ZigBit 2.4GHz Amplified Wireless Modules RevB - Preliminary

ZIGBIT 2.4GHZ AMPLIFIED WIRELESS
MODULES REVB
ATZB-A24-UFLB/U0B
DATASHEET
Features
•
•
•
•
•
Ultra compact size (38.0 × 13.5 × 2.0mm)
High RX sensitivity (-107dBm)
Outperforming link budget (up to 127dB)
Up to +20dBm output power
Very low power consumption:
• 30µA in sleep mode (2)
• 39.5mA in RX mode (1)
• 183.5mA in TX mode (1)
•
•
Ample memory resources (128KB of flash memory, 8KB RAM, 4KB EEPROM)
Wide range of interfaces (both analog and digital)
• Nine spare GPIO, two spare IRQ lines
• Four ADC lines + one line for supply voltage control (up to nine lines with JTAG
•
•
•
•
•
Notes:
disabled)
UART with CTS/RTS control
USART
I2 C
1-wire
Up to 30 lines configurable as GPIO
•
•
•
•
•
•
•
IEEE® 802.15.4 compliant transceiver
•
•
•
Mesh networking capability
2.4GHz ISM band
Extended range through additional PA and LNA
Ultra-low power consumption combined with unprecedented range
Rapid design-in with built-in U.FL connector (ATZB-A24-UFLB)
Flexibility in using a different external antenna for every application
Small physical footprint and low profile for optimum fit in even the smallest of
devices
Single source of support for HW and SW
Worldwide license-free operation
1.
Measured with LNA gain enabled / measured with TX output power of +20dBm; measured with MCU clock of
8MHz.
2.
Refer the Known Issues section.
42058C−WIRELESS−06/2013
Table of Contents
1. Introduction .......................................................................................... 3 1.1 Summary ........................................................................................................... 3 1.2 Applications ....................................................................................................... 3 2. Abbreviations and Acronyms ............................................................... 4 3. Related Documents ............................................................................. 5 4. ZigBit Module Overview ....................................................................... 6 4.1 Overview ........................................................................................................... 6 5. Specifications ....................................................................................... 7 5.1 Electrical Characteristics ................................................................................... 7 5.1.1 Absolute Maximum Ratings ................................................................ 7 5.1.2 Test Conditions ................................................................................... 7 5.1.3 RF Characteristics .............................................................................. 8 5.1.4 Atmel ATmega1281V Microcontroller Characteristics ......................... 8 5.1.5 Module Interfaces Characteristics ....................................................... 9 5.2 Physical/environmental Characteristics and Outline ......................................... 9 5.3 Pin Configuration............................................................................................. 10 5.4 Mounting Information ...................................................................................... 13 5.5 Soldering Profile .............................................................................................. 14 5.6 Product Design Considerations ....................................................................... 14 5.7 Internal Schematics......................................................................................... 16 6. Ordering Information .......................................................................... 17 7. Agency Certification ........................................................................... 18 7.1 United States (FCC) ........................................................................................ 18 7.2 Using Limited Modular certified products ........................................................ 18 7.3 European Union (ETSI) ................................................................................... 18 8. Revision History ................................................................................. 20 9. Known Issues ..................................................................................... 21 ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
2
1.
Introduction
1.1
Summary
ZigBit® Amp is an ultra-compact, extended range, low-power, and high-sensitivity 2.4GHz IEEE 802.15.4/ZigBee® OEM
module from Atmel®. Based on the innovative mixed-signal hardware platform from Atmel, this module is enhanced by
an LNA, PA integrated front end, and is designed for wireless sensing, monitoring, and control and data acquisition
applications. ZigBit Amp modules eliminate the need for costly and time-consuming RF development, and shorten timeto-market for wireless applications with extended range requirements.
Two different versions of ZigBit 2.4GHz Amplified modules are available: the ATZB-A24-UFLB with built-in U.FL
antenna connector, and the ATZB-A24-U0B with unbalanced 50Ω RF output.
1.2
Applications
The ZigBit module is compatible with robust IEEE 802.15.4/ZigBee stack that supports a self-healing, self-organizing
mesh network, while optimizing network traffic and minimizing power consumption. Atmel offers two stack
configurations; BitCloud and SerialNet. BitCloud is a ZigBee PRO certified software development platform supporting
reliable, scalable, and secure wireless applications running on Atmel ZigBit modules. SerialNet allows programming of
the module via a serial AT-command interface.
The applications include, but are not limited to:
•
Building automation and monitoring
•
•
•
•
•
•
•
•
Lighting controls
•
Wireless smoke- and CO-detectors
•
Structural integrity monitoring
HVAC monitoring and control
Inventory management
Environmental monitoring
Security
Water metering
Industrial monitoring
•
Machinery condition and performance monitoring
•
Monitoring of plant system parameters such as temperature, pressure, flow, tank level, humidity,
vibration, etc.
Automated meter reading (AMR)
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
3
2.
Abbreviations and Acronyms
ADC
Analog-to-Digital Converter
API
Application Programming Interface
DC
Direct Current
DTR
Data Terminal Ready
EEPROM
Electrically Erasable Programmable Read-Only Memory
ESD
Electrostatic Discharge
GPIO
General Purpose Input/Output
HAF
High Frequency
HVAC
Heating, Ventilating, and Air Conditioning
HW
Hardware
I2C
Inter-Integrated Circuit
IEEE
Institute of Electrical and Electronics Engineers
IRQ
Interrupt Request
ISM
Industrial, Scientific and Medical radio band
JTAG
Digital interface for debugging of embedded device, also known as IEEE 1149.1 standard
interface
MAC
Medium Access Control layer
MCU
Microcontroller Unit. In this document it also means the processor, which is the core of a ZigBit
module
NRE
Network layer
OEM
Original Equipment Manufacturer
OTA
Over-The-Air upgrade
PA
Power Amplifier
PCB
Printed Circuit Board
PER
Package Error Ratio
RAM
Random Access Memory
RF
Radio Frequency
RTS/CTS
Request to Send/ Clear to Send
RX
Receiver
SMA
Surface Mount Assembly
SPI
Serial Peripheral Interface
SW
Software
TTM
Time-To-Market
TX
Transmitter
UART
Universal Asynchronous Receiver/Transmitter
USART
Universal Synchronous/Asynchronous Receiver/Transmitter
USB
Universal Serial Bus
ZigBee, ZigBee PRO Wireless networking standards targeted at low-power applications
802.15.4
The IEEE 802.15.4-2003 standard applicable to low-rate wireless Personal Area Network
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
4
3.
Related Documents
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
ZigBit 2.4GHz Wireless Modules ATZB-24-B0/A2. Product datasheet. Atmel doc8226.pdf
ZigBit 700/800/900MHz Wireless Modules ATZB-900-B0. Product datasheet. Atmel doc8227.pdf
ZigBit 2.4 GHz Amplified Wirelss Modules ATZB-A24-UFL/U0. Atmel doc8228.pdf
Atmel 8-bit AVR® Microcontroller with 64K/128K/256K Bytes In-System Programmable Flash. Atmel
doc2549.pdf
Atmel Low-Power Transceiver for ZigBee Applications. AT86RF230 datasheet. Atmel doc5131.pdf
Ultra Small Surface Mount Coaxial Connectors - Low Profile 1.9mm or 2.4mm Mated
Height. http://www.hirose.co.jp/cataloge_hp/e32119372.pdf
IEEE Std 802.15.4-2003 IEEE Standard for Information technology - Part 15.4 Wireless Medium Access
Control (MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks (LRWPANs)
ZigBee Specification. ZigBee Document 053474r17, October 19, 2007
BitCloud IEEE 802.15.4/ZigBee Software. AVR2050: BitCloud Developer Guide. Atmel doc8199.pdf
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
5
4.
ZigBit Module Overview
4.1
Overview
The ZigBit Amp is an extended-range, low-power, high sensitivity IEEE 802.15.4/ZigBee OEM module. Based on a solid
combination of the latest Atmel MCU Wireless hardware platform, power amplifier, and low-noise amplifier, the ZigBit
Amp offers an unmatched combination of superior radio performance, ultra-low power consumption and exceptional
ease of integration.
Figure 4-1. ATZB-A24-UFLB/U0B Block Diagram.
ZigBit Amp modules contain the Atmel ATmega1281V Microcontroller [4] and AT86RF230 RF Transceiver [5]. The
module features 128KB flash memory and 8KB RAM.
The compact all-in-one chip integration of output Power Amplifier and input Low-Noise Amplifier, along with RF switches
enables digital control of an external RF front-end to dramatically improve the ZigBit's range performance on signal
transmission and increases its sensitivity. This ensures stable connectivity within a larger coverage area, without a
significant increase in module size. The HF U.FL coaxial connector [6] used in the ATZB-A24-UFLB module enables the
user to choose an appropriate external antenna for every type of application.
ZigBit Amp already contains a complete RF/MCU design with all the necessary passive components included. The
module can be easily mounted on a simple 2-layer PCB with a minimum of required external connection. Compared to a
custom RF/MCU solution, a module-based solution offers considerable savings in development time and NRE cost per
unit during the design, prototyping, and mass production phases of product development.
All ZigBits are preloaded with a Bootloader when they are sold as Modules, either in Single units or T&R.
Depending on end-user design requirements, the ZigBit Amp can operate as a self-contained sensor node, where it
would function as a single MCU, or it can be paired with a host processor driving the module over a serial interface. In
the former case, a user application may be used with the BitCloud software allowing customization of embedded
applications through BitCloud's C API.
In the latter case, the host processor controls data transmission and manages module peripherals via an extensive set
of SerialNet AT commands. Thus, no firmware customization is required for a successful module design-in. Additionally,
third-party sensors can be connected directly to the module, thus expanding the existing set of peripheral interfaces.
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
6
5.
Specifications
5.1
Electrical Characteristics
5.1.1
Absolute Maximum Ratings
Table 5-1.
Parameter
Minimum
Maximum
Voltage on any pin with respect to ground
-0.5V
VCC + 0.5V
DC current per I/O pin
40mA
DC current DVCC and DGND pins
300mA
Input RF level
+5dBm
Notes:
5.1.2
Absolute Maximum Ratings (1)(2).
1.
Absolute Maximum Ratings are the values beyond which damage to the device may occur. Under no
circumstances must the absolute maximum ratings given in Table 5-1 be violated. Stresses beyond those
listed under "Absolute Maximum Ratings" may cause permanent damage to the device.
This is a stress rating only. Functional operation of the device at these or other conditions, beyond those
indicated in the operational sections of this specification, is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
2.
Attention! The ZigBit Amp is an ESD-sensitive device. Precaution should be taken when handling the
device in order to prevent permanent damage.
Test Conditions
Table 5-2.
Test Conditions (unless otherwise stated), F = 2.45GHz, VCC = 3V, Tamb = 25°C.
Parameter
Supply voltage, VCC
Current consumption: RX mode
(1)
Current consumption: TX mode
(1)
Current consumption: Power-save mode
Note:
(1)
Range
Unit
3.0 to 3.6
V
39.5
mA
183.5
mA
30
(2)
µA
1.
The parameters are measured under the following conditions:
a) RMS, BitCloud Software is running at 8MHz clock rate, DTR line management is turned off.
b) All interfaces are set to the default state (see Table 5-9 Pin Descriptions.)
c) Output TX power (when measuring consumption in TX mode) is +20dBm.
d) JTAG is not connected.
e) LNA gain enabled when measuring consumption in RX mode.
2.
Refer the Known Issues section.
Current consumption actually depends on multiple factors, including but not limited to, the board design and materials,
BitCloud settings, network activity, EEPROM read/write operations. It also depends on MCU load and/or peripherals
used by an application.
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
7
5.1.3
RF Characteristics
Table 5-3.
RF Characteristics.
Parameters
Condition
Range
Unit
Frequency band
2.4000 to 2.4835
GHz
Numbers of channels
16
Channel spacing
5
Transmitter output power
Adjusted in 5 steps
+7 to +20
Receiver sensitivity
PER = 1%
-101
On-air data rate
dBm
250
Kbps
TX output/ RX input nominal impedance
Unbalanced output
50
Ω
Range (open field, LoS, elevated)
With external 2.2dBi antenna
Up to 4000
m
Table 5-4.
TX Power Settings – United States.
Register Value
Power Register Setting [dBm]
Output Power [dBm] (at antenna feed)
11
-5.2
+20
12
-7.2
+18
13
-9.2
+16
14
-12.2
+12
15
-17.2
+7
Table 5-5.
5.1.4
MHz
TX Power Settings – European Union.
Register Value
Power Register Setting [dBm]
Output Power [dBm] (at antenna feed)
15
-17.2
+7
Atmel ATmega1281V Microcontroller Characteristics
Table 5-6.
ATmega1281V Characteristics.
Parameters
Condition
Range
Unit
On-chip flash memory
128K
Bytes
On-chip RAM size
8K
Bytes
On-chip EEPROM size
4K
Bytes
Operation frequency
8
MHz
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
8
5.1.5
Module Interfaces Characteristics
Table 5-7.
Module Interfaces Characteristics.
Parameters
Condition
Range
Unit
38.4
kbps
10/200
Bits/µs
ADC input resistance
>1
MΩ
ADC reference voltage (VREF)
1.0 to VCC - 3
ADC input voltage
0 – VREF
I2C maximum clock
400
kHz
2.3/0.5
V
32.768
kHz
UART maximum baud rate
ADC resolution conversion time
In single conversion mode
GPIO output voltage (high/low)
-10/+5mA
Real-time oscillator frequency
5.2
V
Physical/environmental Characteristics and Outline
Table 5-8.
Module Interfaces Characteristics.
Parameters
Value
Comments
Size
38.0 × 13.5 × 2.0mm
ATZB-A24-UFLB/U0B
Normal operating temperature range
-20°C to +70°C
Extended operating temperature range
-40°C to +85°C operational
Operating relative humidity range
No more than 80%
Note:
1.
Safe range
(1)
Degraded range
Minor degradation of clock stability may occur.
Figure 5-1. Atmel ATZB-A24-UFLB/U0B Mechanical Drawing.
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
9
5.3
Pin Configuration
Figure 5-2. Atmel ATZB-A24-UFLB Pinout.
Figure 5-3. Atmel ATZB-A24-U0B Pinout.
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
10
Table 5-9.
Pin Descriptions.
Connector Pin
Pin Name
Description
1
SPI_CLK
Reserved for stack operation (4)
2
3
4
5
6
7
SPI_MISO
SPI_MOSI
GPIO0
GPIO1
GPIO2
OSC32K_OUT
I/O
Reserved for stack operation
(4)
Reserved for stack operation
(4)
Default State
After Power On
O
I/O
I/O
General purpose digital input/output 0
(2)(3)(4)(7)
I/O
tri-state
General purpose digital input/output 1
(2)(3)(4)(7)
I/O
tri-state
General purpose digital input/output 2
(2)(3)(4)(7)
I/O
tri-state
32.768kHz clock output
(4)(5)
(4)
O
8
RESET
Reset input (active low)
9, 22, 23
DGND
Digital ground
10
CPU_CLK
RF clock output. When module is in active state, 8MHz signal is
present on this line. While module is in the sleeping state, clock
generation is also stopped (4). This pin is a test point and not to be
used to clock External devices
O
11
I2C_CLK
I2C Serial clock output (2)(3)(4)(7)
O
tri-state
I/O
tri-state
I
tri-state
O
tri-state
12
13
I2C_DATA
UART_TXD
2
I C Serial data input/output
(2)(3)(4)(7)
UART receive input to ZigBit MCU
(1)(2)(3)(4)(7)
(1)(2)(3)(4)(7)
14
UART_RXD
UART transmit output from ZigBit MCU
15
UART_RTS
RTS input (request to send) for UART hardware flow control. Active
low (2)(3)(4)(7)
I
tri-state
16
UART_CTS
CTS output (clear to send) for UART hardware flow control. Active
low (2)(3)(4)(7)(8)
O
tri-state
17
GPIO6
General purpose digital input/output 6 (2)(3)(4)(7)
I/O
tri-state
GPIO7
General purpose digital input/output 7
(2)(3)(4)(7)
I/O
tri-state
General purpose digital input/output 3
(2)(3)(4)(7)
I/O
tri-state
General purpose digital input/output 4
(2)(3)(4)(7)
I/O
tri-state
General purpose digital input/output 5
(2)(3)(4)(7)
I/O
tri-state
18
19
20
21
GPIO3
GPIO4
GPIO5
(9)
24, 25
D_VCC
Digital Supply Voltage (VCC)
26
JTAG_TMS
JTAG Test Mode Select (2)(3)(4)(6)
27
28
29
30
31
JTAG_TDI
JTAG_TDO
JTAG_TCK
ADC_INPUT_3
ADC_INPUT_2
JTAG Test Data Input
JTAG Test Data Output
JTAG Test Clock
I
(2)(3)(4)(6)
I
(2)(3)(4)(6)
O
(2)(3)(4)(6)
I
ADC Input Channel 3
(2)(3)(7)
I
tri-state
ADC Input Channel 2
(2)(3)(7)
I
tri-state
(2)(3)(7)
I
tri-state
32
ADC_INPUT_1
ADC Input Channel 1
33
BAT
ADC Input Channel 0, used for battery level measurement. This pin
equals VCC/3 (2)(3)(7)
I
tri-state
34
A_VREF
Input/Output reference voltage for ADC
I/O
tri-state
35
AGND
Analog ground
36
GPIO9/1_WR
General purpose digital input/output 9 / 1-wire interface (2)(3)(4)(7)
I/O
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
11
37
UART_DTR
38
USART0_RXD
39
USART0_TXD
DTR input (Data Terminal Ready) for UART. Active low (2)(3)(4)(7)
USART/SPI Receive pin
(2)(3)(4)(7)
USART /SPI Transmit pin
(2)(3)(4)(7)
(2)(3)(4)(7)(11)
40
USART0_EXTCLK
USART/SPI External Clock
41
GPIO8
General Purpose Digital Input/Output
42
IRQ_7
tri-state
O
tri-state
I/O
tri-state
tri-state
Digital Input Interrupt request 7
I
tri-state
(2)(3)(4)(7)
I
tri-state
Digital Input Interrupt request 6
44, 45, 51, 52,
53, 56, 57
DGND
Digital ground
46, 47
NC
Not connected
48, 50
RF GND
RF analog ground (2)(3)(4)(7)
49
RFP_IO
RF Input/Output (10)
Notes:
I
I/O
IRQ_6
VTT
tri-state
(2)(3)(4)(7)
43
54, 55
I
Transmitter supply voltage
I/O
(9)
1.
The UART_TXD pin is intended for input (that is, its designation as "TXD" implies some complex system containing
ZigBit as its RF terminal unit), while UART_RXD pin, vice versa, is for output.
2.
Most of pins can be configured for general purpose I/O or for some alternate functions as described in details in the
Atmel ATmega1281V Datasheet [3].
3.
GPIO pins can be programmed either for output, or for input with/without pull-up resistors. Output pin drivers are
strong enough to drive LED displays directly (refer to figures on pages 387-388, [3]).
4.
All digital pins are provided with protection diodes to D_VCC and DGND.
5.
It is strongly recommended to avoid assigning an alternate function for OSC32K_OUT pin because it is used by
BitCloud.
6.
Normally, JTAG_TMS, JTAG_TDI, JTAG_TDO, JTAG_TCK pins are used for on-chip debugging and flash burning.
They can be used for A/D conversion if JTAGEN fuse is disabled.
7.
The following pins can be configured with the BitCloud software to be general-purpose I/O lines: GPIO0, GPIO1,
GPIO2, GPIO3, GPIO4, GPIO5, GPIO6, GPIO7, GPIO8, GPIO_1WR, I2C_CLK, I2C_DATA, UART_TXD,
UART_RXD, UART_RTS, UART_CTS, ADC_INPUT_3, ADC_INPUT_2, ADC_INPUT_1, BAT, UART_DTR,
USART0_RXD, USART0_TXD, USART0_EXTCLK, IRQ_7, IRQ_6. Additionally, four JTAG lines can be
programmed with software as GPIO as well, but this requires changing the fuse bits and will disable JTAG
debugging.
8.
With BitCloud, CTS pin can be configured to indicate sleep/active condition of the module thus providing
mechanism for power management of the host processor. If this function is necessary, a connection of this pin to an
external pull-down resistor is recommended to prevent the undesirable transients during the module reset process.
9.
Using ferrite bead and 1µF capacitor located closely to the power supply pin is recommended, as shown below:
3.0V ... 3.6V
D_VCC
DGND
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
12
10. Pins 48, 49 and 50 are featured for the Atmel ATZB-A24-U0B module only.
NOTE: TXD, RXD of UART are crossed inside ZigBit Module. External UART devices connecting to ZigBit Module
should follow straight connection for UART.
UART_TXD_external_device <-> UART_TXD
UART_RXD_external_device <-> UART_RXD
11. In SPI mode, USART0_EXTCLK is output. In USART mode, this pin can be configured as either input or output pin.
5.4
Mounting Information
Figure 5-4 shows the PCB layout recommended for a ZigBit Amp module. Neither via-holes nor wires are allowed on
the PCB upper layer in the area occupied by the module. As a critical requirement, RF_GND pins should be grounded
via several via-holes to be located right next to the pins thus minimizing inductance and preventing both mismatch and
losses.
The ZigBit Modules are fixed with an EMI Shield to ensure compliance to Emission and Immunity rules. This shield is
galvanic and NOT air tight. Cleaning of the module with IPA / other similar agents is not advised. Humidity protection
coating (conformal) will cause deviated RF behavior and coating material being trapped inside EMI Shield. So this
should be avoided. For products requiring conformal coating, it is advised to suitably mask the ZigBit before applying
the coating to rest of the ZigBit carrier board. To protect ZigBit from humidity, the housing of the product should ensure
suitable Ingress Protection standards are complied with.
The UFL connector should never be exposed to Varnish / similar conformal coating material which will affect electrical
connection between the surfaces of UFL Connector and Antenna / Antenna cable connector.
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
13
Figure 5-4. Atmel ATZB-A24-UFL/U0 PCB Recommended Layout, Top View.
5.5
Soldering Profile
The J-STD-020C-compliant soldering profile is recommended according to Table 5-10.
Table 5-10. Soldering Profile (1).
Profile Feature
Green Package
Average ramp-up rate (217°C to peak)
3°C/s max.
Preheat temperature 175°C ±25°C
180s max.
Temperature maintained above 217°C
60s to 150s
Time within 5°C of actual peak temperature
20s to 40s
Peak temperature range
260°C
Ramp-down rate
6°C/s max.
Time within 25°C to peak temperature
8 minutes
Note:
5.6
1.
The package is backward compatible with PB/Sn soldering profile.
Product Design Considerations
Multiple factors affect proper antenna match, hence, affecting the antenna pattern. The particular factors are the board
material and thickness, shields, the material used for enclosure, the board neighborhood, and other components
adjacent to antenna.
General recommendations:
•
•
•
Metal enclosure should not be used. Using low profile enclosure might also affect antenna tuning
Placing high profile components next to antenna should be avoided
Having holes/vias punched around the periphery of the board eliminates parasitic radiation from the board
edges also distorting antenna pattern
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
14
•
ZigBit Amp module should not be placed next to consumer electronics which might interfere with ZigBit Amp's
RF band frequency
The board design should prevent propagation of microwave field inside the board material. Electromagnetic waves of
high frequency may penetrate the board thus making the edges of the board radiate, which may distort the antenna
pattern. To eliminate this effect, metalized and grounded holes/vias must be placed around the board's edges.
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
15
5.7
Internal Schematics
Figure 5-5. Internal Schematics.
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
16
6.
Ordering Information
Table 6-1.
Ordering Information.
Part Number
Description
ATZB-A24-UFLBR
2.4GHz IEEE802.15.4/ZigBee power amplified OEM module with U.FL antenna connector - RevB,
tape and reel
ATZB-A24-UFLB
2.4GHz IEEE802.15.4/ZigBee power amplified OEM module with U.FL antenna connector -RevB,
single unit
ATZB-A24-U0BR
2.4GHz IEEE802.15.4/ZigBee power amplified OEM module with unbalanced RF output –RevB,
tape and reel
ATZB-A24-U0B
2.4GHz IEEE802.15.4/ZigBee power amplified OEM module with unbalanced RF output -RevB,
single unit
Note:
Tape and reel quantity: 200.
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
17
7.
Agency Certification
7.1
United States (FCC)
1.
2.
The ATZB-A24-UFLB is certified as Limited modular transmitter with FCC ID VW4A090668.
The ATZB-A24-U0B is certified as Limited modular transmitter with FCC ID VW4A090667.
IMPORTANT: The ATZB-A24-UFLB and ATZB-A24-U0B comply with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation (FCC 15.19).
The internal / external antenna(s) used for this mobile transmitter must provide a separation distance of at least 20cm
from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter.
Installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF
exposure compliance. This device is approved as a mobile device with respect to RF exposure compliance, and may
only be marketed to OEM installers. Use in portable exposure conditions (FCC 2.1093) requires separate equipment
authorization.
IMPORTANT: Modifications not expressly approved by the company could void the user's authority to operate this
equipment (FCC section 15.21).
IMPORTANT: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense
(FCC section 15.105).
7.2
Using Limited Modular certified products
The ATZB-A24-UFLB and ATZB-A24-U0B Zigbit Modules are certified under the Modular certification category of
“Limited Modular transmitter”. Any final end product created using these modules must undergo FCC compliance
testing of the complete final product that includes these modules and receive a new FCC ID assignment for the final
product carrying these modules. Successful certification of the final product lies solely with the type of design of the final
product, excluding the pre- tested Zigbit module.
7.3
European Union (ETSI)
The ATZB-A24-UFLB, ATZB-A24-U0B Modules has been certified for use in European Union countries. If these
modules are incorporated into a product, the manufacturer must ensure compliance of the final product to the European
harmonized EMC and lowvoltage/safety standards. A Declaration of Conformity must be issued for each of these
standards and kept on file as described in Annex II of the R&TTE Directive.
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
18
Furthermore, the manufacturer must maintain a copy of the modules' documentation and ensure the final product does
not exceed the specified power ratings, antenna specifications, and/or installation requirements as specified in the user
manual. If any of these specifications are exceeded in the final product, a submission must be made to a notified body
for compliance testing to all required standards.
IMPORTANT: The 'CE' marking must be affixed to a visible location on the OEM product. The CE mark shall
consist of the initials "CE" taking the following form:
The CE marking must have a height of at least 5mm except where this is not possible on account of the nature of the
apparatus.
The CE marking must be affixed visibly, legibly, and indelibly.
More detailed information about CE marking requirements you can find at "DIRECTIVE 1999/5/EC OF THE
EUROPEAN PARLIAMENT AND OF THE COUNCIL" on 9 March 1999 at section 12.
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
19
8.
Revision History
Doc. Rev.
Date
Comments
42058C
05/2013
Several figures have been replaced
42058B
03/2013
Several corrections made
42058A
12/2012
Initial document release
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
20
9.
Known Issues
Due to a design issue, The ATZB-A24-UFLB, ATZB-A24-U0B modules will consume about 160µ[email protected] in sleep
mode.
ATZB-A24-UFLB/U0B [ZigBit 2.4GHz Amplified Wireless Modules RevB]
42058C−WIRELESS−06/2013
21
Atmel Corporation
Atmel Asia Limited
Atmel Munich GmbH
Atmel Japan G.K.
1600 Technology Drive
Unit 01-5 & 16, 19F
Business Campus
16F Shin-Osaki Kangyo Building
San Jose, CA 95110
BEA Tower, Millennium City 5
Parkring 4
1-6-4 Osaki Shinagawa-ku
USA
418 Kwun Tong Road
D-85748 Garching b. Munich
Tokyo 141-0032
Tel: (+1)(408) 441-0311
Kwun Tong, Kowloon
GERMANY
JAPAN
Fax: (+1)(408) 487-2600
HONG KONG
Tel: (+49) 89-31970-0
Tel: (+81)(3) 6417-0300
www.atmel.com
Tel: (+852) 2245-6100
Fax: (+49) 89-3194621
Fax: (+81)(3) 6417-0370
Fax: (+852) 2722-1369
© 2013 Atmel Corporation. All rights reserved. / Rev.: 42058C−WIRELESS−06/2013
Atmel®, Atmel logo and combinations thereof, AVR®, BitCloud®, Enabling Unlimited Possibilities®, ZigBit®, and others are registered trademarks or trademarks of
Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this
document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES
NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF
INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time
without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in,
automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.