
9.1.2.1
12-bit DAC operating requirements....39
General............................................................................................... 13
9.1.2.2
12-bit DAC operating behaviors......... 39
6.1
AC electrical characteristics....................................................13
6.2
Nonswitching electrical specifications ...................................14
6.2.1
6.2.2
6.2.3
6.2.4
9.1.3
9.2
VREG electrical specifications .............................. 14
VideoADC Specifications.......................................43
Display and Video interfaces.................................................. 45
9.2.1
DCU Switching Specifications............................... 45
6.2.1.1
HPREG electrical characteristics........ 14
9.2.1.1
Interface to TFT panels (DCU0/1)......45
6.2.1.2
LPREG electrical characteristics.........14
9.2.1.2
Interface to TFT LCD Panels—Pixel
6.2.1.3
ULPREG electrical characteristics......15
6.2.1.4
WBREG electrical characteristics.......15
6.2.1.5
External NPN Ballast.......................... 16
Level Timings..................................... 46
9.2.1.3
Interface to TFT LCD panels—access
level..................................................... 47
LVD electrical specifications .................................18
9.2.2
Video Input Unit timing..........................................48
6.2.2.1
Main Supply electrical characteristics 18
9.2.3
LCD driver electrical characteristics...................... 49
6.2.2.2
LVD DIG characteristics.....................18
9.3
Ethernet specifications............................................................ 49
LDO electrical specifications .................................19
9.3.1
Ethernet Switching Specifications.......................... 49
6.2.3.1
LDO_1P1............................................ 19
9.3.2
Receive and Transmit signal timing specifications 49
6.2.3.2
LDO_2P5............................................ 19
9.3.3
Receive and Transmit signal timing specifications
6.2.3.3
LDO_3P0 ........................................... 20
Power consumption operating behaviors................ 20
for MII interfaces.................................................... 51
9.4
Audio interfaces...................................................................... 53
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
3
9.4.1
Enhanced Serial Audio Interface (ESAI) Timing
9.7.4
Parameters...............................................................53
9.5
9.6
9.7
9.4.2
SPDIF Timing Parameters...................................... 55
9.4.3
SAI/I2S Switching Specifications.......................... 56
Slow internal RC oscillator (128 KHz) electrical
characteristics..........................................................84
9.7.5
PLL1 and PLL2 (528 MHz System PLL)
Electrical Parameters.............................................. 84
Memory interfaces...................................................................58
9.7.6
PLL3 and PLL7 (480 MHz USB PLL) Electrical
9.5.1
QuadSPI timing.......................................................58
Parameters...............................................................84
9.5.2
NFC specifications..................................................61
9.7.7
PLL5 (Ethernet PLL) Electrical Parameters........... 85
9.5.3
FlexBus timing specifications.................................64
9.7.8
PLL4 (Audio PLL) Electrical Parameters...............85
9.5.4
DDR controller specifications................................ 66
9.7.9
PLL6 (Video PLL) Electrical Parameters...............85
9.5.4.1
DDR3 Timing Parameters ..................66
9.8
Debug specifications............................................................... 86
9.5.4.2
DDR3 Read Cycle...............................68
9.8.1
JTAG electricals..................................................... 86
9.5.4.3
DDR3 Write cycle...............................69
9.8.2
Debug trace timing specifications...........................88
9.5.4.4
LPDDR2 Timing Parameter................70
10 Thermal attributes.............................................................................. 89
9.5.4.5
LPDDR2 Read Cycle.......................... 71
10.1 Thermal attributes................................................................... 89
9.5.4.6
LPDDR2 Write Cycle......................... 72
11 Dimensions.........................................................................................90
Communication interfaces.......................................................73
11.1 Obtaining package dimensions ...............................................90
9.6.1
MediaLB (MLB) DC Characteristics..................... 73
12 Pinouts................................................................................................91
9.6.2
MediaLB (MLB) Controller AC Timing Electrical
12.1 Pinouts.....................................................................................91
Specifications..........................................................73
12.2 Pinout diagrams.......................................................................103
9.6.3
DSPI timing specifications..................................... 75
12.2.1
GPIO Mapping........................................................105
9.6.4
I2C timing............................................................... 78
12.2.2
Special Signal ........................................................ 109
9.6.5
SDHC specifications...............................................80
13 Power Supply Pins............................................................................. 111
9.6.6
USB PHY specifications.........................................81
13.1 Power Supply Pins.................................................................. 111
Clocks and PLL Specifications............................................... 81
14 Functional Assignment Pins...............................................................112
9.7.1
24 MHz Oscillator Specifications...........................81
14.1 Functional Assignment Pins....................................................112
9.7.2
32 KHz Oscillator Specifications........................... 82
15 Revision History.................................................................................121
9.7.3
Fast internal RC oscillator (24 MHz) electrical
characteristics..........................................................83
VF3xxR, VF5xxR, Rev7, 11/2014.
4
Freescale Semiconductor, Inc.
Ordering parts
1 Ordering parts
1.1 Determining valid orderable parts
Valid orderable part numbers are provided on the web.
1. To determine the orderable part numbers for this device, go to www.freescale.com
and search the required part number. The part numbering format is described in the
section that follows.
2 Part identification
2.1 Description
Part numbers for the chip have fields that identify the specific part. You can use the
values of these fields to determine the specific part you have received.
2.2 Part Number Format
The figure below represents the format of part number of this device.
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
5
Part identification
S V F 3 1 1 R 3 K1 C MK 2 R
Tape & Reel
R = Tape & Reel
(Optional)
Qualification Status
P = engineering samples
S = automotive qualified
Speed (A5 core)
2 = 266MHz
4 = 400MHz
Brand: V = Vybrid
Series: F = current
Package
KU = 176LQFP
MK = 364BGA
Family
3 = Standard
5 = Advanced
Core
1 = Cortex A5
2 = Cortex A5 + M4
3 = M4 Primary
Graphics
1 = No Open VG
2 = Open VG
Temp Spec
C = -40 to +85C Ta
Option
K1 = Placeholder
Version
R = Auto
Memory Option
3 = Standard (1.5MB SRAM)
2 = Optional (1MB SRAM and 512K L2 Cache)
Figure 1. Part Number Format
2.3 Fields
This table lists the possible values for each field in the part number (not all combinations
are valid):
Field
Description
Values
Q
Qualification status
• P = engineering samples
• S = automotive qualified
B
Brand
• V = Vybrid
S
Series
• F = current
F
Family
• 3 = Standard
• 5 = Advanced
C
Core
• 1 = Cortex A5
• 2 = Cortex A5 + M4
• 3 = M4 Primary
G
Graphics
• 1 = No Open VG
• 2 = OpenVG
V
Version
• R = Auto
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
6
Freescale Semiconductor, Inc.
Part identification
Field
Description
Values
M
Memory option
• 3 = Standard (1.5MB SRAM)
• 2 = Optional (1MB SRAM and
512K L2 Cache)
T
Temperature spec
• C = -40 C to +85 C Ta
P
Package
• KU = 176LQFP
• MK = 364BGA
S
Speed (A5 core)
• 2 = 266MHz
• 4 = 400MHz
0
0
2.4 Part Numbers
This table lists the part numbers on the device.
Part Number
Package
Description
SVF311R3K1CKU2
LQFP-EP 176 24*24*1.6
A5-266, 176LQFP-EP
SVF312R3K1CKU2
LQFP-EP 176 24*24*1.6
A5-266, OpenVG GPU, 176LQFP-EP
SVF321R3K1CKU2
LQFP-EP 176 24*24*1.6
A5-266, M4, 176LQFP-EP
SVF322R3K1CKU2
LQFP-EP 176 24*24*1.6
A5-266, M4, OpenVG GPU, 176LQFPEP
SVF331R3K1CKU2
LQFP-EP 176 24*24*1.6
A5-266, M4 Primary, 176LQFP-EP
SVF332R3K1CKU2
LQFP-EP 176 24*24*1.6
A5-266, M4 Primary, OpenVG GPU,
176LQFP-EP
SVF511R3K1CMK4
MAP 364 17*17*1.5 P0.8
A5-400, 364BGA
SVF512R3K1CMK4
MAP 364 17*17*1.5 P0.8
A5-400, OpenVG GPU, 364BGA
SVF521R3K1CMK4
MAP 364 17*17*1.5 P0.8
A5-400, M4, 364BGA
SVF522R2K1CMK4
MAP 364 17*17*1.5 P0.8
A5-400, M4, L2 Cache, OpenVG GPU,
364BGA
SVF522R3K1CMK4
MAP 364 17*17*1.5 P0.8
A5-400, M4, OpenVG GPU, 364BGA
SVF531R3K1CMK4
MAP 364 17*171.5 P0.8
A5-400, M4 Primary, 364BGA
SVF532R2K1CMK4
MAP 364 17*17*1.5 P0.8
A5-400, M4 Primary, L2 Cache OpenVG
GPU, 364BGA
SVF532R3K1CMK4
MAP 364 17*17*1.5 P0.8
A5-400, M4 Primary, OpenVG GPU,
364BGA
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
7
Terminology and guidelines
3 Terminology and guidelines
3.1 Definition: Operating requirement
An operating requirement is a specified value or range of values for a technical
characteristic that you must guarantee during operation to avoid incorrect operation and
possibly decreasing the useful life of the chip.
3.1.1 Example
This is an example of an operating requirement:
Symbol
VDD
Description
1.0 V core supply
voltage
Min.
0.9
Max.
1.1
Unit
V
3.2 Definition: Operating behavior
Unless otherwise specified, an operating behavior is a specified value or range of values
for a technical characteristic that are guaranteed during operation if you meet the
operating requirements and any other specified conditions.
3.2.1 Example
This is an example of an operating behavior:
Symbol
IWP
Description
Digital I/O weak pullup/ 10
pulldown current
Min.
Max.
130
Unit
µA
3.3 Definition: Attribute
An attribute is a specified value or range of values for a technical characteristic that are
guaranteed, regardless of whether you meet the operating requirements.
VF3xxR, VF5xxR, Rev7, 11/2014.
8
Freescale Semiconductor, Inc.
Terminology and guidelines
3.3.1 Example
This is an example of an attribute:
Symbol
CIN_D
Description
Input capacitance:
digital pins
Min.
—
Max.
7
Unit
pF
3.4 Definition: Rating
A rating is a minimum or maximum value of a technical characteristic that, if exceeded,
may cause permanent chip failure:
• Operating ratings apply during operation of the chip.
• Handling ratings apply when the chip is not powered.
3.4.1 Example
This is an example of an operating rating:
Symbol
VDD
Description
1.0 V core supply
voltage
Min.
–0.3
Max.
1.2
Unit
V
3.5 Result of exceeding a rating
Failures in time (ppm)
40
30
The likelihood of permanent chip failure increases rapidly as
soon as a characteristic begins to exceed one of its operating ratings.
20
10
0
Operating rating
Measured characteristic
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
9
Terminology and guidelines
3.6 Relationship between ratings and operating requirements
g(
era
Op
tin
g
in
rat
n.
mi
era
g
tin
u
req
)
in.
t (m
n
me
ire
Op
ire
g
tin
era
Op
u
req
t (m
n
me
ax
.)
g
tin
era
Op
x.)
ma
g(
in
rat
Fatal range
Degraded operating range
Normal operating range
Degraded operating range
Fatal range
Expected permanent failure
- No permanent failure
- Possible decreased life
- Possible incorrect operation
- No permanent failure
- Correct operation
- No permanent failure
- Possible decreased life
- Possible incorrect operation
Expected permanent failure
–∞
∞
Operating (power on)
ng
dli
n
Ha
–∞
)
rat
n.)
mi
(
ing
ng
dli
n
Ha
ma
rat
(
ing
x.)
Fatal range
Handling range
Fatal range
Expected permanent failure
No permanent failure
Expected permanent failure
∞
Handling (power off)
3.7 Guidelines for ratings and operating requirements
Follow these guidelines for ratings and operating requirements:
• Never exceed any of the chip’s ratings.
• During normal operation, don’t exceed any of the chip’s operating requirements.
• If you must exceed an operating requirement at times other than during normal
operation (for example, during power sequencing), limit the duration as much as
possible.
3.8 Definition: Typical value
A typical value is a specified value for a technical characteristic that:
• Lies within the range of values specified by the operating behavior
• Given the typical manufacturing process, is representative of that characteristic
during operation when you meet the typical-value conditions or other specified
conditions
Typical values are provided as design guidelines and are neither tested nor guaranteed.
VF3xxR, VF5xxR, Rev7, 11/2014.
10
Freescale Semiconductor, Inc.
Terminology and guidelines
3.8.1 Example 1
This is an example of an operating behavior that includes a typical value:
Symbol
Description
IWP
Digital I/O weak
pullup/pulldown
current
Min.
10
Typ.
70
Max.
130
Unit
µA
3.8.2 Example 2
This is an example of a chart that shows typical values for various voltage and
temperature conditions:
5000
4500
4000
TJ
IDD_STOP (μA)
3500
150 °C
3000
105 °C
2500
25 °C
2000
–40 °C
1500
1000
500
0
0.90
0.95
1.00
1.05
1.10
VDD (V)
3.9 Typical Value Conditions
Typical values assume you meet the following conditions (or other conditions as
specified):
Symbol
Description
Value
Unit
TA
Ambient temperature
25
°C
VDD
3.3 V supply voltage
3.3
V
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
11
Handling ratings
4 Handling ratings
4.1 ESD handling ratings
Symbol
Description
Min.
Max.
Unit
Notes
VHBM
Electrostatic discharge voltage, human body model
-2000
2000
V
1
VCDM
Electrostatic discharge voltage, charged-device model
-500
500
V
2
Latch-up Current at ambient temperature of 85 °C
-100
100
mA
Description
Min.
Max.
Unit
Notes
TSTG
Storage temperature
–55
150
°C
1
TSDR
Solder temperature, lead-free
—
260
°C
2
Solder temperature, leaded
—
245
ILAT
1. Determined according to the AEC spec AEC-Q100-002 for HBM
2. Determined according to AEC spec AEC-Q100-011
4.2 Thermal handling ratings
Symbol
1. Determined according to JEDEC Standard JESD22-A103, High Temperature Storage Life.
2. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices.
4.3 Moisture handling ratings
Symbol
MSL
Description
Moisture sensitivity level
Min.
Max.
Unit
Notes
—
3
—
1
1. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic
Solid State Surface Mount Devices.
VF3xxR, VF5xxR, Rev7, 11/2014.
12
Freescale Semiconductor, Inc.
Operating Requirements
5 Operating Requirements
5.1 Thermal operating requirements
Table 1. Thermal operating requirements
Symbol
Description
Min.
Max.
Unit
TA
Ambient temperature
–40
85
°C
TJ
Junction temperature
105
°C
6 General
6.1 AC electrical characteristics
Unless otherwise specified, propagation delays are measured from the 50% to the 50%
point, and rise and fall times are measured at the 20% and 80% points, as shown in the
following figure.
VIH
Input Signal
High
Low
80%
50%
20%
Midpoint1
Fall Time
VIL
Rise Time
The midpoint is VIL + (VIH - VIL) / 2
Figure 2. Input signal measurement reference
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
13
Nonswitching electrical specifications
6.2 Nonswitching electrical specifications
6.2.1 VREG electrical specifications
6.2.1.1
HPREG electrical characteristics
Table 2. HPREG electrical characteristics
Parameters
Min
Typ
Max
Unit
Comments
Power supply
3.0
3.3
3.6
V
-
Current Consumption
-
1.2
1.5
mA
@ no load
-
2.0
2.5
mA
@ full load
-
600
12001
mA
DC load current
1.23
1.26
V
Output current capacity
Output voltage @ no load
Output voltage @ full load
1.20
1.21
V
External decoupling cap
4.7
-
μF
-
0.05
0.1
Ohms
ESR of external
cap
20
mOhms
Total effective
PAD+PCB trace
resistances
@ DC @noload
-48
dB
@ DC @full load
-40
@ worst case any frequency
-20
PSRR with 4.7uF output cap
1. This is peak and not continuous maximum value.
6.2.1.2
LPREG electrical characteristics
Table 3. LPREG electrical characteristics
Parameters
Min
Typ
Max
Unit
Power supply
3.0
3.3
3.6
V
Current Consumption
350
400
-
500
Output current capacity
Output voltage @ no load
μA
@ no load
650
μA
@ full load
100
200
mA
DC load current
1.22
1.240
V
Output voltage @ full load
1.180
V
External decoupling cap
4.7
μF
0.05
Comments
0.1
Ohms
ESR of external cap
20
mOhms
Total PAD+PCB trace
resistance
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
14
Freescale Semiconductor, Inc.
VREG electrical specifications
Table 3. LPREG electrical characteristics
(continued)
Parameters
Min
Typ
Max
Unit
@ DC @noload
-40
dB
@ DC @full load
-35
Worst case @ any frequency
-12
Comments
PSRR with 4.7uF output cap
6.2.1.3
ULPREG electrical characteristics
Table 4. ULPREG electrical characteristics
Parameters
Min
Typ
Max
Unit
Power supply
3.0
3.3
3.6
V
Current Consumption
1.88
2.3
2.86
μA
-
610
670
μA
@ full load
20
mA
DC load current
1.175
V
Output current capacity
Output voltage @ no load
Output voltage @ full load
PSRR with 500 pF output cap
1.125
V
-20
dB
@ DC @noload
-50
@200KHz @noload
-37
@ DC @full load
-42
@200KHz @full load
-37
Worst case @ any frequency
@ any load
-15
6.2.1.4
Comments
@ no load
Worst case at any frequency
across corners
dB
WBREG electrical characteristics
Table 5. WBREG electrical characteristics
Parameters
Min
Typ
Max
Unit
Comments
Power supply
3
3.3
3.6
V
-
Current Consumption
-
2
5
µA
@ no load
-
2
5
µA
@ full load
-
1
2
mA
DC load current
1.4
1.425
V
Output current capacity
Output voltage @ no load
Output voltage @ full load
1.375
1.398
Output voltage programmability
1.4
1.4
V
1.7
V
16 steps of 25
mV each
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
15
VREG electrical specifications
6.2.1.5
External NPN Ballast
The internal main regulator requires an external NPN ballast transistor to be connected as
shown in the following figure as well as an external capacitance to be connected to the
device in order to provide a stable 1.2V digital supply to the device. The HPREG design
allows for collector voltage lower than VDDREG value. See AN4807 at
www.freescale.com .
NOTE
To not overload BCTRL output, collector voltage should appear
no later than VDDREG / VDD33 (3.3V).
Figure 3. External NPN Ballast connections
Table 6. BCTRL OUTPUT specification
Parameter
Value
Comments
BCTRL OUTPUT specification
20mA
BCTRL driver can not drive more than
20mA current
Maximum pin voltage
VDDREG-0.5V
For Example, VDDREG =3.0V BCTRL
should not exceed 2.5V.
Table 7. Assumptions For calculations
Parameter
Value
VDDREG
3.0V to 3.6V with typical value of 3.3V
Max DC Collector current
0.85A @85 °C
Emitter voltage
1.2V to 1.25V
Collector voltage
Equal to VDDREG
VF3xxR, VF5xxR, Rev7, 11/2014.
16
Freescale Semiconductor, Inc.
VREG electrical specifications
Table 8. General guidelines for selection of NPN ballast
Symbol
Parameters
Value
Hfe
Minimum DC
current gain (Beta)
42.5
PD (Junction to
ambient)
Minimum power
dissipation @
TA=85 °C
2.04
W
Assuming 0.85A collector current with
Collector voltage of Ballast 3.6V(max)
we get VCE= 3.6V-1.2V=2.4V So power
dissipated is 2.4V*0.85A=2.04W . This
should be met for junction to ambient
power dissipation spec of ballast
IcmaxDC peak
Maximum peak DC
collector current
0.85
A
1.2A and above capacity device
preferable
V
For a VDDREG of 3.0 V (min.), BCTRL
pin can drive voltage up to VDDREG 0.5 V = 2.5 V. Since emitter of ballast is
fixed at 1.25 V (max) if chosen ballast
can supply 0.85 A collector current @ 85
°C with a base-to-emitter voltage of 1.25
V or lower, it is suitable for application.
VBE
Ft
Maximum voltage 1.25V for 0.85A @
that BCTRL pin can
85 °C
drive
Unity current gain
Frequency of
Ballast
50
Unit
Comments
As BCTRL pin can not drive more than
20mA Minimum value of beta for a
collector current of 0.85A comes out to
be 42.5.
MHz
Reducing the collector-to-emitter voltage drop lowers the ballast transistor heat
dissipation. This can be implemented in two ways:
1. By introducing series resistor or diode(s) between the collector and VDDREG
(placed far enough from the transistor for proper cooling)
2. By connecting the collector to a separate lower-voltage supply
In both of the above cases the transistor has to stay away from the deep saturation region;
otherwise, due to significant Hfe degradation, its base current exceeds the BCTRL output
maximum value.
In general, the transistor must be selected such that its Vce saturation voltage is lower
than the expected minimum Collector-Emitter voltage, and at the same time, the base
current is less than 20 mA for the maximum expected collector current. More information
can be found in collateral documentation at http://www.freescale.com
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
17
LVD electrical specifications
6.2.2 LVD electrical specifications
6.2.2.1
Main Supply electrical characteristics
Table 9. LVD_MAIN supply electrical characteristics
Main Supply LVD
Parameters
Min
Typ
Max
Unit
Power supply
3.0
3.3
3.6
V
2.76
2.915
V
Upper voltage threshold
(value @27oC)
Lower voltage threshold
(value @27oC)
2.656
Time constant of RC filter at
LVD input (0.69*RC)
6.2.2.2
2.73
Comments
V
3.3
μs
3.3 V noise rejection at LVD
comparator input
LVD DIG characteristics
Table 10. LVD DIG electrical specifications [HPREG(RUN MODE) and
LPREG(STOP MODE)]
LVD DIG
Parameters
Min
Typ
Max
Unit
Power supply
3.0
3.3
3.6
V
Upper voltage
threshold
1.135
1.16
1.185
V
Lower voltage
threshold
1.105
1.13
1.155
V
Time constant of
RC filter at LVD
input
200
Comments
ns
1.2V noise rejection at the input of
LVD comparator
Table 11. LVD DIG electrical specifications [ULPREG(STANDBY
MODE)]
LVD DIG Parameters
Min
Typ
Max
Unit
Power supply
3.0
3.3
3.6
V
Upper voltage threshold
1.105
1.13
1.155
V
Lower voltage threshold
1.075
1.10
1.125
V
Time constant of RC filter at
LVD input
200
ns
Comments
1.2V noise rejection at the
input of LVD comparator
VF3xxR, VF5xxR, Rev7, 11/2014.
18
Freescale Semiconductor, Inc.
LDO electrical specifications
6.2.3 LDO electrical specifications
6.2.3.1
LDO_1P1
Specification
Table 12. LDO_1P1 parameters
Min
Typ
Max
Unit
Comments
VDDIO
3
3.3
3.6
V
IO supply
VDD1P1_OUT
0.9
1.1
1.2
V
Regulator output
I_out
-
150
mA
>= 300mV drop out
1.4
V
Programmable in
25mV steps
Regulator output
0.8
programming range
1.1
Brownout Voltage
0.85
0.94
Brownout offset
step
0
-
175
mV
Programmable in
25mV steps
Minimum external
decoupling
capacitor
1
-
-
µF
low ESR
V
For additional information, see the device reference manual.
6.2.3.2
LDO_2P5
Specification
Table 13. LDO_2P5 parameters
Min
Typ
Max
Unit
Comments
VDDIO
3
3.3
3.6
V
IO supply
VDD2P5_OUT
2.3
2.5
2.6
V
Regulator output
I_out
-
350
mA
@500mV drop out
2.75
V
Programmable in
25mV steps
Regulator output
2.0
programming range
2.5
[P:][C:] Brownout
Voltage
2.25
2.33
Brownout offset
step
0
-
175
mV
Programmable in
25mV steps
Minimum external
decoupling
capacitor
1
-
-
µF
low ESR
V
For additional information, see the reference manual.
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
19
LDO electrical specifications
6.2.3.3
LDO_3P0
Specification
Table 14. LDO_3P0 parameters
Min
Typ
Max
Unit
Comments
Input OTG VBUS
Supply
4.4
5.25
V
Input HOST VBUS
Supply
4.4
5.25
V
VDD3P0_OUT
2.9
3.1
V
Regulator output at
default setting
I_out
-
50
mA
500 mV drop-out
voltage
3.4
V
Programmable in
25mV steps
3.0
Regulator output
2.625
programming range
[P:][C:] Brownout
Voltage
2.75
2.85
V
Brownout offset
step
0
-
175
mV
Programmable in
25mV steps
Minimum external
decoupling
capacitor
1
-
-
µF
low ESR
NOTE
These values are with Anadig_REG_3P0[ENABLE_ILIMIT]=
0 and Anadig_REG_3P0[ENABLE_LINREG]= 1. It is required
to set these values before using USB.
6.2.4 Power consumption operating behaviors
Table 15. Power consumption operating behaviors
Symbol
Description
Typ.1
Max.2
Unit
IDD_RUN
Run mode current — All functionalities of the chip
available
400
850
mA
IDD_WAIT
Wait mode high frequency current at 3.3 V ± 10%
80
500
mA
3
IDD_LPRUN
Low-power run mode current at 3.3 V ± 10%,
24MHz operation, PLL Bypass.
13
325
mA
4
IDD_ULPRUN
Ultra-low-power run mode current at 3.3 V ± 10%
12
395
mA
5
IDD_STOP
Stop mode current at 3.3 V ± 10%
7
300
mA
6
IDD_LPS3
Low-power stop3 mode current at 3.3 V ± 10%
300
1300
uA
7
IDD_LPS2
Low-power stop 2 mode current at 3.3 V ± 10%
50
875
uA
8
IDD_VBAT
Battery backup mode
5
45
uA
9
Notes
1. The Typ numbers represent the average value taken from a matrix lot of parts across normal process variation at ambient
temperature.
VF3xxR, VF5xxR, Rev7, 11/2014.
20
Freescale Semiconductor, Inc.
LDO electrical specifications
2. The Max numbers represent the single worst case value taken from a matrix lot of parts across normal process variation at
maximum temperature.
3. CA5, CM4 cores halted
4. 24MHz operation, PLL Bypass
5. 32 kHz /128 kHz operation, PLL Off
6. Lowest power mode with all power retained, RAM retention and LVD protection.
7. Standby Mode. 64K RAM retention. I/O states held. ADCs/DACs optionally power-gated. RTC functional. Wakeup from
interrupts. Fast IRC enabled.
8. Standby Mode 16K RAM retention. I/O states held. ADCs/DACs optionally power-gated. RTC functional. Wakeup from
interrupts. Fast IRC enabled.
9. All supplies OFF, SRTC, 32kXOSC ON, tampers and monitors ON. 128k IRC optionally ON.
6.2.5 USB PHY current consumption
6.2.5.1
Power Down Mode
Everything powered down, including the VBUS valid detectors, typ condition.
Table 16. USB PHY Current Consumption in Normal Mode
Current
USBx_VBUS
VDD33_LDOIN
VDD33_LDOIN
(3.0V)
(2.5V)
(1.1V)
Avg
Avg
Avg
5.1 μA
1.7 μA
<0.5 μA
NOTE
The currents on the 2.5 voltage regulator and 3.0 voltage
regulator were identified to be the voltage divider circuits in the
USB-specific level shifters.
6.2.6 EMC radiated emissions operating behaviors
Table 17. EMC radiated emissions operating behaviors
Symbol
VEME
Condition1
Clocks
Device Configuration, test conditions and EM testing
FCPU = 396
per standard IEC 61967-2; Supply voltages: VDD= 5.0 MHz FBUS
V VDD33 = 3.3 V VDD15 = 1.5 V VDD12 = 1.2 V
= 66 MHz
Temp = 25°C
External
Crystal = 24
MHz
Frequency
band 2
Level
(Typ)3
Unit
150 KHz –
50 MHz
22
dBμV
50 MHz –
150 MHz
24
150 MHz –
500 MHz
25
500–1000
20
IEC level4
K
—
1. Measurements were made per IEC 61967-2 while the device was running basic application code.
2. Measurements were performed on the BGA364 version of the device
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
21
I/O parameters
3. The reported emission level is the value of the maximum measured emission, rounded up to the next whole number, from
among the measured orientations in each frequency range.
4. IEC Level Maximums: N ≤ 12dBmV, M ≤ 18dBmV, L ≤ 24dBmV, K ≤ 30dBmV, I ≤ 36dBmV, H ≤ 42dBmV
6.2.7 EMC Radiated Emissions Web Search Procedure boilerplate
To find application notes that provide guidance on designing your system to minimize
interference from radiated emissions:
1. Go to www.freescale.com.
2. Perform a keyword search for “EMC design.”
6.2.8 Capacitance attributes
Table 18. Capacitance attributes
Symbol
Description
Min.
Max.
Unit
CIN_A
Input capacitance:
analog pins
—
7
pF
CIN_D
Input capacitance:
digital pins
—
7
pF
7 I/O parameters
7.1 GPIO parameters
Table 19. GPIO DC operating conditions
Symbol
Parameter
vddi1
Core internal
supply voltage
ovdd
I/O output
supply voltage
Min
Typ
Max
Unit
1.2
3
3.3
V
3.6
V
Max
Unit
1. This is internally controlled.
Table 20. GPIO DC Electrical characteristics
Symbol
Voh
Parameter
High-level
output voltage
Test condition
Ioh= -1mA
Min
Typ
ovdd-0.15
V
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
22
Freescale Semiconductor, Inc.
I/O parameters
Table 20. GPIO DC Electrical characteristics (continued)
Symbol
Parameter
Test condition
Min
Typ
Max
Unit
VOH/VOL
values are with
respect to
DSE=0011
Vol
Low-level output Iol= 1mA
voltage
0.15
V
Vih
High-Level DC
input voltage
0.7*ovdd
ovdd
V
Vil2
Low-Level DC
input voltage
0
0.3*ovdd
V
Vhys
Input Hysteresis ovdd=3.3 V
250
mV
Vt+2
Schmitt trigger
VT+
0.5*ovdd
V
Vt-2, 3
Schmitt trigger
VT-
Iin4
Input current (no Vin = ovdd or 0
pull-up/down)
Iin_22pu
Input current
(22KOhm PU)
Iin_47pu
Input current
(47KOhm PU)
0.5*ovdd
V
1
uA
Vin = 0
212
uA
Vin = ovdd
1
Vin = 0
100
Vin = ovdd
1
Input current
(100KOhm PU)
Vin = 0
50
Vin = ovdd
1
Input current
(100KOhm PD)
Vin = 0
1
Vin = ovdd
50
R_Keeper
Keeper Circuit
Resistance
Vin = 0.3 x
105
OVDD VI = 0.7 x
OVDD
175
Ohm
Issod
Sink current in
open drain
mode
Vin = ovdd
7
mA
Issop
Sink/source
current in Push
Pull mode
Vin = ovdd
7
mA
Iin_100pu
Iin_100pd
-1
1. For details about Software MUX Pad Control Register DSE bit, see IOMUX Controller chapter of the device reference
manual.
2. To maintain a valid level, the transitioning edge of the input must sustain a constant slew rate (monotonic) from the current
DC level through to the target DC level, VIL or VIH. Monotonic input transition time is from 0.1ns to 1s. Vil and Vih do not
apply when hysteresis is enabled.
3. Hysteresis of 250 mV is guaranteed over all operating conditions when hysteresis is enabled.
4. Typ condition: typ model, 3.3V, and 25°C. Max condition: bcs model, 3.6V, and -40°C. Min condition: wcs model, 3.0V and
85 °C. These values are for digital IO buffer cells.
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
23
I/O parameters
Table 21. GPIO AC Electrical Characteristics (3.3V power mode)
Symbol
tpr
Drive strength1
Parameter
IO Output Transition Max 1 1 1
Times (PA1), rise/fall
slow
High 1 0 1
Low 0 1 1
IO Output
Propagation Delay
(PA2), rise/fall
Max 1 1 1
Low 0 1 1
tpv
Output Enable to
Output Valid Delay,
rise/fall
Max 1 1 1
fast
1.69
1.79
slow
3.07
3.31
fast
2.45
2.61
slow
5.13
5.44
fast
4.79
5.18
15pF Cload on pad, 5.01
input edge rate 200ps
3.06
5.04
slow
5.55
5.68
fast
3.52
3.55
slow
6.37
6.67
fast
4.04
4.11
slow
7.39
7.60
fast
5.54
6.10
5.12
5.21
3.18
3.28
5.72
5.80
fast
3.67
3.71
slow
6.55
6.80
fast
4.06
4.09
slow
7.80
8.19
fast
5.72
6.22
1.06
1.31
1.22
1.41
15pF Cload on pad,
input edge rate
200ps, 0->1, 1->0
pad transitions
slow
Low 0 1 1
Input Pad
Propagation Delay
rise/fall
2.44
fast
Medium 1 0 0
tpi
2.30
slow
High 1 0 1
Max
slow
fast
Medium 1 0 0
Min
1.81
slow
High 1 0 1
Test conditions
15pF Cload on pad, 1.70
input edge rate 200ps
1.04
fast
Medium 1 0 0
tpo
Slew
rate
without hysteresis
-
with hysteresis
-
150f Cload on, input
edge rate from pad
=1.2ns
Unit
ns
1.18
ns
3.10
ns
ns
1. The drive strengths are controlled by the DSE bit of the Software MUX Pad Control Register. For details, see IOMUX
Controller chapter of the device reference manual.
7.1.1 Output Buffer Impedance measurement
Table 22. Output Buffer Average Impedance (3.3V power mode)
Symbol
Rdrv
Drive strength1
Parameter
Output driver
impedance
Min
Typ
Max
001
116
150
220
010
58
75
110
011
39
50
73
Unit
Ohm
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
24
Freescale Semiconductor, Inc.
I/O parameters
Table 22. Output Buffer Average Impedance (3.3V power mode) (continued)
Symbol
Drive strength1
Parameter
Min
Typ
Max
100
30
37
58
101
24
30
46
110
20
25
38
17
20
32
Unit
Extra drive strength
111
1. The drive strengths are controlled by the DSE bit of the Software MUX Pad Control Register. For details, see IOMUX
Controller chapter of the device reference manual.
7.2 DDR parameters
Table 23. DDR operating conditions
Symbol
Parameter
Min
Typ
Max
Unit
vddi
Core internal supply voltage
1.16
1.23
1.26
V
ovdd
I/O output supply voltage
(DDR3 mode)
1.425
1.5
1.575
V
ovdd
I/O output supply voltage
(LPDDR2 mode)
1.14
1.2
1.26
V
vdd2p5
I/O PD predriver and level
shifters supply voltage
2.25
2.5
2.75
V
Table 24. LPDDR2 mode DC Electrical characteristics
Symbol
Parameter
Test
condition
Min
Voh
High-level
output voltage
Vol
Low-level
output voltage
Vref
Input
reference
voltage
0.49*ovdd
Vih(dc)
DC input high
voltage
Vil(dc)
Typ
Max
0.9*ovdd
Unit
V
0.1*ovdd
V
0.51*ovdd
V
Vref+0.13
ovdd
V
DC input low
voltage
ovss
Vref-0.13
V
Vih(diff)
DC differential
input logic
high
0.26
Note1
V
Vil(diff)
DC differential
input logic low
Note
-0.26
V
0.5*ovdd
Notes
Note that the
JEDEC
LPDDR2
specification
(JESD209_2B
) supersedes
any
specification
in this
document.
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
25
I/O parameters
Table 24. LPDDR2 mode DC Electrical characteristics (continued)
Symbol
Parameter
Test
condition
Min
Typ
Max
Iin
Input current
(no pull-up/
down)
Vin = ovdd or
0
2.5
Tri-state I/O
supply
current2
Icc-ovdd
Vin = ovdd or
0
4
Vi = vddi or 0
1.5
Tri-state
Icc-vdd2p5
vdd2p5 supply
current2
Tri-state core
supply
current2
Icc-vddi
1
Driver unit
(240 Ohm)
calibration
resolution
Rres
10
Unit
Notes
uA
Ohm
1. The single-ended signals need to be within the respective limits (Vih(dc) max, Vil(dc) min) for single-ended signals as well
as the limitations for overshoot and undershoot.
2. Typ condition: typ model, 1.2 V, and 25 °C junction. Max condition: bcs model, 1.26V, and -40 °C. Min condition: wcs
model, 1.14V, and Tj 125 °C.
Table 25. DDR3 mode DC Electrical characteristics
Symbol
Parameter
Test
condition
Min
Voh
High-level
output voltage
Vol
Low-level
Iol= 1mA
output voltage
Vref
Input
reference
voltage
0.49*ovdd
Vih(dc)
DC input high
voltage
Vil(dc)
Typ
Max
0.8*ovdd
Unit
V
0.2*ovdd
V
0.51*ovdd
V
Vref+0.1
ovdd
V
DC input low
voltage
ovss
Vref-0.1
V
Vih(diff)
DC differential
input logic
high
0.2
Note1
V
Vil(diff)
DC differential
input logic low
Note
-0.2
V
Vtt2
Termination
voltage
Vin = ovdd or
0
Iin
Input current
(no pullup/
pulldown)
Vi = 0 Vi =
ovdd
0.49*ovdd
0.5*ovdd
0.5*ovdd
Notes
Note that the
JEDEC
JESD79_3E
specification
supersedes
any
specification
in this
document
0.51*ovdd
3
uA
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
26
Freescale Semiconductor, Inc.
I/O parameters
Table 25. DDR3 mode DC Electrical characteristics (continued)
Symbol
Tri-state I/O
supply
current3
Parameter
Icc-ovdd
Tri-state
Icc-vdd2p5
vdd2p5 supply
current3
Test
condition
Min
Typ
Max
Vin = ovdd or
0
5
Vi = vddi or 0
1.5
Tri-state core
supply
current3
Icc-vddi
1
Driver unit
(240 Ohm)
calibration
resolution
Rres
10
Unit
Notes
Ohm
1. The single-ended signals need to be within the respective limits (Vih(dc) max, Vil(dc) min) for single-ended signals as well
as the limitations for overshoot and undershoot.
2. Vtt is expected to track ovdd/2.
3. Typ condition: typ model, 1.5 V, and 25 °C. Max condition: bcs model, 1.575V, and -40 °C. Min condition: wcs model,
1.425V, and max Tj °C 125 °C junction
Table 26. LPDDR2 mode AC Electrical characteristics
Symbol
Parameter
Test condition
Vih(ac)
AC input logic
high
Vil(ac)
AC input logic
low
Vidh(ac)
AC differential
input high
voltage
Vidl(ac)1
AC differential
input low voltage
Vix(ac)2
AC differential
Relative to
input crosspoint ovdd/2
voltage
Vpeak
Min
Vref+0.22
Max
Unit
ovdd
V
Vref-0.22
V
-
V
0.44
V
0.12
V
Over/undershoot
peak
0.35
V
Varea
Over/undershoot at 800MHz data
area (above
rate
ovdd or below
ovss)
0.3
V*ns
tsr
Single output
slew rate
2
V/ns
tskd
Skew between
pad rise/fall
asymmetry +
skew cased by
SSN
0.2
ns
0.44
-0.12
0.4
Notes
Note that the
Jedec LPDDR2
specification
(JESD209-2B)
supersedes any
specification in
this document.
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
27
Power supplies and sequencing
1. Vid(ac) specifies the input differential voltage |Vtr-Vcp| required for switching, where Vtr is the “true” input signal and Vcp is
the “complementary” input signal. The Minimum value is equal to Vih(ac)-Vil(ac).
2. The typical value of Vix(ac) is expected to be about 0.5*ovdd, and Vix(ac) is expected to track variation of ovdd. Vix(ac)
indicates the voltage at which differential input signal must cross.
Table 27. DDR3 mode AC Electrical characteristics
Symbol
Parameter
Test condition
Min
Max
Unit
Vih(ac)
AC input logic
high
Vref+0.175
ovdd
V
Vil(ac)
AC input logic
low
ovss
Vref-0.175
V
Vidh(ac)
AC differential
input high
voltage
0.35
-
V
Vidl(ac)1
AC differential
input low voltage
0.35
Vix(ac)2
AC differential
relative to
input crosspoint ovdd/2
voltage
Vref-0.15
Vpeak
Note that the
JEDEC
JESD79_3E
specification
supersedes any
specification in
this document
V
Vref+0.15
V
Over/undershoot
peak
0.4
V
Varea
Over/undershoot at 800 MHz data
area (above
rate
ovdd or below
ovss)
0.5
V*ns
tsr
Single output
slew rate
2
V/ns
tskd
Skew between
pad rise/fall
asymmetry +
skew cased by
SSN
0.2
ns
0.4
Notes
1. Vid(ac) specifies the input differential voltage |Vtr-Vcp| required for switching, where Vtr is the “true” input signal and Vcp is
the “complementary” input signal. The Minimum value is equal to Vih(ac)-Vil(ac).
2. The typical value of Vix(ac) is expected to be about 0.5*ovdd, and Vix(ac) is expected to track variation of ovdd. Vix(ac)
indicates the voltage at which differential input signal must cross.
8 Power supplies and sequencing
8.1 Power sequencing
Table 28. Power sequencing
Power Supply (PKG Board Level
Level)
Power Nets
Parameters
VBAT
Battery supply in case of LDOIN
fails
VBAT
Power
Order
Comment
NA
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
28
Freescale Semiconductor, Inc.
Power supplies and sequencing
Table 28. Power sequencing (continued)
Power Supply (PKG Board Level
Level)
Power Nets
Parameters
Power
Order
VDD33_LDOIN
VDD33
LDO input supply (LDO1P1,
LDO2P5, LDO1P1_RTC)
1
VDDREG
VDD33
Device PMU regulator and
External ballast supply
1
VDD33
VDD33
GPIO 3.3V IO supply, LCD Supply
1
SDRAMC_VDD1P5
SDRAMC_VDD1P5
1.2/1.5 DDR Main IO supply
VDDA33_ADC
VDDA33_ADC
3.3V supply for ADC, DAC and IO
segment
1
VREFH_ADC
VREFH_ADC
High Reference of ADC, DAC
1
VDDA33_AFE
VDDA33_AFE
3.3V supply of AFE (Video ADC)
1
VDD12_AFE
VDD
1.2V supply for AFE (Video ADC)
2
FA_VDD
VDD
Shorted with VDD at Board Level
in 364BGA (Test pin only)
NA
VDD
VDD
1.2V core supply from External
ballast
USB0_VBUS
USB_VBUS
VBUS supply for USB
NA
USB1_VBUS
USB_VBUS
VBUS supply for USB
NA
NA
Comment
VDD33_LDOIN,VDDREG and
VDD33 should come from a
common supply source
(represented as 3.3V SMPS in
the Figure 4)
In case the Ballast transistor’s
collector is connected to the
1.5V DRAM supply (instead of
the 3.3V supply), turn this
1.5V supply on before turning
on the 3.3V.
2
NOTE
NA stands for no sequencing needs, for example, the supply
can come in any order.
NOTE
All supplies grouped together e.g. 1,2, others. These have no
power sequencing restriction in between them.
NOTE
If none of the SDRAMC pins are connected on the board, the
SDRAMC supply could be left floating.
NOTE
At power up, 1.2V supply will follow 3.3V supply. At power
down, it should be checked that 1.2V falls before 3.3V.
NOTE
The standby current on USBx_VBUS is 300 - 500 uA. This is
well below the 2.5 mA limit set by the USB 2.0 specification.
This supply will be ON for applications that need to monitor the
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
29
Power supplies and sequencing
USB bus during standby. This supply can be turned-off during
standby in applications that cannot tolerate the standby current
and do not monitor the USB bus.
8.2 Power supply
10uF
VDDA33_AFE
BCTRL
VDD
4.7uF
VDD
VideoADC
HPREG
LPREG
VDDREG
WELL PD1
48K
16K
WBREG*
3.3V
ULPREG
VDD33_LDOIN
GPIO's
PD0
VDD33
DAC x 2
eFUSE
LDO2P5
SNVS_IO
COIN
cell
Battery supply
(See note)
12-bit SAR
ADC x 2
USB 0/1 PHY
PLLs
DDR IO
SDRAMC_VDD2P5
1.5V/1.2V DDR Supply
SDRAMC_VDD1P5
DECAP_V25_LDO_OUT
LDO1P1
SNVS
LDO
VDDA33_ADC
VREFH_ADC
PLLs
SNVS
LDO3P0
USB_DCAP
DECAP_V11_LDO_OUT
USB0_VBUS (5V)
USB1_VBUS (5V)
Figure 4. Power supply
NOTE
VBAT is the backup battery supply. If not required, then VBAT
should be tied to VDDREG.
VF3xxR, VF5xxR, Rev7, 11/2014.
30
Freescale Semiconductor, Inc.
Power supplies and sequencing
NOTE
WBREG is the Well Bias Regulator. Supplies PD1 WELL
during well bias modes.
8.3 Absolute maximum ratings
NOTE
These are the values above which device can get damaged.
Refer to the recommended operating conditions table for
intended use case values
Table 29. Absolute maximum ratings
Symbol
Parameters
Min
Max
Unit
USB0_VBUS
VBUS supply for USB
-
5.25
V
USB1_VBUS
VBUS supply for USB
-
5.25
V
USB_DCAP
USB LDO 5V->3.3V Outpu
-0.3
3.6
V
VBAT
Battery supply in case of LDOIN
fails
-0.3
3.6
V
VDD33_LDOIN
LDO input supply
-0.3
3.6
V
DECAP_V11_LDO_OUT
LDO 3.3V -> 1.1V Output
-0.3
1.3
V
DECAP_V25_LDO_OUT
LDO 3.3V -> 2.5 Output for PLL,
DDR, EFUSE
-0.3
3.6
V
VDD33
GPIO 3.3V IO supply
-0.3
3.6
V
VDDREG
Device PMU regulator and
External ballast supply
-0.3
3.6
V
VDDA33_ADC
3.3V supply for ADC, DAC and IO
segment
-0.3
3.6
V
VREFH_ADC
3.3V supply of AFE (Video ADC)
-0.3
3.6
V
VDDA33_AFE
3.3V supply of AFE (Video ADC)
-0.3
3.6
V
VDD12_AFE
1.2V supply for AFE (Video ADC)
-0.3
1.3
V
FA_VDD
Test purpose only
-0.3
1.3
V
VDD
1.2V core supply
-0.3
1.3
V
SDRAMC_VDD1P5
1.2/1.5 DDR Main IO supply
-0.3
1.975
V
SDRAMC_VDD2P5
2.5V DDR pre-drive supply
DD2P5_LDO_OUT
-0.3
3.6
V
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
31
Power supplies and sequencing
8.4 Recommended operating conditions
Table 30. Recommended operating conditions
Symbol
Parameters
USB0_VBUS
Conditions
Min
Typ
Max
Unit
VBUS supply for USB
w.r.t USB0_GND
4.4
5
5.25
V
USB1_VBUS
VBUS supply for USB
w.r.t USB1_GND
4.4
5
5.25
V
USB_DCAP
USB LDO 5V->3 V
Output
VBAT
Battery supply in case
of LDOIN fails
VDD33_LDOIN
LDO input supply
External DCAP (10uF
termination for
USBREG)
External CAP 0.1uF
3
V
2.4
3.3
3.6
V
3
3.3
3.6
V
DECAP_V11_LDO_OU LDO 3.3V -> 1.1V
T
Output
Recommended
External DCAP:
1uF(Min) 10uF (Max)
1.1
V
DECAP_V25_LDO_OU LDO 3.3V -> 2.5 Output
T
for PLL, DDR predriver, EFUSE
Recommended
External DCAP:
1uF(Min) 10uF (Max)
2.5
V
VDD33
GPIO 3.3V IO supply
External CAP (10uF)
3
3.3
3.6
V
VDDREG
Device PMU regulator
and External ballast
supply
External CAP (10uF)
3
3.3
3.6
V
VDDA33_ADC
3.3V supply for ADC,
DAC and IO segment
External CAP (10uF)
3
3.3
3.6
V
VREFH_ADC
High reference voltage
for ADC and DAC
Relation with
VDDDA33_ADC (1uF)
2.5
3.3
VDDA33_
ADC
V
VREFL_ADC
Low reference voltage
for ADC and DAC
External CAP (10uF)
VDDA33_AFE
3.3V supply of AFE
(Video ADC)
VDD12_AFE
0
External CAP 10uF
V
3
3.3
3.6
V
1.2V supply for AFE
(Video ADC)
1.16
1.23
1.26
V
FA_VDD
For testing purpose
only should be shorted
to VDD on board.
1.16
1.23
1.26
V
VDD1
1.2V core supply
1.16
1.23
1.26
V
USB0_GND
Ground supply for USB
0
V
USB1_GND
Ground supply for USB
0
V
VSS_KEL0
USB LDO ground
output
0
V
VSS
VSS ground
0
V
VSSA33_ADC
Ground supply for ADC,
DAC and IO segment
0
V
4.7uF with a low ESR
value (100 milliohms)
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
32
Freescale Semiconductor, Inc.
Power supplies and sequencing
Table 30. Recommended operating conditions (continued)
Symbol
Parameters
Conditions
Min
VSSA33_AFE
Ground supply of AFE
(Video ADC)
0
V
VSS12_AFE
Ground supply for AFE
(Video ADC)
0
V
SDRAMC_VDD1P5
LPDDR2
External CAP 10uF
1.142
1.2
1.26
V
SDRAMC_VDD1P5
DDR3
External CAP 10uF
1.425
1.5
1.575
V
SDRAMC_VDD2P5
2.5V DDR pre-drive
supply
DD2P5_LDO_OUT
External CAP 10uF
2.25
2.5
2.75
V
-
Maximum power supply
ramp rate (Slew limit for
power-up)
0.1
V/us
-
Typ
Max
Unit
1. For customer applications, this is governed by ballast output which is controlled by the device and appropriate voltage
ranges are maintained.
8.5 Recommended Connections for Unused Analog Interfaces
NOTE
There are two options to handle unused power pins:
1. Connect all unused supplies to their respective voltage. To
save the power, do not enable the module and/or do not
enable clock gate to the module.
2. Keep all unused supplies floating.
If pin is shared by several peripheral, then all peripherals
connected to multiplexer have to be powered. For example: if
pin is shared by GPIO and ADC input and GPIO functionality
is used, then ADC has to be powered due to internal structure of
the multiplexer. Keep unused input signals grounded if power
pins are powered. Keep unused input signals floating if power
pins are floating. Keep unused output signals floating.
Module
Name
Recommendation if Unused
ADC
VDDA33_ADC
3.3V or float (Note: Powers both ADC
and DAC)
VREFH_ADC, VREFL_ADC
VREFH_ADC same as VDDA33_ADC
VREFL_ADC ground or float
ADC0SE8, ADC0SE9, ADC1SE8,
ADC1SE9
Ground or float
CCM
LVDS0P, LVDS0N
Float
DAC
DACO0, DACO1
Float
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
33
Peripheral operating requirements and behaviours
Module
Name
Recommendation if Unused
USB
USB_DCAP, USB0_VBUS,
USB1_VBUS
Connect USBx_VBUS and USB_DCAP
together and tie to ground through a 10K
ohm resistor. Do NOT tie directly to
ground, latch-up risk.
USB0_GND, USB1_GND
Ground
USB0_VBUS_DETECT,
USB1_VBUS_DETECT
Float
USB0_DM, USB0_DP, USB1_DM,
USB1_DP
Float
VDDA33_AFE
3.3V or Float
VDD12_AFE
1.2V or Float
Video ADC
VADC_AFE_BANDGAP
Float
VADCSE0, VADCSE1, VADCSE2,
VADCSE3
Ground or Float
9 Peripheral operating requirements and behaviours
9.1 Analog
9.1.1 12-bit ADC electrical characteristics
9.1.1.1
12-bit ADC operating conditions
Characteristic
Table 31. 12-bit ADC Operating Conditions
Conditions
Symb
Min
Typ
Max
Unit
Comment
1
Supply voltage
Absolute
VDDAD
2.5
-
3.6
V
-
Delta to VDDAD (VDDVDDAD)
ΔVDDAD
-100
0
100
mV
-
Ground voltage
Delta to VSSAD (VSSVSSAD)2
ΔVSSAD
-100
0
100
mV
-
Ref Voltage High
-
VREFH
1.5
VDDAD
VDDAD
V
-
Ref Voltage Low
-
VREFL
VSSAD
VSSAD
VSSAD
V
-
Input Voltage
-
VADIN
VREFL
-
VREFH
V
-
Input Capacitance
8/10/12 bit modes
CADIN
-
1.5
2
pF
-
Input Resistance
ADLPC=0, ADHSC=1
RADIN
-
5
7
kohms
-
ADLPC=0, ADHSC=0
-
12.5
15
kohms
-
ADLPC=1, ADHSC=0
-
25
30
kohms
-
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
34
Freescale Semiconductor, Inc.
Analog
Table 31. 12-bit ADC Operating Conditions (continued)
Characteristic
Conditions
Symb
Min
Typ
Max
Unit
Comment
1
kohms
Tsamp=150
ns
1
Analog Source
Resistance
12 bit mode fADCK =
40MHz ADLSMP=0,
ADSTS=10, ADHSC=1
RAS
-
-
RAS depends on Sample Time Setting (ADLSMP, ADSTS) and ADC Power Mode (ADHSC, ADLPC). See charts for Minimum
Sample Time vs RAS
ADC Conversion Clock
Frequency
ADLPC=0, ADHSC=1
12 bit mode
fADCK
4
-
40
MHz
-
ADLPC=0, ADHSC=0
12 bit mode
4
-
30
MHz
-
ADLPC=1, ADHSC=0
12 bit mode
4
-
20
MHz
-
1. Typical values assume VDDAD = 3.3 V, Temp = 25°C, fADCK=20 MHz unless otherwise stated. Typical values are for
reference only and are not tested in production.
2. DC potential difference
Simplified input pin
equivalent circuit
Pad
leakage
due to
input
protection
ZAS
RAS
VAS
+
–
CAS
ZADIN
Simplified channel
select circuit
RADIN
ADC SAR
engine
+
VADIN
–
RADIN
Input pin
Input pin
RADIN
RADIN
Input pin
CADIN
Figure 5. 12-bit ADC Input Impedance Equivalency Diagram
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
35
Analog
9.1.1.2
12-bit ADC characteristics
Table 32. 12-bit ADC Characteristics (VREFH = VDDAD, VREFL = VSSAD)
Characteristic
Conditions
Symb
Supply Current
ADLPC=1, ADHSC=0
IDDAD
Min
Typ
250
ADLPC=0, ADHSC=0
350
ADLPC=0, ADHSC=1
400
Supply Current
Stop, Reset, Module
Off
IDDAD
0.01
ADC Asynchronous
Clock Source
ADHSC=0
fADACK
10
Sample Cycles
ADLSMP=0,
ADSTS=00
Conversion Cycles
Conversion Time
ADHSC=1
Csamp
2
4
ADLSMP=0,
ADSTS=10
6
ADLSMP=0,
ADSTS=11
8
ADLSMP=1,
ADSTS=00
12
ADLSMP=1,
ADSTS=01
16
ADLSMP=1,
ADSTS=10
20
ADLSMP=1,
ADSTS=11
24
Cconv
28
ADLSMP=0
ADSTS=01
30
ADLSMP=0
ADSTS=10
32
ADLSMP=0
ADSTS=11
34
ADLSMP=1
ADSTS=00
38
ADLSMP=1
ADSTS=01
42
ADLSMP=1
ADSTS=10
46
ADLSMP=1,
ADSTS=11
50
ADLSMP=0
ADSTS=00
ADLSMP=0
ADSTS=01
0.8
Unit
Comment
µA
ADLSMP=0
ADSTS=10 ADCO=1
µA
MHz
tADACK = 1/fADACK
20
ADLSMP=0,
ADSTS=01
ADLSMP=0
ADSTS=00
Max
Tconv
0.7
cycles
cycles
µs
Fadc=40 MHz
0.75
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
36
Freescale Semiconductor, Inc.
Analog
Table 32. 12-bit ADC Characteristics (VREFH = VDDAD, VREFL = VSSAD) (continued)
Characteristic
Total Unadjusted
Error
Conditions
Symb
0.8
ADLSMP=0
ADSTS=11
0.85
ADLSMP=1
ADSTS=00
0.95
ADLSMP=1
ADSTS=01
1.05
ADLSMP=1
ADSTS=10
1.15
ADLSMP=1,
ADSTS=11
1.25
12 bit mode
Comment
LSB
With Max Averaging
LSB1
Waiting for histogram
method confirmation
LSB1
Waiting for histogram
method confirmation
LSB1
VADIN = VREFL With
Max Averaging
LSB1
VADIN = VREFH With
Max Averaging
+5
10 bit mode
-0.5
-
+2
8 bit mode
-0.25
-
+1.5
-
±0.6
±1.5
-
±0.5
±1
-
±0.25
±0.5
-
±2
±4
10bit mode
-
±1
±2
8 bit mode
-
±0.5
±1
-
+1.0
±1.6
10bit mode
-
±0.4
±0.8
8 bit mode
-
±0.1
±0.4
-
±2
±3.5
12 bit mode
DNL
10bit mode
8 bit mode
Quantization Error
Unit
-
Integral Non-Linearity
TUE
Max
-2
12 bit mode
Full-Scale Error
Typ
ADLSMP=0
ADSTS=10
Differential NonLinearity
Zero-Scale Error
Min
INL
12 bit mode
EZS
12 bit mode
EFS
10bit mode
-
±0.5
±1
8 bit mode
-
±0.25
±0.75
-
±1 to 0
10bit mode
-
±0.5
8 bit mode
-
±0.5
10.1
10.7
12 bit mode
EQ
LSB1
Effective Number of
Bits
12 bit mode
ENOB
-
Bits
Signal to Noise plus
Distortion
See ENOB
SINAD
SINAD = 6.02 x ENOB + 1.76
dB
Input Leakage Error
all modes
EIL
IIn x RAS
mV
Temp Sensor Slope
Across the full
temperature range of
the device
m
--
1.84
--
mV/°C
Temp Sensor Voltage
25°C
VTEMP25
-
696
-
mV
Fin = 100Hz
IIn = 400 nA leakage
current
1. 1 LSB = (VREFH - VREFL)/2N
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
37
Analog
NOTE
The ADC electrical spec would be met with the calibration
enabled configuration.
Figure 6. Minimum Sample Time Vs Ras (Cas = 2pF)
Figure 7. Minimum Sample Time Vs Ras (Cas = 5pF)
VF3xxR, VF5xxR, Rev7, 11/2014.
38
Freescale Semiconductor, Inc.
Analog
Figure 8. Minimum Sample Time Vs Ras (Cas = 10pF)
9.1.2 12-bit DAC electrical characteristics
9.1.2.1
12-bit DAC operating requirements
Table 33. 12-bit DAC operating requirements
Symbol
Desciption
Min.
Typ
Max.
Unit
Notes
VDDA33_ADC
Supply voltage
3.0
3.3
3.6
V
VREFH_ADC
Reference voltage
2.5
3.3
VDDA33_
ADC
V
1
CL
Output load capacitance
—
100
pF
2
IL
Output load current
—
1
mA
1. User will need to set up DACx_STATCTRL [DACRFS]=1 to select the valid VREFH_ADC reference. When
DACx_STATCTRL [DACRFS]=0, the DAC reference is connected to an internal ground node and is not a valid voltage
reference. Note that the DAC and ADC share the VREFH_ADC reference simultaneously. )
2. A small load capacitance (47 pF) can improve the bandwidth performance of the DAC
9.1.2.2
Symbol
12-bit DAC operating behaviors
Table 34. 12-bit DAC operating behaviors
Description
IDDA_DACL Supply current — low-power mode
Min.
Typ.
Max.
Unit
—
—
100
μA
—
—
500
μA
—
10
15
μs
Notes
P
IDDA_DACH Supply current — high-power mode
P
tDACLP
Full-scale settling time (0x080 to 0xF7F) —
low-power mode
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
39
Analog
Table 34. 12-bit DAC operating behaviors (continued)
Symbol
Description
tDACHP
Full-scale settling time (0x080 to 0xF7F) —
high-power mode
Min.
Typ.
Max.
Unit
Notes
—
3
5
μs
1
μs
1
tCCDACLP Code-to-code settling time (0xBF8 to 0xC08)
low-power mode
—
5
—
high-power mode
—
1
—
Vdacoutl
DAC output voltage range low — high-speed
mode, no load, DAC set to 0x000
—
—
100
mV
Vdacouth
DAC output voltage range high — highspeed mode, no load, DAC set to 0xFFF
VDACR
−100
—
VDACR
mV
INL
Integral non-linearity error — high speed
mode
—
—
±8
LSB
2
DNL
Differential non-linearity error — VDACR =
VREF_OUT
—
—
±1
LSB
3
—
±0.4
±0.8
%FSR
—
±0.1
±0.6
%FSR
VOFFSET Offset error
EG
PSRR
Power supply rejection ratio, VDDA =3 V, T =
25 C
70
TCO
Temperature coefficient offset voltage
—
3.7
TGE
Temperature coefficient gain error
—
AC
Offset aging coefficient
—
Rop
Output resistance load = 3 kΩ
—
SR
Slew rate -80h→ F7Fh→ 80h
CT
1.
2.
3.
4.
Gain error
dB
—
μV/C
0.000421
—
%FSR/C
—
100
μV/yr
—
250
Ω
V/μs
High power (SPHP)
1.7
3
Low power (SPLP)
0.3
0.6
Channel to channel cross talk
4
—
70
dB
Settling within ±1 LSB
The INL is measured for 0+100mV to VDACR−100 mV
The DNL is measured for 0+100mV to VDACR−100 mV
Calculated by a best fit curve from VSS+100 mV to VDACR−100 mV
VF3xxR, VF5xxR, Rev7, 11/2014.
40
Freescale Semiconductor, Inc.
Analog
Figure 9. INL error vs. digital code
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
41
Analog
Figure 10. DNL error vs. digital code
VF3xxR, VF5xxR, Rev7, 11/2014.
42
Freescale Semiconductor, Inc.
Analog
Figure 11. Offset at half scale vs. temperature
9.1.3 VideoADC Specifications
This section describes the electrical specification and characteristics of the VideoADC
Analog Front End.
Table 35. VideoADC Specifications
Symbol
VDDA33_AFE
VDDA12_AFE
Vin
Description
Min.
Typ.
Max.
Unit
Notes
Supply voltage
3.0
3.3
3.6
V
—
Supply current
—
—
41
mA
—
Supply voltage
1.1
1.2
1.26
V
—
Supply current
—
—
14
mA
—
Input signal voltage range
0.5
0
External AC coupling
10
—
1.4
47
V
nF
The external AC coupling
capacitance cannot be too large.
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
43
Analog
Table 35. VideoADC Specifications (continued)
Symbol
Description
VBG
Bandgap voltage
VDDA33_AFE
—
Typ.
0.6
VSSA33_AFE VDD12_AFE
100nF
(See notes)
VADC_AFE_BANDGAP
Min.
Max.
—
Unit
V
47nF
47nF
100nF
(See notes)
Band Gap
47nF
47nF
Mux,
Clamp
and
Filter
Bandgap voltage on
VADC_AFE_BANDGAP pin. Pin
should be decoupled with a 100nF
capacitor
VSS12_AFE
Control
Interface
100nF
VADCSE0
VADCSE1
VADCSE2
VADCSE3
Notes
ADC
Correction
To Video
Decoder
Figure 12. VideoADC supply scheme
Figure 13. VideoADC supply decoupling
VF3xxR, VF5xxR, Rev7, 11/2014.
44
Freescale Semiconductor, Inc.
Display and Video interfaces
NOTE
VideoADC 3.3V and 1.2V power supply pins should be
decoupled to their respective grounds using low-ESR 100nF
capacitors
NOTE
If possible, avoid using switched voltage regulators for the AFE
power domains. Use linear voltage regulators instead.
NOTE
The 3.3V and 1.2V power domains should be separated from
other circuitry on the board by inductors/beads to filter out high
frequency noise.
9.2 Display and Video interfaces
9.2.1 DCU Switching Specifications
9.2.1.1
Interface to TFT panels (DCU0/1)
This section provides the LCD interface timing for a generic active matrix color TFT
panel. In the figure below, signals are shown with positive polarity. The sequence of
events for active matrix interface timing:
• PCLK latches data into the panel on its positive edge (when positive polarity is
selected). In active mode, PCLK runs continuously. This signal frequency could be
from 5 to 66 MHz depending on the panel type.
• HSYNC causes the panel to start a new line. It always encompasses at least one
PCLK pulse.
• VSYNC causes the panel to start a new frame. It always encompasses at least one
HSYNC pulse.
• DE acts like an output enable signal to the LCD panel. This output enables the data
to be shifted onto the display. When disabled, the data is invalid and the trace is off.
Figure 14. TFT LCD interface timing overview1
1.
In the figure, LD[23:0]” signal is “line data,” an aggregation of the DCU’s RGB signals—R[0:7], G[0:7] and B[0:7].
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
45
DCU Switching Specifications
VSYNC
HSYNC
LINE 1
LINE 2
LINE 3
LINE
n-1
LINE 4
LINE n
HSYNC
DE
1
2
3
m-1
m
PCLK
LD[23:0]
9.2.1.2
Interface to TFT LCD Panels—Pixel Level Timings
This section provides the horizontal timing (timing of one line), including both the
horizontal sync pulse and data. All parameters shown in the figure below are
programmable. This timing diagram corresponds to positive polarity of the PCLK signal
(meaning the data and sync signals change on the rising edge) and active-high polarity of
the HSYNC, VSYNC and DE signals. The user can select the polarity of the HSYNC and
VSYNC signals via the SYN_POL register, whether active-high or active-low. The
default is active-high. The DE signal is always active-high. Pixel clock inversion and a
flexible programmable pixel clock delay are also supported. They are programmed via
the clock divide . The DELTA_X and DELTA_Y parameters are programmed via the
DISP_SIZE register. The PW_H, BP_H and FP_H parameters are programmed via the
HSYN PARA register. The PW_V, BP_V and FP_V parameters are programmed via the
VSYN_PARA register.
Table 36. LCD interface timing parameters—horizontal and vertical
Symbol
Characteristic
Unit
tPCP
Display pixel clock period
11.2
ns
tPWH
HSYNC pulse width
PW_H * tPCP
ns
tBPH
HSYNC back porch width
BP_H * tPCP
ns
tFPH
HSYNC front porch width
FP_H * tPCP
ns
tSW
Screen width
DELTA_X * tPCP
ns
tHSP
HSYNC (line) period
(PW_H + BP_H + FP_H + DELTA_X ) * tPCP
ns
tPWV
VSYNC pulse width
PWV * tHSP
ns
tBPV
VSYNC back porch width
BP_V * tHSP
ns
tFPV
VSYNC front porch width
FP_V * tHSP
ns
tSH
Screen height
DELTA_Y * tHSP
ns
tVSP
VSYNC (frame) period
(PW_V + BP_V + FP_V + DELTA_Y ) * tHSP
ns
VF3xxR, VF5xxR, Rev7, 11/2014.
46
Freescale Semiconductor, Inc.
DCU Switching Specifications
tHSP
Start
of line
tPWH
tBPH
tSW
tFPH
tPCP
PCLK
Invalid Data
LD[23:0]
1
3
2
Invalid Data
DELTA_X
HSYNC
DE
Figure 15. Horizontal sync timing
tVSP
Start of
Frame
tPWV
tBPV
tSH
tFPV
tHCP
HSYNC
LD[23:0]
(Line Data)
Invalid Data
1
2
3
Invalid Data
DELTA_Y
HSYNC
DE
Figure 16. Vertical sync pulse
9.2.1.3
Interface to TFT LCD panels—access level
This section provides the access level timing parameters of the LCD interface.
Table 37. LCD Interface Timing Parameters1, 2, 3—Access Level
Symbol
Description
Min
Max
Unit
tCKP
Pixel Clock Period
11.2
_
ns
tDV
TFT interface data valid after pixel clock
_
4.4
ns
tDV
TFT interface HSYNC valid after pixel clock
_
4.4
ns
tDV
TFT interface VSYNC valid after pixel clock
_
4.4
ns
tDV
TFT interface DE valid after pixel clock
_
4.4
ns
tHO
TFT interface output hold time for data and control bits
0
_
ns
Relative skew between the data bits
_
4.4
ns
1. The characteristics in this table are based on the assumption that data is output at +ve edge and displays latch data on -ve
edg6
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
47
DCU Switching Specifications
2. Intra bit skew is less than 2 ns
3. Load CL = 50 pf
tHO
tDV
Figure 17. LCD Interface Timing Parameters—Access Level
9.2.2 Video Input Unit timing
This section provides the timing parameters of the Video Input Unit (VIU) interface.
tSU tHO
Figure 18. VIU Timing Parameters
Table 38. VIU Timing Parameters
Symbol
Characteristic
Min Value
Max Value
Unit
fPIX_CK
VIU pixel clock frequency
_
64
MHz
tDSU
VIU data setup time
4
_
ns
tDHD
VIU data hold time
1
_
ns
VF3xxR, VF5xxR, Rev7, 11/2014.
48
Freescale Semiconductor, Inc.
Ethernet specifications
9.2.3 LCD driver electrical characteristics
This section provides LCD driver electrical specification at VDD33 = 3.3 V ± 10%.
Table 39. LCD driver specifications
Symbol
Parameter
Min
VLCD
Voltage on VLCD (LCD supply) pin with
respect to VSS
0
ZBP/FP
LCD output impedance
(BP[n-1:0],FP[m-1:0]) for output levels
VDDE, VSS
_
IBP/FP
LCD output current (BP[n-1:0],FP[m-1:0]) for _
outputs charge/discharge voltage levels
VDDE2/3, VDDE1/2, VDDE/3)1
Typical
Max
Unit
VDD33 +
0.3
V
_
5.0
KΩ
25
_
µA
1. With PWR=10, BSTEN=0, and BSTAO=0
9.3 Ethernet specifications
9.3.1 Ethernet Switching Specifications
The following timing specs are defined at the chip I/O pin and must be translated
appropriately to arrive at timing specs/constraints for the physical interface. All Ethernet
signals use pad type pad_fsr. The timing specifications described i the section assume a
pad slew rate setting of 11 and a load of 50 pF2.
9.3.2 Receive and Transmit signal timing specifications
This section provides timing specs that meet the requirements for RMII interfaces for a
range of transceiver devices.
Table 40. Receive signal timing for RMII interfaces
Characteristic
RMII Mode
Min
Unit
Max
—
EXTAL frequency (RMII input clock RMII_CLK)
—
50
MHz
E3, E7
RMII_CLK pulse width high
35%
65%
RMII_CLK period
Table continues on the next page...
2.
These timing parameters are specified assuming maximum operating frequency and the fastest pad slew rate setting (11).
When operating this interface at lower frequencies, increase the slew rate by using the 10, 01, or 00 setting to increase
edge rise and fall times, thus reducing EMI.
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
49
Ethernet specifications
Table 40. Receive signal timing for RMII interfaces (continued)
Characteristic
RMII Mode
Min
Unit
Max
E4, E8
RMII_CLK pulse width low
35%
65%
RMII_CLK period
E1
RXD[1:0], CVS_DV, RXER to RMII_CLK setup
4
—
ns
E2
RMII_CLK to RXD[1:0], CRS_DV, RXER hold
2
—
ns
E6
RMII_CLK to TXD[1:0], TXEN valid
—
14
ns
E5
RMII_CLK to TXD[1:0], TXEN invalid
4
—
ns
Figure 19. RMII receive signal timing diagram
Figure 20. RMII transmit signal timing diagram
NOTE
See the most current device errata document when using the
internally generated RXCLK and TXCLK clocks.
VF3xxR, VF5xxR, Rev7, 11/2014.
50
Freescale Semiconductor, Inc.
Ethernet specifications
tCYC
tPWH
RX_CLK
(Input)
tS
tH
RXDn,
RX_DV,
RX_ER
(Input)
(n = 0-3)
Figure 21. MII receive signal timing diagram
Table 41. Receive signal timing for MII interfaces
Characteristic
MII Mode
Min
RX_CLK clock period (100/10 MBPS) tCYC
RX_CLK duty cycle, tPWH/tCYC
Typ
Unit
Max
40/400
45
50
ns
55
%
Input setup time before RX_CLK
tS
5
ns
Input setup time after RX_CLK
tH
5
ns
9.3.3 Receive and Transmit signal timing specifications for MII
interfaces
This section provides timing specs that meet the requirements for MII interfaces for a
range of transceiver devices.
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
51
Ethernet specifications
tCYC
tPWH
RX_CLK
(Input)
tS
tH
RXDn,
RX_DV,
RX_ER
(Input)
(n = 0-3)
Figure 22. MII receive signal timing diagram
Table 42. Receive signal timing for MII interfaces
Characteristic
MII Mode
Min
RX_CLK clock period (100/10 MBPS) tCYC
Unit
Typ
Max
40/400
RX_CLK duty cycle, tPWH/tCYC
45
ns
50
55
%
Input setup time before RX_CLK
ts
5
ns
Input hold time after RX_CLK
th
5
ns
tCYC
tPWH
TX_CLK
(Input)
tD
TXDn,
TX_EN,
TX_ER
(Output)
Note: Device pins applicable to MII interface are applicable to TMII interface,
and operates at 50 MHz reference clock.
Figure 23. MII transmit signal timing diagram
Table 43. Transmit signal timing for MII interfaces
Characteristic
MII Mode
Min
TX_CLK clock period (100/10 MBPS) tCYC
TX_CLK duty cycle, tPWH/tCYC
Out delay from TX_CLK
Max
40/400
45
tD
Typ
Unit
2
50
ns
55
%
25
ns
VF3xxR, VF5xxR, Rev7, 11/2014.
52
Freescale Semiconductor, Inc.
Audio interfaces
9.4 Audio interfaces
9.4.1 Enhanced Serial Audio Interface (ESAI) Timing Parameters
The ESAI consists of independent transmitter and receiver sections, each section with its
own clock generator. The following table shows the interface timing values.
Table 44. Enhanced Serial Audio Interface (ESAI) Timing
No
1
2
Characteristics
Clock
cycle2
Clock high period:
• master
• slave
Symbol
Min
Max
Condition1
Unit
tSSICC
30.0
—
master
ns
(4 × Tc)
—
—
—
ns
—
—
—
—
—
—
—
6
—
(2 × Tc −
9.0)
15
(2 × Tc)
3
Clock low period:
• master
• slave
—
FSR Input and Data Input setup time before SCKR
(SCK in synchronous mode) falling edge
—
6
—
Slave
—
15
—
Master
FSR Input and Data Input hold time after SCKR
falling edge
—
2
—
Slave
—
0
—
Master
6
SCKT rising edge to FST out and Data out valid
—
—
15
Slave
—
—
6
Master
7
SCKT rising edge to FST out and Data out hold
—
—
0
Slave
—
—
0
Master
8
FST input setup time before SCKT falling edge
—
6
—
Slave
—
15
—
Master
9
FST input hold time after SCKT falling edge
—
2
—
Slave
—
0
—
Master
10
HCKR/HCKT clock cycle
—
15
—
—
ns
11
HCKT input rising edge to SCKT output
—
—
18.0
—
ns
12
HCKR input rising edge to SCKR output
—
—
18.0
—
ns
4
5
—
6 (2 × Tc −
9.0)
ns
15 (2 × Tc)
ns
ns
ns
ns
ns
ns
(2 x TC)
1. SCKT(SCKT pin) = transmit clock SCKR(SCKR pin) = receive clock FST(FST pin) = transmit frame sync FSR(FSR pin) =
receive frame sync HCKT(HCKT pin) = transmit high frequency clock HCKR(HCKR pin) = receive high frequency clock
2. For the internal clock, the external clock cycle is defined by Icyc and the ESAI control register.
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
53
Audio interfaces
1
2
3
SCKT
(input/output)
FST (bit) out
6
FST (word) out
First bit
Data out
Last
Lastbitbit
9
FST (bit) in
9
8
FST (word) in
Figure 24. ESAI Transmitter Timing
1
2
SCKR
(input/output)
3
FSR (bit) out
FSR (word) out
5
4
Data in
First bit
Last bit
FSR (bit) in
FSR (word) in
Figure 25. ESAI Receiver Timing
VF3xxR, VF5xxR, Rev7, 11/2014.
54
Freescale Semiconductor, Inc.
Audio interfaces
9.4.2 SPDIF Timing Parameters
The Sony/Philips Digital Interconnect Format (SPDIF) data is sent using the bi-phase
marking code. When encoding, the SPDIF data signal is modulated by a clock that is
twice the bit rate of the data signal. Table and Figure below show SPDIF timing
parameters for the Sony/Philips Digital Interconnect Format (SPDIF), including the
timing of the modulating Rx clock (SRCK) for SPDIF in Rx mode and the timing of the
modulating Tx clock (STCLK) for SPDIF in Tx mode.
Table 45. SPDIF Timing Parameters
Characteristic
Symbol
Timing Parameter Range
Min
SPDIFIN Skew: asynchronous inputs, no specs apply
Max
0.7
SPDIFOUT output (Load = 50pf)
• Skew
• Transition rising
• Transition falling
ns
• 1.5
• 24.2
• 31.3
SPDIFOUT1 output (Load = 30pf) - Skew
1.5
• Transition rising
• Transition falling
Unit
ns
ns
Refer Table 21
Modulating Rx clock (SRCK) period
srckp
40
ns
SRCK high period
srckph
16
ns
SRCK low period
srckpl
16
ns
Modulating Tx clock (STCLK) period
stclkp
40
ns
STCLK high period
stclkph
16
ns
STCLK low period
stclkpl
16
ns
Figure 26. SRCK Timing Diagram
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
55
Audio interfaces
Figure 27. STCLK Timing Diagram
9.4.3 SAI/I2S Switching Specifications
This section provides the AC timings for the SAI in master (clocks driven) and slave
modes (clocks input). All timings are given for non-inverted serial clock polarity
(SAI_TCR[TSCKP] = 0, SAI_RCR[RSCKP] = 0) and a non-inverted frame sync
(SAI_TCR[TFSI] = 0, SAI_RCR[RFSI] = 0). If the polarity of the clock and/or the frame
sync have been inverted, all the timings remain valid by inverting the clock signal
(SAI_BCLK) and/or the frame sync (SAI_FS) shown in the figures below.
Table 46. Master Mode SAI Timing
Num
Characteristic
Min
Max
Unit
S1
SAI_MCLK cycle time
2 x tSYS
—
ns
S2
SAI_MCLK pulse width high/low
40%
60%
MCLK period
S3
SAI_BCLK cycle time
4 x tSYS
—
ns
S4
SAI_BCLK pulse width high/low
40%
60%
BCLK period
S5
SAI_BCLK to SAI_FS output valid
—
15
ns
S6
SAI_BCLK to SAI_FS output invalid
0
—
ns
S7
SAI_BCLK to SAI_TXD valid
—
15
ns
S8
SAI_BCLK to SAI_TXD invalid
0
—
ns
S9
SAI_RXD/SAI_FS input setup before SAI_BCLK
15
—
ns
S10
SAI_RXD/SAI_FS input hold after SAI_BCLK
0
—
ns
VF3xxR, VF5xxR, Rev7, 11/2014.
56
Freescale Semiconductor, Inc.
Audio interfaces
S1
S2
S2
I2S_MCLK (output)
S3
I2S_BCLK (output)
S4
S4
S6
S5
I2S_FS (output)
S10
S9
I2S_FS (input)
S7
S8
S7
S8
I2S_TXD
S9
S10
I2S_RXD
Figure 28. SAI Timing — Master Modes
Table 47. Slave Mode SAI Timing
Num
Characteristic
Min
Max
Unit
S11
SAI_BCLK cycle time (input)
4 x tSYS
—
ns
S12
SAI_BCLK pulse width high/low (input)
40%
60%
BCLK period
S13
SAI_FS input setup before SAI_BCLK
10
—
ns
S14
SAI_FS input hold after SAI_BCLK
2
—
ns
S15
SAI_BCLK to SAI_TXD/SAI_FS output valid
—
20
ns
S16
SAI_BCLK to SAI_TXD/SAI_FS output invalid
0
—
ns
S17
SAI_RXD setup before SAI_BCLK
10
—
ns
S18
SAI_RXD hold after SAI_BCLK
2
—
ns
S11
S12
I2S_BCLK (input)
S12
S15
S16
I2S_FS (output)
S13
S14
I2S_FS (input)
S15
S16
S15
S16
I2S_TXD
S17
S18
I2S_RXD
Figure 29. SAI Timing — Slave Modes
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
57
Memory interfaces
9.5 Memory interfaces
9.5.1 QuadSPI timing
• All data is based on a negative edge data launch from the device and a negative edge
data capture, as shown in the timing diagrams in this section. This corresponds to the
N/1 sample point as shown in the reference manual QSPI section "Internal Sampling
of Serial Flash Input Data."
• Measurements are with a load of 35 pF on output pins. I/P Slew : 1ns
• Timings assume a setting of 0x0000_000x for QSPI_SMPR register (see the
reference manual for details).
SDR mode
Tck
SCK
Tcss
Tcsh
CS
Tis
Tih
Data in
Figure 30. QuadSPI Input/Read timing (SDR mode)
Table 48. QuadSPI Input/Read timing (SDR mode)
Symbol
Parameter
Value
Min
Unit
Max
Tis
Setup time for incoming data
4.5
—
ns
Tih
Hold time requirement for incoming data
0
—
ns
VF3xxR, VF5xxR, Rev7, 11/2014.
58
Freescale Semiconductor, Inc.
Memory interfaces
Tck
SCK
Tcss
Tcsh
CS
Toh
Tov
Data out
Figure 31. QuadSPI Output/Write timing (SDR mode)
Table 49. QuadSPI Output/Write timing (SDR mode)
Symbol
Parameter
Value
Min
Unit
Max
Tov
Output Data Valid
-
3.2
ns
Toh
Output Data Hold
0
-
ns
Tck
SCK clock period
-
80
MHz
Tcss
Chip select output setup time
3
-
SCK clock cycles
Tcsh
Chip select output hold time
3
-
SCK clock cycles
•
•
•
•
•
NOTE
Tcss and Tcsh are set by QuadSPI_FLSCH register, the
minimum values of 3 shown are the register default values,
refer to Reference Manual for further details.
The timing in the datasheet is based on default values for
the QuadSPI-SMPR register and is the recommended
setting for highest SCK frequency in SDR mode.
A negative time indicates the actual capture edge inside the
device is earlier than clock appearing at pad.
Frequency calculator guideline (Max read frequency): SCK
> (Flash access time)max + (Tis)max
A negative input hold time has no bearing on the maximum
achievable operating frequency.
DDR Mode
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
59
Memory interfaces
Tck
SCK
Tcss
Tcsh
CS
Tih
Tis
Data in
Figure 32. QuadSPI Input/Read timing (DDR mode)
•
•
•
•
•
NOTE
The numbers are for a setting of 0x1 in regiater
QuadSPI_SMPR[DDRSMP]
Read frequency calculations should be: SCK/2 > (flash
access time) + Setup (Tis) (QuadSPI_SMPR[DDRSMP])x SCK/4
Frequency calculator guideline (Max read frequency):
SCK/2 > (Flash access time)max + (Tis)max (QuadSPI_SMPR[DDRSMP]) xSCK/4
Hold timing: flash_access (min) + flash_data_valid (min) >
SCK/2 + HOLD(Tih) +
(QuadSPI_SMPR[DDRSMP])SCK/4
A negative time indicates the actual capture edge inside the
device is earlier than clock appearing at pad.
Table 50. QuadSPI Input/Read timing (DDR mode)
Symbol
Parameter
Value
Min
Unit
Max
Tis
Setup time for incoming data
6.4
—
ns
Tih
Hold time requirement for incoming data
-3.0
—
ns
NOTE
VF3xxR, VF5xxR, Rev7, 11/2014.
60
Freescale Semiconductor, Inc.
Memory interfaces
Tck
SCK
Tcss
Tcsh
CS
Tov
Toh
Data out
Figure 33. QuadSPI Output/Write timing (DDR mode)
Table 51. QuadSPI Output/Write timing (DDR mode)
Symbol
Parameter
Value
Min
Unit
Max
Tov
Output Data Valid
—
3.2
ns
Toh
Output Data Hold
0
—
ns
Tck
SCK clock period
-
45
MHz
Tcss
Chip select output setup time
3
-
Clk(sck)
Tcsh
Chip select output hold time
3
-
Clk(sck)
9.5.2 NFC specifications
The NAND flash controller (NFC) implements the interface to standard NAND flash
memory devices. This section describes the timing parameters of the NFC.
In the following table:
• TH is the flash clock high time and
• TL is flash clock low time,
which are defined as:
TNFC = TH + TL
NOTE
Refer to the Reference Manual for further details on setting up
the NFC clocks (CCM_CSCDR2[NFC_FRAC_DIV_EN +
NFC_FRAC_DIV] and CCM_CSCDR3[NFC_PRE_DIV]).
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
61
Memory interfaces
Table 52. NFC specifications
Num
Description
Min.
Max.
Unit
tCLS
NFC_CLE setup time
2TH + TL – 1
—
ns
tCLH
NFC_CLE hold time
TH + TL – 1
—
ns
tCS
NFC_CEn setup time
2TH + TL – 1
—
ns
tCH
NFC_CEn hold time
TH + TL
—
ns
tWP
NFC_WP pulse width
TL – 1
—
ns
tALS
NFC_ALE setup time
2TH + TL
—
ns
tALH
NFC_ALE hold time
TH + TL
—
ns
tDS
Data setup time
TL – 1
—
ns
tDH
Data hold time
TH – 1
—
ns
tWC
Write cycle time
TH + TL – 1
—
ns
tWH
NFC_WE hold time
TH – 1
—
ns
tRR
Ready to NFC_RE low
4TH + 3TL + 90
—
ns
tRP
NFC_RE pulse width
TL + 1
—
ns
tRC
Read cycle time
TL + TH – 1
—
ns
tREH
NFC_RE high hold time
TH – 1
—
ns
tIS
Data input setup time
11
—
ns
NFC_CLE
tCLS
tCLH
NFC_CEn
tCS
tWP
tCH
NFC_WE
tDS
tDH
NFC_IOn
Figure 34. Command latch cycle timing
VF3xxR, VF5xxR, Rev7, 11/2014.
62
Freescale Semiconductor, Inc.
Memory interfaces
NFC_ALE
tALS
tALH
NFC_CEn
tCS
tWP
tCH
NFC_WE
tDS
NFC_IOn
tDH
address
Figure 35. Address latch cycle timing
tCS
tCH
tWC
NFC_CEn
tWP
tWH
tDS
tDH
NFC_WE
NFC_IOn
data
data
data
Figure 36. Write data latch cycle timing
tCH
tRC
NFC_CEn
tRP
tREH
NFC_RE
tIS
NFC_IOn
data
data
data
tRR
NFC_RB
Figure 37. Read data latch cycle timing in non-fast mode
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
63
Memory interfaces
tCH
tRC
NFC_CEn
tRP
tREH
NFC_RE
tIS
NFC_IOn
data
data
data
tRR
NFC_RB
Figure 38. Read data latch cycle timing in fast mode
9.5.3 FlexBus timing specifications
This section provides FlexBus timing parameters. All processor bus timings are
synchronous; input setup/hold and output delay are given in respect to the rising edge of a
reference clock, FB_CLK. The FB_CLK frequency may be the same as the internal
system bus frequency.
The following timing numbers indicate when data is latched or driven onto the external
bus, relative to the FlexBus output clock (FB_CLK). All other timing relationships can be
derived from these values.
All FlexBus signals use pad type pad_fsr. The following timing specifications assume a
pad slew rate setting of 11 and a load of 50 pF3
Table 53. FlexBus timing specifications
Num
Characteristic
Frequency of operation
Min
—
Max
Unit
831
(with
Wait state)
MHz
572 without
Wait state ,
-1
FB1
Clock Period
12
—
ns
FB4
Input setup
10.6
—
ns
FB5
Input hold
0
—
ns
FB2
Output valid
—
6.4
ns
FB3
Output hold
0
—
ns
1. Freq = 1000/(11+ access time of external memory+ trace delay for clk and data)
2. Freq = 1000/(17+access time of external memory)
3.
These timing parameters are specified assuming maximum operating frequency and the fastest pad slew rate setting (11).
VF3xxR, VF5xxR, Rev7, 11/2014.
64
Freescale Semiconductor, Inc.
Memory interfaces
Figure 39. FlexBus read timing
Figure 40. FlexBus write timing
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
65
DDR controller specifications
9.5.4 DDR controller specifications
9.5.4.1
DDR3 Timing Parameters
Figure 41. DDR3 Command and Address Timing Parameters
NOTE
RESET pin has a external weak pull DOWN requirement if
DDR3 memory is NOT required to support content retention in
the device low power modes where core voltage is off but
DRAM voltage is on.
VF3xxR, VF5xxR, Rev7, 11/2014.
66
Freescale Semiconductor, Inc.
DDR controller specifications
NOTE
RESET pin has a external weak pull UP requirement if DDR3
memory is required to support content retention in the device
low power modes where core voltage is off but DRAM voltage
is on.
NOTE
CKE pin has a external weak pull down requirement.
Table 54. DDR3 Timing Parameter
ID
Parameter
Symbol
CK = 400 MHz
Unit
Min
Max
DDR1
CK clock high-level
width
tCH
0.47
0.53
tCK
DDR2
CK clock low-level
width
tCL
0.47
0.53
tCK
DDR4
CS, RAS, CAS,
CKE, WE, ODT
setup time
tIS
440
-
ps
DDR5
CS, RAS, CAS,
CKE, WE, ODT
hold time
tIH
315
-
ps
DDR6
Address output
setup time
tIS
440
-
ps
DDR7
Address output
hold time
tIH
315
-
ps
NOTE
All measurements are in reference to Vref level.
NOTE
Measurements were done using balanced load and 25 ohms
resistor from outputs to VDD_REF.
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
67
DDR controller specifications
9.5.4.2
DDR3 Read Cycle
Figure 42. DDR3 Read Cycle
Table 55. DDR3 Read Cycle
ID
DDR26
Parameter
Symbol
Minimum required DQ valid
window width
-
CK = 400 MHz
Unit
Min
Max
750
-
ps
NOTE
To receive the reported setup and hold values, read calibration
should be performed in order to locate the DQS in the middle of
DQ window.
NOTE
All measurements are in reference to Vref level.
NOTE
Measurements were done using balanced load and 25 ohms
resistor from outputs to VDD_REF
VF3xxR, VF5xxR, Rev7, 11/2014.
68
Freescale Semiconductor, Inc.
DDR controller specifications
9.5.4.3
DDR3 Write cycle
Figure 43. DDR3 Write cycle
Table 56. DDR3 Write cycle
ID
Parameter
Symbol
CK = 400 MHz
Unit
Min
Max
DDR17
DQ and DQM setup time to DQS
(differential strobe)
tDS
240
—
ps
DDR18
DQ and DQM hold time to DQS
(differential strobe)
tDH
215
—
ps
DDR21
DQS latching rising transitions to
associated clock edges
tDQSS
-0.25
+0.25
tCK
DDR22
DQS high level width
tDQSH
0.45
0.55
tCK
DDR22
DQS low level width
tDQSL
0.45
0.55
tCK
NOTE
To receive the reported setup and hold values, write calibration
should be performed in order to locate the DQS in the middle of
DQ window.
NOTE
All measurements are in reference to Vref level.
NOTE
Measurements were done using balanced load and 25 ohms
resistor from outputs to VDD_REF.
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
69
DDR controller specifications
9.5.4.4
LPDDR2 Timing Parameter
Figure 44. LPDDR2 Command and Address timing parameter
NOTE
RESET pin has a external weak pull DOWN requirement if
LPDDR2 memory is NOT required to support content retention
in the device low power modes where core voltage is off but
DRAM voltage is on.
NOTE
RESET pin has a external weak pull UP requirement if
LPDDR2 memory is required to support content retention in the
device low power modes where core voltage is off but DRAM
voltage is on.
NOTE
CKE pin has a external weak pull down requirement.
Table 57. LPDDR2 Timing Parameter
ID
Parameter
Symbol
CK = 400 MHz
Unit
Min
Max
LP1
SDRAM clock high-level width
tCH
0.45
0.55
tCK
LP2
SDRAM clock LOW-level width
tCL
0.45
0.55
tCK
LP3
CS, CKE setup time
tIS
230
-
ps
LP4
CS, CKE hold time
tIH
230
-
ps
LP3
CA setup time
tIS
230
-
ps
LP4
CA hold time
tIH
230
-
ps
NOTE
All measurements are in reference to Vref level.
VF3xxR, VF5xxR, Rev7, 11/2014.
70
Freescale Semiconductor, Inc.
DDR controller specifications
NOTE
Measurements were done using balanced load and 25 ohms
resistor from outputs to VDD_REF.
9.5.4.5
LPDDR2 Read Cycle
Figure 45. LPDDR2 Read cycle
Table 58. LPDDR2 Read Cycle
ID
LP26
Parameter
Symbol
Minimum required DQ valid
window width for LPDDR2
-
CK = 400 MHz
Unit
Min
Max
270
-
ps
NOTE
To receive the reported setup and hold values, read calibration
should be performed in order to locate the DQS in the middle of
DQ window.
NOTE
All measurements are in reference to Vref level.
NOTE
Measurements were done using balanced load and 25 ohms
resistor from outputs to VDD_REF
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
71
DDR controller specifications
9.5.4.6
LPDDR2 Write Cycle
Figure 46. LPDDR3 Write Cycle
Table 59. LPDDR2 Write Cycle
ID
Parameter
Symbol
CK = 400 MHz
Unit
Min
Max
LP17
DQ and DQM setup time to DQS
(differential strobe)
tDS
220
0.55
ps
LP18
DQ and DQM hold time to DQS
(differential strobe)
tDH
220
0.55
ps
LP21
DQS latching rising transitions to
associated clock edges
tDQSS
-0.25
+0.25
tCK
LP22
DQS high level width
tDQSH
0.4
-
tCK
LP23
DQS low level width
tDQSL
0.4
-
tCK
NOTE
To receive the reported setup and hold values, write calibration
should be performed in order to locate the DQS in the middle of
DQ window.
NOTE
All measurements are in reference to Vref level.
NOTE
Measurements were done using balanced load and 25 ohms
resistor from outputs to VDD_REF.
VF3xxR, VF5xxR, Rev7, 11/2014.
72
Freescale Semiconductor, Inc.
Communication interfaces
9.6 Communication interfaces
9.6.1 MediaLB (MLB) DC Characteristics
The section lists the MediaLB 3-pin interface electrical characteristics.
Table 60. MediaLB 3-Pin Interface Electrical DC Specifications
Parameter
Symbol
Test Conditions
Maximum input voltage
—
—
Low level input threshold
VIL
—
Note1
Min
Max
Unit
—
3.6
V
—
0.7
V
1.8
—
V
High level input threshold
VIH
See
Low level output threshold
VOL
IOL = –6 mA
—
0.4
V
High level output threshold
VOH
IOH = –6 mA
2.0
—
V
Input leakage current
IL
0 < Vin < VDD
—
±10
μA
1. Higher VIH thresholds can be used; however, the risks associated with less noise margin in the system must be evaluated
and assumed by the customer.
9.6.2 MediaLB (MLB) Controller AC Timing Electrical Specifications
This section describes the timing electrical information of the MediaLB module.
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
73
Communication interfaces
Figure 47. MediaLB 3-PinTiming
Ground = 0.0 V; Load Capacitance = 40 pF, input transition= 1 ns; MediaLB speed =
256/512 Fs; Fs = 48 kHz; all timing parameters specified from the valid voltage threshold
as listed below; unless otherwise noted.
Table 61. MLB 256/512 Fs Timing Parameters
Parameter
Symbol
Min
Max
MLBCLK operating frequency
fmck
11.264
MLBCLK rise time
tmckr
Refer Table 21
MLBCLK fall time
tmckf
MLBCLK low
time1
25.6
Unit
Comment
MHz
256xFs at 44.0 kHz,
512xFs at 50.0 kHz
ns
VIL to VIH
ns
VIH to VIL
tmckl
30, 14
—
ns
256xFs, 512xFs
MLBCLK high time
tmckh
30, 14
—
ns
256xFs, 512xFs
MLBSIG/MLBDAT receiver input setup to
MLBCLK falling
tdsmcf
3
—
ns
—
MLBSIG/MLBDAT receiver input hold from
MLBCLK low
tdhmcf
2
—
ns
—
MLBSIG/MLBDAT output valid from
MLBCLK low
tmcfdz
0
16
ns
2
Bus output hold from MLBCLK low
tmdzh
2
—
ns
—
1. MLBCLK low/high time includes the pluse width variation.
VF3xxR, VF5xxR, Rev7, 11/2014.
74
Freescale Semiconductor, Inc.
Communication interfaces
2. The MediaLB driver can release the MLBDAT/MLBSIG line as soon as MLBCLK is low; however, the logic state of the final
driven bit on the line must remain on the bus for tmdzh. Therefore, coupling must be minimized while meeting the
maximum load capacitance listed.
Table 62. MLB 1024 Fs Timing Parameters
Parameter
Symbol
Min
Max
MLBCLK Operating Frequency1
fmck
45.056
MLBCLK rise time
fmckr
Refer Table 21
MLBCLK fall time
fmckf
MLBCLK low time
tmckl
6.1
MLBCLK high time
tmckh
MLBSIG/MLBDAT receiver input setup
to MLBCLK falling
51.2
Unit
Comme
nt
MHz
1024xfs
at 44.0
kHz
1024xfs
at 50.0
kHz
ns
VIL to VIH
ns
VIH to VIL
—
ns
2
9.3
—
ns
tdsmcf
3
—
ns
MLBSIG/MLBDAT receiver input hold
from MLBCLK low
tdhmcf
2
—
ns
MLBSIG/MLBDAT output valid from
MLBCLK low
tmcfdz
-
16
ns
Bus Hold from MLBCLK low
tmdzh
2
—
ns
3
1. The controller can shut off MLBCLK to place MediaLB in a low-power state. Depending on the time the clock is shut off, a
runt pulse can occur on MLBCLK.
2. MLBCLK low/high time includes the pluse width variation.
3. The MediaLB driver can release the MLBDAT/MLBSIG line as soon as MLBCLK is low; however, the logic state of the final
driven bit on the line must remain on the bus for tmdzh. Therefore, coupling must be minimized while meeting the
maximum load capacitance listed.
9.6.3 DSPI timing specifications
Table 63. DSPI timing
No.
Symbol
Characteristic
Condition
Min
Max
Unit
1
tSCK
SCK Cycle Time
—
tSYS * 2
—
ns
4
tSDC
SCK Clock Pulse Width
—
40%
60%
tSCK
2
tCSC
CS to SCK Delay
Master
16
—
ns
3
tASC
After SCK Delay
Master
16
—
ns
5
tA
Slave Access Time (SS active Slave
to SOUT driven)
—
15
ns
6
tDI
Slave Disable Time (SS
inactive to SOUT High-Z or
invalid)
Slave
—
10
ns
9
tSUI
Data Setup Time for Inputs
Master
9
—
ns
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
75
Communication interfaces
Table 63. DSPI timing (continued)
No.
10
11
12
Symbol
tHI
Characteristic
Condition
tHO
Max
Slave
4
—
Master
0
—
Slave
2
—
Data Valid (after SCK edge)
for Outputs
Master
—
5
Slave
—
10
Data Hold Time for Outputs
Master
0
—
Slave
0
—
Data Hold Time for Inputs
tDV
Min
2
Unit
ns
ns
ns
3
CSx
1
4
S C K O utput
(C P O L = 0)
4
S C K O utput
(CP OL = 1 )
9
S IN
10
F irst D a ta
D ata
12
SOUT
F irst D ata
La st D ata
11
D ata
L ast D a ta
Figure 48. DSPI classic SPI timing master, CPHA=0
VF3xxR, VF5xxR, Rev7, 11/2014.
76
Freescale Semiconductor, Inc.
Communication interfaces
CSx
S C K O u tp u t
(C P O L = 0 )
10
S C K O u tp u t
(CP OL = 1 )
9
D a ta
F irs t D a ta
S IN
L a s t D a ta
12
SOUT
11
D a ta
F irs t D a ta
L a st D a ta
Figure 49. DSPI classic SPI timing master, CPHA=1
3
2
SS
1
4
S C K In p u t
(C P O L = 0 )
4
S C K In p u t
(C P O L = 1 )
5
SOUT
F irs t D a ta
9
S IN
11
12
D a ta
L a s t D a ta
D a ta
L a s t D a ta
6
10
F irs t D a ta
Figure 50. DSPI classic SPI timing slave, CPHA=0
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
77
Communication interfaces
SS
S C K In p u t
(C P O L = 0 )
S C K In p u t
(C P O L = 1 )
11
5
6
12
SOUT
F irst D a ta
9
S IN
D a ta
L a s t D a ta
D a ta
L a s t D a ta
10
F irst D a ta
Figure 51. DSPI classic SPI timing slave, CPHA=1
9.6.4 I2C timing
Table 64. I2C input timing specifications — SCL and SDA1
No.
Parameter
Min.
Max.
Unit
1
Start condition hold time
2
—
PER_CLK
Cycle2
2
Clock low time
8
—
PER_CLK
Cycle
3
Bus free time between Start and Stop condition
4.7
—
μs
4
Data hold time
0.0
—
μs
5
Clock high time
4
—
PER_CLK
Cycle
6
Data setup time
0.0
—
ns
7
Start condition setup time (for repeated start condition only)
2
—
PER_CLK
Cycle
8
Stop condition setup time
2
—
PER_CLKCyc
le
1. I2C input timing is valid for Automotive and TTL inputs levels, hysteresis enabled, and an input edge rate no slower than 1
ns (10% – 90%).
2. PER_CLK is the IPG Clock which drive the I2C BIU and module clock inputs. Typically this is 83Mhz. See the Clocking
Overview chapter in the device reference manual for more details.
Table 65. I2C output timing specifications — SCL and SDA1234
No.
1
Parameter
Min
Start condition hold
time
6
Max
—
Unit
PER_CLK Cycle5
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
78
Freescale Semiconductor, Inc.
Communication interfaces
Table 65. I2C output timing specifications — SCL and SDA1234 (continued)
No.
Parameter
Min
Max
Unit
2
Clock low time
10
—
PER_CLK Cycle
3
Bus free time between 4.7
Start and Stop condition
—
μs
4
Data hold time
7
—
PER_CLK Cycle
5
Clock high time
10
—
PER_CLK Cycle
6
Data setup time
2
—
PER_CLK Cycle
7
Start condition setup
time (for repeated start
condition only)
20
—
PER_CLK Cycle
8
Stop condition setup
time
10
—
PER_CLK Cycle
1. All output timing is worst case and includes the mismatching of rise and fall times of the output pads.
2. Output parameters are valid for CL = 25 pF, where CL is the external load to the device (lumped). The internal package
capacitance is accounted for, and does not need to be subtracted from the 25 pF value.
3. Timing is guaranteed to same drive capabilities for all signals, mixing of pad drives may reduce operating speedsand may
cause incorrect operation.
4. Programming the IBFD register (I2C bus Frequency Divider) with the maximum frequency results in the minimum output
timings listed. The I2C interface is designed to scale the data transition time, moving it to the middle of the SCL low period.
The actual position is affected by the pre-scale and division values programmed in the IBC field of the IBFD register.
5. PER_CLK is the IPG Clock which drive the I2C BIU and module clock inputs. Typically this is 83Mhz. See the Clocking
Overview chapter in the device reference manual for more details.
Figure 52. I2C input/output timing
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
79
Communication interfaces
9.6.5 SDHC specifications
The following timing specs are defined at the chip I/O pin and must be translated
appropriately to arrive at timing specs/constraints for the physical interface. A load of 50
pF is assumed.
Table 66. SDHC switching specifications
Num
Symbol
Description
Min.
Max.
Unit
Operating voltage
1.71
3.6
V
Card input clock
SD1
fpp
Clock frequency (low speed)
0
400
kHz
fpp
Clock frequency (SD\SDIO full speed\high speed)
0
25\50
MHz
fpp
Clock frequency (MMC full speed\high speed)
0
20\50
MHz
fOD
Clock frequency (identification mode)
0
400
kHz
SD2
tWL
Clock low time
7
—
ns
SD3
tWH
Clock high time
7
—
ns
SD4
tTLH
Clock rise time
—
3
ns
SD5
tTHL
Clock fall time
—
3
ns
SDHC output / card inputs SDHC_CMD, SDHC_DAT (reference to SDHC_CLK)
SD6
tOD
SDHC output delay (output valid)
-5
4
ns
SDHC input / card inputs SDHC_CMD, SDHC_DAT (reference to SDHC_CLK)
SD7
tISU
SDHC input setup time
5
—
ns
SD8
tIH
SDHC input hold time
0
—
ns
SD3
SD2
SD1
SDHC_CLK
SD6
Output SDHC_CMD
Output SDHC_DAT[3:0]
SD7
SD8
Input SDHC_CMD
Input SDHC_DAT[3:0]
Figure 53. SDHC timing
VF3xxR, VF5xxR, Rev7, 11/2014.
80
Freescale Semiconductor, Inc.
Clocks and PLL Specifications
9.6.6 USB PHY specifications
This section describes the USB-OTG PHY and the USB Host port PHY parameters.
The USB PHY meets the electrical compliance requirements defined in the Universal
Serial Bus Revision 2.0 OTG, USB Host with the amendments below (On-The-Go and
Embedded Host Supplement to the USB Revision 2.0 Specification is not applicable to
Host port).
• USB ENGINEERING CHANGE NOTICE
• Title: 5V Short Circuit Withstand Requirement Change
• Applies to: Universal Serial Bus Specification, Revision 2.0
• Errata for USB Revision 2.0 April 27, 2000 as of 12/7/2000
• USB ENGINEERING CHANGE NOTICE
• Title: Pull-up/Pull-down resistors
• Applies to: Universal Serial Bus Specification, Revision 2.0
• USB ENGINEERING CHANGE NOTICE
• Title: Suspend Current Limit Changes
• Applies to: Universal Serial Bus Specification, Revision 2.0
• On-The-Go and Embedded Host Supplement to the USB Revision 2.0 Specification
• Revision 2.0 plus errata and ecn June 4, 2010
• Battery Charging Specification (available from USB-IF)
• Revision 1.2, December 7, 2010
9.7 Clocks and PLL Specifications
9.7.1 24 MHz Oscillator Specifications
The system crystal oscillator consists of a Pierce-type structure running off the digital
supply. A straight forward biased-inverter implementation is used. The crystal must be
rated for a drive level of 250 μW or higher. An ESR (equivalent series resistance) of 80 Ω
or less is recommended to achieve a gain margin of 5.
Table 67. 24MHz external oscillator electrical characteristics
Symbol
Parameter
Condition
Value
Min
Typ
Unit
Max
fosc
Crystal oscillator range
—
—
24
—
MHz
Iosc
Startup current
—
—
<5
—
mA
tuposc
Oscillator startup time
—
—
<5
—
ms
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
81
Clocks and PLL Specifications
Table 67. 24MHz external oscillator electrical characteristics (continued)
Symbol
Parameter
Condition
Value
Min
Typ
Unit
Max
CIN
Input Capacitance
EXTAL and XTAL pins
—
9
—
pF
VIH
XTAL pin input high voltage
—
0.8 x
Vdd1
—
Vdd
+0.3
V
VIL
XTAL pin input low voltage
—
Vss
-0.3
—
0.2 x
Vdd
V
1. VDD =1.1 V ± 10%, TA = -40 to +85 °C, unless otherwise specified.
9.7.2 32 KHz Oscillator Specifications
This block implements an amplifier that when combined with a suitable quartz crystal
and external load capacitors implements a low power oscillator. It also implements a
power mux such that it can be powered from either a ~3 V backup battery or VDDIO
such as the oscillator consumes power from VDDIO when that supply is available and
transitions to the back up battery when VDDIO is lost.
In addition, if the clock monitor determines that the OSC32K is not present, then the
source of the 32 K will automatically switch to the 128kHz internal RC clock divided by
4.
The OSC32k runs from vdd_rtc supply, generated inside OSC32k itself from VDDIO/
VBAT. The target battery is a ~3 V coin cell. Proper choice of coin cell type is necessary
for chosen VDDIO range. Appropriate series resistor (Rs) must be used when connecting
the coin cell. Rs depends on the charge current limit that depends on the chosen coin cell.
For example:
• Average Discharge Voltage is 2.5 V
• Maximum Charge Current is 0.6 mA
For a charge voltage of 3.2 V, Rs = (3.2-2.5)/0.6 m = 1.17 k
Table 68. OSC32K Main Characteristics
Notes
FOSC
This frequency is nominal and determined mainly by the
crystal selected. 32.0 K would work as well.
Current
consumption
The 4 μA is the consumption of the oscillator alone (OSC32k).
Total supply consumption will depend on what the digital
portion of the RTC consumes. The ring oscillator consumes 1
μA when ring oscillator is inactive, 20 μA when the ring
Min
Typ
Max
32.768 KHz
4 μA
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
82
Freescale Semiconductor, Inc.
Clocks and PLL Specifications
Table 68. OSC32K Main Characteristics (continued)
Notes
Min
Typ
Max
oscillator is running. Another 1.5 μA is drawn from vdd_rtc in
the power_detect block. So, the total current is 6.5 μA on
vdd_rtc when the ring oscillator is not running.
Bias resistor
This the integrated bias resistor that sets the amplifier into a
high gain state. Any leakage through the ESD network,
external board leakage, or even a scope probe that is
significant relative to this value will debias the amp. The
debiasing will result in low gain, and will impact the circuit's
ability to start up and maintain oscillations.
14 MΩ
Crystal Properties
Cload
Usually crystals can be purchased tuned for different Cloads.
This Cload value is typically 1/2 of the capacitances realized
on the PCB on either side of the quartz. A higher Cload will
decrease oscillation margin, but increases current oscillating
through the crystal
12.5 pF
ESR
Equivalent series resistance of the crystal. Choosing a crystal
with a higher value will decrease the oscillating margin.
50 kΩ
9.7.3 Fast internal RC oscillator (24 MHz) electrical characteristics
This section describes a fast internal RC oscillator (FIRC). This is used as the default
clock at the power-up of the device.
Table 69. Fast internal oscillator electrical characteristics
Symbol
Condition1
Parameter
Value
Min
Typ
Max
fRCM
RC oscillator high frequency
TA= 25 °C, trimmed
—
24
IRCMRUN
RC oscillator high frequency
current in running mode
TA= 25 °C, trimmed
—
55
μA
IRCMPWD
RC oscillator high frequency
current in power down mode
TA= 25 °C
100
nA
RCMTRIM
RC oscillator precision after
trimming of fRC
TA= 25 °C
RCMVAR
RC oscillator variation in
temperature and supply with
respect to fRC at TA = 55 °C in
high frequency configuration
-1
-5
—
—
Unit
MHz
+1
%
+5
%
1. VDD = 1.2 V , TA = -40 to +85 °C, unless otherwise specified.
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
83
Clocks and PLL Specifications
9.7.4 Slow internal RC oscillator (128 KHz) electrical characteristics
This section describes a slow internal RC oscillator (SIRC). This can be used as the
reference clock for the RTC module.
Table 70. Slow internal RC oscillator electrical characteristics
Symbol
Condition1
Parameter
Value
Min
Typ
Max
—
Unit
fRCL
RC oscillator low frequency
TA= 25 °C, trimmed
—
128
kHz
IRCL
RC oscillator low frequency
current
TA= 25 °C, trimmed
—
3.1
RCLTRIM
RC oscillator precision after
trimming of fRCL
TA= 25 °C
-1
—
+1
%
RCLVAR 3
RC oscillator variation in
temperature and supply with
respect to fRC at TA = 55 °C in
high frequency configuration
High frequency configuration
-5
—
+5
%
μA
1. VDD = 1.2 V , TA = -40 to +85 °C, unless otherwise specified.
9.7.5 PLL1 and PLL2 (528 MHz System PLL) Electrical Parameters
Table 71. PLL1 and PLL2 Electrical Parameters
Parameter
Value
Clock output range
528 MHz PLL output
Reference clock
24 MHz
Lock time
<7500 reference cycles
Period jitter(p2p)
<140ps
Duty Cycle
48.9%~51.7% PLL output
9.7.6 PLL3 and PLL7 (480 MHz USB PLL) Electrical Parameters
Table 72. PLL3 and PLL7 Electrical Parameters
Parameter
Value
Clock output range
480 MHz PLL output
Reference clock
24 MHz
Lock time
<425 reference cycles
Period jitter(p2p)
<140 ps
Duty Cycle
48.9%~51.7% PLL output
VF3xxR, VF5xxR, Rev7, 11/2014.
84
Freescale Semiconductor, Inc.
Clocks and PLL Specifications
9.7.7 PLL5 (Ethernet PLL) Electrical Parameters
Table 73. PLL5 Electrical Parameters
Parameter
Value
Clock output range
500 MHz
Reference clock
24 MHz
Lock time
<7500 reference cycles
Cycle to cycle jitter
(p2p)1
<400ps @ 50 MHz
Duty Cycle
45%~55%
1. Jitter numbers are measured at divided PLL clock because high frequency cannot be brought-out IO pad.
9.7.8 PLL4 (Audio PLL) Electrical Parameters
Table 74. PLL4 Electrical Parameters
Parameter
Value
Clock output range
650 MHz ~1.3 GHz
Reference clock
24 MHz
Lock time
<7500 reference cycles
Long term jitter(RMS)
<42ps @1128MHz
Period
jitter(p2p)1
<115ps@1128MHz
Duty Cycle
43%~57%
1. Jitter numbers are measured at divided PLL clock because high frequency cannot be brought-out on IO pad.
9.7.9 PLL6 (Video PLL) Electrical Parameters
Table 75. PLL6 Electrical Parameters
Parameter
Value
Clock output range
650 MHz ~1.3 GHz
Reference clock
24 MHz
Lock time
<7500 reference cycles
Long term
jitter(RMS)1
<42ps @ 1128 MHz
Period jitter(p2p)
<130ps @960MHz
Duty Cycle
43%~57%
1. Jitter numbers are measured at divided PLL clock because high frequency cannot be brought-out on IO pad & at use case
frequency.
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
85
Debug specifications
9.8 Debug specifications
9.8.1 JTAG electricals
Table 76. JTAG limited voltage range electricals
Symbol
J1
Description
Min.
Max.
Unit
Operating voltage
2.7
3.6
V
TCLK frequency of operation
MHz
• Boundary Scan
-
25
• JTAG and CJTAG
-
25
• Serial Wire Debug
-
25
1/J1
—
ns
• Boundary Scan
20
—
ns
• JTAG and CJTAG
20
—
ns
• Serial Wire Debug
20
—
ns
J2
TCLK cycle period
J3
TCLK clock pulse width
J4
TCLK rise and fall times
J5
Boundary scan input data setup time to TCLK rise
Refer Table 21
J6
ns
8
—
ns
Boundary scan input data hold time after TCLK rise
1.3
—
ns
J7
TCLK low to boundary scan output data valid
—
17
ns
J8
TCLK low to boundary scan output high-Z
—
17
ns
J9
TMS, TDI input data setup time to TCLK rise
8
—
ns
J10
TMS, TDI input data hold time after TCLK rise
1.3
—
ns
J11
TCLK low to TDO data valid
—
17
ns
J12
TCLK low to TDO high-Z
—
17
ns
NOTE
Input transition (1ns), output load (25 pf) and SRE (000), DSE
(111), FSEL(011).
J2
J3
J3
TCLK (input)
J4
J4
Figure 54. Test clock input timing
VF3xxR, VF5xxR, Rev7, 11/2014.
86
Freescale Semiconductor, Inc.
Debug specifications
TCLK
J5
Data inputs
J6
Input data valid
J7
Data outputs
Output data valid
J8
Data outputs
J7
Data outputs
Output data valid
Figure 55. Boundary scan (JTAG) timing
TCLK
J9
TDI/TMS
J10
Input data valid
J11
TDO
Output data valid
J12
TDO
J11
TDO
Output data valid
Figure 56. Test Access Port timing
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
87
Debug specifications
9.8.2 Debug trace timing specifications
Table 77. Debug trace operating behaviors
Symbol
Description
Min.
Max.
Tcyc
Clock period
Twl
Low pulse width
2
—
ns
Twh
High pulse width
2
—
ns
50
Tr
Clock and data rise time
Tf
Clock and data fall time Refer
Unit
MHz
Refer Table 21
ns
ns
tDV
Data output valid
3
—
ns
tHO
Data output hold
1
—
ns
TRACECLK
Tr
Tf
Twh
Twl
Tcyc
Figure 57. TRACE_CLKOUT specifications
trace output clock
trace output data
tHO
tDV
Figure 58. Trace data specifications
VF3xxR, VF5xxR, Rev7, 11/2014.
88
Freescale Semiconductor, Inc.
Thermal attributes
10 Thermal attributes
10.1 Thermal attributes
Board type
Symbol
Description
176LQFP
Unit
Notes
Single-layer (1s)
RθJA
Thermal
50
resistance, junction
to ambient (natural
convection)
°C/W
,
Four-layer (2s2p)
RθJA
Thermal
32
resistance, junction
to ambient (natural
convection)
°C/W
1,
Single-layer (1s)
RθJMA
Thermal
40
resistance, junction
to ambient (200 ft./
min. air speed)
°C/W
1, 2
Four-layer (2s2p)
RθJMA
Thermal
25
resistance, junction
to ambient (200 ft./
min. air speed)
°C/W
1, 2
—
RθJB
Thermal
21
resistance, junction
to board
°C/W
—
RθJCtop
Thermal
12
resistance, junction
to case top
°C/W
—
ΨJT
Thermal
3
characterization
parameter, junction
to package top
(natural
convection)
°C/W
1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site
(board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board
thermal resistance
2. Per JEDEC JESD51-6 with the board (JESD51-7) horizontal.
Board type
Symbol
Description
364 MAPBGA
Unit
Single-layer (1s)
RθJA
Thermal
45
resistance, junction
to ambient (natural
convection)
°C/W
Four-layer (2s2p)
RθJA
Thermal
28
resistance, junction
to ambient (natural
convection)
°C/W
Notes
1
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
89
Dimensions
Board type
Symbol
Description
364 MAPBGA
Unit
Notes
Single-layer (1s)
RθJMA
Thermal
37
resistance, junction
to ambient (200 ft./
min. air speed)
°C/W
1,2
Four-layer (2s2p)
RθJMA
Thermal
24
resistance, junction
to ambient (200 ft./
min. air speed)
°C/W
1,2
—
RθJB
Thermal
17
resistance, junction
to board
°C/W
—
RθJC
Thermal
10
resistance, junction
to case
°C/W
—
ΨJT
Thermal
2
characterization
parameter, junction
to package top
outside center
(natural
convection)
°C/W
1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site
(board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board
thermal resistance.
2. Per JEDEC JESD51-6 with the board horizontal.
11 Dimensions
11.1 Obtaining package dimensions
Package dimensions are provided in package drawing.
To find a package drawing, go to www.freescale.com and perform a keyword search for
the drawing’s document number:
Package
Freescale Document Number
176-pin LQFP
98ASA00452D
364 MAPBGA
98ASA00418D
VF3xxR, VF5xxR, Rev7, 11/2014.
90
Freescale Semiconductor, Inc.
Pinouts
12 Pinouts
12.1 Pinouts
The following table shows the signals available on each pin and the locations of these
pins on the devices supported by this document. The IOMUX Controller Module is
responsible for selecting which ALT functionality is available on each pin.
364 176
MAP LQFP
BGA
Pin Name
Default
ALT0
N/
A
ALT1
Y2
—
ADC0SE8
W2
—
ADC0SE9
ADC0_SE9
W3
—
ADC1SE8
ADC1_SE8
Y3
—
ADC1SE9
ADC1_SE9
W1
34
VREFH_ADC
VREFH_ADC
U3
33
VREFL_ADC
VREFL_ADC
V1
31
VDDA33_
ADC
VDDA33_
ADC
V2
32
VSSA33_
ADC
VSSA33_
ADC
U1
29
DACO0
DACO0
U2
30
DACO1
DACO1
Y4
35
VADCSE0
VADCSE0
U4
37
VADCSE1
VADCSE1
W4
—
VADCSE2
VADCSE2
V5
—
VADCSE3
VADCSE3
V3
40
VDDA33_
AFE
VDDA33_
AFE
V4
39
VSSA33_AFE
VSSA33_AFE
T5
36
VDD12_AFE
VDD12_AFE
R5
38
VSS12_AFE
VSS12_AFE
U5
41
VADC_AFE_
BANDGAP
VADC_AFE_
BANDGAP
Y13
73
EXTAL
EXTAL
W13
72
XTAL
XTAL
Y12
70
EXTAL32
EXTAL32
W12
71
XTAL32
XTAL32
T4
28
RESETB/
RESETB/
RESET_OUT RESET_OUT
RESETB/
RESET_OUT
N5
19
PTA6
ALT2
ALT3
ALT4
ALT5
ALT6
ALT7
EzPort
ADC0_SE8
PTA6
RMII_
CLKOUT
RMII_CLKIN/
MII0_TXCLK
DCU1_
TCON11
DCU1_R2
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
91
Pinouts
364 176
MAP LQFP
BGA
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
ALT7
T3
27
TEST
TEST
T1
23
Ext_POR
TEST2
V12
69
DECAP_
V11_LDO_
OUT
DECAP_
V11_LDO_
OUT
T11
65
DECAP_
V25_LDO_
OUT
DECAP_
V25_LDO_
OUT
T2
26
BCTRL
BCTRL
P5
24
VDDREG
VDDREG
T12
68
VDD33_
LDOIN
VDD33_
LDOIN
V11
67
VSS
VSS
U11
66
VSS_KEL0
VSS_KEL0
W14
—
LVDS0P
LVDS0P
Y14
—
LVDS0N
LVDS0N
K4
3
JTCLK/
SWCLK
JTCLK/
SWCLK
PTA8
JTCLK/
SWCLK
K2
4
JTDI
JTDI
PTA9
JTDI
RMII_
CLKOUT
K1
5
JTDO
JTDO/
TRACESWO
PTA10
JTDO
EXT_AUDIO_
MCLK
L1
6
JTMS/
SWDIO
JTMS/
SWDIO
PTA11
JTMS/
SWDIO
L3
7
PTA12
PTA12
TRACECK
EXT_AUDIO_
MCLK
Y5
43
PTA16
PTA16
TRACED0
USB0_
VBUS_EN
ADC1_SE0
LCD29
SAI2_TX_
BCLK
VIU_DATA14 I2C0_SDA
Y6
44
PTA17
PTA17
TRACED1
USB0_
VBUS_OC
ADC1_SE1
LCD30
USB0_SOF_
PULSE
VIU_DATA15 I2C1_SCL
V6
46
PTA18
PTA18
TRACED2
ADC0_SE0
FTM1_QD_
PHA
LCD31
SAI2_TX_
DATA
VIU_DATA16 I2C1_SDA
U6
47
PTA19
PTA19
TRACED3
ADC0_SE1
FTM1_QD_
PHB
LCD32
SAI2_TX_
SYNC
VIU_DATA17 QSPI1_A_
SCK
B18
143
PTA20
PTA20
TRACED4
D18
145
PTA21
PTA21/
MII0_RXCLK
TRACED5
E17
147
PTA22
PTA22
TRACED6
DCU0_R0
EzPort
MLBCLK
RMII_CLKIN/ DCU0_R1
MII0_TXCLK
WDOG_b
DCU0_G0
ENET_TS_
CLKIN
DCU0_G1
MLBSIGNAL
MLBDATA
VIU_DATA13 I2C0_SCL
LCD33
SCI3_TX
DCU1_
HSYNC/
DCU1_
TCON1
SAI2_RX_
BCLK
SCI3_RX
DCU1_
VSYNC/
DCU1_
TCON2
SAI2_RX_
DATA
I2C2_SCL
DCU1_TAG/
DCU1_
TCON0
VF3xxR, VF5xxR, Rev7, 11/2014.
92
Freescale Semiconductor, Inc.
Pinouts
364 176
MAP LQFP
BGA
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
SAI2_RX_
SYNC
I2C2_SDA
ALT7
C17
148
PTA23
PTA23
TRACED7
R16
—
PTA24
PTA24
TRACED8
USB1_
VBUS_EN
SDHC1_CLK DCU1_
TCON4
R17
—
PTA25
PTA25
TRACED9
USB1_
VBUS_OC
SDHC1_CMD DCU1_
TCON5
R19
—
PTA26
PTA26
TRACED10
SAI3_TX_
BCLK
SDHC1_
DAT0
DCU1_
TCON6
R20
—
PTA27
PTA27
TRACED11
SAI3_RX_
BCLK
SDHC1_
DAT1
DCU1_
TCON7
P20
—
PTA28
PTA28
TRACED12
SAI3_RX_
DATA
ENET1_
1588_TMR0
SCI4_TX
SDHC1_
DAT2
DCU1_
TCON8
P18
—
PTA29
PTA29
TRACED13
SAI3_TX_
DATA
ENET1_
1588_TMR1
SCI4_RX
SDHC1_
DAT3
DCU1_
TCON9
P17
—
PTA30
PTA30
TRACED14
SAI3_RX_
SYNC
ENET1_
1588_TMR2
SCI4_RTS
I2C3_SCL
SCI3_TX
P16
—
PTA31
PTA31
TRACED15
SAI3_TX_
SYNC
ENET1_
1588_TMR3
SCI4_CTS
I2C3_SDA
SCI3_RX
T6
49
PTB0
PTB0
FTM0_CH0
ADC0_SE2
TRACECTL
LCD34
SAI2_RX_
BCLK
VIU_DATA18 QSPI1_A_
CS0
T7
50
PTB1
RCON30
PTB1
FTM0_CH1
ADC0_SE3
RCON30
LCD35
SAI2_RX_
DATA
VIU_DATA19 QSPI1_A_
DATA3
V7
51
PTB2
RCON31
PTB2
FTM0_CH2
ADC1_SE2
RCON31
LCD36
SAI2_RX_
SYNC
VIU_DATA20 QSPI1_A_
DATA2
W7
53
PTB3
PTB3
FTM0_CH3
ADC1_SE3
EXTRIG
LCD37
Y7
54
PTB4
PTB4
FTM0_CH4
SCI1_TX
ADC0_SE4
LCD38
VIU_FID
VIU_DATA22 QSPI1_A_
DATA0
Y8
55
PTB5
PTB5
FTM0_CH5
SCI1_RX
ADC1_SE4
LCD39
VIU_DE
VIU_DATA23 QSPI1_A_
DQS
W8
56
PTB6
PTB6
FTM0_CH6
SCI1_RTS
QSPI0_A_
CS1
LCD40
FB_CLKOUT VIU_HSYNC
SCI2_TX
D13
166
PTB7
PTB7
FTM0_CH7
SCI1_CTS
QSPI0_B_
CS1
LCD41
VIU_VSYNC
SCI2_RX
J16
121
PTB8
PTB8
FTM1CH0
FTM1_QD_
PHA
J19
123
PTB9
PTB9
FTM1CH1
FTM1_QD_
PHB
B15
159
PTB10
PTB10
SCI0_TX
DCU0_
TCON4
VIU_DE
CKO1
ENET_TS_
CLKIN
D14
164
PTB11
PTB11
SCI0_RX
DCU0_
TCON5
SNVS_
ALARM_
OUT_B
CKO2
ENET0_
1588_TMR0
E13
165
PTB12
PTB12
SCI0_RTS
SPI0_PCS5
DCU0_
TCON6
FB_AD1
NMI
ENET0_
1588_TMR1
D15
156
PTB13
PTB13
SCI0_CTS
SPI0_PCS4
DCU0_
TCON7
FB_AD0
TRACECTL
NMI
EzPort
DCU1_DE/
DCU1_
TCON3
VIU_DATA21 QSPI1_A_
DATA1
VIU_DE
DCU1_R6
DCU1_R7
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
93
Pinouts
364 176
MAP LQFP
BGA
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
ALT7
B14
162
PTB14
PTB14
CAN0_RX
I2C0_SCL
DCU0_
TCON8
DCU1_PCLK
A14
161
PTB15
PTB15
CAN0_TX
I2C0_SDA
DCU0_
TCON9
VIU_PIX_
CLK
C14
163
PTB16
PTB16
CAN1_RX
I2C1_SCL
DCU0_
TCON10
A15
160
PTB17
PTB17
CAN1_TX
I2C1_SDA
DCU0_
TCON11
B12
171
PTB18
PTB18
SPI0_PCS1
EXT_AUDIO_
MCLK
C13
167
PTB19
PTB19
SPI0_PCS0
A13
169
PTB20
PTB20
SPI0_SIN
LCD42
VIU_DATA11 CCM_OBS2
E12
173
PTB21
PTB21
SPI0_SOUT
LCD43
VIU_DATA12 DCU1_PCLK
D12
172
PTB22
PTB22
SPI0_SCK
V10
61
USB0_GND
USB0_GND
T10
63
USB0_DP
USB0_DP
T9
62
USB0_DM
USB0_DM
W11
60
USB0_VBUS
USB0_VBUS
Y10
59
USB_DCAP
USB_DCAP
Y11
64
USB0_
VBUS_
DETECT
USB0_
VBUS_
DETECT
Y9
—
USB1_GND
USB1_GND
W9
—
USB1_DP
USB1_DP
V9
—
USB1_DM
USB1_DM
W10
—
USB1_VBUS
USB1_VBUS
U9
—
USB1_
VBUS_
DETECT
USB1_
VBUS_
DETECT
L4
8
PTC0
PTC0
RMII0_MDC/
MII0_MDC
FTM1CH0
SPI0_PCS3
ESAI_SCKT
SDHC0_CLK VIU_DATA0
RCON18
L5
9
PTC1
PTC1
RMII0_MDIO/ FTM1CH1
MII0_MDC
SPI0_PCS2
ESAI_FST
SDHC0_CMD VIU_DATA1
RCON19
M5
11
PTC2
PTC2
RMII0_CRS_ SCI1_TX
DV
ESAI_SDO0
SDHC0_
DAT0
VIU_DATA2
RCON20
M3
12
PTC3
PTC3
RMII0_RXD1/ SCI1_RX
MII0_RXD[1]
ESAI_SDO1
SDHC0_
DAT1
VIU_DATA3
DCU0_R0
L2
14
PTC4
PTC4
RMII0_RXD0/ SCI1_RTS
MII0_RXD[0]
SPI1_PCS1
ESAI_SDO2/
ESAI_SDI3
SDHC0_
DAT2
VIU_DATA4
DCU0_R1
M1
15
PTC5
PTC5
RMII0_RXER/ SCI1_CTS
MII0_RXER
SPI1_PCS0
ESAI_SDO3/
ESAI_SDI2
SDHC0_
DAT3
VIU_DATA5
DCU0_G0
N1
16
PTC6
PTC6
RMII0_TXD1/
MII0_TXD[1]
SPI1_SIN
ESAI_SDO5/
ESAI_SDI0
SDHC0_WP
VIU_DATA6
DCU0_G1
N2
17
PTC7
PTC7
RMII0_TXD0/
MII0_TXD[0]
SPI1_SOUT
ESAI_SDO4/
ESAI_SDI1
VIU_DATA7
DCU0_B0
VIU_DATA9
EzPort
CCM_OBS0
VIU_DATA10 CCM_OBS1
VIU_FID
VF3xxR, VF5xxR, Rev7, 11/2014.
94
Freescale Semiconductor, Inc.
Pinouts
364 176
MAP LQFP
BGA
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
N4
18
PTC8
PTC8
RMII0_TXEN/
MII0_TXEN
SPI1_SCK
VIU_DATA8
T15
—
PTC9
PTC9
RMII1_MDC
ESAI_SCKT
MLBCLK
U15
—
PTC10
PTC10
RMII1_MDIO
ESAI_FST
MLBSIGNAL
P4
—
PTC11
PTC11
RMII1_CRS_
DV
ESAI_SDO0
MLBDATA
P3
—
PTC12
PTC12
RMII1_RXD1
ESAI_SDO1
SAI2_TX_
BCLK
P1
—
PTC13
PTC13
RMII1_RXD0
ESAI_SDO2/
ESAI_SDI3
SAI2_RX_
BCLK
R1
—
PTC14
PTC14
RMII1_RXER
ESAI_SDO3/
ESAI_SDI2
SCI5_TX
SAI2_RX_
DATA
ADC0_SE6
P2
—
PTC15
PTC15
RMII1_TXD1
ESAI_SDO5/
ESAI_SDI0
SCI5_RX
SAI2_TX_
DATA
ADC0_SE7
R3
—
PTC16
PTC16
RMII1_TXD0
ESAI_SDO4/
ESAI_SDI1
SCI5_RTS
SAI2_RX_
SYNC
ADC1_SE6
R4
—
PTC17
PTC17
RMII1_TXEN
ADC1_SE7
SCI5_CTS
SAI2_TX_
SYNC
USB1_SOF_
PULSE
B10
—
DDR_A[15]
DDR_A15
D9
—
DDR_A[14]
DDR_A14
A10
—
DDR_A[13]
DDR_A13
C10
—
DDR_A[12]
DDR_A12
D10
—
DDR_A[11]
DDR_A11
D7
—
DDR_A[10]
DDR_A10
B9
—
DDR_A[9]
DDR_A9
A11
—
DDR_A[8]
DDR_A8
A7
—
DDR_A[7]
DDR_A7
A9
—
DDR_A[6]
DDR_A6
B6
—
DDR_A[5]
DDR_A5
A6
—
DDR_A[4]
DDR_A4
B7
—
DDR_A[3]
DDR_A3
A8
—
DDR_A[2]
DDR_A2
C11
—
DDR_A[1]
DDR_A1
C7
—
DDR_A[0]
DDR_A0
D8
—
DDR_BA[2]
DDR_BA2
C9
—
DDR_BA[1]
DDR_BA1
C8
—
DDR_BA[0]
DDR_BA0
B4
—
DDR_CAS_b
DDR_CAS_b
A5
—
DDR_CKE[0]
DDR_CKE0
A2
—
DDR_CLK[0]
DDR_CLK0
B2
—
DDR_CLK_
b[0]
DDR_CLK_
b0
ALT7
EzPort
DCU0_B1
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
95
Pinouts
364 176
MAP LQFP
BGA
Pin Name
Default
ALT0
ALT1
C5
—
DDR_CS_
b[0]
DDR_CS_b0
D2
—
DDR_D[15]
DDR_D15
H2
—
DDR_D[14]
DDR_D14
C1
—
DDR_D[13]
DDR_D13
G1
—
DDR_D[12]
DDR_D12
E2
—
DDR_D[11]
DDR_D11
H1
—
DDR_D[10]
DDR_D10
D1
—
DDR_D[9]
DDR_D9
J1
—
DDR_D[8]
DDR_D8
G3
—
DDR_D[7]
DDR_D7
C3
—
DDR_D[6]
DDR_D6
J3
—
DDR_D[5]
DDR_D5
F3
—
DDR_D[4]
DDR_D4
G4
—
DDR_D[3]
DDR_D3
D4
—
DDR_D[2]
DDR_D2
H3
—
DDR_D[1]
DDR_D1
F4
—
DDR_D[0]
DDR_D0
G2
—
DDR_DQM[1]
DDR_DQM1
J4
—
DDR_DQM[0]
DDR_DQM0
E1
—
DDR_DQS[1]
DDR_DQS1
D3
—
DDR_DQS[0]
DDR_DQS0
F1
—
DDR_DQS_
b[1]
DDR_DQS_
b1
E3
—
DDR_DQS_
b[0]
DDR_DQS_
b0
A4
—
DDR_RAS_b
DDR_RAS_b
C6
—
DDR_WE_b
DDR_WE_b
C4
—
DDR_ODT[0]
DDR_ODT0
B1
—
DDR_ODT[1]
DDR_ODT1
G5
—
DDR_VREF
DDR_VREF
A3
—
DDR_ZQ
DDR_ZQ
ALT2
ALT3
ALT4
ALT5
D6
—
DDR_RESET
J20
—
PTD31
PTD31
FB_AD31
NF_IO15
FTM3_CH0
SPI2_PCS1
H20
—
PTD30
PTD30
FB_AD30
NF_IO14
FTM3_CH1
SPI2_PCS0
H18
—
PTD29
PTD29
FB_AD29
NF_IO13
FTM3_CH2
SPI2_SIN
H17
—
PTD28
PTD28
FB_AD28
NF_IO12
I2C2_SCL
FTM3_CH3
SPI2_SOUT
H16
—
PTD27
PTD27
FB_AD27
NF_IO11
I2C2_SDA
FTM3_CH4
SPI2_SCK
G16
—
PTD26
PTD26
FB_AD26
NF_IO10
FTM3_CH5
SDHC1_WP
G18
—
PTD25
PTD25
FB_AD25
NF_IO9
FTM3_CH6
G19
—
PTD24
PTD24
FB_AD24
NF_IO8
FTM3_CH7
ALT6
ALT7
EzPort
DDR_RESET
VF3xxR, VF5xxR, Rev7, 11/2014.
96
Freescale Semiconductor, Inc.
Pinouts
364 176
MAP LQFP
BGA
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
ALT7
G20
124
PTD23
PTD23/
MII0_
RXDATA[3]
FB_AD23
NF_IO7
FTM2CH0
ENET0_
1588_TMR0
SDHC0_
DAT4
SCI2_TX
DCU1_R3
F20
126
PTD22
PTD22/
MII0_
RXDATA[2]
FB_AD22
NF_IO6
FTM2CH1
ENET0_
1588_TMR1
SDHC0_
DAT5
SCI2_RX
DCU1_R4
F19
128
PTD21
PTD21/
MII0_CRS
FB_AD21
NF_IO5
ENET0_
1588_TMR2
SDHC0_
DAT6
SCI2_RTS
DCU1_R5
F17
129
PTD20
PTD20/
MII0_COL
FB_AD20
NF_IO4
ENET0_
1588_TMR3
SDHC0_
DAT7
SCI2_CTS
DCU1_R0
F16
130
PTD19
PTD19
FB_AD19
NF_IO3
ESAI_SCKR
I2C0_SCL
FTM2_QD_
PHA
MII0_
TXDATA[3]
DCU1_R1
E18
131
PTD18
PTD18
FB_AD18
NF_IO2
ESAI_FSR
I2C0_SDA
FTM2_QD_
PHB
MII0_
TXDATA[2]
DCU1_G0
E20
132
PTD17
PTD17
FB_AD17
NF_IO1
ESAI_HCKR
I2C1_SCL
MII0_TXERR DCU1_G1
D20
133
PTD16
PTD16
FB_AD16
NF_IO0
ESAI_HCKT
I2C1_SDA
DCU1_G2
Y17
86
PTD0
PTD0
QSPI0_A_
SCK
SCI2_TX
FB_AD15
SPDIF_
EXTCLK
Y18
87
PTD1
PTD1
QSPI0_A_
CS0
SCI2_RX
FB_AD14
SPDIF_IN1
V18
88
PTD2
PTD2
QSPI0_A_
DATA3
SCI2_RTS
SPI1_PCS3
FB_AD13
SPDIF_OUT1
Y19
89
PTD3
PTD3
QSPI0_A_
DATA2
SCI2_CTS
SPI1_PCS2
FB_AD12
SPDIF_
PLOCK
W19
90
PTD4
PTD4
QSPI0_A_
DATA1
SPI1_PCS1
FB_AD11
SPDIF_
SRCLK
W20
91
PTD5
PTD5
QSPI0_A_
DATA0
SPI1_PCS0
FB_AD10
V20
92
PTD6
PTD6
QSPI0_A_
DQS
SPI1_SIN
FB_AD9
V19
93
PTD7
PTD7
QSPI0_B_
SCK
SPI1_SOUT
FB_AD8
U17
94
PTD8
PTD8
QSPI0_B_
CS0
FB_CLKOUT SPI1_SCK
FB_AD7
U18
97
PTD9
PTD9
QSPI0_B_
DATA3
SPI3_PCS1
FB_AD6
U20
98
PTD10
PTD10
QSPI0_B_
DATA2
SPI3_PCS0
FB_AD5
T20
99
PTD11
PTD11
QSPI0_B_
DATA1
SPI3_SIN
FB_AD4
T19
100
PTD12
PTD12
QSPI0_B_
DATA0
SPI3_SOUT
FB_AD3
T18
101
PTD13
PTD13
QSPI0_B_
DQS
SPI3_SCK
FB_AD2
A19
141
PTB23
PTB23
SAI0_TX_
BCLK
SCI1_TX
FB_MUXED_ FB_TS_b
ALE
SAI1_TX_
SYNC
EzPort
DCU1_B0
DCU1_B1
SCI3_RTS
DCU1_G3
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
97
Pinouts
364 176
MAP LQFP
BGA
Pin Name
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
ALT6
ALT7
SCI3_CTS
DCU1_G4
A18
142
PTB24
PTB24
SAI0_RX_
BCLK
SCI1_RX
FB_MUXED_ NF_WE_b
TSIZ0
B17
149
PTB25
PTB25
SAI0_RX_
DATA
SCI1_RTS
FB_CS1_b
NF_CE0_b
DCU1_G5
A17
150
PTB26
RCON21
PTB26
SAI0_TX_
DATA
SCI1_CTS
RCON21
FB_CS0_b
NF_CE1_b
DCU1_G6
U8
57
PTB27
RCON22
PTB27
SAI0_RX_
SYNC
RCON22
FB_OE_b
FB_MUXED_ NF_RE_b
TBST_b
DCU1_G7
A16
151
PTB28
RCON23
PTB28
SAI0_TX_
SYNC
RCON23
FB_RW_b
D16
153
PTC26
RCON24
PTC26
SAI1_TX_
BCLK
SPI0_PCS5
RCON24
FB_TA_b
NF_RB_b
E16
154
PTC27
RCON25
PTC27
SAI1_RX_
BCLK
SPI0_PCS4
RCON25
FB_BE3_b
FB_CS3_b
NF_ALE
DCU1_B2
E15
155
PTC28
RCON26
PTC28
SAI1_RX_
DATA
SPI0_PCS3
RCON26
FB_BE2_b
FB_CS2_b
NF_CLE
DCU1_B3
C16
152
PTC29
RCON27
PTC29
SAI1_TX_
DATA
SPI0_PCS2
RCON27
FB_BE1_b
FB_MUXED_
TSIZ1
T8
58
PTC30
RCON28
PTC30
SAI1_RX_
SYNC
SPI1_PCS2
RCON28
FB_MUXED_ FB_TSIZ0
BE0_b
W5
42
PTC31
RCON29
PTC31
SAI1_TX_
SYNC
N16
103
PTE0
BOOTMOD1
PTE0
DCU0_
HSYNC/
DCU0_
TCON1
BOOTMOD1
LCD0
N18
104
PTE1
BOOTMOD0
PTE1
DCU0_
VSYNC/
DCU0_
TCON2
BOOTMOD0
LCD1
N19
105
PTE2
PTE2
DCU0_PCLK
LCD2
Y15
77
PTE3
PTE3
DCU0_TAG/
DCU0_
TCON0
LCD3
N20
106
PTE4
PTE4
DCU0_DE/
DCU0_
TCON3
LCD4
T16
80
PTE5
PTE5
DCU0_R0
LCD5
W16
81
PTE6
PTE6
DCU0_R1
M20
109
PTE7
RCON0
PTE7
DCU0_R2
RCON0
LCD7
M19
110
PTE8
RCON1
PTE8
DCU0_R3
RCON1
LCD8
M17
111
PTE9
RCON2
PTE9
DCU0_R4
RCON2
LCD9
M16
112
PTE10
RCON3
PTE10
DCU0_R5
RCON3
LCD10
L16
113
PTE11
RCON4
PTE11
DCU0_R6
RCON4
LCD11
L17
114
PTE12
RCON5
PTE12
DCU0_R7
RCON5
LCD12
Y16
78
PTE13
PTE13
DCU0_G0
RCON29
EzPort
DCU1_B6
DCU1_B7
DCU1_B4
ADC0_SE5
DCU1_B5
ADC1_SE5
DCU1_B6
LCD6
SPI1_PCS3
LPT_ALT0
LCD13
VF3xxR, VF5xxR, Rev7, 11/2014.
98
Freescale Semiconductor, Inc.
Pinouts
364 176
MAP LQFP
BGA
Pin Name
W15
76
PTE14
L18
115
PTE15
L20
116
K20
K19
Default
ALT0
ALT1
ALT2
ALT3
ALT4
ALT5
PTE14
DCU0_G1
RCON6
PTE15
DCU0_G2
RCON6
LCD15
PTE16
RCON7
PTE16
DCU0_G3
RCON7
LCD16
117
PTE17
RCON8
PTE17
DCU0_G4
RCON8
LCD17
118
PTE18
RCON9
PTE18
DCU0_G5
RCON9
LCD18
K18
119
PTE19
RCON10
PTE19
DCU0_G6
RCON10
LCD19
I2C0_SCL
A12
170
PTE20
RCON11
PTE20
DCU0_G7
RCON11
LCD20
I2C0_SDA
V16
79
PTE21
PTE21
DCU0_B0
LCD21
W17
84
PTE22
PTE22
DCU0_B1
LCD22
J17
122
PTE23
RCON12
PTE23
DCU0_B2
RCON12
LCD23
D19
134
PTE24
RCON13
PTE24
DCU0_B3
RCON13
LCD24
C19
135
PTE25
RCON14
PTE25
DCU0_B4
RCON14
LCD25
C20
137
PTE26
RCON15
PTE26
DCU0_B5
RCON15
LCD26
B20
138
PTE27
RCON16
PTE27
DCU0_B6
RCON16
LCD27
I2C1_SCL
K16
120
PTE28
RCON17
PTE28
DCU0_B7
RCON17
LCD28
I2C1_SDA
V15
75
PTA7
PTA7
VIU_PIX_
CLK
T14
—
EXT_
TAMPER0
EXT_
TAMPER0
U14
—
EXT_
TAMPER1
EXT_
TAMPER1
T13
—
EXT_
TAMPER2/
EXT_WM0_
TAMPER_IN
EXT_
TAMPER2/
EXT_WM0_
TAMPER_IN
U13
—
EXT_
TAMPER3/
EXT_WM0_
TAMPER_
OUT
EXT_
TAMPER3/
EXT_WM0_
TAMPER_
OUT
U12
—
EXT_
TAMPER4/
EXT_WM1_
TAMPER_IN
EXT_
TAMPER4/
EXT_WM1_
TAMPER_IN
U10
—
EXT_
TAMPER5/
EXT_WM1_
TAMPER_
OUT
EXT_
TAMPER5/
EXT_WM1_
TAMPER_
OUT
G7
2
VDD
VDD
J7
22
VDD
VDD
L7
48
VDD
VDD
H8
—
VDD
VDD
K8
85
VDD
VDD
M8
102
VDD
VDD
ALT6
ALT7
EzPort
LCD14
EWM_in
EWM_out
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
99
Pinouts
364 176
MAP LQFP
BGA
Pin Name
Default
ALT0
ALT1
P8
125
VDD
VDD
G9
136
VDD
VDD
N9
174
VDD
VDD
H10
—
VDD
VDD
P10
—
VDD
VDD
G11
—
VDD
VDD
N11
—
VDD
VDD
H12
—
VDD
VDD
P12
—
VDD
VDD
G13
—
VDD
VDD
J13
—
VDD
VDD
L13
—
VDD
VDD
N13
—
VDD
VDD
H14
—
VDD
VDD
K14
—
VDD
VDD
M14
—
VDD
VDD
P14
—
VDD
VDD
A1
1
VSS
VSS
A20
13
VSS
VSS
B3
20
VSS
VSS
B5
25
VSS
VSS
B8
45
VSS
VSS
B11
—
VSS
VSS
B13
—
VSS
VSS
B16
—
VSS
VSS
B19
—
VSS
VSS
C2
—
VSS
VSS
D17
—
VSS
VSS
E5
—
VSS
VSS
E8
—
VSS
VSS
E11
—
VSS
VSS
E14
—
VSS
VSS
E19
—
VSS
VSS
F2
—
VSS
VSS
G17
—
VSS
VSS
H4
—
VSS
VSS
J2
—
VSS
VSS
J18
—
VSS
VSS
M2
—
VSS
VSS
M4
—
VSS
VSS
ALT2
ALT3
ALT4
ALT5
ALT6
ALT7
EzPort
VF3xxR, VF5xxR, Rev7, 11/2014.
100
Freescale Semiconductor, Inc.
Pinouts
364 176
MAP LQFP
BGA
Pin Name
Default
ALT0
ALT1
M18
—
VSS
VSS
R2
—
VSS
VSS
R18
—
VSS
VSS
U7
—
VSS
VSS
U19
—
VSS
VSS
V13
—
VSS
VSS
W6
—
VSS
VSS
V17
—
VSS
VSS
Y1
—
VSS
VSS
Y20
—
VSS
VSS
H19
—
VSS
VSS
L19
—
VSS
VSS
P19
—
VSS
VSS
J5
—
SDRAMC_
VDD2P5
SDRAMC_
VDD2P5
E6
—
SDRAMC_
VDD2P5
SDRAMC_
VDD2P5
E10
—
SDRAMC_
VDD2P5
SDRAMC_
VDD2P5
E4
—
SDRAMC_
VDD1P5
SDRAMC_
VDD1P5
D5
—
SDRAMC_
VDD1P5
SDRAMC_
VDD1P5
F5
—
SDRAMC_
VDD1P5
SDRAMC_
VDD1P5
H5
—
SDRAMC_
VDD1P5
SDRAMC_
VDD1P5
K5
—
SDRAMC_
VDD1P5
SDRAMC_
VDD1P5
E7
—
SDRAMC_
VDD1P5
SDRAMC_
VDD1P5
E9
—
SDRAMC_
VDD1P5
SDRAMC_
VDD1P5
D11
—
SDRAMC_
VDD1P5
SDRAMC_
VDD1P5
K3
10
VDD33
VDD33
N3
21
VDD33
VDD33
V8
52
VDD33
VDD33
C12
—
VDD33
VDD33
C15
83
VDD33
VDD33
U16
95
VDD33
VDD33
K17
108
VDD33
VDD33
N17
127
VDD33
VDD33
ALT2
ALT3
ALT4
ALT5
ALT6
ALT7
EzPort
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
101
Pinouts
364 176
MAP LQFP
BGA
Pin Name
Default
ALT0
ALT1
T17
140
VDD33
VDD33
C18
146
VDD33
VDD33
F18
158
VDD33
VDD33
W18
168
VDD33
VDD33
H7
—
VSS
VSS
K7
74
VSS
VSS
M7
82
VSS
VSS
P7
96
VSS
VSS
G8
107
VSS
VSS
J8
—
VSS
VSS
L8
139
VSS
VSS
N8
—
VSS
VSS
H9
157
VSS
VSS
J9
175
VSS
VSS
K9
176
VSS
VSS
L9
—
VSS
VSS
M9
—
VSS
VSS
P9
—
VSS
VSS
G10
—
VSS
VSS
J10
—
VSS
VSS
K10
—
VSS
VSS
L10
—
VSS
VSS
M10
—
VSS
VSS
N10
—
VSS
VSS
H11
—
VSS
VSS
J11
—
VSS
VSS
K11
—
VSS
VSS
L11
—
VSS
VSS
M11
—
VSS
VSS
P11
—
VSS
VSS
G12
—
VSS
VSS
J12
—
VSS
VSS
K12
—
VSS
VSS
L12
—
VSS
VSS
M12
—
VSS
VSS
N12
—
VSS
VSS
H13
—
VSS
VSS
K13
—
VSS
VSS
M13
—
VSS
VSS
P13
—
VSS
VSS
ALT2
ALT3
ALT4
ALT5
ALT6
ALT7
EzPort
VF3xxR, VF5xxR, Rev7, 11/2014.
102
Freescale Semiconductor, Inc.
Pinouts
364 176
MAP LQFP
BGA
Pin Name
Default
ALT0
ALT1
G14
—
VSS
VSS
J14
—
VSS
VSS
L14
—
VSS
VSS
N14
—
VSS
VSS
N7
—
FA_VDD
FA_VDD
V14
—
VBAT
VBAT
—
FLG VSS
ALT2
ALT3
ALT4
ALT5
ALT6
ALT7
EzPort
VSS
12.2 Pinout diagrams
NOTE
The 176 LQFP parts are not pin compatible between the F and
R series families devices.
NOTE
If tamper detection is not required, the tamper pins must be tied
to ground.
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
103
VSS
PTE26
VDD
PTE25
PTE24
PTD16
137
136
135
134
133
VDD33
140
PTE27
PTB23
141
138
PTB24
142
139
VSS
PTA20
PTA21
145
143
VDD33
146
144
PTA23
PTB25
149
PTA22
PTB26
150
147
PTB28
151
148
PTC26
PTC29
PTC27
154
152
PTC28
155
153
VSS
PTB13
157
156
PTB10
VDD33
159
158
PTB15
PTB17
160
PTB14
162
161
PTB11
PTB16
164
163
PTB7
PTB12
166
165
VDD33
PTB19
168
167
PTE20
PTB20
170
169
PTB22
PTB21
PTB18
VDD
173
171
VSS
174
172
VSS
176
175
Pinouts
VSS
1
132
PTD17
VDD
2
131
PTD18
JTCLK/SWCLK
3
130
PTD19
JTDI
4
129
PTD20
PTD21
JTDO
5
128
JTMS/SWDIO
6
127
VDD33
PTA12
7
126
PTD22
PTC0
8
125
VDD
PTC1
9
124
PTD23
VDD33
10
123
PTB9
PTC2
11
122
PTE23
PTC3
12
121
PTB8
VSS
13
120
PTE28
PTC4
14
119
PTE19
PTC5
15
118
PTE18
PTC6
16
117
PTE17
PTC7
17
116
PTE16
PTC8
18
115
PTE15
PTA6
19
114
PTE12
VSS
20
113
PTE11
VDD33
21
112
PTE10
VDD
22
111
PTE9
PTE8
FLG
Ext_POR
23
110
VDDREG
24
109
PTE7
VSS
25
108
VDD33
BCTRL
26
107
VSS
TEST
27
106
PTE4
RESETB/RESET_OUT
28
105
PTE2
DACO0
29
104
PTE1
DACO1
30
103
PTE0
VDDA33_ADC
31
102
VDD
VSSA33_ADC
32
101
PTD13
VREFL_ADC
33
100
PTD12
VREFH_ADC
34
99
PTD11
VADCSE0
35
98
PTD10
VDD12_AFE
36
97
PTD9
VSS
VADCSE1
37
96
VSS12_AFE
38
95
VDD33
VSSA33_AFE
39
94
PTD8
PTD7
VDDA33_AFE
40
93
VADC_AFE_BANDGAP
41
92
PTD6
PTC31
42
91
PTD5
79
80
81
82
83
84
85
86
87
88
PTE21
PTE5
PTE6
VSS
VDD33
PTE22
VDD
PTD0
PTD1
PTD2
VSS
78
74
EXTAL
PTE13
73
XTAL
77
72
XTAL32
PTE3
71
EXTAL32
75
70
DECAP_V11_LDO_OUT
76
69
VDD33_LDOIN
PTA7
68
VSS
PTE14
66
67
VSS_KEL0
64
65
USB0_VBUS_DETECT
DECAP_V25_LDO_OUT
62
63
61
USB0_GND
USB0_DP
60
USB0_DM
59
USB_DCAP
USB0_VBUS
57
58
PTB27
PTC30
55
56
PTB5
PTB6
53
54
PTB3
PTB4
50
PTB1
51
49
PTB0
52
48
VDD
PTB2
47
PTA19
VDD33
46
PTD4
PTD3
45
90
89
VSS
43
44
PTA18
PTA16
PTA17
Figure 59. 176 LQFP Pinout Diagram
VF3xxR, VF5xxR, Rev7, 11/2014.
104
Freescale Semiconductor, Inc.
Pinouts
1
2
3
4
5
6
7
8
A
VSS
DDR_
CLK[0]
DDR_ZQ
DDR_
RAS_b
DDR_
CKE[0]
DDR_A[4]
DDR_A[7]
DDR_A[2]
12
13
14
15
16
17
18
19
20
DDR_A[6] DDR_A[13] DDR_A[8]
B
DDR_
ODT[1]
DDR_
CLK_b[0]
VSS
DDR_
CAS_b
VSS
DDR_A[5]
DDR_A[3]
VSS
C
DDR_D[13]
VSS
DDR_D[6]
DDR_
ODT[0]
DDR_
CS_b[0]
DDR_
WE_b
D
DDR_D[9] DDR_D[15]
DDR_
DQS[0]
DDR_
D[2]
SDRAMC_
VDD1P5
DDR_
RESET
PTE20
PTB20
PTB15
PTB17
PTB28
PTB26
PTB24
PTB23
VSS
A
DDR_A[9] DDR_A[15]
PTB18
VSS
PTB14
PTB10
VSS
PTB25
PTA20
VSS
PTE27
B
DDR_A[0] DDR_BA[0] DDR_BA[1] DDR_A[12] DDR_A[1]
VDD33
PTB19
PTB16
VDD33
PTC29
PTA23
VDD33
PTE25
PTE26
C
DDR_A[10] DDR_BA[2] DDR_A[14]
SDRAMC_
VDD1P5
PTB22
PTB7
PTB11
PTB13
PTC26
VSS
PTA21
PTE24
PTD16
D
VSS
PTB21
PTB12
VSS
PTC28
PTC27
PTA22
PTD18
VSS
PTD17
E
PTD19
PTD20
VDD33
PTD21
PTD22
F
SDRAMC_ SDRAMC_
VDD2P5
VDD1P5
VSS
9
10
DDR_
A[11]
SDRAMC_ SDRAMC_
VDD1P5
VDD2P5
11
VSS
E
DDR_
DQS[1]
DDR_
D[11]
DDR_
DQS_b[0]
SDRAMC_
VDD1P5
VSS
F
DDR_
DQS_b[1]
VSS
DDR_D[4]
DDR_
D[0]
SDRAMC_
VDD1P5
G
DDR_
D[12]
DDR_
DQM[1]
DDR_
D[7]
DDR_
D[3]
DDR_
VREF
VDD
VSS
VDD
VSS
VDD
VSS
VDD
VSS
PTD26
VSS
PTD25
PTD24
PTD23
G
H
DDR_
D[10]
DDR_
D[14]
DDR_
D[1]
VSS
SDRAMC_
VDD1P5
VSS
VDD
VSS
VDD
VSS
VDD
VSS
VDD
PTD27
PTD28
PTD29
VSS
PTD30
H
J
DDR_D[8]
VSS
DDR_D[5]
DDR_
DQM[0]
SDRAMC_
VDD2P5
VDD
VSS
VSS
VSS
VSS
VSS
VDD
VSS
PTB8
PTE23
VSS
PTB9
PTD31
J
K
JTDO
JTDI
VDD33
JTCLK/
SWCLK
SDRAMC_
VDD1P5
VSS
VDD
VSS
VSS
VSS
VSS
VSS
VDD
PTE28
VDD33
PTE19
PTE18
PTE17
K
L
JTMS
/SWDIO
PTC4
PTA12
PTC0
PTC1
VDD
VSS
VSS
VSS
VSS
VSS
VDD
VSS
PTE11
PTE12
PTE15
VSS
PTE16
L
M
PTC5
VSS
PTC3
VSS
PTC2
VSS
VDD
VSS
VSS
VSS
VSS
VSS
VDD
PTE10
PTE9
VSS
PTE8
PTE7
M
N
PTC6
PTC7
VDD33
PTC8
PTA6
FA_VDD
VSS
VDD
VSS
VDD
VSS
VDD
VSS
PTE0
VDD33
PTE1
PTE2
PTE4
N
P
PTC13
PTC15
PTC12
PTC11
VDDREG
VSS
VDD
VSS
VDD
VSS
VDD
VSS
VDD
PTA31
PTA30
PTA29
VSS
PTA28
P
R
PTC14
VSS
PTC16
PTC17
VSS12_
AFE
PTA24
PTA25
VSS
PTA26
PTA27
R
T
TEST2
BCTRL
TEST
RESETB
/RESET_
OUT
VDD12_
AFE
U
DACO0
DACO1
VREFL_
ADC
VADCSE1
V
VDDA33_
ADC
VSSA33_
ADC
VDDA33_
AFE
W
VREFH_
ADC
ADC0SE9
Y
VSS
1
PTB0
PTB1
PTC30
USB0_DM
USB0_DP
DECAP_
V25_LDO
_OUT
VADC_
AFE_
BANDGAP
PTA19
VSS
PTB27
USB1_
VBUS_
DETECT
EXT_TAMPER5
/EXT_WM1_
TAMPER_OUT
VSS_KEL0
VSSA33_
AFE
VADCSE3
PTA18
PTB2
VDD33
USB1_DM
USB0_
GND
VSS
ADC1SE8
VADCSE2
PTC31
VSS
PTB3
PTB6
USB1_DP
USB1_
VBUS
USB0_
VBUS
ADC0SE8
ADC1SE9
VADCSE0
PTA16
PTA17
PTB4
PTB5
USB1_GND
USB_
DCAP
USB0_
VBUS_
DETECT
2
3
4
5
6
7
8
9
10
11
VDD33_
LDOIN
EXT_TAMPER2
/EXT_WM0_
TAMPER_IN
EXT_TAMPER4 EXT_TAMPER3
/EXT_WM1_
/EXT_WM0_
TAMPER_IN
TAMPER_OUT
EXT_
TAMPER0
PTC9
PTE5
VDD33
PTD13
PTD12
PTD11
T
EXT_
TAMPER1
PTC10
VDD33
PTD8
PTD9
VSS
PTD10
U
DECAP_
V11_LDO_
OUT
VSS
VBAT
PTA7
PTE21
VSS
PTD2
PTD7
PTD6
V
XTAL32
XTAL
LVDS0P
PTE14
PTE6
PTE22
VDD33
PTD4
PTD5
W
EXTAL32
EXTAL
LVDS0N
PTE3
PTE13
PTD0
PTD1
PTD3
VSS
Y
12
13
14
15
16
17
18
19
20
Figure 60. 364-pin BGA package ballmap
12.2.1 GPIO Mapping
Table 78. RGPIO versus Pins
RGPIO
In GPIO module
Corresponding Pin
on the chip
IOMUX register name
IOMUX register
address
RGPIO[0]
PORT0[0]
PTA6
IOMUXC_PTA6
40048000
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
105
Pinouts
Table 78. RGPIO versus Pins (continued)
RGPIO
In GPIO module
Corresponding Pin
on the chip
IOMUX register name
IOMUX register
address
RGPIO[1]
PORT0[1]
PTA8
IOMUXC_PTA8
40048004
RGPIO[2]
PORT0[2]
PTA9
IOMUXC_PTA9
40048008
RGPIO[3]
PORT0[3]
PTA10
IOMUXC_PTA10
4004800C
RGPIO[4]
PORT0[4]
PTA11
IOMUXC_PTA11
40048010
RGPIO[5]
PORT0[5]
PTA12
IOMUXC_PTA12
40048014
RGPIO[6]
PORT0[6]
PTA16
IOMUXC_PTA16
40048018
RGPIO[7]
PORT0[7]
PTA17
IOMUXC_PTA17
4004801C
RGPIO[8]
PORT0[8]
PTA18
IOMUXC_PTA18
40048020
RGPIO[9]
PORT0[9]
PTA19
IOMUXC_PTA19
40048024
RGPIO[10]
PORT0[10]
PTA20
IOMUXC_PTA20
40048028
RGPIO[11]
PORT0[11]
PTA21
IOMUXC_PTA21
4004802C
RGPIO[12]
PORT0[12]
PTA22
IOMUXC_PTA22
40048030
RGPIO[13]
PORT0[13]
PTA23
IOMUXC_PTA23
40048034
RGPIO[14]
PORT0[14]
PTA24
IOMUXC_PTA24
40048038
RGPIO[15]
PORT0[15]
PTA25
IOMUXC_PTA25
4004803C
RGPIO[16]
PORT0[16]
PTA26
IOMUXC_PTA26
40048040
RGPIO[17]
PORT0[17]
PTA27
IOMUXC_PTA27
40048044
RGPIO[18]
PORT0[18]
PTA28
IOMUXC_PTA28
40048048
RGPIO[19]
PORT0[19]
PTA29
IOMUXC_PTA29
4004804C
RGPIO[20]
PORT0[20]
PTA30
IOMUXC_PTA30
40048050
RGPIO[21]
PORT0[21]
PTA31
IOMUXC_PTA31
40048054
RGPIO[22]
PORT0[22]
PTB0
IOMUXC_PTB0
40048058
RGPIO[23]
PORT0[23]
PTB1
IOMUXC_PTB1
4004805C
RGPIO[24]
PORT0[24]
PTB2
IOMUXC_PTB2
40048060
RGPIO[25]
PORT0[25]
PTB3
IOMUXC_PTB3
40048064
RGPIO[26]
PORT0[26]
PTB4
IOMUXC_PTB4
40048068
RGPIO[27]
PORT0[27]
PTB5
IOMUXC_PTB5
4004806C
RGPIO[28]
PORT0[28]
PTB6
IOMUXC_PTB6
40048070
RGPIO[29]
PORT0[29]
PTB7
IOMUXC_PTB7
40048074
RGPIO[30]
PORT0[30]
PTB8
IOMUXC_PTB8
40048078
RGPIO[31]
PORT0[31]
PTB9
IOMUXC_PTB9
4004807C
RGPIO[32]
PORT1[0]
PTB10
IOMUXC_PTB10
40048080
RGPIO[33]
PORT1[1]
PTB11
IOMUXC_PTB11
40048084
RGPIO[34]
PORT1[2]
PTB12
IOMUXC_PTB12
40048088
RGPIO[35]
PORT1[3]
PTB13
IOMUXC_PTB13
4004808C
RGPIO[36]
PORT1[4]
PTB14
IOMUXC_PTB14
40048090
RGPIO[37]
PORT1[5]
PTB15
IOMUXC_PTB15
40048094
RGPIO[38]
PORT1[6]
PTB16
IOMUXC_PTB16
40048098
RGPIO[39]
PORT1[7]
PTB17
IOMUXC_PTB17
4004809C
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
106
Freescale Semiconductor, Inc.
Pinouts
Table 78. RGPIO versus Pins (continued)
RGPIO
In GPIO module
Corresponding Pin
on the chip
IOMUX register name
IOMUX register
address
RGPIO[40]
PORT1[8]
PTB18
IOMUXC_PTB18
400480A0
RGPIO[41]
PORT1[9]
PTB19
IOMUXC_PTB19
400480A4
RGPIO[42]
PORT1[10]
PTB20
IOMUXC_PTB20
400480A8
RGPIO[43]
PORT1[11]
PTB21
IOMUXC_PTB21
400480AC
RGPIO[44]
PORT1[12]
PTB22
IOMUXC_PTB22
400480B0
RGPIO[45]
PORT1[13]
PTC0
IOMUXC_PTC0
400480B4
RGPIO[46]
PORT1[14]
PTC1
IOMUXC_PTC1
400480B8
RGPIO[47]
PORT1[15]
PTC2
IOMUXC_PTC2
400480BC
RGPIO[48]
PORT1[16]
PTC3
IOMUXC_PTC3
400480C0
RGPIO[49]
PORT1[17]
PTC4
IOMUXC_PTC4
400480C4
RGPIO[50]
PORT1[18]
PTC5
IOMUXC_PTC5
400480C8
RGPIO[51]
PORT1[19]
PTC6
IOMUXC_PTC6
400480CC
RGPIO[52]
PORT1[20]
PTC7
IOMUXC_PTC7
400480D0
RGPIO[53]
PORT1[21]
PTC8
IOMUXC_PTC8
400480D4
RGPIO[54]
PORT1[22]
PTC9
IOMUXC_PTC9
400480D8
RGPIO[55]
PORT1[23]
PTC10
IOMUXC_PTC10
400480DC
RGPIO[56]
PORT1[24]
PTC11
IOMUXC_PTC11
400480E0
RGPIO[57]
PORT1[25]
PTC12
IOMUXC_PTC12
400480E4
RGPIO[58]
PORT1[26]
PTC13
IOMUXC_PTC13
400480E8
RGPIO[59]
PORT1[27]
PTC14
IOMUXC_PTC14
400480EC
RGPIO[60]
PORT1[28]
PTC15
IOMUXC_PTC15
400480F0
RGPIO[61]
PORT1[29]
PTC16
IOMUXC_PTC16
400480F4
RGPIO[62]
PORT1[30]
PTC17
IOMUXC_PTC17
400480F8
RGPIO[63]
PORT1[31]
PTD31
IOMUXC_PTD31
400480FC
RGPIO[64]
PORT2[0]
PTD30
IOMUXC_PTD30
40048100
RGPIO[65]
PORT2[1]
PTD29
IOMUXC_PTD29
40048104
RGPIO[66]
PORT2[2]
PTD28
IOMUXC_PTD28
40048108
RGPIO[67]
PORT2[3]
PTD27
IOMUXC_PTD27
4004810C
RGPIO[68]
PORT2[4]
PTD26
IOMUXC_PTD26
40048110
RGPIO[69]
PORT2[5]
PTD25
IOMUXC_PTD25
40048114
RGPIO[70]
PORT2[6]
PTD24
IOMUXC_PTD24
40048118
RGPIO[71]
PORT2[7]
PTD23
IOMUXC_PTD23
4004811C
RGPIO[72]
PORT2[8]
PTD22
IOMUXC_PTD22
40048120
RGPIO[73]
PORT2[9]
PTD21
IOMUXC_PTD21
40048124
RGPIO[74]
PORT2[10]
PTD20
IOMUXC_PTD20
40048128
RGPIO[75]
PORT2[11]
PTD19
IOMUXC_PTD19
4004812C
RGPIO[76]
PORT2[12]
PTD18
IOMUXC_PTD18
40048130
RGPIO[77]
PORT2[13]
PTD17
IOMUXC_PTD17
40048134
RGPIO[78]
PORT2[14]
PTD16
IOMUXC_PTD16
40048138
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
107
Pinouts
Table 78. RGPIO versus Pins (continued)
RGPIO
In GPIO module
Corresponding Pin
on the chip
IOMUX register name
IOMUX register
address
RGPIO[79]
PORT2[15]
PTD0
IOMUXC_PTD0
4004813C
RGPIO[80]
PORT2[16]
PTD1
IOMUXC_PTD1
40048140
RGPIO[81]
PORT2[17]
PTD2
IOMUXC_PTD2
40048144
RGPIO[82]
PORT2[18]
PTD3
IOMUXC_PTD3
40048148
RGPIO[83]
PORT2[19]
PTD4
IOMUXC_PTD4
4004814C
RGPIO[84]
PORT2[20]
PTD5
IOMUXC_PTD5
40048150
RGPIO[85]
PORT2[21]
PTD6
IOMUXC_PTD6
40048154
RGPIO[86]
PORT2[22]
PTD7
IOMUXC_PTD7
40048158
RGPIO[87]
PORT2[23]
PTD8
IOMUXC_PTD8
4004815C
RGPIO[88]
PORT2[24]
PTD9
IOMUXC_PTD9
40048160
RGPIO[89]
PORT2[25]
PTD10
IOMUXC_PTD10
40048164
RGPIO[90]
PORT2[26]
PTD11
IOMUXC_PTD11
40048168
RGPIO[91]
PORT2[27]
PTD12
IOMUXC_PTD12
4004816C
RGPIO[92]
PORT2[28]
PTD13
IOMUXC_PTD13
40048170
RGPIO[93]
PORT2[29]
PTB23
IOMUXC_PTB23
40048174
RGPIO[94]
PORT2[30]
PTB24
IOMUXC_PTB24
40048178
RGPIO[95]
PORT2[31]
PTB25
IOMUXC_PTB25
4004817C
RGPIO[96]
PORT3[0]
PTB26
IOMUXC_PTB26
40048180
RGPIO[97]
PORT3[1]
PTB27
IOMUXC_PTB27
40048184
RGPIO[98]
PORT3[2]
PTB28
IOMUXC_PTB28
40048188
RGPIO[99]
PORT3[3]
PTC26
IOMUXC_PTC26
4004818C
RGPIO[100]
PORT3[4]
PTC27
IOMUXC_PTC27
40048190
RGPIO[101]
PORT3[5]
PTC28
IOMUXC_PTC28
40048194
RGPIO[102]
PORT3[6]
PTC29
IOMUXC_PTC29
40048198
RGPIO[103]
PORT3[7]
PTC30
IOMUXC_PTC30
4004819C
RGPIO[104]
PORT3[8]
PTC31
IOMUXC_PTC31
400481A0
RGPIO[105]
PORT3[9]
PTE0
IOMUXC_PTE0
400481A4
RGPIO[106]
PORT3[10]
PTE1
IOMUXC_PTE1
400481A8
RGPIO[107]
PORT3[11]
PTE2
IOMUXC_PTE2
400481AC
RGPIO[108]
PORT3[12]
PTE3
IOMUXC_PTE3
400481B0
RGPIO[109]
PORT3[13]
PTE4
IOMUXC_PTE4
400481B4
RGPIO[110]
PORT3[14]
PTE5
IOMUXC_PTE5
400481B8
RGPIO[111]
PORT3[15]
PTE6
IOMUXC_PTE6
400481BC
RGPIO[112]
PORT3[16]
PTE7
IOMUXC_PTE7
400481C0
RGPIO[113]
PORT3[17]
PTE8
IOMUXC_PTE8
400481C4
RGPIO[114]
PORT3[18]
PTE9
IOMUXC_PTE9
400481C8
RGPIO[115]
PORT3[19]
PTE10
IOMUXC_PTE10
400481CC
RGPIO[116]
PORT3[20]
PTE11
IOMUXC_PTE11
400481D0
RGPIO[117]
PORT3[21]
PTE12
IOMUXC_PTE12
400481D4
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
108
Freescale Semiconductor, Inc.
Pinouts
Table 78. RGPIO versus Pins (continued)
RGPIO
In GPIO module
Corresponding Pin
on the chip
IOMUX register name
IOMUX register
address
RGPIO[118]
PORT3[22]
PTE13
IOMUXC_PTE13
400481D8
RGPIO[119]
PORT3[23]
PTE14
IOMUXC_PTE14
400481DC
RGPIO[120]
PORT3[24]
PTE15
IOMUXC_PTE15
400481E0
RGPIO[121]
PORT3[25]
PTE16
IOMUXC_PTE16
400481E4
RGPIO[122]
PORT3[26]
PTE17
IOMUXC_PTE17
400481E8
RGPIO[123]
PORT3[27]
PTE18
IOMUXC_PTE18
400481EC
RGPIO[124]
PORT3[28]
PTE19
IOMUXC_PTE19
400481F0
RGPIO[125]
PORT3[29]
PTE20
IOMUXC_PTE20
400481F4
RGPIO[126]
PORT3[30]
PTE21
IOMUXC_PTE21
400481F8
RGPIO[127]
PORT3[31]
PTE22
IOMUXC_PTE22
400481FC
RGPIO[128]
PORT4[0]
PTE23
IOMUXC_PTE23
40048200
RGPIO[129]
PORT4[1]
PTE24
IOMUXC_PTE24
40048204
RGPIO[130]
PORT4[2]
PTE25
IOMUXC_PTE25
40048208
RGPIO[131]
PORT4[3]
PTE26
IOMUXC_PTE26
4004820C
RGPIO[132]
PORT4[4]
PTE27
IOMUXC_PTE27
40048210
RGPIO[133]
PORT4[5]
PTE28
IOMUXC_PTE28
40048214
RGPIO[134]
PORT4[6]
PTA7
IOMUXC_PTA7
40048218
12.2.2 Special Signal
Table 79. Special Signal Considerations
Special Signal
Comments
DDR_VREF
When using DDR_VREF with DDR I/O, the nominal reference
voltage must be half of the SDRAMC_VDD1P5 supply. The
user must tie DDR_VREF to a precision external resistor
divider. Shunt each resistor with a closely-mounted 0.1 μF
capacitor.
DDR_ZQ
DRAM calibration resistor 240 Ω 1% used as reference during
DRAM output buffer driver calibration should be connected
between this pad and GND
DECAP_V25_LDO_OUT
DCAP_V25_LDO_OUT can be tied to SDRAMC_VDD2P5 to
provide the predriver supply for the DDR I/O segment.
SDRAMC_VDD1P5 requires an external regulated supply. If
SDRAMC_VDD2P5 uses an external 2.5V supply, do NOT tie
it to DCAP_V25_LDO_OUT.
EXT_POR, TEST
Factory use only, tie to ground..
EXT_TAMPER0, EXT_TAMPER1, EXT_TAMPER2,
EXT_TAMPER3, EXT_TAMPER4, EXT_TAMPER5
Security related tamper detection inputs, if not in use they
must be tied to ground.
FA_VDD
Factory use only, tie to VDD.
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
109
Pinouts
Table 79. Special Signal Considerations (continued)
Special Signal
Comments
JTCLK, JTDI, JTDO, JTMS
For JTAG the use of external resistors is unnecessary.
However, if external resistors are used, the user must ensure
that the on-chip pull-up/down configuration is matched. For
example, do not use an external pull down on an input that
has on-chip pull-up. JTDO is configured with a keeper circuit
such that the floating condition is eliminated if an external pull
resistor is not present. An external pull resistor on JTDO is
detrimental and should be avoided.
LVDS0N, LVDS0P
Not recommended for application use, intended for clock
observation purposes during debug only.
RESETB/RESET_OUT
Active low input used to generate a system wide reset (except
the SRTC). A glitch filter is include to help prevent
unexpected resets, a minimum pulse width of 125 nsecs is
required to guarantee a reset is detected.
XTAL, EXTAL
A 24.0 MHz fundamental mode crystal should be connected
between XTAL and EXTAL. The crystal must be rated for a
drive level of 250 μW or higher. An ESR (equivalent series
resistance) of 80 Ω or less is recommended. This clock is
used as a reference for USB, so there are strict frequency
tolerance and jitter requirements. The crystal can be
eliminated if an external 24 MHz oscillator is available in the
system. In this case, XTAL must be directly driven by the
external oscillator and EXTAL floated. The XTAL signal level
must swing from ~0.8 x DECAP_V11_ LDO_OUT to ~0.2 V.
XTAL32, EXTAL32
If the user wishes to configure XTAL32 and EXTAL32 as an
RTC oscillator, a 32.768 kHz crystal, (≤50 kΩ ESR, 10 pF
load) should be connected between XTAL32 and EXTAL32.
Keep in mind the capacitors implemented on either side of the
crystal are about twice the crystal load capacitor. To hit the
exact oscillation frequency, the board capacitors need to be
reduced to account for board and chip parasitics. The
integrated oscillation amplifier is self biasing, but relatively
weak. Care must be taken to limit parasitic leakage from
XTAL32 and EXTAL32 to either power or ground (>100 MΩ).
This will debias the amplifier and cause a reduction of startup
margin. Typically XTAL32 and EXTAL32 should bias to
approximately 0.5 V. If it is desired to feed an external low
frequency clock into XTAL32 the EXTAL32 pin should be left
floating or driven with a complimentary signal. The logic level
of this forcing clock should not exceed DECAP_V11_
LDO_OUT level and the frequency should be <100 kHz under
typical conditions. In the case where the SIRC is used, it is
recommended to connect XTAL32 to ground and leave
EXTAL32 floating.
VF3xxR, VF5xxR, Rev7, 11/2014.
110
Freescale Semiconductor, Inc.
Power Supply Pins
13 Power Supply Pins
13.1 Power Supply Pins
Table 80. Power Supply Pins
Supply Rail Name
364 MAP BGA
176 LQFP (R-series ONLY)
Comment
DECAP_V11_ LDO_OUT
V12
69
On-chip 1.1V LDO output
DECAP_V25_ LDO_OUT
T11
65
On-chip 2.5V LDO output
(Intended to supply DRAM IO
when required)
FA_VDD
N7
—
Factory Use Only (Connect to
VDD, internally bonded in
LQFP)
SDRAMC_ VDD1P5
D5, D11, E4, E7, E9, F5, H5,
K5
DRAM not supported in LQFP 1.5V DDR3 DRAM Supply
(1.2V for LPDDR2)
SDRAMC_ VDD2P5
E6, E10, J5
DRAM not supported in LQFP 2.5V DRAM Supply
USB_DCAP
Y10
59
USB0_GND
V10
61
USB1_GND
Y9
USB1 not supported in LQFP
VADC_AFE_ BANDGAP
U5
41
Video ADC Bandgap Output
VBAT
V14
VBAT not supported in LQFP
On-chip SNVS regulator
battery back-up supply option
VDD
G7, G9, G11, G13, H8, H10,
H12, H14, J7, J13, K8, K14,
L7, L13, M8, M14, N9, N11,
N13, P8, P10, P12, P14
2, 22, 48, 85, 102, 125, 136,
174
1.2V Core Supply (Internally
Regulated)
VDD33
C12, C15, C18, F18, K3, K17, 10, 21, 52, 83, 95, 108, 127,
N3, N17, T17, U16, V8, W18 140, 146, 158, 168
3.3V IO Supply
VDDA33_ADC
V1
31
3.3V Analog To Digital
convertor supply
VDD12_AFE
T5
36
1.2V Analog Front End supply
for Video ADC
VDDA33_AFE
V3
40
3.3V Analog Front End supply
for Video ADC
VDD33_ LDOIN
T12
68
On-chip 2.5V LDO, 1.1V LDO
and SNVS regulators input
supply
VDDREG
P5
24
On-chip HPREG, LPREG,
WBREG and ULPREG
regulators input supply
VREFH_ADC
W1
34
ATD High Voltage Reference
VREFL_ADC
U3
33
ATD Low Voltage Reference
On-chip 3V LDO output
(Intended to be fed by
external USB VBUS supply)
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
111
Functional Assignment Pins
Table 80. Power Supply Pins (continued)
Supply Rail Name
364 MAP BGA
176 LQFP (R-series ONLY)
Comment
VSS
A1, A20, B3, B5, B8, B11,
1, 13, 20, 25, 45, 67, 74, 82,
B13, B16, B19, C2, D17, E5, 96, 107, 139, 144, 157, 175,
E8, E11, E14, E19, F2, G8,
176, FLG
G10, G12, G14, G17, H4, H7,
H9, H11, H13, H19, J2, J8,
J9, J10, J11, J12, J14, J18,
K7, K9, K10, K11, K12, K13,
L8, L9, L10, L11, L12, L14,
L19, M2, M4, M7, M9, M10,
M11, M12, M13, M18, N8,
N10, N12, N14, P7, P9, P11,
P13, P19, R2, R18, U7, U19,
V11, V13, V17, W6, Y1, Y20
Ground. Connect "Flag pad
(FLG)" to the internal GND
plane with numerous vias—for
both electrical and thermal
purposes.
VSSA33_ADC
V2
32
ATD Ground
VSS12_AFE
R5
38
Video ADC Ground
VSSA33_AFE
V4
39
Video ADC Ground
VSS_KEL0
U11
66
Ground (VSS and VSS_KEL0
are NOT connected internally)
14 Functional Assignment Pins
14.1 Functional Assignment Pins
Table 81. Functional Assignment Pins
Signal
Name
364 MAP
BGA
176 LQFP
(R-series
ONLY)
Power
Group
ADC0SE8
Y2
—
VDDA33_A Analog
DC
—
ADC0SE8
—
—
ADC0SE9
W2
—
VDDA33_A Analog
DC
—
ADC0SE9
—
—
ADC1SE8
W3
—
VDDA33_A Analog
DC
—
ADC1SE8
—
—
ADC1SE9
Y3
—
VDDA33_A Analog
DC
—
ADC1SE9
—
—
BCTRL
T2
26
Analog
—
BCTRL
—
—
DACO0
U1
29
VDDA33_A Analog
DC
—
DACO0
—
—
DACO1
U2
30
VDDA33_A Analog
DC
—
DACO1
—
—
DDR_A[0]
C7
—
SDRAMC_ DDR
VDD2P5
—
DDR_A[0]
—
—
VDDREG
Pad Type
Default
Mode
(Reset)
Default
Function
Input/
Output
Value
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
112
Freescale Semiconductor, Inc.
Functional Assignment Pins
Table 81. Functional Assignment Pins
(continued)
Signal
Name
364 MAP
BGA
176 LQFP
(R-series
ONLY)
Power
Group
Pad Type
Default
Mode
(Reset)
Default
Function
Input/
Output
Value
DDR_A[1]
C11
—
SDRAMC_ DDR
VDD2P5
—
DDR_A[1]
—
—
DDR_A[2]
A8
—
SDRAMC_ DDR
VDD2P5
—
DDR_A[2]
—
—
DDR_A[3]
B7
—
SDRAMC_ DDR
VDD2P5
—
DDR_A[3]
—
—
DDR_A[4]
A6
—
SDRAMC_ DDR
VDD2P5
—
DDR_A[4]
—
—
DDR_A[5]
B6
—
SDRAMC_ DDR
VDD2P5
—
DDR_A[5]
—
—
DDR_A[6]
A9
—
SDRAMC_ DDR
VDD2P5
—
DDR_A[6]
—
—
DDR_A[7]
A7
—
SDRAMC_ DDR
VDD2P5
—
DDR_A[7]
—
—
DDR_A[8]
A11
—
SDRAMC_ DDR
VDD2P5
—
DDR_A[8]
—
—
DDR_A[9]
B9
—
SDRAMC_ DDR
VDD2P5
—
DDR_A[9]
—
—
DDR_A[10]
D7
—
SDRAMC_ DDR
VDD2P5
—
DDR_A[10]
—
—
DDR_A[11]
D10
—
SDRAMC_ DDR
VDD2P5
—
DDR_A[11]
—
—
DDR_A[12]
C10
—
SDRAMC_ DDR
VDD2P5
—
DDR_A[12]
—
—
DDR_A[13]
A10
—
SDRAMC_ DDR
VDD2P5
—
DDR_A[13]
—
—
DDR_A[14]
D9
—
SDRAMC_ DDR
VDD2P5
—
DDR_A[14]
—
—
DDR_A[15]
B10
—
SDRAMC_ DDR
VDD2P5
—
DDR_A[15]
—
—
DDR_BA[0]
C8
—
SDRAMC_ DDR
VDD2P5
—
DDR_BA[0]
—
—
DDR_BA[1]
C9
—
SDRAMC_ DDR
VDD2P5
—
DDR_BA[1]
—
—
DDR_BA[2]
D8
—
SDRAMC_ DDR
VDD2P5
—
DDR_BA[2]
—
—
DDR_CAS_
b
B4
—
SDRAMC_ DDR
VDD2P5
—
DDR_CAS_ —
b
—
DDR_CKE[0
]
A5
—
SDRAMC_ DDR
VDD2P5
—
DDR_CKE[0 —
]
—
DDR_CLK[0
]
A2
—
SDRAMC_ DDR
VDD2P5
—
DDR_CLK[0 —
]
—
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
113
Functional Assignment Pins
Table 81. Functional Assignment Pins
(continued)
Signal
Name
364 MAP
BGA
176 LQFP
(R-series
ONLY)
Power
Group
Pad Type
Default
Mode
(Reset)
Default
Function
Input/
Output
DDR_CLK_
b[0]
B2
—
SDRAMC_ DDR
VDD2P5
—
DDR_CLK_ —
b[0]
—
DDR_CS_b[
0]
C5
—
SDRAMC_ DDR
VDD2P5
—
DDR_CS_b[ —
0]
—
DDR_D[0]
F4
—
SDRAMC_ DDR
VDD2P5
—
DDR_D[0]
—
—
DDR_D[1]
H3
—
SDRAMC_ DDR
VDD2P5
—
DDR_D[1]
—
—
DDR_D[2]
D4
—
SDRAMC_ DDR
VDD2P5
—
DDR_D[2]
—
—
DDR_D[3]
G4
—
SDRAMC_ DDR
VDD2P5
—
DDR_D[3]
—
—
DDR_D[4]
F3
—
SDRAMC_ DDR
VDD2P5
—
DDR_D[4]
—
—
DDR_D[5]
J3
—
SDRAMC_ DDR
VDD2P5
—
DDR_D[5]
—
—
DDR_D[6]
C3
—
SDRAMC_ DDR
VDD2P5
—
DDR_D[6]
—
—
DDR_D[7]
G3
—
SDRAMC_ DDR
VDD2P5
—
DDR_D[7]
—
—
DDR_D[8]
J1
—
SDRAMC_ DDR
VDD2P5
—
DDR_D[8]
—
—
DDR_D[9]
D1
—
SDRAMC_ DDR
VDD2P5
—
DDR_D[9]
—
—
DDR_D[10]
H1
—
SDRAMC_ DDR
VDD2P5
—
DDR_D[10]
—
—
DDR_D[11]
E2
—
SDRAMC_ DDR
VDD2P5
—
DDR_D[11]
—
—
DDR_D[12]
G1
—
SDRAMC_ DDR
VDD2P5
—
DDR_D[12]
—
—
DDR_D[13]
C1
—
SDRAMC_ DDR
VDD2P5
—
DDR_D[13]
—
—
DDR_D[14]
H2
—
SDRAMC_ DDR
VDD2P5
—
DDR_D[14]
—
—
DDR_D[15]
D2
—
SDRAMC_ DDR
VDD2P5
—
DDR_D[15]
—
—
DDR_DQM[
0]
J4
—
SDRAMC_ DDR
VDD2P5
—
DDR_DQM[ —
0]
—
DDR_DQM[
1]
G2
—
SDRAMC_ DDR
VDD2P5
—
DDR_DQM[ —
1]
—
DDR_DQS[
0]
D3
—
SDRAMC_ DDR
VDD2P5
—
DDR_DQS[
0]
—
—
Value
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
114
Freescale Semiconductor, Inc.
Functional Assignment Pins
Table 81. Functional Assignment Pins
(continued)
Signal
Name
364 MAP
BGA
176 LQFP
(R-series
ONLY)
Power
Group
Pad Type
Default
Mode
(Reset)
Default
Function
Input/
Output
Value
DDR_DQS_
b[0]
E3
—
SDRAMC_ DDR
VDD2P5
—
DDR_DQS_ —
b[0]
—
DDR_DQS[
1]
E1
—
SDRAMC_ DDR
VDD2P5
—
DDR_DQS[
1]
—
—
DDR_DQS_
b[1]
F1
—
SDRAMC_ DDR
VDD2P5
—
DDR_DQS_ —
b[1]
—
DDR_ODT[0
]
C4
—
SDRAMC_ DDR
VDD2P5
—
DDR_ODT[0 —
]
—
DDR_ODT[1
]
B1
—
SDRAMC_ DDR
VDD2P5
—
DDR_ODT[1 —
]
—
DDR_RAS_
b
A4
—
SDRAMC_ DDR
VDD2P5
—
DDR_RAS_ —
b
—
DDR_RESE
T
D6
—
SDRAMC_ DDR
VDD2P5
—
DDR_RESE —
T
—
DDR_VREF
G5
—
SDRAMC_ DDR
VDD2P5
—
DDR_VREF —
—
DDR_WE_b
C6
—
SDRAMC_ DDR
VDD2P5
—
DDR_WE_b —
—
DDR_ZQ
A3
—
SDRAMC_ DDR
VDD2P5
—
DDR_ZQ
—
—
EXT_POR
T1
23
VDD33
GPIO
—
EXT_POR
—
—
EXT_TAMP
ER0
T14
—
VBAT
Analog
—
EXT_TAMP —
ER0
—
EXT_TAMP
ER1
U14
—
VBAT
Analog
—
EXT_TAMP —
ER1
—
EXT_TAMP
ER2/
EXT_WM0_
TAMPER_I
N
T13
—
VBAT
Analog
—
EXT_TAMP —
ER2/
EXT_WM0_
TAMPER_I
N
—
EXT_TAMP
ER3/
EXT_WM0_
TAMPER_
OUT
U13
—
VBAT
Analog
—
EXT_TAMP —
ER3/
EXT_WM0_
TAMPER_
OUT
—
EXT_TAMP
ER4/
EXT_WM1_
TAMPER_I
N
U12
—
VBAT
Analog
—
EXT_TAMP —
ER4/
EXT_WM1_
TAMPER_I
N
—
EXT_TAMP
ER5/
EXT_WM1_
TAMPER_
OUT
U10
—
VBAT
Analog
—
EXT_TAMP —
ER5/
EXT_WM1_
TAMPER_
OUT
—
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
115
Functional Assignment Pins
Table 81. Functional Assignment Pins
(continued)
Signal
Name
364 MAP
BGA
176 LQFP
(R-series
ONLY)
Power
Group
Pad Type
Default
Mode
(Reset)
Default
Function
Input/
Output
Value
EXTAL
Y13
73
DECAP_V1 Analog
1_
LDO_OUT
—
EXTAL
—
—
EXTAL32
Y12
70
DECAP_V1 Analog
1_
LDO_OUT
—
EXTAL32
—
—
JTCLK/
SWCLK
K4
3
VDD33
GPIO
ALT1
JTAG
Input
100K PU
JTDI
K2
4
VDD33
GPIO
ALT1
JTAG
Input
100K PU
JTDO
K1
5
VDD33
GPIO
ALT1
JTAG
Disabled
—
JTMS/
SWDIO
L1
6
VDD33
GPIO
ALT1
JTAG
Input
100K PU
LVDS0P
W14
—
DECAP_V2 Analog
5_
LDO_OUT
—
LVDS0P
—
—
LVDS0N
Y14
—
DECAP_V2 Analog
5_
LDO_OUT
—
LVDS0N
—
—
PTA6
N5
19
VDD33
GPIO
ALT0
GPIO
Disabled
PTA7
V15
75
VDD33
GPIO
ALT0
GPIO
Disabled
PTA12
L3
7
VDD33
GPIO
ALT0
GPIO
Disabled
PTA16
Y5
43
VDD33
GPIO
ALT0
GPIO
Disabled
PTA17
Y6
44
VDD33
GPIO
ALT0
GPIO
Disabled
PTA18
V6
46
VDD33
GPIO
ALT0
GPIO
Disabled
PTA19
U6
47
VDD33
GPIO
ALT0
GPIO
Disabled
PTA20
B18
143
VDD33
GPIO
ALT0
GPIO
Disabled
PTA21
D18
145
VDD33
GPIO
ALT0
GPIO
Disabled
PTA22
E17
147
VDD33
GPIO
ALT0
GPIO
Disabled
PTA23
C17
148
VDD33
GPIO
ALT0
GPIO
Disabled
PTA24
R16
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTA25
R17
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTA26
R19
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTA27
R20
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTA28
P20
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTA29
P18
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTA30
P17
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTA31
P16
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTB0
T6
49
VDD33
GPIO
ALT0
GPIO
Disabled
PTB1
T7
50
VDD33
GPIO
ALT3
RCON30
Input
Disabled
PTB2
V7
51
VDD33
GPIO
ALT3
RCON31
Input
Disabled
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
116
Freescale Semiconductor, Inc.
Functional Assignment Pins
Table 81. Functional Assignment Pins
(continued)
Signal
Name
364 MAP
BGA
176 LQFP
(R-series
ONLY)
Power
Group
Pad Type
Default
Mode
(Reset)
Default
Function
Input/
Output
PTB3
W7
53
VDD33
GPIO
ALT0
GPIO
Disabled
PTB4
Y7
54
VDD33
GPIO
ALT0
GPIO
Disabled
PTB5
Y8
55
VDD33
GPIO
ALT0
GPIO
Disabled
PTB6
W8
56
VDD33
GPIO
ALT0
GPIO
Disabled
PTB7
D13
166
VDD33
GPIO
ALT0
GPIO
Disabled
PTB8
J16
121
VDD33
GPIO
ALT0
GPIO
Disabled
Value
PTB9
J19
123
VDD33
GPIO
ALT0
GPIO
Disabled
PTB10
B15
159
VDD33
GPIO
ALT0
GPIO
Disabled
PTB11
D14
164
VDD33
GPIO
ALT0
GPIO
Disabled
PTB12
E13
165
VDD33
GPIO
ALT0
GPIO
Disabled
PTB13
D15
156
VDD33
GPIO
ALT0
GPIO
Disabled
PTB14
B14
162
VDD33
GPIO
ALT0
GPIO
Disabled
PTB15
A14
161
VDD33
GPIO
ALT0
GPIO
Disabled
PTB16
C14
163
VDD33
GPIO
ALT0
GPIO
Disabled
PTB17
A15
160
VDD33
GPIO
ALT0
GPIO
Disabled
PTB18
B12
171
VDD33
GPIO
ALT0
GPIO
Input
Disabled
PTB19
C13
167
VDD33
GPIO
ALT0
GPIO
Input
Disabled
PTB20
A13
169
VDD33
GPIO
ALT0
GPIO
Disabled
PTB21
E12
173
VDD33
GPIO
ALT0
GPIO
Disabled
PTB22
D12
172
VDD33
GPIO
ALT0
GPIO
Disabled
PTB23
A19
141
VDD33
GPIO
ALT3
GPIO
Disabled
PTB24
A18
142
VDD33
GPIO
ALT3
GPIO
Disabled
PTB25
B17
149
VDD33
GPIO
ALT3
GPIO
Disabled
PTB26
A17
150
VDD33
GPIO
ALT3
RCON21
Input
Disabled
PTB27
U8
57
VDD33
GPIO
ALT3
RCON22
Input
Disabled
PTB28
A16
151
VDD33
GPIO
ALT3
RCON23
Input
Disabled
PTC0
L4
8
VDD33
GPIO
ALT7
RCON18
Input
Disabled
PTC1
L5
9
VDD33
GPIO
ALT7
RCON19
Input
Disabled
PTC2
M5
11
VDD33
GPIO
ALT7
RCON20
Input
Disabled
PTC3
M3
12
VDD33
GPIO
ALT0
GPIO
Disabled
PTC4
L2
14
VDD33
GPIO
ALT0
GPIO
Disabled
PTC5
M1
15
VDD33
GPIO
ALT0
GPIO
Disabled
PTC6
N1
16
VDD33
GPIO
ALT0
GPIO
Disabled
PTC7
N2
17
VDD33
GPIO
ALT0
GPIO
Disabled
PTC8
N4
18
VDD33
GPIO
ALT0
GPIO
Disabled
PTC9
T15
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTC10
U15
—
VDD33
GPIO
ALT0
GPIO
Disabled
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
117
Functional Assignment Pins
Table 81. Functional Assignment Pins
(continued)
Signal
Name
364 MAP
BGA
176 LQFP
(R-series
ONLY)
Power
Group
Pad Type
Default
Mode
(Reset)
Default
Function
Input/
Output
PTC11
P4
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTC12
P3
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTC13
P1
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTC14
R1
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTC15
P2
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTC16
R3
—
VDD33
GPIO
ALT0
GPIO
Disabled
Value
PTC17
R4
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTC26
D16
153
VDD33
GPIO
ALT3
RCON24
Input
Disabled
PTC27
E16
154
VDD33
GPIO
ALT3
RCON25
Input
Disabled
PTC28
E15
155
VDD33
GPIO
ALT3
RCON26
Input
Disabled
PTC29
C16
152
VDD33
GPIO
ALT3
RCON27
Input
Disabled
PTC30
T8
58
VDD33
GPIO
ALT3
RCON28
Input
Disabled
PTC31
W5
42
VDD33
GPIO
ALT3
RCON29
Input
Disabled
PTD0
Y17
86
VDD33
GPIO
ALT0
GPIO
Disabled
PTD1
Y18
87
VDD33
GPIO
ALT0
GPIO
Disabled
PTD2
V18
88
VDD33
GPIO
ALT0
GPIO
Disabled
PTD3
Y19
89
VDD33
GPIO
ALT0
GPIO
Disabled
PTD4
W19
90
VDD33
GPIO
ALT0
GPIO
Disabled
PTD5
W20
91
VDD33
GPIO
ALT0
GPIO
Disabled
PTD6
V20
92
VDD33
GPIO
ALT0
GPIO
Disabled
PTD7
V19
93
VDD33
GPIO
ALT0
GPIO
Disabled
PTD8
U17
94
VDD33
GPIO
ALT0
GPIO
Disabled
PTD9
U18
97
VDD33
GPIO
ALT0
GPIO
Disabled
PTD10
U20
98
VDD33
GPIO
ALT0
GPIO
Disabled
PTD11
T20
99
VDD33
GPIO
ALT0
GPIO
Disabled
PTD12
T19
100
VDD33
GPIO
ALT0
GPIO
Disabled
PTD13
T18
101
VDD33
GPIO
ALT0
GPIO
Disabled
PTD16
D20
133
VDD33
GPIO
ALT0
GPIO
Disabled
PTD17
E20
132
VDD33
GPIO
ALT0
GPIO
Disabled
PTD18
E18
131
VDD33
GPIO
ALT0
GPIO
Disabled
PTD19
F16
130
VDD33
GPIO
ALT0
GPIO
Disabled
PTD20
F17
129
VDD33
GPIO
ALT0
GPIO
Disabled
PTD21
F19
128
VDD33
GPIO
ALT0
GPIO
Disabled
PTD22
F20
126
VDD33
GPIO
ALT0
GPIO
Disabled
PTD23
G20
124
VDD33
GPIO
ALT0
GPIO
Disabled
PTD24
G19
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTD25
G18
—
VDD33
GPIO
ALT0
GPIO
Disabled
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
118
Freescale Semiconductor, Inc.
Functional Assignment Pins
Table 81. Functional Assignment Pins
(continued)
Signal
Name
364 MAP
BGA
176 LQFP
(R-series
ONLY)
Power
Group
Pad Type
Default
Mode
(Reset)
Default
Function
Input/
Output
Value
PTD26
G16
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTD27
H16
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTD28
H17
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTD29
H18
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTD30
H20
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTD31
J20
—
VDD33
GPIO
ALT0
GPIO
Disabled
PTE0
N16
103
VDD33
GPIO
ALT2
BMODE1
Input
Disabled
PTE1
N18
104
VDD33
GPIO
ALT2
BMODE0
Input
Disabled
PTE2
N19
105
VDD33
GPIO
ALT0
GPIO
Disabled
PTE3
Y15
77
VDD33
GPIO
ALT0
GPIO
Disabled
PTE4
N20
106
VDD33
GPIO
ALT0
GPIO
Disabled
PTE5
T16
80
VDD33
GPIO
ALT0
GPIO
Disabled
PTE6
W16
81
VDD33
GPIO
ALT0
GPIO
Disabled
PTE7
M20
109
VDD33
GPIO
ALT3
RCON0
Input
Disabled
PTE8
M19
110
VDD33
GPIO
ALT3
RCON1
Input
Disabled
PTE9
M17
111
VDD33
GPIO
ALT3
RCON2
Input
Disabled
PTE10
M16
112
VDD33
GPIO
ALT3
RCON3
Input
Disabled
PTE11
L16
113
VDD33
GPIO
ALT3
RCON4
Input
Disabled
PTE12
L17
114
VDD33
GPIO
ALT3
RCON5
Input
Disabled
PTE13
Y16
78
VDD33
GPIO
ALT0
GPIO
Disabled
PTE14
W15
76
VDD33
GPIO
ALT0
GPIO
Disabled
PTE15
L18
115
VDD33
GPIO
ALT3
RCON6
Input
Disabled
PTE16
L20
116
VDD33
GPIO
ALT3
RCON7
Input
Disabled
PTE17
K20
117
VDD33
GPIO
ALT3
RCON8
Input
Disabled
PTE18
K19
118
VDD33
GPIO
ALT3
RCON9
Input
Disabled
PTE19
K18
119
VDD33
GPIO
ALT3
RCON10
Input
Disabled
PTE20
A12
170
VDD33
GPIO
ALT3
RCON11
Input
Disabled
PTE21
V16
79
VDD33
GPIO
ALT0
GPIO
Disabled
PTE22
W17
84
VDD33
GPIO
ALT0
GPIO
Disabled
PTE23
J17
122
VDD33
GPIO
ALT3
RCON12
Input
Disabled
PTE24
D19
134
VDD33
GPIO
ALT3
RCON13
Input
Disabled
PTE25
C19
135
VDD33
GPIO
ALT3
RCON14
Input
Disabled
PTE26
C20
137
VDD33
GPIO
ALT3
RCON15
Input
Disabled
PTE27
B20
138
VDD33
GPIO
ALT3
RCON16
Input
Disabled
PTE28
K16
120
VDD33
GPIO
ALT3
RCON17
Input
Disabled
RESETB/
RESET_OU
T
T4
28
VDD33
GPIO
—
RESETB/
—
RESET_OU
T
—
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
119
Functional Assignment Pins
Table 81. Functional Assignment Pins
(continued)
Signal
Name
364 MAP
BGA
176 LQFP
(R-series
ONLY)
Power
Group
TEST
T3
27
VDD33
USB0_DM
T9
62
USB0_DP
T10
USB0_VBU
S
Pad Type
GPIO
Default
Mode
(Reset)
Default
Function
Input/
Output
Value
—
TEST
—
—
USB_DCAP Analog
—
USB0_DM
—
—
63
USB_DCAP Analog
—
USB0_DP
—
—
W11
60
USB_DCAP Analog
—
USB0_VBU —
S
—
USB0_VBU
S_ DETECT
Y11
64
USB_DCAP Analog
—
USB0_VBU —
S_ DETECT
—
USB1_DM
V9
—
USB_DCAP Analog
—
USB1_DM
—
—
USB1_DP
W9
—
USB_DCAP Analog
—
USB1_DP
—
—
USB1_VBU
S
W10
—
USB_DCAP Analog
—
USB1_VBU —
S
—
USB1_VBU
S_ DETECT
U9
—
USB_DCAP Analog
—
USB1_VBU —
S_ DETECT
—
VADCSE0
Y4
35
VDDA33_A Analog
DC /
VDD12_AF
E/
VADC_AFE
_BANDGAP
?
—
VADCSE0
—
—
VADCSE1
U4
37
VDDA33_A Analog
DC /
VDD12_AF
E/
VADC_AFE
_BANDGAP
?
—
VADCSE1
—
—
VADCSE2
W4
—
VDDA33_A Analog
DC /
VDD12_AF
E/
VADC_AFE
_BANDGAP
?
—
VADCSE2
—
—
VADCSE3
V5
—
VDDA33_A Analog
DC /
VDD12_AF
E/
VADC_AFE
_BANDGAP
?
—
VADCSE3
—
—
XTAL
W13
72
DECAP_V1 Analog
1_
LDO_OUT
—
XTAL
—
—
XTAL32
W12
71
DECAP_V1 Analog
1_
LDO_OUT
—
XTAL32
—
—
VF3xxR, VF5xxR, Rev7, 11/2014.
120
Freescale Semiconductor, Inc.
Revision History
15 Revision History
The following table provides a revision history for this document.
Table 82. Revision History
Rev. No.
Date
Substantial Changes
Rev1
12/2011
Initial release
Rev2
02/2012
Updated feature list
Updated VREG electrical specifications
Updated LDO_1P1, LDO2P5 tables
Updated DDR IO parameters
Added DDR memory controller
parameters
Updated Power sequencing table
Added Power supply diagram
Updated Recommended operating
conditions
Replaced DryIce Tamper Electrical
Specifications with Voltage and
temperature monitor electrical
specifications
Updated VideoADC electricals. Updated
VideoADC supply scheme diagram.
Added VideoADC supply_decoupling
diagram
Added QuadSPI DDR mode electrical
specifications
Updated Fast internal RC oscillator table
Updated Slow internal RC oscillator
table
Updated Pinouts section
Rev3
04/2012
Updated device name throughout the
document
Minor editorial updates in the feature list
Updated VREG electrical specifications
Updated LDO electrical specifications
Updated Power consumption operating
behaviors table
Added USB PHY Current Consumption
table
Updated GPIO parameters
Updated DDR parameters
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
121
Revision History
Table 82. Revision History (continued)
Rev. No.
Date
Substantial Changes
Updated Power sequencing
Updated Power supply figure
Updated Recommended operating
conditions table
Removed Reset specifications
Updated 12-bit DAC operating
requirements
Added a note in 12-bit ADC operating
conditions section
Updated VideoADC Specifications table
Updated LCD driver specifications table
QuadSPI timing- Replaced VDDE with
VDD33
Added notes in DDR3 Timing
Parameters and LPDD2 Timing
Parameters sections.
Updated 24MHz external oscillator
electrical characteristics table
Updated OSC32K Main Characteristics
table
Updated Freescale Document Number
for 144-pin LQFP
Changed pin-name from EXT_POR to
TEST2, VBAT to VBB
Updated Pinouts section
Updated GPIO Mapping
Rev4
08/2012
Updated Part identification
Editorial changes in USB PHY Current
Consumption in Normal Mode, GPIO AC
Electrical Characteristics (3.3V power
mode)
Updated Power sequencing table
Updated Power supply diagram
Updated AC electrical specification of
following modules: DCU, 12-bit DAC,
Ethernet, Enhanced Serial Audio
Interface (ESAI), SAI/I2S, Flexbus, MLB,
DSPI, 24MHz External Oscillator, JTAG,
Debug, ESAI, QSPI
Updated Thermal Attributes for 364
MAPBGA
Updated Freescale document number
for 176-pin LQFP and 364 MAPBGA
Updated VREG specifications
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
122
Freescale Semiconductor, Inc.
Revision History
Table 82. Revision History (continued)
Rev. No.
Date
Substantial Changes
Added WBREG specifications
Updated Recommended operating
conditions table
Updated DAC INL and DNL charts
Updated Pinouts
Rev 5
April 2013
• Removed references to VF1xxR
and refernces to F100 and 144
LQFP and 256 MAPBGA
• Replaced references to Auto and
IMM by R-series and F-series
respectively
• In the feature list, the ARM Core
frequency changed to 500 MHz for
F-series
• In the feature list, changed the
DRAM controller frequency
• Updated Part Nummbering format
• Clarified the Fields table as per
Marketing
• Sample numbers updated
• From the VREG electrical
specifications tables, deleted pretrimming rows and comments
• .In the HPREG electrical
characteristics table, add footnote
on maximum Output Current
Capacity
• In the ULPREG electrical
characteristics table, clarified max
value of Output voltage @ no load
and min value of Output voltage @
full load
• In the WBREG electrical
characteristics table, clarified max
value of Output voltage @ no load
and min value of Output voltage @
full load
• In the LVD electrical specifications
table, added typ. values of Upper
voltage threshold (value @27oC)
and Lower voltage threshold
(value @27oC)
• In the LVD DIG electrical
specifications table, removed
pretrimming values and clarified
other values
• Updated LVD DIG electrical
specifications values
• Updated LDO_1P1 tables
• Updated LDO_2P5 table
• Updated Power consumption
operating behaviors tables
• Updated Absolute maximum
ratings table
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
123
Revision History
Table 82. Revision History (continued)
Rev. No.
Date
Substantial Changes
• Removed Temperature Voltage
Monitor section to security RM
• Updated VideoADC Specifications
table
Rev 5
April 2013
Updated pin muxing table with the
following changes:
• Added MII0 including M
AC0.TXDATA[2],
MAC0.TXDATA[3],
MAC0.RXDATA[2],
MAC0.RXDATA[3] ,
MAC0.TXERR, MAC0.TXCLK,
MAC0.RXCLK, MAC0.COL,
MAC0.CRS
• Following signals muxed on same
RMII0 Pins : MII0_MDC,
MII0_MDC, MII0_RXD[1],
MII0_RXD[0], MII0_RXER,
MII0_TXD[1], MII0_TXD[0],
MII0_TXEN
• Replaced FB_ALE with
FB_MUXED_ALE, FB_CS4_b with
FB_MUXED_TSIZ0, FB_TSIZ1
with FB_MUXED_TSIZ1,
FB_TBST_b with
FB_MUXED_TBST_b, FB_BE0_b
with FB_MUXED_BE0_b
• Removed RCON18,19,20
• Replaced ESAI_SDO2 with
ESAI_SDO2/ESAI_SDI3 Replaced
ESAI_SDO3 with ESAI_SDO3/
ESAI_SDI2 Replaced ESAI_SDI0
with ESAI_SDO5/ESAI_SDI0
Replaced ESAI_SDI1 with
ESAU_SDO4/ESAI_SDI1
• CKO1 additionally muxed at
PAD40
Rev 5
May 2013
In the Features, minor editorial updates
Added Part Number Format figure
Updated the Fields table as per the
device part numbers
Added Part Numbers table
Added External NPN Ballast section
In the LVD Dig Electrical Specs,
minimum value of Upper Voltage
Threshold and Lower Voltage threshold
In the FlexBus timing specifications
table, clarified the Frequency of
operation
In the Power consumption, filled TBDs.
Updated footnotes
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
124
Freescale Semiconductor, Inc.
Revision History
Table 82. Revision History (continued)
Rev. No.
Date
Substantial Changes
Rewritten the EMC radiated emissions
operating behaviors table
In the GPIO DC Electrical characteristics
table:
• Vhys test condition changed
• Added R_Keeper row
In the DDR operating conditions,
changed the Vddi Min and Max values
In the Power sequencing table,
rremoved some rows
In the Power Supply section, removed
LVDS and removed the note
In the Recommended operating
conditions table, updated min and max
of VDD12_AFE and FA_VDD. Updated
Min, Max, and Typ for VDD
Added the Recommended Connections
for Unused Analog Interfaces table
In the 12-bit ADC Characteristics table,
updated the typ and max values of TUE,
DNL. INL, ZSE, FSE
Added Receive and Transmit signal
timing specifications for MII interfaces
In the DSPI table, clarified the TBDs
In PLL 4, PLL 5, PLL 6 electrical
characteristics tables, added footnotes
In the JTAG electrical table, clarified the
TBDs
In the pinouts section, added Special
Signal table
Added Power Supply pins section
Added Functional Assignment section
Rev 6
Jan 2014
• Added QuadSPI electricals
• Changed VBB references to VBAT
• In the feature list, clarified that
ECC supported for 8-bit mode
only, not 16-bit.
• Revised the part number format
• Revised the field table
• Added Absolute Maximum Rating
table, which was madde non_cust
in the previous version
• In the Power Consumption
Operating Behavior table, Revised
min and max value of IDD_LPS3
and IDD_LPS2. Removed
IDD_LPS1 row
Table continues on the next page...
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
125
Revision History
Table 82. Revision History (continued)
Rev. No.
Date
Substantial Changes
• In the USB PHY Current
Consumption table, removed the
Normal Mode
• In the Power Sequence table,
revised the Power UP/ Down
Order column for USB0_VBUs and
USB1_VBUS
• In the Recommended operating
conditions table, revised the min
value of VBAT. Revised the min
value of VREFH_ADC Revised the
min and max values of
SDRAMC_VDD1P5
• In the Recommended Connections
for Unused Analog Interfaces
section, added the notes. Revised
the Recommendation if Unused
column
• In the 12-bit ADC operating
conditions, revised Conditions for
Ground voltage. Revised min Ref
High Voltage
• In the 12-bit DAC operating
requirements, revised the min and
max value of VREFH_ADC
• In the SDHC switching
specifications, revised the max
value of SD6
• In the 24MHz external oscillator
electrical characteristics table,
revised the min value of VIH and
max value of VIL
Rev 7
November 2014
• Updated list of security features on
page 1.
• In "Part number format" figure,
updated explanation for '1'.
• In "Fields" table, updated definition
of 'R'.
• In "Part Numbers" table, added
parts SVF331R3K1CKU2,
SVF531R3K1CMK4, and
SVF532R2K1CMK4.
• In "External NPN ballast" section,
updated recommendations for
transistor selection.
• In "DDR parameters" section,
updated table footnotes regarding
typical condition.
• In "Power sequencing" table,
added comment regarding
SDRAMC_VDD1P5: "In case the
Ballast transistor’s collector is
connected to the 1.5 V DRAM
supply (instead of the 3.3 V
VF3xxR, VF5xxR, Rev7, 11/2014.
126
Freescale Semiconductor, Inc.
Revision History
Table 82. Revision History
Rev. No.
Date
Substantial Changes
•
•
•
•
•
•
•
supply), turn this 1.5 V supply on
before turning on the 3.3V."
In "VideoADC specifications" table,
added supply current values.
In "Receive and Transmit signal
timing specifications," added the
following note: "See the most
current errata document when
using the internally generated
RXCLK and TXCLK clocks."
Updated "QuadSPI timing" section,
presenting data based on a
negative edge data launch from
the device and a negative edge
data capture; updated the figure,
"QuadSPI Input/Read timing (SDR
mode)"; updated the table,
"QuadSPI Input/Read timing (SDR
mode)."
For the "SDHC switching
specifcations" table, added the
statement, "A load of 50 pF is
assumed"; updated max value for
SD6, SDHC output delay (output
valid).
In the "24 MHz oscillator
specifications" section, added the
statement, "The crystal must be
rated for a drive level of 250 μW or
higher. An ESR (equivalent series
resistance) of 80 Ω or less is
recommended to achieve a gain
margin of 5."
In "Pinouts" section, for the
176LQFP package, added
information about exposed pad on
the bottom side.
In "Special Signal Considerations"
table, added that a "fundamentalmode" crystal should be
connected between XTAL and
EXTAL; updated maximum drive
level of crystal rating to 250 μW.
VF3xxR, VF5xxR, Rev7, 11/2014.
Freescale Semiconductor, Inc.
127
How to Reach Us:
Home Page:
freescale.com
Web Support:
freescale.com/support
Information in this document is provided solely to enable system and
software implementers to use Freescale products. There are no express
or implied copyright licenses granted hereunder to design or fabricate
any integrated circuits based on the information in this document.
Freescale reserves the right to make changes without further notice to
any products herein.
Freescale makes no warranty, representation, or guarantee regarding
the suitability of its products for any particular purpose, nor does
Freescale assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability,
including without limitation consequential or incidental damages.
“Typical” parameters that may be provided in Freescale data sheets
and/or specifications can and do vary in different applications, and
actual performance may vary over time. All operating parameters,
including “typicals,” must be validated for each customer application by
customer's technical experts. Freescale does not convey any license
under its patent rights nor the rights of others. Freescale sells products
pursuant to standard terms and conditions of sale, which can be found
at the following address: freescale.com/SalesTermsandConditions.
Freescale and the Freescale logo are trademarks of Freescale
Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. Vybrid is a trademark of
Freescale Semiconductor, Inc. All other product or service names are
the property of their respective owners. ARM and Cortex are registered
trademarks of ARM Limited. NEON is the trademark of ARM Limited.
© 2012–2013 Freescale Semiconductor, Inc.
Document Number VYBRIDRSERIESEC
Revision 7, 11/2014