OPTOTRONIC® OT 45/220-240/700 LTCS 700mA Constant Current LED Power Supply with and DIPswitch Technical Information Edition: August 2012 subject to change Technical data Reference: For LED modules: Nominal Voltage: OT 45/220-240/700 LTCS 350 - 700 mA LED 220 – 240 VAC Line Current, nominal: Mains Frequency: Protection Class: Output Current: (Remark) Output voltage: (Remark) Interface: Output Power: (Remark) Power Loss: ECG efficiency: (Remark) Power Loss in standby mode (Remark): Input Voltage: (Remark) DC Voltage: 230 mA @ 230V 50/60 Hz II 100 - 700 mADC +/- 5% (350-700mA) 38 - 120 VDC maximum 120VDC LEDset and DIPswitch 45 W Partial Load 11W .. 45W, see load diagramm > 0,95 (full load) @ 230V > 0,85 (half load) @ 230V 6 W max. 89% full load at 230V < 1,5 W LEDset turned off 195 – 264 VAC Permitted voltage range No Internal Control No-load proof: Hot plug functionality: (Remark) Short circuit protection: Overload protection: Overtemperature protection: LEDset and DIPswitch Yes Yes Max turn-on delay after hot-plug = 25s Automatic, reversible Automatic, reversible Automatic, reversible Ambient temperature range, ta: Max. case temperature at tc point: ECG Lifetime: (Remark) Maximum casing temperature in case of fault -25 °C to +50 °C 90 °C 50.000h at tcase= 80 °C at tc point and 10% failure rate Rated Power factor: 20120822 AA31919 110°C Page 1 of 6 OPTOTRONIC® Technical Information OT 45/220-240/700 LTCS 700mA Constant Current LED Power Supply with and DIPswitch Inrush current: (Remark) Max. no. of ECG @ circuit breakers 10 A (B type): Max. no. of ECG @ circuit breakers 16 A (B type): Max. no. of ECG @ circuit breakers 16 A (B type): in combination with EBN-OS Edition: August 2012 subject to change 8A twidth = 55 µs (measured at 50% Ipeak) 40 60 60 Terminal: Mains (grey) Functional earth (grey) LEDset (grey [GNDset], purple [Vset], blue [+12Vset]) LEDModule ( [+] red/ [-] black) Cable cross section input side 0,2 mm² – 1,5 mm² (Remark) Wire preparation length Input side: Solid and flexible 8,5 – 9,5 mm Cable cross section output side: 0,2 mm² – 1,5 mm² (Remark) Wire preparation length output side: Max. cable length - system: Geometry (l x b x h): Weight: IP Code: (Remark) Safety: Performance: Radio interference: Harmonic content: Immunity: Surge capability: Galvanic isolation primary/secondary : (Remark) Solid and flexible, LEDset only 0,2mm2 – 0,5mm2 8,5 – 9,5 mm 2m 123 x 79 x 33 mm (K3) 240 g IP20 IEC 61347-1, IEC 61347-2-13 IEC 62384 EN 55015:2006+A1:2007+A2:2009 IEC 61000-3-2 IEC 61547:1995+A1:2000 L-N: 1,6kV, L/N – Functional Earth: 2kV 3,75 kVrms SELV-equivalent Approvals: Remark: An optional cable clamp is available. This cable clamp can be snapped onto the ECG and thus converts it into an ECG suitable for independent installation. Suitable cables are listed in cable clamp datasheet. QT Cable Clamp K3 OTp Cable Clamp 20120822 AA31919 EAN 10 (1 pc) 4008321190741 4008321966155 Page 2 of 6 EAN 40 (10 pcs) 4008321190758 4008321966162 OPTOTRONIC® Technical Information OT 45/220-240/700 LTCS 700mA Constant Current LED Power Supply with and DIPswitch Edition: August 2012 subject to change Geometry Ordering information EAN 10 (1 pc) 4008321664433 OT 45/220-240/700 LTCS EAN 40 (20 pcs) 4008321664440 Wiring diagram ~ L/N (PE/FE) OT 45/220-240/700 LTCS on on LED LEDset DIP1 DIP2 20120822 AA31919 DIPswitch 350mA/500mA/700mA/LEDset GNDset (LEDset Interface) Vset +12Vset + Page 3 of 6 LED OPTOTRONIC® Technical Information OT 45/220-240/700 LTCS Edition: August 2012 700mA Constant Current LED Power Supply with and DIPswitch subject to change OT 45/220-240/700 LTCS: Output Characteristic Output Characteristics 130 120V 120 40-45W 35-40W 30-35W <30W 110 100 90 U-out [V] 80 70 60 50 A 40 B 38V 30 20 10 0 0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 Iout [mA] [B] Nominal Operating Range, [A] + [B] LEDset Current Range DIPswitch DIP1 Off Off On On DIP2 Off On Off On Current LEDset 700mA 500mA 350mA LEDset interface LEDset allows to control the output current of the control gear (ref. to LEDset application note). The input voltage of the Vset pin defines the output current relative to the maximum nominal current of the control gear. LEDset interface is not isolated to the secondary side of the LED driver output. +12Vset Vset GNDset 20120822 AA31919 Auxiliary supply 12V +15/-8%, 15mA max. Signal input, included current source 274µA 0V < Vset < 12V +15% Reference ground for +12Vset and Vset Page 4 of 6 OPTOTRONIC® Technical Information OT 45/220-240/700 LTCS Edition: August 2012 700mA Constant Current LED Power Supply with and DIPswitch subject to change The relation between input voltage and output current is as following: 700mA 600mA Protection region Iout 500mA 400mA 300mA 200mA 100mA OFF 1V 3V 5V 7V 9V 11V Vset Output current relative to the nominal current Iout [% of Imax]=(Vset-1V)/(10V-1V) between Imin and Imax LEDset and DIPswitch The output current could also be set in combination with the DIPswitch current pre-selection (350,500 and 700mA) and the LEDset interface. In those three operation modes the ECG does not switch off as soon as Vset exceeds 11V (no protection region). DIPxx = 700mA LEDset 700mA 600mA DIPxx = 500mA LEDset Iout 500mA 400mA DIPxx = 350mA LEDset 300mA 200mA 100mA OFF 1V 3V 5V 7V Vset 20120822 AA31919 Page 5 of 6 9V 11V OPTOTRONIC® Technical Information OT 45/220-240/700 LTCS 700mA Constant Current LED Power Supply with and DIPswitch Edition: August 2012 subject to change Efficiency [%] OT 45/220-240/700 LTCS Typical Efficiency and Power Factor versus Load 100,0 1,5 90,0 1,4 80,0 1,3 70,0 1,2 700mA 60,0 1,1 500mA 350mA 50,0 1,0 700mA 40,0 0,9 350mA 30,0 0,8 20,0 0,7 10,0 0,6 0,0 0,0 5,0 10,0 15,0 20,0 25,0 30,0 35,0 40,0 Power Factor 500mA 0,5 45,0 Output Power [W] Earth connection Earth connection is not required but may be used to improve EMI performance of the installation Wrong wiring This control gear is inherently protected against wrong wiring. The wrong connections between LED+ with Vset and GNDset could damage irreversibly the ECG. All the other wrong wirings on the secondary side, once removed, make the ECG work regularly. LED- and GNDset terminals cannot be connected together. Installation notes The luminaire manufacturer is responsible for providing the required clearances and creepage distances and also for the protection against electrical shock, especially for the line and load wires according EN 60598. Instruction sheet Please consult the instruction sheet for further important information on e.g. wire stripping and wiring limitations in system installations. The instruction sheet is enclosed with the device or available upon request. 20120822 AA31919 Page 6 of 6