ZIGBIT 2.4GHZ WIRELESS MODULES ATZB-24-A2/B0 DATASHEET Features • Ultra compact size (24 × 13.5 × 2.0mm for the Atmel® ATZB-24-A2 module and 18 × 13.5 × 2.0mm for the Atmel ATZB-24-B0 module) • Innovative balanced dual chip antenna design with antenna gain of approximately 0dBi (A2 only) (for ATZB-24-A2 version) • • • • High RX sensitivity (-101dBm) Outperforming link budget (104dB) Atmel Up to 3dBm output power Very low power consumption: • <6µA in sleep mode • 21.8mA in RX mode • 20.8mA in TX mode (0dBm) • • Ample memory resources (128KB of flash memory, 8KB RAM, 4KB EEPROM) Wide range of interfaces (both analog and digital) • Nine spare GPIO, two spare IRQ lines • Four ADC lines + one line for supply voltage control (up to nine lines with JTAG • • • • • • • • • • disabled) UART with CTS/RTS control USART I2 C 1-wire Up to 30 lines configurable as GPIO Capability to write own MAC address into the EEPROM Optional antenna reference designs IEEE® 802.15.4 compliant receiver 2.4GHz ISM band BitCloud® embedded software, including serial bootloader • Small physical footprint and low profile for optimum fit in even the smallest of devices • • • • • • • • Best-in-class RF link range Extended battery life Easy prototyping with 2-layer PCB Ample memory for user software application Mesh networking capability Easy-to-use low cost evaluation kit Single source of support for HW and SW Worldwide license-free operation 8226C−AVR−07/2013 Table of Contents 1. Introduction .......................................................................................... 3 1.1 Summary ........................................................................................................... 3 1.2 Applications ....................................................................................................... 3 1.3 Abbreviations and Acronyms ............................................................................ 4 1.4 Related Documents........................................................................................... 5 2. ZigBit Module Overview ....................................................................... 6 2.1 Overview ........................................................................................................... 6 3. Specification ......................................................................................... 8 3.1 Electrical Characteristics ................................................................................... 8 3.1.1 Absolute Maximum Ratings ................................................................ 8 3.1.2 Test Conditions ................................................................................... 8 3.1.3 RF Characteristics .............................................................................. 9 3.1.4 Atmel ATmega1281V Microcontroller Characteristics ......................... 9 3.1.5 Module Interfaces Characteristics ....................................................... 9 3.2 Physical / Environmental Characteristics and Outline ....................................... 9 3.3 Pin Configuration............................................................................................. 11 3.4 Mounting Information ...................................................................................... 14 3.5 Sample Antenna Reference Designs .............................................................. 15 3.5.2 General Recommendations .............................................................. 17 3.6 Soldering Profile .............................................................................................. 18 3.7 Internal Schematics......................................................................................... 19 3.8 Handling instructions ....................................................................................... 20 4. Agency Certifications ......................................................................... 21 4.1 United States (FCC) ........................................................................................ 21 4.2 Canada (IC) .................................................................................................... 21 4.3 European Union (ETSI) ................................................................................... 21 4.4 Using Limited Modular Certified Products ....................................................... 22 4.5 Approved Antenna List .................................................................................... 23 5. Ordering Information .......................................................................... 23 6. Revision History ................................................................................. 24 ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 2 1. Introduction 1.1 Summary ZigBit® is an ultra-compact, low-power, high-sensitivity 2.4GHz IEEE 802.15.4/ZigBee® OEM module based on the innovative mixed-signal hardware platform from Atmel. It is designed for wireless sensing, control and data acquisition applications. ZigBit modules eliminate the need for costly and time-consuming RF development, and shorten time-tomarket for a wide range of wireless applications. Two different versions of 2.4GHz ZigBit modules are available: the Atmel ATZB-24-B0 module with balanced RF port for applications where the benefits of PCB or external antenna can be utilized and the Atmel ATZB-24-A2 module with dual chip antenna satisfying the needs of applications that require integrated, small-footprint antenna design. 1.2 Applications ZigBit module is compatible with robust IEEE 802.15.4/ZigBee stack that supports a self-healing, self-organizing mesh network, while optimizing network traffic and minimizing power consumption. Atmel offers two stack configurations: BitCloud and SerialNet. BitCloud is a ZigBee PRO certified software development platform supporting reliable, scalable, and secure wireless applications running on the Atmel ZigBit modules. SerialNet allows programming of the module via serial AT-command interface. The applications include, but are not limited to: • • • • • • • • Building automation and monitoring • Lighting controls • Wireless smoke and CO-detectors • Structural integrity monitoring HVAC monitoring and control Inventory management Environmental monitoring Security Water metering Industrial monitoring • Machinery condition and performance monitoring • Monitoring of plant system parameters such as temperature, pressure, flow, tank level, humidity, vibration, etc. Automated Meter Reading (AMR) ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 3 1.3 Abbreviations and Acronyms ADC Analog-to-Digital Converter AMR Automated Meter Reading API Application Programming Interface DC Direct Current DTR Data Terminal Ready DIP Dual In-line package EEPROM Electrically Erasable Programmable Read-Only Memory ESD Electrostatic Discharge GPIO General Purpose Input/Output HAL Hardware Abstraction Layer HVAC Heating, Ventilating, and Air Conditioning HW Hardware 2 IC Inter-Integrated Circuit IEEE Institute of Electrical and Electronics Engineers IRQ Interrupt Request ISM Industrial, Scientific and Medical radio band JTAG Digital interface for debugging of embedded device, also known as IEEE 1149.1 standard interface MAC Medium Access Control layer MCU Microcontroller Unit. In this document it also means the processor, which is the core of a ZigBit module NWK Network layer OEM Original Equipment Manufacturer OTA Over-The-Air upgrade PCB Printed Circuit Board PER Package Error Ratio PHY Physical layer RAM Random Access Memory RF Radio Frequency RTS/CTS Request to Send/ Clear to Send RX Receiver SMA Surface Mount Assembly SPI Serial Peripheral Interface SW Software TTM Time-To-Market TX Transmitter UART Universal Asynchronous Receiver/Transmitter ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 4 1.4 USART Universal Synchronous/Asynchronous Receiver/Transmitter USB Universal Serial Bus ZDK ZigBit Development Kit ZigBee, ZigBee PRO Wireless networking standards targeted at low-power applications 802.15.4 The IEEE 802.15.4-2003 standard applicable to low-rate wireless Personal Area Network Related Documents [1] Atmel 8-bit AVR® Microcontroller with 64KB/128KB/256KB In-System Programmable Flash. Atmel doc2549.pdf [2] Atmel Low-Power Transceiver for ZigBee Applications. AT86RF230 datasheet. Atmel doc5131.pdf [3] IEEE Std 802.15.4-2003 IEEE Standard for Information technology - Part 15.4 Wireless Medium Access Control (MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks (LR-WPANs) [4] ZigBee Specification. ZigBee Document 053474r17, October 19, 2007 [5] BitCloud® IEEE 802.15.4/ZigBee Software. AVR2050: BitCloud Developer Guide. Atmel doc8199.pdf ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 5 2. ZigBit Module Overview 2.1 Overview ZigBit is a low-power, high-sensitivity IEEE 802.15.4/ ZigBee-compliant OEM module. This multifunctional device occupies less than a square inch of space, which is comparable to a typical size of a single chip. Based on a solid combination of the latest MCU Wireless hardware platform from Atmel, the ZigBit offers superior radio performance, ultra-low power consumption, and exceptional ease of integration. Figure 2-1. Atmel ATZB-24-B0 Block Diagram. VCC(1.8 – 3.6) IRQ UART USART/SPI 2 IC JTAG ANALOG AT86RF230 RF transceiver ATmega1281 SPI Bus GPIO RF I/O . Figure 2-2. Atmel ATZB-24-A2 Block Diagram. VCC(1.8 – 3.6) IRQ UART USART/SPI 2 IC JTAG ANALOG ATmega1281 GPIO AT86RF230 RF transceiver Chip antenna SPI Bus ZigBit modules comply with the FCC (Part 15), IC and ETSI (CE) rules applicable to the devices radiating in an uncontrolled environment. For further details, see Chapter 4. ZigBit fully satisfies the requirements of the “Directive 2002/95/EC of the European Parliament and the Council of 27January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment” (RoHS). Atmel provides fully compliant product in all regions, where the directive is enforced since July 1, 2006. ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 6 The ZigBit contains the Atmel ATmega1281V Microcontroller [1] and the Atmel AT86RF230 RF Transceiver [2]. The module features 128KB Flash memory and 8KB RAM. The ZigBit already contains a complete RF/MCU-related design with all the necessary passive components included. The module can be easily mounted on a simple 2-layer PCB. Compared to a custom RF/MCU design, a module-based solution offers considerable savings in development time and NRE cost per unit during the design, prototyping, and mass production phases of product development. Innovative dual chip antenna design in ATZB-24-A2 module eliminates the balun and achieves good performance over 2.4GHz frequency band. All ZigBits are preloaded with a Bootloader when they are sold as Modules, either in Single units or T&R. Depending on end-user design requirements, a ZigBit module can operate as a self-contained sensor node, where it would function as a single MCU, or it can be paired with a host processor, driving the module over a serial interface. In the former case, a user application may be used with the BitCloud software, allowing customization of embedded applications through BitCloud’s C API. In the latter case, the host processor controls data transmission and manages module peripherals via an extensive set of SerialNet AT commands. Thus, no firmware customization is required for a successful module design-in, additionally; third-party sensors can be connected directly to the module, thus expanding the existing set of peripheral interfaces. ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 7 3. Specification 3.1 Electrical Characteristics 3.1.1 Absolute Maximum Ratings Table 3-1. Notes: 3.1.2 Absolute Maximum Ratings (1)(2) Parameter Minimum Maximum Voltage on any pin, except RESET with respect to ground -0.5V VCC + 5V DC current per I/O pin 40mA DC current DVCC and DGND pins 200mA Input RF level +10dBm 1. Absolute Maximum Ratings are the values beyond which damage to the device may occur. Under no circumstances must the absolute maximum ratings given in this table be violated. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only. Functional operation of the device at these or other conditions, beyond those indicated in the operational sections of this specification, is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2. Attention! ZigBit is an ESD-sensitive device. Precaution should be taken when handling the device in order to prevent permanent damage. Test Conditions Table 3-2. Test Conditions (unless otherwise stated), Vcc = 3V, Tamb = 25°C. Parameter Supply voltage, VCC (2) Current consumption: RX mode Current consumption: TX mode (1) Current consumption: Radio is turned off, MCU is active 50% of the time Current consumption: Power-save mode Notes: (1) (1) Range Unit 1.8 to 3.6 V 21.8 mA 20.8 mA 3.5 mA 6 µA 1. The parameters are measured under the following conditions: a) BitCloud Software is running at 8MHz clock rate, DTR line management is turned off. b) All interfaces are set to the default state (see Pin Assignment Table). c) Output TX power is 0dBm d) JTAG is not connected. 2. Supply voltage below 2.7V requires the MCU to be operating at 2MHz speed. Current consumption actually depends on multiple factors, including but not limited to, the board design and materials, BitCloud settings, network activity, EEPROM read/write operations. It also depends on MCU load and/or peripherals used by an application. ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 8 3.1.3 RF Characteristics Table 3-3. RF Characteristics. Parameter Condition Range Unit Frequency band 2.4000 to 2.4835 GHz Numbers of channels 16 Channel spacing 5 MHz Transmitter output power Adjusted in 16 steps -17 to +3 dBm Receiver sensitivity PER = 1% -101 dBm 250 Kbps 100 Ω Range Unit On-chip flash memory size 128K Bytes On-chip RAM size 8K Bytes On-chip EEPROM size 4K Bytes Operation frequency 8 MHz Range Unit 38.4 Kbps 10/200 Bits/µs ADC input resistance >1 MΩ ADC reference voltage (VREF) 1.0 to VCC -3 V ADC input voltage 0 - VREF V 400 kHz 2.3/ 0.5 V 32.768 kHz On-air data rate TX output/ RX input nominal impedance 3.1.4 Atmel ATmega1281V Microcontroller Characteristics Table 3-4. ATmega1281V Characteristics. Parameter 3.1.5 For balanced output Condition Module Interfaces Characteristics Table 3-5. Module Interfaces Characteristics. Parameter Condition UART maximum baud rate ADC resolution/ conversion time In single conversion mode 2 I C maximum clock GPIO output voltage (high/low) -10/ 5mA Real time oscillator frequency 3.2 Physical / Environmental Characteristics and Outline Table 3-6. Physical / Environmental Characteristics and Outline. Parameter Value Comments 18.8 × 13.5 × 2.0mm ATZB-24-B0 24.0 × 13.5 × 2.0mm ATZB-24-A2 1.3g ATZB-24-B0 1.5g ATZB-24-A2 Operating temperature range -20°C to +70°C -40°C to +85°C operational (1) Operating relative humidity range No more than 80% Size Weight Note: 1. Minor degradation of clock stability may occur. ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 9 Figure 3-1. Atmel ATZB-24-B0 Mechanical Drawing. Figure 3-2. Atmel ATZB-24-A2 Mechanical Drawing. ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 10 3.3 Pin Configuration Figure 3-3. Atmel ATZB-24-B0 Pinout. Figure 3-4. Atmel ATZB-24-A2 Pinout. ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 11 Table 3-7. Pin Descriptions. Connector pin Pin name Description 1 Reserved for stack operation (4) 2 3 4 5 6 7 SPI_CLK SPI_MISO SPI_MOSI GPIO0 GPIO1 GPIO2 OSC32K_OUT I/O Reserved for stack operation (4) Reserved for stack operation (4) O I/O I/O General purpose digital input/output 0 (2)(3)(4)(7) I/O tri-state General purpose digital input/output 1 (2)(3)(4)(7) I/O tri-state General purpose digital input/output 2 (2)(3)(4)(7) I/O tri-state 32.768kHz clock output (4)(5) (4) O 8 RESET Reset input (active low) 9, 22, 23 DGND Digital ground 10 CPU_CLK RF clock output. When module is in active state, 8MHz signal is present O on this line. While module is in the sleeping state, clock generation is also stopped (4). This pin is a test point and not to be used to clock External devices 11 I2C_CLK I2C Serial clock output (2)(3)(4)(7) 12 13 I2C_DATA UART_TXD Default state after power on 2 I C Serial data input/output (2)(3)(4)(7) UART receive input to ZigBit MCU (1)(2)(3)(4)(7) (1)(2)(3)(4)(7) O tri-state I/O tri-state I tri-state O tri-state 14 UART_RXD UART transmit output from ZigBit MCU 15 UART_RTS RTS input (Request to send) for UART hardware flow control. Active low I tri-state 16 UART_CTS CTS output (Clear to send) for UART hardware flow control. Active low O tri-state 17 GPIO6 General purpose digital input/output 6 (2)(3)(4)(7) I/O tri-state GPIO7 General purpose digital input/output 7 (2)(3)(4)(7) I/O tri-state General purpose digital input/output 3 (2)(3)(4)(7) I/O tri-state General purpose digital input/output 4 (2)(3)(4)(7) I/O tri-state General purpose digital input/output 5 (2)(3)(4)(7) I/O tri-state 18 19 20 21 GPIO3 GPIO4 GPIO5 (2)(3)(4)(7) (2)(3)(4)(7)(8) (9) 24, 25 D_VCC Digital supply voltage (VCC) 26 JTAG_TMS JTAG Test Mode Select (2)(3)(4)(6) 27 28 29 30 31 32 JTAG_TDI JTAG_TDO JTAG_TCK ADC_INPUT_3 ADC_INPUT_2 ADC_INPUT_1 JTAG Test Data Input JTAG Test Data Output JTAG Test Clock I (2)(3)(4)(6) I (2)(3)(4)(6) O (2)(3)(4)(6) I ADC Input Channel 3 (2)(3)(7) I tri-state ADC Input Channel 2 (2)(3)(7) I tri-state ADC Input Channel 1 (2)(3)(7) I tri-state I tri-state I/O tri-state 33 BAT ADC Input Channel 0, used for battery level measurement 34 A_VREF Input/Output reference voltage for ADC 35 AGND Analog ground 36 GPIO_1WR 1-wire interface (2)(3)(4)(7) 37 UART_DTR (2)(3)(7) I/O DTR input (Data Terminal Ready) for UART. Active low (2)(3)(4)(7) I tri-state ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 12 38 USART0_RXD 39 USART0_TXD USART/SPI Receive pin (2)(3)(4)(7) USART /SPI Transmit pin (2)(3)(4)(7) 40 USART0_EXTCLK USART/SPI External Clock 41 GPIO8 42 IRQ_7 43 IRQ_6 (2)(3)(4)(7)(11) General Purpose Digital Input/Output I tri-state O tri-state I/O tri-state I/O tri-state Digital Input Interrupt request 7 (2)(3)(4)(7) I tri-state Digital Input Interrupt request 6 (2)(3)(4)(7) I tri-state (2)(3)(4)(7) 44, 46, 48 RF GND RF Analog Ground 45 RFP_IO Differential RF Input/Output (10) I/O RFN_IO (10) I/O 47 Notes: Differential RF Input/Output 1. The UART_TXD pin is intended for input (that is, its designation as "TXD" implies some complex system containing ZigBit as its RF terminal unit), while the UART_RXD pin, vice versa, is for output. 2. Most of pins can be configured for general purpose I/O or for some alternate functions as described in details in the Atmel ATmega1281V Datasheet [1]. 3. GPIO pins can be programmed either for output, or for input with/without pull-up resistors. Output pin drivers are strong enough to drive LED displays directly (refer to figures on pages 387-388, [1]). 4. All digital pins are provided with protection diodes to D_VCC and DGND. 5. It is strongly recommended to avoid assigning an alternate function for OSC32K_OUT pin because it is used by BitCloud. However, this signal can be used if another peripheral or host processor requires 32.768kHz clock, otherwise this pin can be disconnected. 6. Normally, JTAG_TMS, JTAG_TDI, JTAG_TDO, JTAG_TCK pins are used for on-chip debugging and flash burning. They can be used for A/D conversion if JTAGEN fuse is disabled. 7. The following pins can be configured with the BitCloud software to be general-purpose I/O lines: GPIO0, GPIO1, GPIO2, GPIO3, GPIO4, GPIO5, GPIO6, GPIO7, GPIO8, GPIO_1WR, I2C_CLK, I2C_DATA, UART_TXD, UART_RXD, UART_RTS, UART_CTS, ADC_INPUT_3, ADC_INPUT_2, ADC_INPUT_1, BAT, UART_DTR, USART0_RXD, USART0_TXD, USART0_EXTCLK, IRQ_7, IRQ_6. Additionally, four JTAG lines can be programmed with software as GPIO as well, but this requires changing the fuse bits and will disable JTAG debugging. 8. With BitCloud, CTS pin can be configured to indicate sleep/active condition of the module thus providing a mechanism for power management of the host processor. If this function is necessary, a connection of this pin to an external pull-down resistor is recommended to prevent the undesirable transients during the module reset process. 9. Using ferrite bead and 1µF capacitor located closely to the power supply pin is recommended, as shown below: ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 13 10. Pins 44 through 48 are not designed for the Atmel ATZB-24-A2 module. Note these pins are used in Atmel ATZB- 24-B0, see them in antenna schematics below: Note: TXD, RXD of UART are crossed inside ZigBit Module. So external UART devices connecting to ZigBit Module should just follow straight connection for UART. UART_TXD_external_device <-> UART_TXD UART_RXD_external_device <-> UART_RXD 11. In SPI mode, USART0_EXTCLK is output. In USART mode, this pin can be configured as either input or output pin. 3.4 Mounting Information Figure 3-5 and Figure 3-6 show the PCB layout recommended for a ZigBit module. Neither via-holes nor wires are allowed on the PCB upper layer in the area occupied by the module. As a critical requirement, RF_GND pins should be grounded via several via-holes to be located right next to the pins thus minimizing inductance and preventing both mismatch and losses. ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 14 Figure 3-5. Atmel ATZB-24-B0 PCB Recommended Layout, top view. Figure 3-6. Atmel ATZB-24-A2 PCB Recommended Layout, top view. 3.5 Sample Antenna Reference Designs This section presents PCB designs which combine ZigBit with different antennas: PCB onboard antenna, external antenna and dual chip antenna. These antenna reference designs are recommended for successful design-in. ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 15 Figure 3-7. PCB layout: Symmetry Dipole Antenna Recommended for Atmel ATZB-24-B0. The symmetric dipole antenna above has been tuned for the particular design. The 'cut-and-paste' approach would not guarantee optimal performance because of multiple factors affecting proper antenna match, hence, affecting the pattern. The particular factors are the board material and thickness, shields, the material used for enclosure, the board neighborhood, and other components adjacent to antenna. ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 16 3.5.2 General Recommendations • • • Metal enclosure should not be used. Using low profile enclosure might also affect antenna tuning • ZigBit module should not be placed next to consumer electronics which might interfere with ZigBit RF frequency band Placing high profile components next to antenna should be avoided Having holes/vias punched around the periphery of the board eliminates parasitic radiation from the board edges also distorting antenna pattern ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 17 3.6 Soldering Profile Figure 3-8. Profile Data. ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 18 3.7 Internal Schematics ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 19 3.8 Handling instructions The ZigBit Modules are fixed with an EMI Shield to ensure compliance to Emission and Immunity rules. This shield is galvanic and NOT air tight. So cleaning of the module with IPA / other similar agents is not advised. Humidity protection coating (conformal) will cause deviated RF behavior and coating material being trapped inside EMI Shield. So this should be avoided. For products requiring conformal coating, it is advised to suitably mask the ZigBit before applying the coating to rest of the ZigBit carrier board. To protect ZigBit from humidity, the housing of the product should ensure compliance of suitable Ingress Protection standards. ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 20 4. Agency Certifications 4.1 United States (FCC) This equipment complies with Part 15 of the FCC rules and regulations. To fulfill FCC Certification requirements, an OEM manufacturer must comply with the following regulations: 1. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Example of label required for OEM product containing ATZB-24-A2 module Contains FCC ID: VW4A090664 The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (i.) this device may not cause harmful interference and (ii.) this device must accept any interference received, including interference that may cause undesired operation. Example of label required for OEM product containing ATZB-24-B0 module Contains FCC ID: VW4A090665 The enclosed device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (i.) this device may not cause harmful interference and (ii.) this device must accept any interference received, including interference that may cause undesired operation. Any similar wording that expresses the same meaning may be used. ATZB-24-A2 module is Modular approved and does not need separate approval for this module when used on an application board ATZB-24-B0 is limited modular approved and required separate approval for this module when used on an application board 4.2 Canada (IC) ATZB-24-A2 Module complies with Industry Canada specifications RSS-210 and RSS – Gen IC ID for ATZB-24-A2 is 11019A-090664 ATZB-24-A2 module is Modular approved and does not need separate approval for this module when used on an application board 4.3 European Union (ETSI) The ATZB-24-A2 and ATZB-24-B0 Modules has been certified for use in European Union countries. If the ATZB-24-A2 and ATZB-24-B0 Modules are incorporated into a product, the manufacturer must ensure compliance of the final product to the European harmonized EMC and low-voltage/safety standards. A Declaration of Conformity must be issued for each of these standards and kept on file as described in Annex II of the R&TTE Directive. ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 21 Furthermore, the manufacturer must maintain a copy of the ATZB-24-A2 and ATZB-24-B0 Modules documentation and ensure the final product does not exceed the specified power ratings, antenna specifications, and/or installation requirements as specified in the user manual. If any of these specifications are exceeded in the final product, a submission must be made to a notified body for compliance testing to all required standards. IMPORTANT: The 'CE' marking must be affixed to a visible location on the OEM product. The CE mark shall consist of the initials "CE" taking the following form: If the CE marking is reduced or enlarged, the proportions given in the above graduated drawing must be respected. The CE marking must have a height of at least 5mm except where this is not possible on account of the nature of the apparatus. The CE marking must be affixed visibly, legibly, and indelibly. More detailed information about CE marking requirements you can find at "DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL" on 9 March 1999 at section 12. 4.4 Using Limited Modular Certified Products The ATZB-24-B0 ZigBit Module is certified under part 15 of FCC rules. The Modular certification category of this module is “Limited Modular”. The End product using these modules hence has to undergo compliance testing and receive a new FCC ID for the final product carrying these modules. Certification of the final product lies solely with the type of design of the final product, excluding the ZigBit. 1. Warning: To be used with the ATZB-24-B0 module, the external antennas have been tested and approved which are specified in here below. The ATZB-24-B0 Module may be integrated with other custom design antennas which OEM installer must authorize following the FCC 15.21 requirements. The Original Equipment Manufacturer (OEM) must ensure that the OEM modular transmitter must be labeled with its own FCC ID number. This includes a clearly visible label on the outside of the final product enclosure that displays the contents shown below. If the FCC ID is not visible when the equipment is installed inside another device, then the outside of the device into which the equipment is installed must also display a label referring to the enclosed equipment. IMPORTANT: This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation (FCC 15.19). The internal / external antenna(s) used for this mobile transmitter must provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This device is approved as a mobile device with respect to RF expo- sure compliance, and may only be marketed to OEM installers. Use in portable exposure conditions (FCC 2.1093) requires separate equipment authorization. IMPORTANT: Modifications not expressly approved by this company could void the user's authority to operate this equipment (FCC section 15.21). ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 22 IMPORTANT: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense (FCC section 15.105). 4.5 Approved Antenna List The Atmel ATZB-24-A2 Module works with integrated dual chip antenna. The design of the antenna is fully compliant with all the aforementioned regulation. The Atmel ATZB-24-B0 Module has been tested and approved for use with the antennas listed in Table 4-1. ATZB-24B0 Module may be integrated with other custom design antennas which OEM installer must authorize with respective regulatory agencies. For further information see Section 4.4. Table 4-1. 5. Approved Antenna Specifications Part number Manufacture and description Gain [dBi] Minimum separation [cm] 2010B48-01 Antenova Titanis, swivel antenna (1/4 wave antenna) with SMA connector, frequency range 2.4 - 2.5GHz 2.2 20 17010.10 WiMo, swivel antenna (1/2 wave antenna) with SMA connector, frequency range 2.35 - 2.5GHz 2.1 20 Ordering Information Table 5-1. Ordering Information Part number Description ATZB-24-B0R 2.4GHz IEEE802.15.4/ZigBee OEM module with balanced RF port, tape and reel ATZB-24-B0 2.4GHz IEEE802.15.4/ZigBee OEM module with balanced RF port, single unit ATZB-24-A2R 2.4GHz IEEE802.15.4/ZigBee OEM module with dual chip antenna, tape and reel ATZB-24-A2 2.4GHz IEEE802.15.4/ZigBee OEM module with dual chip antenna, single unit Note: Tape and reel quantity: 200. ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 23 6. Revision History Doc. Rev. Date Comments 8226C 07/2013 New template and several other changes 8226B 06/2009 8226A 10/2008 Initial document release ATZB-24-A2/B0 [ZigBit 2.4GHz Wireless Modules] 8226C−AVR−07/2013 24 Atmel Corporation Atmel Asia Limited Atmel Munich GmbH Atmel Japan G.K. 1600 Technology Drive Unit 01-5 & 16, 19F Business Campus 16F Shin-Osaki Kangyo Building San Jose, CA 95110 BEA Tower, Millennium City 5 Parkring 4 1-6-4 Osaki, Shinagawa-ku USA 418 Kwun Tong Road D-85748 Garching b. Munich Tokyo 141-0032 Tel: (+1)(408) 441-0311 Kwun Tong, Kowloon GERMANY JAPAN Fax: (+1)(408) 487-2600 HONG KONG Tel: (+49) 89-31970-0 Tel: (+81)(3) 6417-0300 www.atmel.com Tel: (+852) 2245-6100 Fax: (+49) 89-3194621 Fax: (+81)(3) 6417-0370 Fax: (+852) 2722-1369 © 2013 Atmel Corporation. All rights reserved. / Rev.: 8226C−AVR−07/2013 Atmel®, Atmel logo and combinations thereof, AVR®, BitCloud®, Enabling Unlimited Possibilities®, ZigBit®, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.