NCV59748 D

NCV59748
1.5 A, Dual-Rail Very
Low‐Dropout Linear
Regulator with
Programmable Soft‐Start
The NCV59748 is dual−rail very low dropout voltage regulator,
capable of providing an output current in excess of 1.5 A with a
dropout voltage of 60 mV typ. at full load current. The devices are
stable with ceramic and any other type of output capacitor ≥ 2.2 mF.
This series contains adjustable output voltage version with output
voltage down to 0.8 V. Internal protection features consist of built-in
thermal shutdown and output current limiting protection.
User-programmable Soft-Start and Power-Good pins are available.
The NCV59748 is offered in DFN10 3×3 package, wettable flanks
option available for Enhanced Optical Inspection.
www.onsemi.com
DFN10
CASE 485C
MARKING DIAGRAM
1
Features
•
•
•
•
•
•
•
•
•
•
•
•
Output Current in Excess of 1.5 A
VIN Range: 0.8 V to 5.5 V
VBIAS Range: 2.7 V to 5.5 V
Output Voltage Range: 0.8 V to 3.6 V
Dropout Voltage: 60 mV at 1.5 A
Programmable Soft-Start
Open Drain Power Good Output
Fast Transient Response
Stable with Any Type of Output Capacitor ≥ 2.2 mF
Current Limit and Thermal Shutdown Protection
NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These are Pb−Free Devices
A
L
Y
W
G
NCV
59748
ALYWG
G
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb-Free Package
(Note: Microdot may be in either location)
PIN CONNECTIONS
IN
1
10
OUT
IN
2
9
OUT
PG
BIAS
EN
3
8
FB
SS
GND
4
5
Thermal
Pad
7
6
DFN10−3y3−0.5P
Applications
• Automotive, Consumer and Industrial Equipment Point of Load
•
•
Regulation
FPGA, DSP and Logic Power Supplies
Switching Power Supply Post Regulation
ORDERING INFORMATION
See detailed ordering, marking and shipping information in the
package dimensions section on page 9 of this data sheet.
NCV59748
Figure 1. Typical Application Schematic
© Semiconductor Components Industries, LLC, 2015
November, 2015 − Rev. 0
1
Publication Order Number:
NCV59748/D
NCV59748
Figure 2. Simplified Schematic Block Diagram
Table 1. PIN FUNCTION DESCRIPTION
Name
DFN10
IN
1, 2
EN
5
Enable pin. Driving this pin high enables the regulator. Driving this pin low puts the regulator into
shutdown mode. This pin must not be left floating.
SS
7
Soft-Start pin. A capacitor connected on this pin to ground sets the start-up time. If this pin is left
floating, the regulator output soft-start ramp time is typically 200 ms.
BIAS
4
Bias input voltage for error amplifier, reference, and internal control circuits.
PG
3
Power-Good (PG) is an open-drain, active-high output that indicates the status of VOUT. When VOUT
exceeds the PG trip threshold, the PG pin goes into a high-impedance state. When VOUT is below this
threshold the pin is driven to a low-impedance state. A pull-up resistor from 10 kW to 1 MW should be
connected from this pin to a supply up to 5.5 V. The supply can be higher than the input voltage.
Alternatively, the PG pin can be left floating if output monitoring is not necessary.
FB
8
This pin is the feedback connection to the center tap of an external resistor divider network that sets the
output voltage. This pin must not be left floating.
OUT
9, 10
Regulated output voltage. A small capacitor (total typical capacitance ≥ 2.2 mF, ceramic) is needed from
this pin to ground to assure stability.
GND
6
PAD/TAB
Description
Unregulated input to the device.
Ground
Should be soldered to the ground plane for increased thermal performance.
www.onsemi.com
2
NCV59748
Table 2. ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Value
Unit
Input Voltage Range
VIN
−0.3 to +6
V
Input Voltage Range
VBIAS
−0.3 to +6
V
Enable Voltage Range
VEN
−0.3 to +6
V
Power−Good Voltage Range
VPG
−0.3 to +6
V
PG Sink Current
IPG
0 to +1.5
mA
SS Pin Voltage Range
VSS
−0.3 to +6
V
Feedback Pin Voltage Range
VFB
−0.3 to +6
V
Output Voltage Range
VOUT
−0.3 to (VIN + 0.3) ≤ 6
V
Maximum Output Current
IOUT
Internally Limited
PD
See Thermal Characteristics Table and Formula
Output Short Circuit Duration
Indefinite
Continuous Total Power Dissipation
Maximum Junction Temperature
TJMAX
+125
°C
Storage Junction Temperature Range
TSTG
−55 to +150
°C
ESD Capability, Human Body Model (Note 2)
ESDHBM
2000
V
ESD Capability, Machine Model (Note 2)
ESDMM
200
V
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
2. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per AEC−Q100−002
ESD Machine Model tested per AEC−Q100−003
Latch-up Current Maximum Rating ≤150 mA per AEC−Q100−004
Table 3. THERMAL CHARACTERISTICS
Rating
Symbol
Value
Unit
RqJA
41.5
°C/W
RqJC
6.6
°C/W
Thermal Characteristics, DFN10, 3x3, 0.5P package
Thermal Resistance, Junction−to−Ambient (Note 5)
Thermal Resistance, Junction−to−Case (bottom) (Note 6)
3. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
4. Thermal data are derived by thermal simulations based on methodology specified in the JEDEC JESD51 series standards. The following
assumptions are used in the simulations:
This data was generated with only a single device at the center of a high−K (2s2p) board with 3 in x 3 in copper area which follows the
JEDEC51.7 guidelines.
− DFN10: The exposed pad is connected to the PCB ground layer through a 3x2 thermal via array. Vias are 0.3 mm diameter, plated.
− DFN10: Each of top and bottom copper layers are assumed to have thermal conductivity representing 20% copper coverage.
5. The junction−to−ambient thermal resistance under natural convection is obtained in a simulation on a high−K board, following the JEDEC51.7
guidelines with assumptions as above, in an environment described in JESD51−2a.
6. The junction−to−case (bottom) thermal resistance is obtained by simulating a cold plate test on the IC exposed pad. Test description can
be found in the ANSI SEMI standard G30−88.
Table 4. RECOMMENDED OPERATING CONDITIONS (Note 7)
Rating
Symbol
Min
Max
Unit
Input Voltage
VIN
VOUT + VDO
5.5
V
Bias Voltage
VBIAS
2.7
5.5
V
TJ
−40
125
°C
Junction Temperature
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
7. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
www.onsemi.com
3
NCV59748
Table 5. ELECTRICAL CHARACTERISTICS (At VEN = 1.1 V, VIN = VOUT + 0.3 V, CBIAS = 0.1 mF, CSS = 1 nF, CIN = COUT = 10 mF,
IOUT = 50 mA, VBIAS = 5.0 V, TJ = −40°C to +125°C, unless otherwise noted. Typical values are at TJ = +25°C.)
Symbol
VIN
Parameter
Test Conditions
Input Voltage Range
Min
Typ
Max
Unit
VOUT + VDO
−
5.5
V
2.7
−
5.5
V
−
−
1.6
0.4
−
−
V
VBIAS
Bias Pin Voltage Range
UVLO
Undervoltage Lock-out
VBIAS Rising
Hysteresis
VREF
Internal Reference (Adj.)
TJ = +25°C
0.796
0.8
0.804
V
VOUT
Output Voltage Range
VIN = 5 V, IOUT = 1.5 A
VREF
−
3.6
V
Accuracy (Note 1)
2.97 V < VBIAS < 5.5 V,
50 mA < IOUT < 1.5 A
−2
±0.5
+2
%
VOUT/VIN
Line Regulation
VOUT (NOM) + 0.3 < VIN < 5.5 V
−
0.03
−
%/V
VOUT/IOUT
Load Regulation
50 mA < IOUT < 1.5 A
−
0.09
−
%/A
VIN Dropout Voltage (Note 2)
IOUT = 1.5 A,
VBIAS − VOUT (NOM) ≥ 3.25 V (Note 3)
−
60
165
mV
VBIAS Dropout Voltage (Note 2)
IOUT = 1.5 A, VIN = VBIAS
−
1.31
1.6
V
Current Limit
VOUT = 80% × VOUT (NOM)
2.0
−
5.5
A
−
1
2
mA
−
1
50
mA
−1
0.15
1
mA
1 kHz, IOUT = 1.5 A, VIN = 1.8 V,
VOUT = 1.5 V
−
75
−
dB
300 kHz, IOUT = 1.5 A, VIN = 1.8 V,
VOUT = 1.5 V
−
30
−
1 kHz, IOUT = 1.5 A, VIN = 1.8 V,
VOUT = 1.5 V
−
75
−
300 kHz, IOUT = 1.5 A, VIN = 1.8 V,
VOUT = 1.5 V
−
30
−
VDO
ICL
IBIAS
Bias Pin Current
ISHDN
Shutdown Supply Current (IGND)
IFB
PSRR
VEN ≤ 0.4 V
Feedback Pin Current
Power-Supply Rejection
(VIN to VOUT)
Power-Supply Rejection
(VBIAS to VOUT)
dB
Noise
Output Noise Voltage
100 Hz to 100 kHz, IOUT = 1.5 A
−
25 × VOUT
−
mVrms
tSTRT
Minimum Startup Time
RLOAD for IOUT = 1.0 A, CSS = open
−
200
−
ms
Soft-Start Charging Current
VSS = 0.4 V
−
0.44
−
mA
VEN, HI
Enable Input High Level
1.1
−
5.5
V
VEN, LO
Enable Input Low Level
0
−
0.4
V
VEN, HYS
Enable Pin Hysteresis
−
50
−
mV
VEN, DG
Enable Pin Deglitch Time
−
20
−
ms
ISS
IEN
Enable Pin Current
VEN = 5 V
−
0.1
1
mA
VIT
PG Trip Threshold
VOUT Decreasing
85
90
94
%VOUT
VHYS
PG Trip Hysteresis
−
3
−
%VOUT
VPG, LO
PG Output Low Voltage
IPG = 1 mA (Sinking), VOUT < VIT
−
−
0.3
V
IPG, LKG
PG Leakage Current
VPG = 5.25 V, VOUT > VIT
−
0.1
1
mA
Thermal Shutdown Temperature
Shutdown, Temperature Increasing
Reset, Temperature Decreasing
−
−
+165
+140
−
−
°C
TSD
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
1. Adjustable devices tested at VREF; external resistor tolerance is not taken into account.
2. Dropout is defined as the voltage from the input to VOUT when VOUT is 3% below nominal.
3. 3.25 V is a test condition of this device and can be adjusted by referring to Figure 8.
www.onsemi.com
4
NCV59748
TYPICAL CHARACTERISTICS
0.20
0.5
0.15
0.4
0.10
−40°C
+125°C
0.05
0
CHANGE IN VOUT (%)
CHANGE IN VOUT (%)
At TJ = +25°C, VIN = VOUT(TYP) + 0.3 V, VBIAS = 5 V, IOUT = 50 mA, VEN = VIN,
CIN = 1 mF, CBIAS = 4.7 mF, and COUT = 10 mF, unless otherwise noted.
+25°C
−0.05
−0.10
+125°C
−40°C
0.1
0
−0.1
+25°C
−0.2
−0.4
−0.5
−0.20
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
0.5
5.0
1.0
1.5
2.0
2.5
3.0
VIN − VOUT (V)
VBIAS − VOUT (V)
Figure 3. VIN Line Regulation
Figure 4. VBIAS Line Regulation
3.5
4.0
0.5
0.5
0.4
0.4
0.3
0.3
0.2
CHANGE IN VOUT (%)
CHANGE IN VOUT (%)
0.2
−0.3
−0.15
+125°C
0.1
+25°C
0
−0.1
−0.2
−0.3
+125°C
0.2
0.1
+25°C
0
−0.1
−0.2
−0.3
−40°C
−0.4
−0.5
10
20
30
40
50
0
0.5
1.0
1.5
IOUT, OUTPUT CURRENT (mA)
IOUT, OUTPUT CURRENT (A)
Figure 5. Load Regulation
Figure 6. Load Regulation
60
50
+125°C
40
+25°C
30
−40°C
20
10
0
0
−40°C
−0.4
−0.5
VDO (VIN − VOUT) DROPOUT VOLTAGE (mV)
0
VDO (VIN − VOUT) DROPOUT VOLTAGE (mV)
0.3
0.5
1.0
1.5
200
180
IOUT = 1.5 A
160
140
120
100
80
+125°C
60
+25°C
40
−40°C
20
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
IOUT, OUTPUT CURRENT (A)
VBIAS − VOUT (V)
Figure 7. VIN Dropout Voltage vs. IOUT and
Temperature TJ
Figure 8. VIN Dropout Voltage vs. (VBIAS −
VOUT) and Temperature TJ
www.onsemi.com
5
4.5
NCV59748
TYPICAL CHARACTERISTICS
VDO (VBIAS − VOUT) DROPOUT VOLTAGE (mV)
VDO (VIN − VOUT) DROPOUT VOLTAGE (mV)
At TJ = +25°C, VIN = VOUT(TYP) + 0.3 V, VBIAS = 5 V, IOUT = 50 mA, VEN = VIN,
CIN = 1 mF, CBIAS = 4.7 mF, and COUT = 10 mF, unless otherwise noted.
200
180
IOUT = 0.5 A
160
140
−40°C
120
+25°C
100
+125°C
80
60
40
20
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
VBIAS − VOUT (V)
1200
1100
−40°C
1000
+25°C
900
+125°C
800
700
600
0
2000
2000
1800
−40°C
1000
800
600
+125°C
1200
−40°C
1000
800
600
400
400
200
200
0
0
0
0.5
1.0
2.0
1.5
2.5
3.0
3.5
4.0
4.5
5.0
IOUT, OUTPUT CURRENT (A)
VBIAS (V)
Figure 11. BIAS Pin Current vs. IOUT and
Temperature TJ
Figure 12. BIAS Pin Current vs. VBIAS and
Temperature TJ
0.500
5.5
VPG,LO, L−LEVEL PG VOLTAGE (V)
1.0
0.475
0.450
ISS (mA)
+25°C
1400
+125°C
IBIAS (mA)
IBIAS (mA)
1600
+25°C
1200
1.5
Figure 10. VBIAS Dropout Voltage vs. IOUT and
Temperature TJ
1800
1400
1.0
IOUT, OUTPUT CURRENT (A)
Figure 9. VIN Dropout Voltage vs. (VBIAS −
VOUT) and Temperature TJ
1600
0.5
0.425
0.400
0.375
0.350
0.325
0.300
−50
−25
0
25
50
75
100
125
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0
2
4
6
8
10
TJ, JUNCTION TEMPERATURE (°C)
IPG, PG PIN CURRENT (mA)
Figure 13. Soft Start Charging Current ISS vs.
Temperature TJ
Figure 14. L−level PG Voltage vs. Current
www.onsemi.com
6
12
NCV59748
TYPICAL CHARACTERISTICS
At TJ = +25°C, VIN = VOUT(TYP) + 0.3 V, VBIAS = 5 V, IOUT = 50 mA, VEN = VIN,
CIN = 1 mF, CBIAS = 4.7 mF, and COUT = 10 mF, unless otherwise noted.
4.5
−40°C
ICL, CURRENT LIMIT (A)
4.0
3.5
+25°C
+125°C
3.0
2.5
2.0
1.5
1.0
0.5
0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
VBIAS − VOUT (V)
Figure 15. Current Limit vs. (VBIAS − VOUT)
www.onsemi.com
7
5.0
NCV59748
APPLICATIONS INFORMATION
The NCV59748 dual−rail very low dropout voltage
regulator is using NMOS pass transistor for output voltage
regulation from VIN voltage. All the low current internal
controll circuitry is powered from the VBIAS voltage.
The use of an NMOS pass transistor offers several
advantages in applications. Unlike a PMOS topology
devices, the output capacitor has reduced impact on loop
stability. Vin to Vout operating voltage difference can be
very low compared with standard PMOS regulators in very
low Vin applications.
The NCV59748 offers programmable smooth monotonic
start-up. The controlled voltage rising limits the inrush
current what is advantageous in applications with large
capacitive loads. The Voltage Controlled Soft Start timing is
programmable by external Css capacitor value.
The Enable (EN) input is equipped with internal
hysteresis and deglitch filter.
Open Drain type Power Good (PG) output is available for
Vout monitoring and sequencing of other devices.
NCV59748 is a Adjustable linear regulator. The required
Output voltage can be adjusted by two external resistors.
Typical application schematics is shown in Figure 16.
greater. Ceramic or other low ESR capacitors are
recommended. For the best performance all the capacitors
should be connected to the NCV59748 respective pins
directly in the device PCB copper layer, not through vias
having not negligible impedance.
NCV59748
The Soft-Start ramp time depends on the Soft Start
charging current ISS, Soft-Start capacitor value CSS and
internal reference voltage VREF.
The Soft –Start time can be calculated using following
equations:
tss = CSS x (VREF / ISS) [s, F,V,A]
or in more practical units
tSS = CSS x 0.8V / 0.44 = CSS x 1.82
where
tss = Soft−Start time in miliseconds
CSS = Soft−Start capacitor value in nano Farads
Capacitor values for frequently used Soft-Start times can be
found in the Table 7.
The maximal recommended value of CSS capacitor is
15 nF. For higher CSS values the capacitor full discharging
before new Soft-Start cycle is not guaranteed.
V OUT + 0.8
Enable Operation
The enable pin will turn the regulator on or off. The
threshold limits are covered in the electrical characteristics
table in this data sheet. If the enable function is not to be used
then the pin should be connected to VIN or VBIAS.
Output Noise
When the NCV59748 device reaches the end of the
Soft−Start cycle, the Soft Start capacitor is switched to serve
as a Noise filtering capacitor.
Output Voltage Adjust
The output voltage can be adjusted from 0.8 V to 3.6 V
using resistors divider between the output and the FB input.
Recommended resistor values for frequently used voltages
can be found in the Table 6.
Programmable Soft−Start
ǒ1 ) R 1ńR 2Ǔ
Figure 16. Typical Application Schematics
Dropout Voltage
Because of two power supply inputs VIN and VBIAS and
one VOUT regulator output, there are two Dropout voltages
specified.
The first, the VIN Dropout voltage is the voltage
difference (VIN – VOUT) when VOUT starts to decrease by
percents specified in the Electrical Characteristics table.
VBIAS is high enough, specific value is published in the
Electrical Characteristics table.
The second, VBIAS dropout voltage is the voltage
difference (VBIAS – VOUT) when VIN and VBIAS pins are
joined together and VOUT starts to decrease.
Current Limitation
The internal Current Limitation circuitry allows the
device to supply the full nominal current and surges but
protects the device against Current Overload or Short.
Thermal Protection
Internal thermal shutdown (TSD) circuitry is provided to
protect the integrated circuit in the event that the maximum
junction temperature is exceeded. When TSD activated , the
regulator output turns off. When cooling down under the low
temperature threshold, device output is activated again. This
TSD feature is provided to prevent failures from accidental
overheating.
Input and Output Capacitors
The device is designed to be stable for all available types
and values of output capacitors ≥ 2.2 mF. The device is also
stable with multiple capacitors in parallel, which can be of
any type or value.
In applications where no low input supplies impedance
available (PCB inductance in VIN and/or VBIAS inputs as
example), the recommended CIN and CBIAS value is 1 mF or
www.onsemi.com
8
NCV59748
Table 6. RESISTOR VALUES FOR PROGRAMMING
THE OUTPUT VOLTAGE
Table 7. CAPACITOR VALUES FOR PROGRAMMING
THE SOFT−START TIME
VOUT (V)
R1 (kW)
R2 (kW)
Soft−Start Time
CSS
0.8
Short
Open
0.2 ms
Open
0.9
0.619
4.99
0.5 ms
270 pF
NOTE:
1.0
1.13
4.53
1 ms
560 pF
1.05
1.37
4.33
5 ms
2.7 nF
1.1
1.87
4.99
10 ms
5.6 nF
1.2
2.49
4.99
18 ms
10 nF
1.5
4.12
4.75
1.8
3.57
2.87
2.5
3.57
1.69
3.3
3.57
1.15
VOUT = 0.8 x (1 + R1/R2)
Resistors in the table are standard 1% types
Table 8. ORDERING INFORMATION
Output Current
Output Voltage
Marking
Package
Shipping†
NCV59748MNADJTBG
1.5 A
ADJ
NCV
59748
DFN10
(Non−Wettable Flank)
3000 / Tape & Reel
NCV59748MWADJTBG
1.5 A
ADJ
NCVW
59748
DFN10
(Wettable Flank)
3000 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
9
NCV59748
PACKAGE DIMENSIONS
DFN10, 3x3, 0.5P
CASE 485C
ISSUE D
D
A
B
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS
MEASURED BETWEEN 0.25 AND 0.30 MM FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS
THE TERMINALS.
5. TERMINAL b MAY HAVE MOLD COMPOUND MATERIAL ALONG
SIDE EDGE. MOLD FLASHING MAY NOT EXCEED 30 MICRONS
ONTO BOTTOM SURFACE OF TERMINAL b.
6. FOR DEVICE OPN CONTAINING W OPTION, DETAIL A AND B
ALTERNATE CONSTRUCTION ARE NOT APPLICABLE.
L
L1
PIN ONE
REFERENCE
0.15 C
2X
2X
ÇÇÇ
ÇÇÇ
ÇÇÇ
0.15 C
DETAIL A
ALTERNATE TERMINAL
CONSTRUCTION
E
ÉÉÉ
ÉÉÉ
ÇÇÇ
EXPOSED Cu
TOP VIEW
(A3)
DETAIL B
0.10 C
ALTERNATE
CONSTRUCTIONS
0.08 C
A1
SIDE VIEW
C
10X
1
SEATING
PLANE
MILLIMETERS
MIN
MAX
0.80
1.00
0.00
0.05
0.20 REF
0.18
0.30
3.00 BSC
2.40
2.60
3.00 BSC
1.70
1.90
0.50 BSC
0.19 TYP
0.35
0.45
0.00
0.03
SOLDERING FOOTPRINT*
D2
DETAIL A
A1
A3
DETAIL B
A
10X
ÉÉ
ÉÉ
ÇÇ
MOLD CMPD
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
L1
L
2.64
5
PACKAGE
OUTLINE
10X
0.55
E2
1.90
K
10
6
10X
e
3.30
b
BOTTOM VIEW
0.10 C A B
0.05 C
10X
0.30
0.50
PITCH
NOTE 3
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
10
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCV59748/D