NB3N1900K Evaluation Board User's Manual

NB3N1900KMNGEVB
NB3N1900K
Evaluation Board
User's Manual
Introduction
http://onsemi.com
The NB3N1900KMNGEVB evaluation boards were
developed for the NB3N1900K (HCSL) devices. This
evaluation board was designed to provide a flexible and
convenient platform to quickly evaluate, characterize and
verify the operation of the NB3N1900K devices.
This evaluation board manual contains:
• Information on the NB3N1900K Evaluation Board
• Assembly Instructions
• Test and Measurement Setup Procedures
• Board Schematic and Bill of Materials
This manual should be used in conjunction with the device
datasheet which contains full technical details on the device
specifications and operation.
(Top View)
(Bottom View)
EVAL BOARD USER’S MANUAL
Figure 1. NB3N1900KMNGEVB Evaluation Board
© Semiconductor Components Industries, LLC, 2014
October, 2014 − Rev. 1
1
Publication Order Number:
EVBUM2256/D
NB3N1900KMNGEVB
BOARD FEATURES
• All Layers are Constructed with FR4 Dielectric
Single Board Design/Layout
• Accommodates the Electrical Characterization of the
•
•
•
•
Material
• The First Layer is the Primary Signal Layer, Including
NB3N1900K (HCSL Outputs)
Incorporates On-board I2C/SMBus Interface Circuitry
Powered from a USB Connection, Minimizing Cabling
Convenient and Compact Board Layout
3.3 V Power Supply Device Operation
Differential Inputs/Outputs Signals are Accessed via
SMA Connectors or High Impedance Probes
•
•
•
Other Board Features
There are no vias on the high-speed differential I/O metal
traces so as to eliminate via impedance and stub affects.
Board stand-offs are installed.
All of the Differential Inputs and Outputs
The Second Layer is the Ground Plane. It is Dedicated
for the DUT Ground/SMA Ground Plane
The Third Layer is Dedicated as the Power Plane.
A Portion of this 3rd Layer is Designated for the Device
VDD and VDDIO Power Planes
The Fourth Layer Contains Control Lines, Power
Supply Banana Jacks and Device Power Pin By-pass
Capacitors
Layer Stack
L1 (Top) Signal
L2 Device Ground and SMA Ground
L3 VDD, VDDIO (Separate Device Power Supplies)
L4 (Bottom), Power Supply By-pass Capacitors,
Control Pin Traces and Banana Jacks
•
•
•
•
Board Layout
The NB3N1900K QFN−72 Evaluation Board provides
a high bandwidth, 50-W controlled trace impedance
environment (100-W line-to-line differential) and is
implemented in four layers.
Figure 2. NB3N1900KMNGEVB Evaluation Board Layer Stack-Up
Power Supplies
Board Layer #3 = VDD and VDDIO Power Supplies
VDD = positive power supply for core and inputs;
VDD/VDDA/VDDR (pins #1, 8)
VDDIO = positive power supply for outputs; VDDIO
(pins #21, 31, 45, 58, 68)
Each VDD, VDDIO and GND power supply has
a separate side-launch banana jack located on bottom side.
This board is capable of measuring device IDD & IDDIO
separately.
Board Layer #2 = SMA Ground = Device GND = 0 V.
GND Banana Jack = negative power supply for DUTGND
and SMAGND.
VDD & VDDIO have the power supply filtering per
datasheet by the banana jacks.
All VDD/VDDA/VDDR/VDDIO device pins have
a 0.1 mF bypass capacitor installed on top side next to
package pins.
Exposed Pad (EP): The exposed pad footprint on the board
is soldered to the exposed pad of the QFN−72 package, and
is electrically connected to GND power supply.
http://onsemi.com
2
NB3N1900KMNGEVB
• For a HIGH Level – Put Jumper to High
• For a LOW Level − Put Jumper to Low
• For a MID Level − Put Jumper to both High and Low;
Control Pins
Each control pin can be managed manually with a H/L
jumper header; H = VDD, L = GND.
this will Enable both Pull-up and Pull-down Resistors
Tri-Level Input Pins − HBW_BYP_LBW#, SA_0 and SA_1
The three tri-level input pins, HBW_BYPASS_LBW#,
SA0 and SA1, have selectable (with jumper) 4.7 kW pull-up
to VDD and 4.7 kW pull-down to GND resistors; No jumper
defaults to open/float.
HBW_BYP_LBW#
At J16 header, there is a 4.7 kW pull-up to VDD and
a 4.7 kW pull-down resistor to GND for manual control.
Figure 3. HBW_BYP_LBW# Schematic Configuration
SA_0 & SA_1
At J21 and J23 headers, there are 4.7 kW pull-ups to VDD
and 4.7 kW pull-down resistors to GND for manual control.
Figure 4. SA_0 & SA_1 Schematic Configuration
OE_n# Pins (Output Enable/Disable Function)
Four of the eight differential outputs can be controlled
manually using the convenient High/Low OE_n# jumpers.
See Figure 5.
All eight of the OE_n#s can be controlled individually/
automatically by using the software GUI. GUI control is
accomplished via the USB. See Figure 5.
http://onsemi.com
3
NB3N1900KMNGEVB
Figure 5. OE_n# Pins Schematic Configuration
100M_133M# − Frequency Selection (J18)
The 100M_133M# frequency selection pin can be
controlled manually with the High/Low header jumper J18,
H = 100 MHz, L = 133 MHz.
Figure 6. 100M_133M# Pin Schematic Configuration
PWRGD/PWRDN# (J19)
The PWRGD/PWRDN# pin can be controlled manually
with the High/Low header jumper J19; H = PWRGD,
L = PWRDN#.
Figure 7. PWRGD/PWRDN# Pin Schematic Configuration
http://onsemi.com
4
NB3N1900KMNGEVB
Differential Clock Inputs and Outputs
Six of the nineteen differential outputs are designed to
have equal length metal traces from the device pins to the
SMA connectors.
The other thirteen differential outputs have shortened
metal traces, do not have SMA connectors and can be
observed with a high-impedance probe on the metal pads
provided.
Each DIF_n/DIF_n# output has a provision for CLoad; 2 pF
capacitors are installed on all outputs.
RS & RP pads are located close to the DUT. RS = 33-W is
installed for the NB3N1900K.
NB3N1900K (HCSL Outputs): RP can be uninstalled on the
six output pair with long metal traces to SMA connectors;
Use 50-W to GND of the oscilloscope head for RP.
CLK_IN & CLK_IN# − Differential Clock Inputs
The differential Clock input traces, CLK_IN/CLK_IN#,
are equal length routed straight from the SMA connectors on
the left side directly to the DUT; there are no vias on metal
traces.
CLK_IN & CLK_IN# have resistor pads (R63 & R64) to
GND to terminate a signal generator, if used. 50-W resistors
are installed. Remove these resistors if CLK_IN &
CLK_IN# are driven by another IC device.
DIF_n and DIF_n# − Differential Outputs
NB3N1900KMNGEVB were designed to measure the
differential HCSL outputs with a 50-W scope head or
high-impedance FET probe. (See Output Schematic in
Figure 8)
RP is installed (50-W to GND) on the short metal traces
without SMA connectors and will use Hi-Z probes.
Table 1. NB3N1900KMNGEVB OUTPUT LOAD AND TERMINATION VS. OSCILLOSCOPE MEASUREMENT
Device
Output Traces
RS
RP
CLoad
Scope
1900K
Long (1.5″)
33-W
Open (DNI) or 50-W
2 pF
50-W or Hi-Z
1900K
Short
33-W
50-W
2 pF
Hi-Z
Figure 8. Differential Outputs Schematic Configuration: Long (OUT6) vs. Short (OUT7) Metal Traces
HCSL Output Measurement
Misc. Pins
HCSL outputs are typically terminated with 50-W to
ground. Measuring HCSL outputs can be easily
accomplished by:
FB_OUT & FB_OUT# − External Termination of
Feedback Pins
FB_OUT & FB_OUT# have convenient “test point
anvils” to monitor these pins with Hi-Z probe.
NB3N1900K (HCSL): Since the FB_OUT & FB_OUT#
pins do not drive transmission lines (no SMAs), the board
layout has these pins loaded/terminated at the DUT per
datasheet; 83-W to GND is installed for the 100-W board.
NB3N1900K (HCSL Outputs) − 50-W Oscilloscope Head
With RP removed from board, connect the HCSL outputs
through the SMA connectors to the 50-W internal impedance
of the oscilloscope sampling head.
NB3N1900K (HCSL Outputs) − Use Hi-Z Probe
With RP installed, use a high-impedance probe on the
output’s metal trace. Holes for headers to connect to Hi-Z
probes are available, but the header pins are not installed.
• Single-ended Hi-Z Probes or,
• Differential Hi-Z Probe;
IREF Pin
NB3N1900K (HCSL): The RREF resistor (R99) to GND is
for the HCSL output part device.
RREF = 475-W is installed for the 100-W board.
http://onsemi.com
5
NB3N1900KMNGEVB
In order to enable the I2C control of the DUT, header
jumpers J27 & J28 must be shorted.
The I2C/SMBus interface circuitry is powered separately
from the USB type-B connection and is isolated from
device VDD and VDDIO.
The SDA and SCL pins can also be externally accessed by
an off-board programmer, allowing other SMBus emulators
to be used to program the DUT. If used, remove both jumpers
J27 & J28. “Test-point anvils” TP33 & TP34 are available
for external control of the device with the use with
mini-grabber cables.
To receive the GUI software and GUI software manual
please contact below:
Graphical User Interface (GUI)
USB & I 2C/SMBus Interface
The NB3N1900K EVB has an on-board I2C/SMBus
interface circuitry located in the upper left section of the
board.
This circuitry will interface with the software program
and the device via the SDA and SCL input pins, and can
control all twelve of the OE_n# pins, PLL Mode and
Frequency Select directly from the GUI.
SCL & SDA
The SMBus Clock (SCL) and Data (SDA) pins are
exercised through the on-board I2C interface.
http://onsemi.com
6
NB3N1900KMNGEVB
QUICK START LAB SET-UP USER’S GUIDE
Pre-Power-Up
Table 2. POWER SUPPLY CONNECTIONS
1. Connect power supply cables to VDD, VDDIO
and GND banana jacks; (do not turn power on,
yet).
2. Connect a signal generator to the SMA connectors
for the CLK_IN & CLK_IN# inputs.
3. 50-W termination resistors are installed for a signal
generator on the board. Set appropriate input
signal levels; (HCSL input, VIL = 0 V,
VIH = 700 mV, Frequency 100.00 or
133.33 MHz).
4. Ensure the PWRGD/PWRDN# pin is in the Low
state before power up (PWRDN#). There is
a jumper on pin 6 to easily select between High
and Low. See Figure 7.
5. The 100M_133M# and HBW_BYP_LBW pins
need to be hardware selected with jumpers.
See Figures 3 and 6.
6. Connect the DIF_n/DIF_n# outputs to the
appropriate oscilloscope.
Device Pin
Power Supply Connector
Power Supply
VDD, VDDIO
VCC = +3.3 V
GND
0V
Single Power Supply
+3.3 V
0V
VDD, VDDIO
+3.3 V
GND
Figure 9. Power Supply Connections
Signal Generator
Oscilloscope
OUT
OUTb
IN
0V
3.3 V
3.3 V
INb
Figure 10. Typical Lab Test Set-Up
Power-Up Sequence
Optional
1. Turn on power supply, 3.3 V (VDD & VDDIO)
2. Move PWRGD/PWRDN# jumper from Low to
logic High, PWRGD position
3. Turn on the Differential Clock Signal for the
CLK_IN inputs
4. Monitor DIF_n/DIF_n# outputs on oscilloscope
Graphical User Interface
There is a stand-alone Graphical User Interface software
package and user’s manual that will interface with the DUT
via the USB connector.
1. Connect the USB port on the evaluation board to
a USB port on the PC via cable.
2. See the stand-alone GUI instructions document.
3. Allow Windows to install the necessary drivers for
the eval board USB interface hardware.
4. Start the GUI program.
http://onsemi.com
7
NB3N1900KMNGEVB
Table 3. BILL OF MATERIALS FOR THE NB3N1900KMNGEVB
Ref. Des.
Qty
Part#
Value
B1
1
C1−C35,
C37, C42,
C43
38
C1005C0G1H020C
2.0 pF
C36, C44
2
TR3A106K010C2000
C38, C40,
C67, C68
4
C39, C41,
C46−C54,
C56−C58,
C60, C62,
C65, C69
PCB Footprint
Vendor
Vendor PN
HiQ Electronics
NB3N1900KMNGEVB
C0402
Digi-Key
445-4863-1-ND
TDK
10 mF
C1206
Digi-Key
718-1300-1-ND
Vishay
GRM155R61A105ME15D
1 mF
C0402
Digi-Key
490-5409-1-ND
Murata
18
0402ZD104KAT2A
100 nF
C0402
Digi-Key
478-1129-1-ND
AVX
PC Board,
Clock Fanout
Board
Manufacturer
C45
1
C1608X5R1A106M
10 mF
C0603
Digi-Key
445-6853-1-ND
TDK
C55, C59,
C61
3
C1005X5R0J475M
4.7 mF
C0402
Digi-Key
445-7395-1-ND
TDK
C63
1
0402YC103KAT2A
10 nF
C0402
Digi-Key
478-1114-1-ND
AVX
C64, C66
2
GRM1555C1H100JZ01D
10 pF
C0402
Digi-Key
490-1278-1-ND
Murata
D1
1
PACDN004SR
PACDN004
SOT_143
Mouser
748-PACDN004SR
ON Semiconductor
FB1, FB2
2
BLM18KG601SN1D
600
L0603
Digi-Key
490-5258-1-ND
Murata
FB3, FB4
2
BLM15AG601SN1D
600
L0402
Digi-Key
490-1006-1-ND
Murata
H1, H2, H3,
H4
4
.129 Hole in
.240 Round
Pad
HOLE_0.240R0.12
9_PTH
J1−J4, J6, J7,
J10, J11, J13,
J14, J15, J17,
J20, J22
14
142-0701-801
SMA Jack, End
Launch
SMA_Jack_End_L
aunch
Digi-key
J502-ND
Johnson
Components
J5, J8, J9,
J12, J16, J18,
J19, J21, J23
9
961103-6404-AR
Header 3-pin
HDR_1X3_2P54
Digi-Key
3M9448-ND
3M
J24
1
571-0500
Banana Jack,
Thru-Hole, Red
con_571-0500
Mouser
164-6219
Deltron
J25
1
571-0700
Banana Jack,
Thru-Hole,
Yellow
con_571-0500
Mouser
164-7170
Deltron
J26
1
571-0100
Banana Jack,
Thru-Hole,
Black
con_571-0500
Mouser
164-6218
Deltron
J27, J28
2
961102-6404-AR
Header 2-pin
HDR_1X2_2P54
Digi-Key
3M9447-ND
3M
J29
1
USB-B1SMHSW6
Conn, USB−B,
SMT
Con_USB_B_RA
Digi-Key
ED2994-ND
On Shore
Technology
LED_0603
LED1
1
LTST-C190KGKT
LED, Green
Digi-Key
160-1435-1-ND
Lite-On
M1−M8, M10
9
QPC02SXGN-RC
Shunt
Digi-Key
S9337-ND
Sullins
M9,
M11−M13
4
1808
Standoff,
4−40 1/4 × 5/8
Digi-Key
1808K-ND
Keystone
M14−M17
4
PMS 440 0025 PH
Screw, 4−40 ×
0.25, PHP
Digi-Key
H342-ND
Building Fasteners
PR1−PR6
6
No Part
4 Round Pads,
.060 with
.040 Hole
BERG_2X2_2P54
http://onsemi.com
8
NB3N1900KMNGEVB
Table 3. BILL OF MATERIALS FOR THE NB3N1900KMNGEVB (continued)
Ref. Des.
Qty
R1, R2, R5,
R6, R10, R11,
R14, R18,
R19, R22,
R25, R27,
R30, R31,
R32, R34,
R37, R39,
R41, R43,
R45, R48,
R51, R53,
R55, R58,
R61, R65,
R69, R72,
R75, R77,
R79, R83,
R88, R92,
R95, R97
Part#
Value
PCB Footprint
Vendor
Vendor PN
Manufacturer
38
33 W
R0402
Digi-Key
P33JTR-ND
Panasonic
R3, R7, R16,
R20, R23,
R28, R33,
R35
8
49.9 W
R0402
Digi-Key
P49.9LCT-ND
Panasonic
R4, R8, R17,
R21, R24,
R26, R29,
R36, R38,
R40, R42,
R44, R47,
R50, R52,
R54, R57,
R60, R62,
R66, R71,
R74, R76,
R78, R82,
R87, R90,
R94, R96,
R98
30
49.9 W
R0402
Digi-Key
P49.9LCT-ND
Panasonic
R9, R12,
R13, R15,
R46, R49,
R56, R59,
R70, R73,
R80, R84
12
CRCW04020000Z0ED
0W
R0402
Digi-Key
541-0.0JCT-ND
Vishay
R63, R64
2
ERJ-3EKF49R9V
49.9 W
R0603
Digi-Key
P49.9HCT-ND
Panasonic
R67, R68,
R85, R89
4
ERJ-3GEYJ472V
4.7 kW
R0603
Digi-Key
P4.7KGCT-ND
Panasonic
R81, R86
2
ERJ-3GEYJ472V
4.7 kW
R0603
Dig-Key
P4.7KGCT-ND
Panasonic
R91, R93
2
ERJ-3GEYJ2R2V
2.2 W
R0603
Digi-Key
P2.2GCT-ND
Panasonic
R99
1
ERJ-2RKF4120X
475 W
R0402
Digi-Key
P412LCT-ND
Panasonic
R100, R102
2
ERJ-2GE0R00X
0W
R0402
Digi-Key
P0.0JCT-ND
Panasonic
R101, R103
2
ERJ-2RKF69R8X
82.5 W
R0402
Digi-Key
P69.8LCT-ND
Panasonic
R104−R106,
R108−R110
6
ERJ-2GEJ103X
10 kW
R0402
Digi-Key
P10KJCT-ND
Panasonic
R107
1
ERJ-2RKF1202X
12 kW
R0402
Digi-Key
P12.0KLCT-ND
Panasonic
R111
1
ERJ-2GEJ471X
470 W
R0402
Digi-Key
P470JCT-ND
Panasonic
R112
1
ERJ-2GEJ222X
2.2 kW
R0402
Digi-Key
P2.2KJCT-ND
Panasonic
SG1−SG12
12
No Part
Solder Gap
R0201
TP1−TP22,
TP24, TP26,
TP28, TP29
26
Test Pad
30 × 30 mil
tp_30_30
TP23, TP25,
TP27,
TP30−TP34
8
5015
Test Point, SMT
tp_70_135
Digi-Key
5015KCT-ND
Keystone
TP35, TP36
2
No Part
Test Pad
30 × 60 mil
tp_30_60
TP37−TP40
4
No Part
Test Pad
50 × 100 mil
tp_50_100
U1
1
NB3N1900KMNG
DNI
NB3N1900K
QFN_72P_0P5MM
−
−
ON Semiconductor
http://onsemi.com
9
NB3N1900KMNGEVB
Table 3. BILL OF MATERIALS FOR THE NB3N1900KMNGEVB (continued)
Ref. Des.
Qty
Part#
Value
PCB Footprint
Vendor
U2
1
FT2232HQ-REEL
U3
1
93LC46BT-I/ST
U4
1
Y1
1
Vendor PN
Manufacturer
FT2232H
QFN_64_0p5
Digi-Key
768-1025-1-ND
FTDI
93LC46B
TSSOP_8_4p4W_
0P65
Digi-Key
93LC46BT-I/STCT-ND
Microchip
NCP4586DSN33T1G
NCP4586,
3.3 V
SOT23_5p
ON Semiconductor
NCP4586DSN33T1G
ON Semiconductor
ABM8G-12.000MHZ-4Y-T3
12 MHz
Cry-4p-SMD1
Digi-Key
535-10901-1-ND
Abracon Corp
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
10
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
EVBUM2256/D