pdf

OPTOTRONIC®
OT 35/220-240/700 LTCS
700mA Constant Current LED Power Supply
with
and DIPswitch
Technical
Information
Edition: August 2012
subject to change
Technical data
Reference:
For LED modules:
Nominal Voltage:
OT 35/220-240/700 LTCS
350 - 700 mA LED
220 – 240 VAC
Line Current, nominal:
Mains Frequency:
Protection Class:
Output Current:
(Remark)
Output voltage:
(Remark)
Output Power:
(Remark)
Power Loss:
ECG efficiency:
(Remark)
Power Loss in standby mode
(Remark):
Input Voltage:
(Remark)
DC Voltage:
190 mA @ 230V
50/60 Hz
II
100 - 700 mADC
+/- 5% (350-700mA)
24 - 87 VDC
maximum 100VDC
35 W
Partial Load 9W .. 35W, see load diagramm
> 0,95 (full load) @ 230V
> 0,85 (half load) @ 230V
5 W max.
88%
full load at 230V
< 1,5 W
LEDset turned off
195 – 264 VAC
Permitted voltage range
No
Internal Control:
No-load proof:
Hot plug functionality:
(Remark)
Short circuit protection:
Overload protection:
Overtemperature protection:
LEDset and DIPswitch
Yes
Yes
Max turn-on delay after hot-plug = 15s
Automatic, reversible
Automatic, reversible
Automatic, reversible
Ambient temperature range, ta:
Max. case temperature at tc point:
ECG Lifetime:
(Remark)
Maximum casing temperature in case
of fault
-25 °C to +50 °C
85 °C
50.000h
at tcase= 75 °C at tc point and 10% failure rate
Rated Power factor:
20120822
AA31918
100°C
Page 1 of 6
OPTOTRONIC®
Technical
Information
OT 35/220-240/700 LTCS
700mA Constant Current LED Power Supply
with
and DIPswitch
Inrush current:
(Remark)
Max. no. of ECG @ circuit breakers
10 A (B type):
Max. no. of ECG @ circuit breakers
16 A (B type):
Max. no. of ECG @ circuit breakers
16 A (B type):
in combination with EBN-OS
Edition: August 2012
subject to change
8A
twidth = 55 µs (measured at 50% Ipeak)
52
84
84
Terminal:
Mains (grey)
Functional earth (grey)
LEDset (grey [GNDset], purple [Vset], blue [+12Vset])
LEDModule ( [+] red/ [-] black)
Cable cross section input side
0,2 mm² – 1,5 mm²
(Remark)
Wire preparation length Input side:
Solid and flexible
8,5 – 9,5 mm
Cable cross section output side:
0,2 mm² – 1,5 mm²
(Remark)
Wire preparation length output side:
Max. cable length - system:
Geometry (l x b x h):
Weight:
IP Code:
(Remark)
Safety:
Performance:
Radio interference:
Harmonic content:
Immunity:
Surge capability:
Galvanic isolation
primary/secondary :
(Remark)
Solid and flexible, LEDset only 0,2mm2 – 0,5mm2
8,5 – 9,5 mm
2m
123 x 79 x 33 mm (K3)
220 g
IP20
IEC 61347-1, IEC 61347-2-13
IEC 62384
EN 55015:2006+A1:2007+A2:2009
IEC 61000-3-2
IEC 61547:1995+A1:2000
L-N: 1,6kV, L/N – Functional Earth: 2kV
3,75 kVrms
SELV-equivalent
Approvals:
Remark:
An optional cable clamp is available. This cable clamp can be snapped onto the ECG and thus converts it
into an ECG suitable for independent installation. Suitable cables are listed in cable clamp datasheet.
QT Cable Clamp K3
OTp Cable Clamp
20120822
AA31918
EAN 10 (1 pc)
4008321190741
4008321966155
Page 2 of 6
EAN 40 (10 pcs)
4008321190758
4008321966162
OPTOTRONIC®
Technical
Information
OT 35/220-240/700 LTCS
700mA Constant Current LED Power Supply
with
and DIPswitch
Edition: August 2012
subject to change
Geometry
Ordering information
EAN 10 (1 pc)
4008321664419
OT 35/220-240/700 LTCS
EAN 40 (20 pcs)
4008321664426
Wiring diagram
~
L/N
(PE/FE)
OT 35/220-240/700 LTCS
on on
LED
LEDset
DIP1
DIP2
20120822
AA31918
DIPswitch
350mA/500mA/700mA/LEDset
GNDset
Vset
(LEDset Interface)
+12Vset
+
Page 3 of 6
LED
OPTOTRONIC®
Technical
Information
OT 35/220-240/700 LTCS
Edition: August 2012
700mA Constant Current LED Power Supply
with
and DIPswitch
subject to change
OT 35/220-240/700
LTCS: Output Characteristic
Output Characteristics
130
120
110
30-35W
25-30W
20-25W
<20W
100
87V
90
U-out [V]
80
70
60
50
40
A
30
B
24V
20
10
0
0
50
100
150
200
250
300
350
400
450
500
550
600
650
700
Iout [mA]
[B] Nominal Operating Range, [A] + [B] LEDset Current Range
DIPswitch
DIP1
Off
Off
On
On
DIP2
Off
On
Off
On
Current
LEDset
700mA
500mA
350mA
LEDset interface
LEDset allows to control the output current of the control gear (ref. to LEDset application note).
The input voltage of the Vset pin defines the output current relative to the maximum nominal
current of the control gear. LEDset interface is not isolated to the secondary side of the LED
driver output.
+12Vset
Vset
GNDset
20120822
AA31918
Auxiliary supply 12V +15/-8%, 15mA max.
Signal input, included current source 274µA
0V < Vset < 12V +15%
Reference ground for +12Vset and Vset
Page 4 of 6
OPTOTRONIC®
Technical
Information
OT 35/220-240/700 LTCS
Edition: August 2012
700mA Constant Current LED Power Supply
with
and DIPswitch
subject to change
The relation between input voltage and output current is as following:
700mA
600mA
Protection region
Iout
500mA
400mA
300mA
200mA
100mA
OFF
1V
3V
5V
7V
9V
11V
Vset
Output current relative to the nominal current
Iout [% of Imax]=(Vset-1V)/(10V-1V) between Imin and Imax
LEDset and DIPswitch
The output current could also be set in combination with the DIPswitch current pre-selection
(350,500 and 700mA) and the LEDset interface. In these three operation modes the ECG does
not switch off as soon as Vset exceeds 11V (no protection region).
DIPxx = 700mA
LEDset
700mA
600mA
DIPxx = 500mA
LEDset
Iout
500mA
400mA
DIPxx = 350mA
LEDset
300mA
200mA
100mA
OFF
1V
3V
5V
7V
Vset
20120822
AA31918
Page 5 of 6
9V
11V
OPTOTRONIC®
Technical
Information
OT 35/220-240/700 LTCS
Edition: August 2012
700mA Constant Current LED Power Supply
with
and DIPswitch
subject to change
Efficiency [%]
OT 35/220-240/700
LTCS versus Load
Typical Efficiency
and Power Factor
100
1,5
90
1,4
80
1,3
70
1,2
700
60
1,1
500
350
1,0
700
500
40
0,9
350
30
0,8
20
0,7
10
0,6
0
Power Factor
50
0,5
0
5
10
15
20
25
30
35
Output Power [W]
Earth connection
Earth connection is not required but may be used to improve EMI performance of the installation.
Wrong wiring
This control gear is inherently protected against wrong wiring. The wrong connections between
LED+ with Vset and GNDset could damage irreversibly the ECG. All the other wrong wirings on
the secondary side, once removed, make the ECG work regularly. LED- and GNDset terminals
cannot be connected together.
Installation notes
The luminaire manufacturer is responsible for providing the required clearances and creepage
distances and also for the protection against electrical shock, especially for the line and load
wires according EN 60598.
Instruction sheet
Please consult the instruction sheet for further important information on e.g. wire stripping and
wiring limitations in system installations. The instruction sheet is enclosed with the device or
available upon request.
20120822
AA31918
Page 6 of 6