A Product Line of Diodes Incorporated APR34309C SECONDARY SIDE SYNCHRONOUS RECTIFICATION SWITCHER Description Pin Assignments NEW PRODUCT APR34309C is a secondary side Combo IC, which combines an NChannel MOSFET and a driver circuit designed for synchronous rectification (SR) in DCM operation. It also integrates output voltage detect function for primary side control system. (Top View) The N-Channel MOSFET has been optimized for low gate charge, low RDS(ON), fast switching speed and body diode reverse recovery performance. The synchronous rectification can effectively reduce the secondary side rectifier power dissipation and provide high performance solution. By sensing MOSFET drain-to-source voltage, APR34309C can output ideal drive signal with less external components. It can provide high performance solution for 5V output voltage application. Same as AP4341, APR34309C detects the output voltage and provides a periodical signal when the output voltage is lower than a certain threshold. By fast response to secondary side voltage, APR34309C can effectively improve the transient performance of primary side control system. 1 8 GND VDET 2 7 GND AREF 3 6 GND VCC 4 5 DRAIN Note: The DRAIN pin of internal MOSFET is exposed PAD, which is at the bottom of IC (the dashed box). The secondary current should flow from GND(pin 6,7,8) to this exposed PAD. SO-8EP Applications The APR34309C is available in SO-8EP package. • Features • Synchronous Rectification for DCM Operation Flyback • Eliminate Resonant Ring Interference • Fast Detector of Supply Voltages • Fewest External Components DRISR • Adapters/Chargers for Cell/Cordless Phones, ADSL Modems, MP3 and Other Portable Apparatus Standby and Auxiliary Power Supplies Totally Lead-free & Fully RoHS Compliant (Notes 1 & 2) Halogen and Antimony Free. “Green” Device (Note 3) Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant. 2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and Lead-free. 3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and <1000ppm antimony compounds. Typical Applications Circuit C21 + C23 C22 + R21 APR34309C R23 CAREF DRAIN DRAIN GND DRISR GND VDET GND AREF VCC R24 C24 RAREF APR34309C Document number: DS37492 Rev. 5 - 2 1 of 13 www.diodes.com June 2015 © Diodes Incorporated A Product Line of Diodes Incorporated APR34309C NEW PRODUCT Pin Descriptions Pin Number Pin Name Function 1 DRISR Synchronous rectification MOSFET drive. 2 VDET Synchronous rectification sense input and dynamic function output, connected to DRAIN through a resistor. 3 AREF Program a voltage reference with a resistor from AREF to GND, to enable synchronous rectification MOSFET drive signal. 4 VCC Power supply, connected with system output. 5 DRAIN 6,7,8 GND Exposed PAD DRAIN Drain pin of internal MOSFET. The Drain voltage signal can obtain from this pin. Source pin of internal MOSFET, connected to Ground. Drain pin of internal MOSFET. The secondary current should flow from GND (pin 6.7.8) to this DRAIN pad. Functional Block Diagram VCC 4 VREF VDET Integrator (VDET-VCC)*tONP IOVP Dynamic OVP IAREF tONPDET AREF DRISR Counter 3 OSC 1 SRDRIVER 6,7,8 DRAIN GND 5, EP 2 VDET APR34309C Document number: DS37492 Rev. 5 - 2 2 of 13 www.diodes.com June 2015 © Diodes Incorporated A Product Line of Diodes Incorporated APR34309C Absolute Maximum Ratings (Note 4) Symbol NEW PRODUCT VCC Notes: Parameter Supply Voltage Value Unit -0.3 to 7.5 V VDET, VDRAIN Voltage at VDET, DRAIN Pin -2 to 50 V VAREF, VDRISR Voltage at AREF, DRISR Pin -0.3 to 6 V ID Continuous Drain Current 20 A IDM Pulsed Drain Current 80 A PD Power Dissipation at TA=+25ºC 2.2 W θJA Thermal Resistance (Junction to Ambient) (Note 5) 56 ºC/W θJC Thermal Resistance (Junction to Case) (Note 5) 12 ºC/W TJ Operating Junction Temperature +150 ºC -65 to +150 ºC TSTG Storage Temperature TLEAD Lead Temperature (Soldering, 10 sec) +300 ºC ESD Charge Device Model 1000 V 4. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “Recommended Operating Conditions” is not implied. Exposure to “Absolute Maximum Ratings” for extended periods may affect device reliability. 5. FR-4 substrate PC board, 2oz copper, with 1 inch2 pad layout. Recommended Operating Conditions Symbol Parameter Min Max Unit VCC Supply Voltage 3.3 6 V TA Ambient Temperature -40 +85 ºC APR34309C Document number: DS37492 Rev. 5 - 2 3 of 13 www.diodes.com June 2015 © Diodes Incorporated A Product Line of Diodes Incorporated APR34309C Electrical Characteristics Symbol (@TA = +25°C, VCC=5V, unless otherwise specified.) Parameter Conditions Min Typ Max Unit Supply Voltage ( VCC Pin ) Startup Current VCC=VSTARTUP-0.1V – 100 150 μA Operating Current VDET pin floating VCC=VTRIGGER+20mV 40 100 150 μA Startup Voltage – 2.6 3.1 3.4 V UVLO – 2.3 2.8 3.1 V Internal Trigger Voltage – 5.1 5.15 5.2 V Duty Cycle – 4 15 18 % Oscillation Period VCC=5V 18 30 37.5 μs Internal Trigger Current VCC=VTRIGGER, VCC/VDET pin is separately connected to a 20Ω resistor 30 60 80 mA tDIS Minimum Period – 18 30 37.5 ms VDIS Discharge Voltage – 5.13 5.3 5.38 V IDIS Discharge Current VCC=VDIS+0.1V 1.5 3 4.5 mA Trigger Discharger Gap – 30 110 – mV Overshoot Voltage for Discharge – 5.64 5.74 5.84 V Overshoot Current for Discharge VCC=VOVP+0.1V, VCC pin is connected to a 20Ω resistor 40 – 100 mA ISTARTUP IOP NEW PRODUCT VSTARTUP – Dynamic Output Section/Oscillator Section VTRIGGER – tOSC ITRIGGER VDIS-VTRIGGER VOVP IOVP Synchronous Voltage Detect VTHON Gate Turn-on Threshold – 0 – 1 V VTHOFF Gate Turn-off Threshold – -13 -9 -5 mV tDON Turn-on Delay Time From VTHON to VDRISR=1V – 70 130 ns tDOFF Turn-off Propagation Delay Time From VTHOFF to VDRISR=3V – 100 150 ns tRG Gate Turn-on Rising Time From 1V to 3V, CL=4.7nF – 50 100 ns tFG Gate Turn-off Falling Time From 3V to 1V, CL=4.7nF – 50 100 ns (VDET-VCC)*tONP = 25Vµs 0.9 1.8 2.7 (VDET-VCC)*tONP = 50Vµs – – 6.5 3.7 – – V tLEB_S Minimum On Time tLEB_L VDRISR_HIGH VS_MIN tOVP_LAST Kqs Notes: μs Drive Output Voltage VCC=5V SR Minimum Operating Voltage (Note 6) – – – 4.5 V Added OVP Discharge Time – – 2.0 – ms (Note 7) (VDET-VCC)*tONP = 25Vµs 0.325 – 0.515 mA*μs 6. This item specifies the minimum SR operating voltage of VIN_DC, VIN_DC≥NPS*VS_MIN. 7. This item is used to specify the value of RAREF. APR34309C Document number: DS37492 Rev. 5 - 2 4 of 13 www.diodes.com June 2015 © Diodes Incorporated A Product Line of Diodes Incorporated APR34309C Electrical Characteristics (@TA =+25°C, unless otherwise specified. Cont.) MOSFET Static Characteristics NEW PRODUCT Parameters Symbol Conditions Min Typ Max Unit Drain to Source Breakdown Voltage VDSS(BR) VGS=0V, ID=0.25mA 50 – 100 V Gate Threshold Voltage VGS(TH) VDS=VGS, ID=0.25mA 0.7 1.3 2 V Zero Gate Voltage Drain Current IDSS VDS=50V, VGS=0V – – 1 µA Gate to Source Leakage Current IGSS VGS=10V, VDS=0V – – ±100 nA Drain to Source On-state Resistance RDS(ON) VGS=4.5V, ID=3A – 8 – mΩ Min Typ Max Unit – 1872 – – 506 – – 43 – – 3.1 – – 4.8 – MOSFET Dynamic Characteristics Parameters Symbol Conditions Input Capacitance Ciss Output Capacitance Coss Reverse Transfer Capacitance Crss Gate to Source Charge Qgs Gate to Drain Charge (Miller Charger) Qgd Total Gate Charge Qg VGS=4.5V – 15 – Gate Resistance Rg – – 1.8 – APR34309C Document number: DS37492 Rev. 5 - 2 VGS=0V, VDS=25V, f=1MHz VGS=0V to 10V, VDD=25V, ID=15A 5 of 13 www.diodes.com pF nC Ω June 2015 © Diodes Incorporated A Product Line of Diodes Incorporated APR34309C Performance Characteristics Startup Voltage vs. Temperature UVLO vs. Temperature 3.5 3.50 3.00 UVLO (V) Startup Voltage (V) 3.0 2.75 2.5 2.0 2.50 1.5 2.25 2.00 -40 -20 0 20 40 60 80 100 120 1.0 -40 140 -20 0 20 Internal Trigger Voltage vs. Temperature 80 100 120 140 Internal Trigger Current vs. Temperature 80 5.4 70 Internal Trigger Current (mA) 5.3 Internal Trigger Voltage (V) 60 Temperature ( C) Temperature ( C) 5.2 5.1 5.0 4.9 4.8 4.7 -40 40 o o 60 50 40 30 20 10 -20 0 20 40 60 80 100 120 0 -40 140 -20 0 20 40 60 80 100 120 140 o o Temperature ( C) Temperature ( C) Overshoot Voltage for Discharge vs. Temperature Overshoot Current for Discharge vs. Temperature 160 Overshoot Current for Discharge (mA) 6.0 Overshoot Voltage for Discharge (V) NEW PRODUCT 3.25 5.8 5.6 5.4 5.2 140 120 100 80 60 40 20 5.0 -40 -20 0 20 40 60 80 100 120 0 -40 140 Document number: DS37492 Rev. 5 - 2 0 20 40 60 80 100 120 140 o Temperature ( C) APR34309C -20 Temperature ( C) o 6 of 13 www.diodes.com June 2015 © Diodes Incorporated A Product Line of Diodes Incorporated APR34309C Performance Characteristics (Cont.) Gate Turn Off Threshold vs. Temperature Kqs (See Note 7) vs. Temperature 0.7 0 0.5 Kqs (mA*s) Gate Turn Off Threshold (mV) -10 -20 0.4 0.3 0.2 -30 0.1 -40 -40 -20 0 20 40 60 80 100 120 0.0 -40 140 -20 0 20 60 80 100 120 140 Temperature ( C) Temperature ( C) Operating Current vs. Temperature Drain to Source On-state Resistance vs. Temperature 20 Drain to Source On-state Resistance (m) 140 120 100 80 60 40 20 0 -40 40 o o Operating Current (A) NEW PRODUCT 0.6 -20 0 20 40 60 80 100 120 140 14 12 10 8 6 4 2 0 -40 -20 0 20 40 60 80 100 120 140 Temperature ( C) Temperature ( C) Document number: DS37492 Rev. 5 - 2 16 o o APR34309C 18 7 of 13 www.diodes.com June 2015 © Diodes Incorporated A Product Line of Diodes Incorporated APR34309C Output Voltage Detect Function Description tOSC tDIS tDIS tDIS tDIS tDIS tDIS tOSC VDET VOVP VDIS NEW PRODUCT VDIS VTRIGGER VCC VTRIGGER VON UVLO IOVP IVCC VOFF tOVP_LAST IDIS Figure 1. Typical Waveforms of APR34309C When VCC is beyond power-on voltage (VON), the APR34309C starts up. The VDET pin asserts a periodical pulse and the oscillation period is tOSC. When VCC is beyond the trigger voltage (VTRIGGER), the periodical pulse at VDET pin is discontinued. When VCC is beyond the discharge voltage (VDIS), the discharge circuit will be enabled, and a 3mA current (IDIS) will flow into VCC pin. When VCC is higher than the overshoot voltage (VOVP), the APR34309C will enable a discharge circuit, the discharge current (IOVP) will last tOVP_LAST time. After the tOVP_LAST time, APR34309C will stop the discharge current and detect VCC voltage again. If VCC is still higher than VOVP, the tOVP_LAST time discharge current will be enabled again. Once the OVP discharge current is asserted, the periodical pulse at VDET pin will be disabled. When the VCC falls below the power-off voltage (VOFF), the APR34309C will shut down. Operation Description MOSFET Driver The operation of the SR is described with timing diagram shown in Figure 2. APR34309C monitors the MOSFET drain-source voltage. When the drain voltage is lower than the turn-on threshold voltage VTHON, the IC outputs a positive drive voltage after a turn-on delay time (tDON). The MOSFET will turn on and the current will transfer from the body diode into the MOSFET’s channel. In the process of drain current decreasing linearly toward zero, the drain-source voltage rises synchronically. When it rises over the turn off threshold voltage VTHOFF, APR34309C pulls the drive signal down after a turn-off delay (tDOFF). I,V VDET IS VTHON 0 t VTHOFF VDRISR 0.9VDRISR 0.9VDRISR 0.1VDRISR 0 tDON tRG tDOFF 0.1VDRISR t t FG Figure 2. Typical Waveforms of APR34309C APR34309C Document number: DS37492 Rev. 5 - 2 8 of 13 www.diodes.com June 2015 © Diodes Incorporated A Product Line of Diodes Incorporated APR34309C Operation Description (Cont.) Minimum On Time When the controlled MOSFET gate is turned on, some ringing noise is generated. The minimum on-time timer blanks the VTHOFF comparator, keeping the controlled MOSFET on for at least the minimum on time. If V THOFF falls below the threshold before minimum on time expires, the MOSFET will keep on until the end of the minimum on time. The minimum on time is in direct proportion to the (VDET-VCC)*tONP. When (VDET-VCC)*tONP=5V*5μs, the minimum on time is about 1.8μs. NEW PRODUCT The Value and Meaning of AREF Resistor As to DCM operation Flyback converter, after secondary rectifier stops conduction the primary MOSFET Drain-to-source ringing waveform is resulted from the resonant of primary inductance and equivalent switch device output capacitance. This ringing waveform probably leads to Synchronous Rectifier error conduction. To avoid this fault happening, APR34309C has a special function design by means of volt-second product detecting. From the sensed voltage of VDET pin to see, the volt-second product of voltage above VCC at primary switch on time is much higher than the volt-second product of each cycle ringing voltage above VCC. Therefore, before every time Synchronous Rectifier turning on, APR34309C judges if the detected volt-second product of VDET voltage above VCC is higher than a threshold and then turn on synchronous Rectifier. The purpose of AREF resistor is to determine the volt-second product threshold. APR34309C has a parameter, Kqs, which converts RAREF value to volt-second product, Area2 R AREF * Kqs In general, Area1 and Area3, the value of which should be test on system, depend on system design and are always fixed after system design frozen. As to BCD PSR design, the Area1 value changes with primary peak current value and Area3 value generally keeps constant at all of conditions. So the AREF resistor design should consider the worst case, the minimum primary peak current condition. Since of system design parameter distribution, Area1 and Area3 have moderate tolerance. So Area2 should be designed between the middle of Area1 and Area3 to keep enough design margin. Area3 R AREF * Kqs Area1 Area1=(VDET-VCC)*tONP Area3 VDET VCC Area2=Kqs*RAREF Figure 3. AREF Function SR Minimum Operating Voltage APR34309C sets a minimum SR operating voltage by comparing the difference between V DET and output voltage (VCC). The value of VDET–VCC must be higher than its internal reference, then APR34309C will begin to integrate the area of (VDET–VCC)*tONP. If not, the area integrating will not begin and the SR driver will be disabled. SR Turning off Timing Impact on PSR CV Sampling As to synchronous rectification on Flyback power system, SR MOSFET need to turn off in advance of secondary side current decreasing to zero to avoid current flowing reversely. When SR turns off in advance, the secondary current will flow through the body diode. The SR turning off time is determined by the VTHOFF at a fixed system. When VTHOFF is more close to zero, the SR turning on time gets longer and body diode conduction time gets shorter. Since of the different voltage drop between SR MOSFET and body diode, the PSR feedback signal VFB appears a voltage jump at the time of SR MOSFET turning off. If the PSR CV sampling time tSAMPLE is close to even behind this voltage jump time, there will be system unstable operation issue or the lower output voltage issue. APR34309C Document number: DS37492 Rev. 5 - 2 9 of 13 www.diodes.com June 2015 © Diodes Incorporated A Product Line of Diodes Incorporated APR34309C Operation Description (Cont.) To ensure system operating stable, it must be met: tBODYDIODE<tONS*(1- tSAMPLE) tSAMPLE SR Turnoff, Bodydiode operating NEW PRODUCT SR Operating tBODYDIODE VFB tONS Figure 4. SR Turning off Timing Impact on PSR CV Sampling Recommended Application Circuit Parameters The two resistors R23 and R24 are used to pass ESD test. The value of R23 and R24 should be over 20Ω and below 47Ω respectively because of the undershoot performance. The package of R23 and R24 should be at least 0805 and there isn’t any trace under these two resistors. CAREF is suggested to parallel with AREF resistor to keep the volt-second product threshold stable. And the recommended value of CAREF is 100nF. The recommended value of C24 is 100nF. Ordering Information APR34309C XX XX - XX Product Name Package Temperature Range SO-8EP -40 to +85C APR34309C Document number: DS37492 Rev. 5 - 2 Package Packing RoHS/Green MP: SO-8EP TR : Tape & Reel G1 : Green Part Number APR34309CMPTR-G1 10 of 13 www.diodes.com Marking ID 34309CMP-G1 Packing 4000/Tape & Reel June 2015 © Diodes Incorporated A Product Line of Diodes Incorporated APR34309C Marking Information First and Second Lines: Logo and Marking ID Third Line: Date Code Y: Year WW: Work Week of Molding A: Assembly House Code th th XX: 7 and 8 Digits of Batch No. 34309C MP-G1 YWWAXX - Package Outline Dimensions (All dimensions in mm(inch).) (1) Package Type: SO-8EP 3.800(0.150) 4.000(0.157) 2.110(0.083) 2.710(0.107) 2.750(0.108) 3.402(0.134) NEW PRODUCT (Top View) 1.270(0.050) TYP 4.700(0.185) 5.100(0.201) 0.300(0.012) 0.510(0.020) 5.800(0.228) 6.200(0.244) 0.050(0.002) 0.150(0.006) 1.350(0.053) 1.550(0.061) 0° 8° 0.400(0.016) 1.270(0.050) 0.150(0.006) 0.250(0.010) Note: Eject hole, oriented hole and mold mark is optional. APR34309C Document number: DS37492 Rev. 5 - 2 11 of 13 www.diodes.com June 2015 © Diodes Incorporated A Product Line of Diodes Incorporated APR34309C Suggested Pad Layout Package Type: SO-8EP NEW PRODUCT (1) Y1 G Z X1 Y E X Dimensions Z (mm)/(inch) G (mm)/(inch) X (mm)/(inch) Y (mm)/(inch) X1 (mm)/(inch) Y1 (mm)/(inch) E (mm)/(inch) Value 6.900/0.272 3.900/0.154 0.650/0.026 1.500/0.059 3.600/0.142 2.700/0.106 1.270/0.050 APR34309C Document number: DS37492 Rev. 5 - 2 12 of 13 www.diodes.com June 2015 © Diodes Incorporated A Product Line of Diodes Incorporated APR34309C IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). NEW PRODUCT Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks. This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the final and determinative format released by Diodes Incorporated. LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user. B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2015, Diodes Incorporated www.diodes.com APR34309C Document number: DS37492 Rev. 5 - 2 13 of 13 www.diodes.com June 2015 © Diodes Incorporated