NB6L14S D

NB6L14S
2.5 V 1:4 AnyLevel]
Differential Input to LVDS
Fanout Buffer/Translator
The NB6L14S is a differential 1:4 Clock or Data Receiver and will
accept AnyLevel differential input signals: LVPECL, CML, LVDS, or
HSCL. These signals will be translated to LVDS and four identical
copies of Clock or Data will be distributed, operating up to 2.0 GHz or
2.5 Gb/s, respectively. As such, the NB6L14S is ideal for SONET,
GigE, Fiber Channel, Backplane and other Clock or Data distribution
applications.
The NB6L14S has a wide input common mode range from
GND + 50 mV to VCC − 50 mV. Combined with the 50 W internal
termination resistors at the inputs, the NB6L14S is ideal for translating
a variety of differential or single−ended Clock or Data signals to
350 mV typical LVDS output levels.
The NB6L14S is the 2.5 V version of the NB6N14S and is offered in
a small 3 mm x 3 mm 16−QFN package. Application notes, models,
and support documentation are available at www.onsemi.com.
The NB6L14S is a member of the ECLinPS MAX™ family of high
performance products.
MARKING
DIAGRAM*
16
1
NB6L
14S
ALYW G
G
1
QFN−16
MN SUFFIX
CASE 485G
A
L
Y
W
G
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
(Note: Microdot may be in either location)
Features
•
•
•
•
•
•
•
•
•
http://onsemi.com
*For additional marking information, refer to
Application Note AND8002/D.
Maximum Input Clock Frequency > 2.0 GHz
Maximum Input Data Rate > 2.5 Gb/s
1 ps Maximum of RMS Clock Jitter
Typically 10 ps of Data Dependent Jitter
380 ps Typical Propagation Delay
120 ps Typical Rise and Fall Times
Single Power Supply; VCC = 2.5 $ 5%
VREF_AC Reference Output
These are Pb−Free Devices
Q0
Q0
Q1
Q1
IN
W
VT 50
W
IN 50
Q2
Q2
VOLTAGE (130 mV/div)
EN
(LVTTL/CMOS)
D
Q
Q3
VREFAC
Q3
Device DDJ = 10 ps
Figure 1. Logic Diagram
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 10 of this data sheet.
TIME (58 ps/div)
Figure 2. Typical Output Waveform at 2.488 Gb/s with
PRBS 223−1 (VINPP = 400 mV; Input Signal DDJ = 14 ps)
© Semiconductor Components Industries, LLC, 2011
October, 2011 − Rev. 2
1
Publication Order Number:
NB6L14S/D
NB6L14S
Q0
Q0
VCC GND
16
15
14
Exposed Pad (EP)
13
Q1
1
12 IN
Q1
2
11 VT
Q2
3
NB6L14S
Q2
Table 1. TRUTH TABLE
10 VREFAC
4
9
IN
IN
IN
EN
Q
Q
0
1
1
0
1
1
0
1
1
0
x
x
0
0 (Note 1)
1 (Note 1)
1. On next transition of the input signal (IN).
5
6
7
Q3
Q3
VCC
8
EN
Figure 3. NB6L14S Pinout, 16−pin QFN (Top View)
Table 2. PIN DESCRIPTION
Pin
Name
I/O
Description
1
Q1
LVDS Output
Non−inverted IN output. Typically loaded with 100 W receiver termination
resistor across differential pair.
2
Q1
LVDS Output
Inverted IN output. Typically loaded with 100 W receiver termination resistor
across differential pair.
3
Q2
LVDS Output
Non−inverted IN output. Typically loaded with 100 W receiver termination
resistor across differential pair.
4
Q2
LVDS Output
Inverted IN output. Typically loaded with 100 W receiver termination resistor
across differential pair.
5
Q3
LVDS Output
Non−inverted IN output. Typically loaded with 100 W receiver termination
resistor across differential pair.
6
Q3
LVDS Output
Inverted IN output. Typically loaded with 100 W receiver termination resistor
across differential pair.
7
VCC
−
8
EN
LVTTL / LVCMOS Input
9
IN
LVPECL, CML, LVDS
10
VREFAC
LVPECL Output
The VREFAC reference output can only be used to rebias capacitor−coupled
differential or single−ended input signals. For the capacitor−coupled IN and/or
INb inputs, VREFAC should be connected to the VT pin and bypassed to ground
with a 0.01 mF capacitor.
Internal 100 W Center−tapped Termination Pin for IN and IN
Positive Supply Voltage.
Synchronous Output Enable. When LOW, Q outputs will go LOW and Qb
outputs will go HIGH on the next negative transition of IN input. The internal
DFF register is clocked on the falling edge of IN input; see Figure 26. The EN
pin has an internal pullup resistor and defaults HIGH when left open.
Inverted Differential Input
11
VT
LVPECL Output
12
IN
LVPECL, CML, LVDS
13
GND
−
Negative Supply Voltage.
14
VCC
−
Positive Supply Voltage.
15
Q0
LVDS Output
Non−inverted IN output. Typically loaded with 100 W receiver termination
resistor across differential pair.
16
Q0
LVDS Output
Inverted IN output. Typically loaded with 100 W receiver termination resistor
across differential pair.
−
EP
−
Non−inverted Differential Input. (Note 2)
The Exposed Pad (EP) on the QFN−16 package bottom is thermally connected
to the die for improved heat transfer out of package. The exposed pad must be
attached to a heat−sinking conduit. The pad is not electrically connected to the
die, but is recommended to be electrically and thermally connected to GND on
the PC board.
2. In the differential configuration, when the input termination pin (VT) is connected to a termination voltage or left open, and if no signal is applied
on IN/IN inputs, then the device will be susceptible to self−oscillation.
http://onsemi.com
2
NB6L14S
Table 3. ATTRIBUTES
Characteristics
Value
Moisture Sensitivity (Note 3)
Flammability Rating
ESD Protection
Level 1
Oxygen Index: 28 to 34
Human Body Model
Machine Model
UL 94 V−0 @ 0.125 in
> 2 kV
> 200 V
Transistor Count
745
Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test
3. For additional information, see Application Note AND8003/D.
Table 4. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
VCC
Positive Power Supply
GND = 0 V
VIN
Positive Input
GND = 0 V
IIN
Input Current Through RT (50 W Resistor)
Static
Surge
IOSC
Output Short Circuit Current
Line−to−Line (Q to Q)
Line−to−End (Q or Q to GND)
IREF_AC
VREF_AC Sink/Source Current
TA
Operating Temperature Range
Tstg
Storage Temperature Range
qJA
Thermal Resistance (Junction−to−Ambient) (Note 4)
0 lfpm
500 lfpm
qJC
Thermal Resistance (Junction−to−Case)
1S2P (Note 4)
Tsol
Wave Solder
Q or Q
Q to Q to GND
Condition 2
VIN ≤ VCC
Continuous
Continuous
QFN−16
Pb−Free
Rating
Unit
3.8
V
3.8
V
35
70
mA
mA
12
24
mA
"0.5
mA
−40 to +85
°C
−65 to +150
°C
QFN−16
QFN−16
41.6
35.2
°C/W
°C/W
QFN−16
4.0
°C/W
265
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
4. JEDEC standard multilayer board − 1S2P (1 signal, 2 power) with 8 filled thermal vias under exposed pad.
http://onsemi.com
3
NB6L14S
Table 5. DC CHARACTERISTICS VCC = 2.375 V to 2.625 V, GND = 0 V, TA = −40°C to +85°C
Symbol
ICC
Characteristic
Min
Power Supply Current (Note 9)
Typ
Max
Unit
65
100
mA
DIFFERENTIAL INPUTS DRIVEN SINGLE−ENDED (Figures 17, 18, 22, and 24)
Vth
Input Threshold Reference Voltage Range (Note 8)
GND +100
VCC − 100
mV
VIH
Single−ended Input HIGH Voltage
Vth + 100
VCC
mV
VIL
Single−ended Input LOW Voltage
GND
Vth − 100
mV
VREFAC
Reference Output Voltage (Note 11)
VCC − 1.300
V
VCC − 1.600
VCC − 1.425
DIFFERENTIAL INPUTS DRIVEN DIFFERENTIALLY (Figures 10, 12, NO TAG, NO TAG, 23, and 25)
VIHD
Differential Input HIGH Voltage
100
VCC
mV
VILD
Differential Input LOW Voltage
GND
VIHD − 100
mV
VCMR
Input Common Mode Range (Differential Configuration)
GND + 50
VCC − 50
mV
VID
Differential Input Voltage (VIHD − VILD)
100
VCC
mV
RTIN
Internal Input Termination Resistor
40
60
W
450
mV
25
mV
1375
mV
1
25
mV
1425
1600
mV
50
LVDS OUTPUTS (Note 5)
VOD
Differential Output Voltage
250
DVOD
Change in Magnitude of VOD for Complementary Output States
(Note 10)
VOS
Offset Voltage (Figure 21)
DVOS
Change in Magnitude of VOS for Complementary Output States
(Note 10)
VOH
Output HIGH Voltage (Note 6)
VOL
Output LOW Voltage (Note 7)
0
1
1125
0
900
1075
mV
LVTTL/LVCMOS INPUT, EN
VIH
Input HIGH Voltage
2.0
VCC
V
VIL
Input LOW Voltage
GND
0.8
V
IIH
Input HIGH Current
−150
150
mA
IIL
Input LOW Current
−150
150
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
5. LVDS outputs require 100 W receiver termination resistor between differential pair. See Figure 20.
6. VOHmax = VOSmax + ½ VODmax.
7. VOLmax = VOSmin − ½ VODmax.
8. Vth is applied to the complementary input when operating in single−ended mode.
9. Input termination pins open at the DC level within VCMR and output pins loaded with RL = 100 W across differential.
10. Parameter guaranteed by design verification not tested in production.
11. VREFAC used to rebias capacitor−coupled inputs only (see Figures 17 and 18).
http://onsemi.com
4
NB6L14S
Table 6. AC CHARACTERISTICS VCC = 2.375 V to 2.625 V, GND = 0 V; (Note 12)
−40°C to +85°C
Min
Characteristic
Symbol
Typ
finMax
Maximum Input Clock Frequency
VOUTPP
Output Voltage Amplitude (@ VINPPmin)
(Figure 4)
fDATA
Maximum Operating Data Rate
2.5
tPLH,
tPHL
Differential Input to Differential Output, IN to Q
Propagation Delay @ 100 MHz
300
450
ts
th
Setup Time
Hold Time
300
500
20
20
tSKEW
Within Device Skew (Note 17)
Device−to−Device Skew (Note 16)
tJITTER
RMS Random Clock Jitter (Note 14)
Deterministic Jitter (Note 15)
VINPP
Input Voltage Swing/Sensitivity
(Differential Configuration) (Note 13)
tr
tf
Output Rise/Fall Times @ 250 MHz
(20% − 80%)
Max
2.0
fin ≤ 1.0 GHz
fin= 1.5 GHz
fin= 2.0 GHz
220
200
170
EN to IN/IN
350
300
270
mV
Gb/s
fin = 2.0 GHz
fDATA v 2.488 Gb/s
600
ps
5
30
20
200
ps
0.5
5.0
0.8
20
ps
VCC−GND
mV
225
ps
100
Q, Q
Unit
GHz
70
150
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
12. Measured by forcing VINPPmin with 50% duty cycle clock source and VCC − 1400 mV offset. All loading with an external RL = 100 W. Input
edge rates 150 ps (20%−80%). See Figure 20.
13. Input voltage swing is a single−ended measurement operating in differential mode.
14. RMS jitter with 50% Duty Cycle clock signal at 750 MHz.
15. Deterministic jitter with input NRZ data at PRBS 223−1 and K28.5.
16. Skew is measured between outputs under identical transition @ 250 MHz.
17. The worst case condition between Q0/Q0 and Q1/Q1 from either D0/D0 or D1/D1, when both outputs have the same transition.
OUTPUT VOLTAGE AMPLITUDE (mV)
400
350
300
250
200
150
100
50
0
0
0.5
1
1.5
2
2.5
INPUT CLOCK FREQUENCY (GHz)
Figure 4. Output Voltage Amplitude (VOUTPP) versus
Input Clock Frequency (fin) and Temperature (@ VCC = 2.5 V)
http://onsemi.com
5
3
NB6L14S
Figure 5. Typical Phase Noise Plot at
fcarrier = 311.04 MHz
Figure 6. Typical Phase Noise Plot at
fcarrier = 622.08 MHz
Figure 7. Typical Phase Noise Plot at
fcarrier = 1 GHz
Figure 8. Typical Phase Noise Plot at
fcarrier = 1.5 GHz
device (integrated between 12 kHz and 20 MHz; as shown
in the shaded region of the plot) at each of the frequencies
is 65 fs, 29 fs, 24 fs and 20 fs respectively. The input source
used for the phase noise measurements is Agilent E8663B.
The above phase noise plots captured using Agilent
E5052A show additive phase noise of the NB6L14S device
at frequencies 311.04 MHz, 622.08 MHz, 1 GHz and
1.5 GHz respectively at an operating voltage of 2.5 V in
room temperature. The RMS Phase Jitter contributed by the
http://onsemi.com
6
VOLTAGE (63.23 mV/div)
NB6L14S
Device DDJ = 10 ps
TIME (58 ps/div)
Figure 9. Typical Output Waveform at 2.488 Gb/s with PRBS 223−1 and OC48 mask
(VINPP = 100 mV; Input Signal DDJ = 14 ps)
VCC = 3.3 V or 2.5 V
VCC = 2.5 V
VCC = 3.3 V or 2.5 V
VCC
VCC = 2.5 V
0.1 mF
Zo = 50 W
LVPECL
Driver
NB6L14S
IN
50 W
VT = VCC − 2.0 V
Zo = 50 W
19 W
GND
VEE / GND
Figure 10. LVPECL Interface
GND
VCC = 2.5 V
NB6L14S
IN
Zo = 50 W
50 W
VT = VCC
50 W
Zo = 50 W
IN
GND
NB6L14S
IN
50 W
CML
Driver
VT = OPEN
Zo = 50 W
GND
VCC = 2.5 V
50 W
LVDS
Driver
IN
Figure 11. LVPECL Y−Termination Interface
VCC = 2.5 V
Zo = 50 W
50 W
50 W
IN
VEE / GND
VCC = 3.3 V or 2.5 V
VT
LVPECL
Driver
50 W
Zo = 50 W
NB6L14S
IN
Zo = 50 W
GND
IN
GND
Figure 12. LVDS Interface
GND
Figure 13. CML Interface
http://onsemi.com
7
NB6L14S
VCC = 3.3 V or 2.5 V
VCC = 2.5 V
Zo = 50 W
VCC = 2.5 V
VCC = 2.5 V
NB6L14S
IN
Zo = 50 W
50 W
HSTL
Driver
VT = GND
50 W
Zo = 50 W
VT = OPEN
LVCMOS
Driver
NB6L14S
IN
50 W*
50 W*
IN
IN
2.5 kW
GND
GND
GND
Figure 14. HSTL Interface
VCC = 2.5 V
LVTTL
Driver
VT = OPEN
VCC
VCC = 2.5 V
NB6L14S
IN
Zo = 50 W
50 W*
50 W*
VT = VREFAC*
50 W
Zo = 50 W
IN
GND
NB6L14S
IN
50 W
Differential
Driver
1.5 kW
GND
GND
Figure 15. LVCMOS Interface
VCC = 2.5 V
Zo = 50 W
GND
GND
GND
IN
GND
Figure 17. Capacitor−Coupled Differential
Interface (VT Connected to VREF_AC)
Figure 16. LVTTL Interface
*VREFAC bypassed to ground with a 0.1 mF capacitor.
VCC
VCC = 2.5 V
Zo = 50 W
NB6L14S
IN
50 W
Single−Ended
Driver
VT = VREFAC*
50 W
IN
GND
GND
Figure 18. Capacitor−Coupled Single−Ended Interface (VT Connected to VREFAC)
*VREFAC bypassed to ground with a 0.1 mF capacitor.
http://onsemi.com
8
NB6L14S
IN
VINPP = VIH(D) − VIL(D)
IN
Q
VOUTPP = VOH(Q) − VOL(Q)
Q
tPHL
tPLH
Figure 19. AC Reference Measurement
Q
LVDS
Driver
Device
Zo = 50 W
HI Z Probe
D
100 W
Q
Zo = 50 W
Oscilloscope
D
HI Z Probe
Figure 20. Typical LVDS Termination for Output Driver and Device Evaluation
QN
VOH
VOS
VOD
VOL
QN
Figure 21. LVDS Output
IN
VIH
IN
Vth
VIL
Vth
IN
IN
Figure 22. Differential Input Driven
Single−Ended
Figure 23. Differential Inputs Driven
Differentially
VCC
VCC
VCMRmax
VIHmax
Vthmax
IN
VILD(MAX)
VILmax
VCMR
Vth
Vthmin
GND
VIHD(MAX)
VIHD
VID = VIHD − VILD
VILD
VIHmin
IN
VILmin
VCMRmin
GND
Figure 24. Vth Diagram
VIHD(MIN)
VILD(MIN)
Figure 25. VCMR Diagram
http://onsemi.com
9
NB6L14S
EN
VCC/2
VCC/2
tS
IN
IN
tH
tpd
Q
Q
Figure 26. EN Timing Diagram
Figure 27. Tape and Reel Pin 1 Quadrant Orientation
ORDERING INFORMATION
Package
Shipping†
NB6L14SMNG
QFN−16, 3 X 3 mm
(Pb−Free)
123 Units / Rail
NB6L14SMNTXG
QFN−16, 3 X 3 mm
(Pb−Free)
3000 / Tape & Reel
(Pin 1 Orientation in Quadrant B, Figure 27)
NB6L14SMNTWG
QFN−16, 3 X 3 mm
(Pb−Free)
3000 / Tape & Reel
(Pin 1 Orientation in Quadrant A, Figure 27)
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
10
NB6L14S
PACKAGE DIMENSIONS
QFN16 3x3, 0.5P
CASE 485G−01
ISSUE E
D
ÇÇÇ
ÇÇÇ
ÇÇÇ
PIN 1
LOCATION
2X
A
B
L
DETAIL A
ALTERNATE TERMINAL
CONSTRUCTIONS
E
ÉÉ
ÉÉ
EXPOSED Cu
0.10 C
TOP VIEW
DETAIL B
0.05 C
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.25 AND 0.30 MM FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
L1
0.10 C
2X
L
(A3)
ÇÇ
ÉÉ
A1
DETAIL B
A
0.05 C
A3
MOLD CMPD
ALTERNATE
CONSTRUCTIONS
NOTE 4
A1
SIDE VIEW
C
SEATING
PLANE
16X
L
D2
16X
9
16X
0.58
PACKAGE
OUTLINE
8
4
MILLIMETERS
MIN
MAX
0.80
1.00
0.00
0.05
0.20 REF
0.18
0.30
3.00 BSC
1.65
1.85
3.00 BSC
1.65
1.85
0.50 BSC
0.18 TYP
0.30
0.50
0.00
0.15
RECOMMENDED
SOLDERING FOOTPRINT*
0.10 C A B
DETAIL A
DIM
A
A1
A3
b
D
D2
E
E2
e
K
L
L1
1
E2
K
2X
2X
1.84 3.30
1
16
e
e/2
BOTTOM VIEW
16X
16X
0.30
b
0.10 C A B
0.05 C
0.50
PITCH
NOTE 3
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
AnyLevel and ECLinPS MAX are trademarks of Semiconductor Components Industries, LLC (SCILLC).
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
11
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NB6L14S/D