NCP153 D

NCP153
Dual 130 mA, Low IQ, Low
Dropout Voltage Regulator
The NCP153 is 130 mA, Dual Output Linear Voltage Regulator that
provides a very stable and accurate voltage with very low noise and
high Power Supply Rejection Ratio (PSRR) suitable for RF
applications. In order to optimize performance for battery operated
portable applications, the NCP153 employs the Adaptive Ground
Current Feature for low ground current consumption during light−load
conditions. Device also incorporates foldback current protection to
reduce short circuit current and protect powered devices.
MARKING
DIAGRAM
GA M
Features
XDFN6, 1.2x1.2
CASE 711AT
• Operating Input Voltage Range: 1.9 V to 5.25 V
• Two Independent Output Voltages:
GA = Specific Device Code
M = Date Code
(for details please refer to the Ordering Information section)
Very Low Dropout: 130 mV Typical at 130 mA
Low IQ of typ. 50 mA per Channel
High PSRR: 75 dB at 1 kHz
Two Independent Enable Pins
Over Current Protection: 165 mA Typical
Foldback Short Circuit Protection
Thermal Shutdown
Stable with a 0.22 mF Ceramic Output Capacitor
Available in XDFN6 1.2 x 1.2 mm Package
Active Output Discharge for Fast Output Turn−Off
These are Pb−Free Devices
PIN CONNECTIONS
OUT1
1
OUT2
2
GND
3
GND
•
•
•
•
•
•
•
•
•
•
•
www.onsemi.com
6
EN1
5
IN
4
EN2
XDFN6
(Top view)
Typical Applications
• Smartphones, Tablets, Wireless Handsets
• Wireless LAN, Bluetooth®, ZigBee® Interfaces
• Other Battery Powered Applications
ORDERING INFORMATION
See detailed ordering and shipping information on page 13 of
this data sheet.
NCP153
VIN1
VOUT2
IN
EN1
OUT2
EN2
OUT1
VOUT1
GND
CIN1
0.22 mF
COUT1
0.22 mF
COUT2
0.22 mF
Figure 1. Typical Application Schematic
© Semiconductor Components Industries, LLC, 2015
October, 2015 − Rev. 1
1
Publication Order Number:
NCP153/D
NCP153
ENABLE
LOGIC
EN1
THERMAL
SHUTDOWN
MOSFET
DRIVER WITH
CURRENT LIMIT
OUT1
ACTIVE
DISCHARGE
EN1
GND
EN2
ACTIVE
DISCHARGE
BANDGAP
REFERENCE
IN
OUT2
MOSFET
DRIVER WITH
CURRENT LIMIT
THERMAL
SHUTDOWN
ENABLE
LOGIC
EN2
Figure 2. Simplified Schematic Block Diagram
PIN FUNCTION DESCRIPTION
Pin No.
XDFN6
Pin
Name
1
OUT1
Regulated output voltage of the first channel. A small 0.22 mF ceramic capacitor is needed from this pin to
ground to assure stability.
2
OUT2
Regulated output voltage of the second channel. A small 0.22 mF ceramic capacitor is needed from this pin
to ground to assure stability.
3
GND
Power supply ground. Soldered to the copper plane allows for effective heat dissipation.
4
EN2
Driving EN2 over 0.9 V turns−on OUT2. Driving EN below 0.4 V turns−off the OUT2 and activates the active
discharge.
5
IN
6
EN1
−
EP
Description
Input pin common for both channels. It is recommended to connect 0.22 mF ceramic capacitor close to the
device pin.
Driving EN1 over 0.9 V turns−on OUT1. Driving EN below 0.4 V turns−off the OUT1 and activates the active
discharge.
Exposed pad must be tied to ground. Soldered to the copper plane allows for effective thermal dissipation.
www.onsemi.com
2
NCP153
ABSOLUTE MAXIMUM RATINGS
Rating
Symbol
Value
Unit
VIN
−0.3 V to 6 V
V
Output Voltage
VOUT1,
VOUT2
−0.3 V to VIN + 0.3 V or 6 V
V
Enable Inputs
VEN1,
VEN2
−0.3 V to VIN + 0.3 V or 6 V
V
tSC
Indefinite
s
TJ(MAX)
150
°C
Input Voltage (Note 1)
Output Short Circuit Duration
Maximum Junction Temperature
TSTG
−55 to 150
°C
ESD Capability, Human Body Model (Note 2)
ESDHBM
2000
V
ESD Capability, Machine Model (Note 2)
ESDMM
200
V
Storage Temperature
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Refer to ELECTRICAL CHARACTERISTIS and APPLICATION INFORMATION for Safe Operating Area.
2. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per EIA/JESD22−A114
ESD Machine Model tested per EIA/JESD22−A115
Latchup Current Maximum Rating tested per JEDEC standard: JESD78.
THERMAL CHARACTERISTICS (Note 3)
Rating
Symbol
Thermal Characteristics, XDFN6 1.2 x 1.2 mm,
Thermal Resistance, Junction−to−Air
Thermal Characterization Parameter, Junction−to−Lead (Pin 2)
3. Single component mounted on 1 oz, FR4 PCB with 645mm2 Cu area.
www.onsemi.com
3
qJA
qJL
Value
Unit
°C/W
170
NCP153
ELECTRICAL CHARACTERISTIC
−40°C ≤ TJ ≤ 85°C; VIN = VOUT(NOM) + 1 V or 2.5 V, whichever is greater; VEN = 0.9 V, IOUT = 1 mA, CIN = COUT = 0.22 mF. Typical
values are at TJ = +25°C. Min/Max values are specified for TJ = −40°C and TJ = 85°C respectively. (Note 4)
Test Conditions
Parameter
Operating Input Voltage
Output Voltage Accuracy
VOUT > 2 V
−40°C ≤ TJ ≤ 85°C
Symbol
Min
Max
Unit
VIN
1.9
5.25
V
VOUT
−2
+2
%
−60
+60
mV
VOUT ≤ 2 V
Typ
Line Regulation
VOUT + 0.5 V or 2.5 V ≤ VIN ≤ 5 V
RegLINE
0.02
0.1
%/V
Load Regulation
IOUT = 1 mA to 130 mA, TJ = +25°C
RegLOAD
15
50
mV
265
280
130
150
Dropout Voltage (Note 5)
VOUT(nom) = 1.8 V
IOUT = 130 mA, TJ = +25°C
VOUT(nom) = 3.3 V
VDO
mV
Output Current
TJ = +25°C
IOUT
130
OCP Level
VOUT = 90% VOUT(nom), TJ = +25°C
IOCP
135
Short Circuit Current
VOUT = 0 V, TJ = +25°C
ISC
55
Quiescent Current
IOUT = 0 mA, EN1 = VIN, EN2 = 0 V or EN2 = VIN,
EN1 = 0 V
IQ
50
100
mA
IOUT1 = IOUT2 = 0 mA, VEN1 = VEN2 = VIN
IQ
85
200
mA
IDIS
0.1
1
mA
Shutdown Current (Note 6)
VEN ≤ 0.4 V, VIN = 5.25 V
EN Pin Threshold Voltage
High Threshold
Low Threshold
VEN Voltage increasing
VEN Voltage decreasing
EN Pin Input Current
VEN = VIN = 5.25 V
Power Supply Rejection Ratio
VIN = VOUT+1 V for VOUT > 2 V, VIN =
2.5 V, for VOUT ≤ 2 V, IOUT = 10 mA
Output Noise Voltage
f = 10 Hz to 100 kHz
Active Discharge Resistance
mA
165
195
mA
mA
V
VEN_HI
VEN_LO
0.9
0.4
0.3
PSRR
75
dB
VN
75
mVrms
VIN = 4 V, VEN < 0.4 V
RDIS
50
W
Thermal Shutdown Temperature
Temperature increasing from TJ = +25°C
TSD
160
°C
Thermal Shutdown Hysteresis
Temperature falling from TSD
TSDH
f = 1 kHz
−
20
1.0
mA
IEN
−
°C
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
4. Performance guaranteed over the indicated operating temperature range by design and/or characterization. Production tested at TJ = TA
= 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
5. Characterized when VOUT falls 100 mV below the regulated voltage at VIN = VOUT(NOM) + 1 V.
6. Shutdown Current is the current flowing into the IN pin when the device is in the disable state.
www.onsemi.com
4
NCP153
1.85
3.35
1.84
3.34
VOUT, OUTPUT VOLTAGE (V)
VOUT, OUTPUT VOLTAGE (V)
TYPICAL CHARACTERISTICS
1.83
1.82
1.81
IOUT = 1 mA
1.80
IOUT = 130 mA
1.79
1.78
VIN = 2.8 V
VOUT = 1.8 V
CIN = 0.22 mF
COUT = 0.22 mF
1.77
1.76
1.75
−40 −25 −10
5
35
20
50
65
IOUT = 130 mA
3.29
3.28
VIN = 4.3 V
VOUT = 3.3 V
CIN = 0.22 mF
COUT = 0.22 mF
3.27
5
20
50
35
65
80
TJ, JUNCTION TEMPERATURE (°C)
Figure 3. Output Voltage vs. Temperature –
VOUT = 1.8 V
Figure 4. Output Voltage vs. Temperature –
VOUT = 3.3 V
95
750
VIN = 4.3 V
VOUT = 3.3 V
VEN1 = VEN2 = VIN
CIN = 0.22 mF
COUT = 0.22 mF
400
350
300
TJ = 85°C
IGND, GROUND CURRENT (mA)
IGND, GROUND CURRENT (mA)
3.30
TJ, JUNCTION TEMPERATURE (°C)
450
TJ = 25°C
250
200
TJ = −40°C
150
100
50
0
0.001 0.01
0.1
1
10
100
VEN1 = VEN2 = VIN,
OUT1−LOAD
OUT2−LOAD
VIN = 4.3 V
VOUT = 3.3 V
CIN = 0.22 mF
COUT = 0.22 mF
675
600
525
450
VEN1 = VEN2 = VIN,
OUT1−LOAD
375
300
225
VEN1 = 0 V, VEN2 = VIN,
OUT1−LOAD
150
75
0
1000
0
13
26
52
39
65
78
91
104 117 130
IOUT, OUTPUT CURRENT (mA)
IOUT, OUTPUT CURRENT (mA)
Figure 5. Ground Current vs. Output Current –
One Output Load
Figure 6. Ground Current vs. Output Current –
Different Load Combinations
0.05
90
REGLINE, LINE REGULATION (%/V)
100
IQ, QUIESCENT CURRENT (mA)
IOUT = 1 mA
3.31
3.26
3.25
−40 −25 −10
95
80
3.33
3.32
85°C
80
−40°C
70
25°C
60
50
0.04
0.03
0.02
0.01
0
−0.01
40
VIN = 4.3 V
VOUT = 3.3 V
CIN = 0.22 mF
COUT = 0.22 mF
30
20
10
0
0
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5
VIN = 2.5 V to 5.25 V
VOUT = 1.8 V
IOUT = 1 mA
CIN = 0.22 mF
COUT = 0.22 mF
−0.02
−0.03
−0.04
−0.05
−40 −25
5.0 5.5
−10
5
20
35
50
65
80
VIN, INPUT VOLTAGE (V)
TJ, JUNCTION TEMPERATURE (°C)
Figure 7. Quiescent Current vs. Input Voltage
– Both Outputs ON
Figure 8. Line Regulation vs. Temperature −
VOUT = 1.8 V
www.onsemi.com
5
95
NCP153
TYPICAL CHARACTERISTICS
0.03
0.02
0.01
0
−0.01
VIN = 4.3 V to 5.25 V
VOUT = 3.3 V
IOUT = 1 mA
CIN = 0.22 mF
COUT = 0.22 mF
−0.02
−0.03
−0.04
−0.05
−40 −25
REGLOAD, LOAD REGULATION (mV)
REGLOAD, LOAD REGULATION (mV)
0.04
−10
20
5
35
50
65
80
95
VIN = 2.5 V
VOUT = 3.3 V
IOUT = 1 mA to 130 mA
CIN = 0.22 mF
COUT = 0.22 mF
9
8
7
6
5
4
3
2
1
0
−40
−25
−10
5
35
20
50
65
80
95
TJ, JUNCTION TEMPERATURE (°C)
Figure 9. Line Regulation vs. Temperature −
VOUT = 3.3 V
Figure 10. Load Regulation vs. Temperature −
VOUT = 1.8 V
300
10
9
8
7
6
5
4
VIN = 4.3 V
VOUT = 3.3 V
IOUT = 1 mA to 130 mA
CIN = 0.22 mF
COUT = 0.22 mF
3
2
1
0
−40 −25
−10
5
35
20
50
65
80
VIN = 2.8 V
VOUT = 1.8 V
CIN = 0.22 mF
COUT = 0.22 mF
270
240
210
TJ = 85°C
TJ = 25°C
180
150
TJ = −40°C
120
90
60
30
0
0
95
13
26
39
52
78
65
91
104 117 130
TJ, JUNCTION TEMPERATURE (°C)
IOUT, OUTPUT CURRENT (mA)
Figure 11. Load Regulation vs. Temperature −
VOUT = 3.3 V
Figure 12. Dropout Voltage vs. Output Current
– VOUT = 1.8 V
350
VIN = 4.3 V
VOUT = 3.3 V
CIN = 0.22 mF
COUT = 0.22 mF
180
160
140
VDROP, DROPOUT VOLTAGE (mV)
200
VDROP, DROPOUT VOLTAGE (mV)
10
TJ, JUNCTION TEMPERATURE (°C)
VDROP, DROPOUT VOLTAGE (mV)
REGLINE, LINE REGULATION (%/V)
0.05
TJ = 85°C
TJ = 25°C
120
100
80
TJ = −40°C
60
40
20
0
0
13
26
39
52
65
78
91
104 117 130
315
280
245
VIN = 2.8 V
VOUT = 1.8 V
CIN = 0.22 mF
COUT = 0.22 mF
IOUT = 130 mA
210
IOUT = 75 mA
175
140
105
70
35
0
−40 −25
IOUT = 0 mA
−10
5
20
35
50
65
80
95
IOUT, OUTPUT CURRENT (mA)
TJ, JUNCTION TEMPERATURE (°C)
Figure 13. Dropout Voltage vs. Output Current
– VOUT = 3.3 V
Figure 14. Dropout Voltage vs. Temperature –
VOUT = 1.8 V
www.onsemi.com
6
NCP153
TYPICAL CHARACTERISTICS
300
VIN = 4.3 V
VOUT = 3.3 V
CIN = 0.22 mF
COUT = 0.22 mF
140
ICL, CURRENT LIMIT (mA)
160
270
IOUT = 130 mA
120
100
IOUT = 75 mA
80
60
IOUT = 0 mA
40
20
0
−40 −25
5
−10
20
35
50
65
95
80
210
180
150
120
VIN = 4.3 V
VOUT = 3.3 V
CIN = 0.22 mF
COUT = 0.22 mF
90
60
−10
5
20
35
50
65
80
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 15. Dropout Voltage vs. Temperature –
VOUT = 3.3 V
Figure 16. Current Limit vs. Temperature
100
4.0
90
3.6
80
70
60
50
40
30
VIN = 4.3 V
VOUT = 0 V
CIN = 0.22 mF
COUT = 0.22 mF
20
10
0
−40 −25 −10
5
20
35
50
65
80
95
3.2
TJ = −40°C
2.8
2.4
TJ = 25°C
2.0
TJ = 85°C
1.6
1.2
VIN = 4.3 V
VOUT = 3.3 V
CIN = 0.22 mF
COUT = 0.22 mF
0.8
0.4
0
0
95
20
40
60
80
100 120 140 160 180 200
TJ, JUNCTION TEMPERATURE (°C)
IOUT, OUTPUT CURRENT (mA)
Figure 17. Short Circuit Current vs.
Temperature
Figure 18. Current Foldback Protection − 3.3 V
2.0
200
1.8
IDIS, DISABLE CURRENT (nA)
VOUT, OUTPUT VOLTAGE (V)
240
30
0
−40 −25
VOUT, OUTPUT VOLTAGE (V)
ISC, SHORT CIRCUIT CURRENT (mA)
VDROP, DROPOUT VOLTAGE (mV)
200
180
TJ = −40°C
1.6
1.4
TJ = 25°C
1.2
TJ = 85°C
1.0
0.8
0.6
VIN = 2.8 V
VOUT = 1.8 V
CIN = 0.22 mF
COUT = 0.22 mF
0.4
0.2
0
0
20
40
60
80
100 120 140 160 180 200
180
160
140
120
100
80
60
40
VIN = 5.5 V
VOUT = 3.3 V
CIN = 0.22 mF
COUT = 0.22 mF
20
0
−40 −25 −10
5
20
35
50
65
80
IOUT, OUTPUT CURRENT (mA)
TJ, JUNCTION TEMPERATURE (°C)
Figure 19. Current Foldback Protection − 1.8 V
Figure 20. Disable Current vs. Temperature
www.onsemi.com
7
95
NCP153
TYPICAL CHARACTERISTICS
100
1.0
Unstable Operation
0.8
OFF −> ON
0.7
0.6
ESR (W)
ON −> OFF
0.5
0.4
0.2
0.01
−10
5
20
35
50
65
80
0
95
13
39
26
52
65
78
91
104 117 130
TJ, JUNCTION TEMPERATURE (°C)
IOUT, OUTPUT CURRENT (mA)
Figure 21. Enable Voltage Threshold vs.
Temperature
Figure 22. Stability vs. ESR
450
400
350
300
250
200
VIN = 4.3 V
VOUT = 3.3 V
CIN = 0.22 mF
COUT = 0.22 mF
150
100
−25 −10
5
20
35
50
65
80
95
50
45
40
35
30
25
20
VIN = 4.3 V
VOUT = 3.3 V
CIN = 0.22 mF
COUT = 0.22 mF
15
10
5
0
−40 −25
−10
5
20
50
35
65
80
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 23. Current To Enable Pin vs.
Temperature
Figure 24. Discharge Resistance vs.
Temperature
95
100
100
90
RR, RIPPLE REJECTION (dB)
RR, RIPPLE REJECTION (dB)
VOUT = 1.8 V
1
0.1
500
50
0
−40
VOUT = 3.3 V
Stable Operation
VIN = 4.3 V
VOUT = 3.3 V
CIN = 0.22 mF
COUT = 0.22 mF
0.3
0.1
0
−40 −25
IEN, CURRENT TO ENABLE PIN (nA)
10
RDIS, DISCHARGE RESISTANCE (W)
VEN, ENABLE VOLTAGE (V)
0.9
80
1 mA
70
10 mA
60
50
40
VIN = 2.8 V
VOUT = 1.8 V
CIN = none
COUT = 0.22 mF
30
20
10
0
100
1K
100 mA
10K
100K
1M
90
80
1 mA
70
10 mA
60
50
40
VIN = 4.3 V
VOUT = 3.3 V
CIN = none
COUT = 0.22 mF
30
20
10
0
10M
100
1K
100 mA
10K
100K
1M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 25. Power Supply Rejection Ratio,
VOUT = 1.8 V, COUT = 0.22 mF
Figure 26. Power Supply Rejection Ratio,
VOUT = 3.3 V, COUT=0.22 mF
www.onsemi.com
8
10M
NCP153
TYPICAL CHARACTERISTICS
OUTPUT VOLTAGE NOISE (nV/√Hz)
10K
1K
10 mA
RMS Output Noise (mV)
100 mA
100
VIN = 2.8 V
VOUT = 1.8 V
CIN = 0.22 mF
COUT = 0.22 mF
MLCC, X7R,
1206 size
10
1 mA
IOUT
10 Hz − 100 kHz
100 Hz − 100 kHz
1 mA
68.07
67.07
10 mA
67.30
66.31
100 mA
68.31
67.35
IOUT
10 Hz − 100 kHz
100 Hz − 100 kHz
1
10
100
1K
10K
100K
1M
FREQUENCY (Hz)
Figure 27. Output Voltage Noise Spectral
Density for VOUT = 1.8 V, COUT = 220 nF
OUTPUT VOLTAGE NOISE (nV/√Hz)
10K
10 mA
1K
RMS Output Noise (mV)
100 mA
1 mA
108.34
106.75
10 mA
107.18
105.56
100 mA
109.12
107.54
100
VIN = 4.3 V
VOUT = 3.3 V
CIN = 0.22 mF
COUT = 0.22 mF
MLCC, X7R,
1206 size
10
1 mA
1
10
100
1K
10K
100K
1M
FREQUENCY (Hz)
Figure 28. Output Voltage Noise Spectral
Density for VOUT = 3.3 V, COUT = 220 nF
www.onsemi.com
9
NCP153
VOUT1
VOUT2
VOUT2 = 1.8 V
IOUT1 = 10 mA
VOUT1
IOUT2 = 1 mA
COUT1 = COUT2 = 1 mF
VOUT2
40 ms/div
40 ms/div
Figure 29. Enable Turn−on Response –
VR1 = 10 mA, VR2 = Off
Figure 30. Enable Turn−on Response –
VR1 = 10 mA, VR2 = 1 mA
tRISE = 1 ms
tFALL = 1 ms
VOUT2
20 mV/div
COUT1 = 220 nF
COUT2 = 220 nF
20 mV/div
VIN = 3.8 V to 4.8 V
IOUT2 = 10 mA
VOUT1
VIN
500 mV/div
VIN
VOUT2
20 mV/div
1 V/div 1 V/div
VIN = 3.8 V
VOUT1 = 3.3 V
VOUT2 = disable
IOUT1 = 10 mA
COUT1 = COUT2 = 1 mF
IIN
20 mV/div
500 mV/div
1 V/div 1 V/div
IIN
VIN = 4.3 V
VOUT1 = 3.3 V
VEN
VIN = 4.8 V to 3.8 V
IOUT2 = 10 mA
VOUT1
COUT1 = 220 nF
COUT2 = 220 nF
2 ms/div
2 ms/div
Figure 31. Line Transient Response – Rising
Edge, VEN1 = VIN, VEN1 = 0 V, VOUT1 = 3.3 V,
IOUT1 = 10 mA
Figure 32. Line Transient Response – Falling
Edge, VEN1 = VIN, VEN1 = 0 V, VOUT1 = 3.3 V,
IOUT1 = 10 mA
50 mA/div
tRISE = 1 ms
VOUT1
VIN = 4.3 V
VOUT1 = 3.3 V
VOUT2
VOUT2 = 1.8 V
IOUT2 = 0 mA
20 mV/div 50 mV/div
20 mV/div 50 mV/div
50 mA/div
IOUT1
IOUT1
COUT1 = 220 nF
COUT2 = 220 nF
tFALL = 1 ms
VOUT1
VIN = 4.3 V
VOUT1 = 3.3 V
VOUT2
VOUT2 = 1.8 V
IOUT2 = 0 mA
COUT1 = 220 nF
COUT2 = 220 nF
4 ms/div
4 ms/div
Figure 33. Load Transient Response – Rising
Edge, IOUT = 1 mA to 130 mA – 3.3 V
Figure 34. Load Transient Response– Falling
Edge, IOUT = 130 mA to 1 mA – 3.3 V
www.onsemi.com
10
50 mA/div
500 mV/div
VEN
50 mA/div
500 mV/div
TYPICAL CHARACTERISTICS
NCP153
20 mV/div 50 mA/div
tRISE = 1 ms
VOUT1
VIN = 4.3 V
VOUT1 = 3.3 V
VOUT2
VOUT2 = 1.8 V
IOUT1 = 0 mA
50 mV/div
IOUT2
COUT1 = 220 nF
COUT2 = 220 nF
tFALL = 1 ms
VIN = 4.3 V
VOUT1 = 3.3 V
VOUT2 = 1.8 V
IOUT1 = 0 mA
VOUT1
COUT1 = 220 nF
COUT2 = 220 nF
VOUT2
4 ms/div
Figure 36. Load Transient Response – Falling
Edge, IOUT = 130 mA to 1 mA – 1.8 V
IOUT2
20 mV/div 50 mA/div
4 ms/div
tRISE = 1 ms
VIN = 4.3 V
VOUT1 = 3.3 V
VOUT2 = 1.8 V
IOUT1 = 0 mA
VOUT1
50 mV/div
VOUT2
COUT1 = 220 nF
COUT2 = 220 nF
IOUT2
tFALL = 1 ms
VIN = 4.3 V
VOUT1 = 3.3 V
VOUT2 = 1.8 V
IOUT1 = 0 mA
COUT1 = 220 nF
COUT2 = 220 nF
VOUT1
VOUT2
4 ms/div
4 ms/div
Figure 37. Load Transient Response – Rising
Edge, IOUT = 0.1 mA to 130 mA
Figure 38. Load Transient Response – Falling
Edge, IOUT = 130 mA to 0.1 mA
VIN
VIN = 4.3 V
VOUT1 = 3.3 V
VOUT2 = 1.8 V
VOUT1
VOUT2
VEN
VOUT1
1 V/div
500 mV/div
IOUT2
Figure 35. Load Transient Response – Rising
Edge, IOUT = 1 mA to 130 mA – 1.8 V
500 mV/div
50 mV/div 20 mV/div
50 mA/div
50 mV/div 20 mV/div
50 mA/div
TYPICAL CHARACTERISTICS
IOUT1 = 10 mA
IOUT2 = 10 mA
CIN = COUT1 =
COUT1 = 220 nF
tFALL = 1 ms
COUT = 4.7 mF
COUT = 1 mF
VIN = 4.3 V
VOUT1 = 3.3 V
VOUT2 = 1.8 V
20 ms/div
200 ms/div
Figure 39. Turn−on/off − Slow Rising VIN
Figure 40. Enable Turn−off
www.onsemi.com
11
NCP153
APPLICATIONS INFORMATION
General
disable state the device consumes as low as typ. 10 nA from
the VIN.
If the EN pin voltage >0.9 V the device is guaranteed to
be enabled. The NCP153 regulates the output voltage and
the active discharge transistor is turned−off.
The both EN pin has internal pull−down current source
with typ. value of 300 nA which assures that the device is
turned−off when the EN pin is not connected. In the case
where the EN function isn’t required the EN should be tied
directly to IN.
The NCP153 is a dual output high performance 130 mA
Low Dropout Linear Regulator. This device delivers very
high PSRR (75 dB at 1 kHz) and excellent dynamic
performance as load/line transients. In connection with low
quiescent current this device is very suitable for various
battery powered applications such as tablets, cellular
phones, wireless and many others. Each output is fully
protected in case of output overload, output short circuit
condition and overheating, assuring a very robust design.
The NCP153 device is housed in XDFN−6 1.2 mm x
1.2 mm package which is useful for space constrains
application.
Foldback Short Circuit Protection
The internal foldback limits short circuit current to typical
55 mA and protects powered device against overheating.
Maximum output current is internaly limited to 165 mA
(typ). The current limit and short circuit protection will work
properly over whole temperature range and also input
voltage range. There is no limitation for the short circuit
duration. Thess protections are independent for each
channel. Short circuit on the one channel do not influence
second channel which will work according to specification.
Input Capacitor Selection (CIN)
It is recommended to connect at least a 0.22 mF Ceramic
X5R or X7R capacitor as close as possible to the IN pin of
the device. This capacitor will provide a low impedance path
for unwanted AC signals or noise modulated onto constant
input voltage. There is no requirement for the min. or max.
ESR of the input capacitor but it is recommended to use
ceramic capacitors for their low ESR and ESL. A good input
capacitor will limit the influence of input trace inductance
and source resistance during sudden load current changes.
Larger input capacitor may be necessary if fast and large
load transients are encountered in the application.
Thermal Shutdown
When the die temperature exceeds the Thermal Shutdown
threshold (TSD − 160°C typical), Thermal Shutdown event
is detected and the affected channel is turn−off. Second
channel still working. The channel which is overheated will
remain in this state until the die temperature decreases below
the Thermal Shutdown Reset threshold (TSDU − 140°C
typical). Once the device temperature falls below the 140°C
the appropriate channel is enabled again. The thermal
shutdown feature provides the protection from a
catastrophic device failure due to accidental overheating.
This protection is not intended to be used as a substitute for
proper heat sinking. The long duration of the short circuit
condition to some output channel could cause turn−off other
output when heat sinking is not enough and temperature of
the other output reach TSD temperature.
Output Decoupling (COUT)
The NCP153 requires an output capacitor for each output
connected as close as possible to the output pin of the
regulator. The recommended capacitor value is 0.22 mF and
X7R or X5R dielectric due to its low capacitance variations
over the specified temperature range. The NCP153 is
designed to remain stable with minimum effective
capacitance of 0.15 mF to account for changes with
temperature, DC bias and package size. Especially for small
package size capacitors such as 0201 the effective
capacitance drops rapidly with the applied DC bias.
There is no requirement for the minimum value of
Equivalent Series Resistance (ESR) for the COUT but the
maximum value of ESR should be less than 2 W. Larger
output capacitors and lower ESR could improve the load
transient response or high frequency PSRR. It is not
recommended to use tantalum capacitors on the output due
to their large ESR. The equivalent series resistance of
tantalum capacitors is also strongly dependent on the
temperature, increasing at low temperature.
Power Dissipation
As power dissipated in the NCP153 increases, it might
become necessary to provide some thermal relief. The
maximum power dissipation supported by the device is
dependent upon board design and layout. Mounting pad
configuration on the PCB, the board material, and the
ambient temperature affect the rate of junction temperature
rise for the part.
The maximum power dissipation the NCP153 can handle
is given by:
Enable Operation
The NCP153 uses the dedicated EN pin for each output
channel. This feature allows driving outputs separately.
If the EN pin voltage is <0.4 V the device is guaranteed to
be disabled. The pass transistor is turned−off so that there is
virtually no current flow between the IN and OUT. The
active discharge transistor is active so that the output voltage
VOUT is pulled to GND through a 50 W resistor. In the
P D(MAX) +
ƪ125° C * T Aƫ
q JA
(eq. 1)
The power dissipated by the NCP153 for given
application conditions can be calculated from the following
equations:
www.onsemi.com
12
NCP153
I GND ) I OUT1ǒV IN * V OUT1Ǔ
(eq. 2)
) I OUT2ǒV IN * V OUT2Ǔ
1.25
qJA, JUNCTION−TO−AMBIENT
THERMAL RESISTANCE (°C/W)
240
220
PD(MAX), TA = 25°C, 2 oz Cu
200
1.00
180
PD(MAX), TA = 25°C, 1 oz Cu
160
qJA, 1 oz Cu
140
0.75
qJA, 2 oz Cu
120
0.50
100
80
60
0
100
200
300
400
500
600
PD(MAX), MAXIMUM POWER
DISSIPATION (W)
P D [ V IN
0.25
700
COPPER HEAT SPREADER AREA (mm2)
Figure 41. qJA vs. Copper Area (XDFN−6)
Reverse Current
nominal value. This time is dependent on various
application conditions such as VOUT(NOM), COUT, TA.
The PMOS pass transistor has an inherent body diode
which will be forward biased in the case that VOUT > VIN.
Due to this fact in cases, where the extended reverse current
condition can be anticipated the device may require
additional external protection.
PCB Layout Recommendations
To obtain good transient performance and good regulation
characteristics place input and output capacitors close to the
device pins and make the PCB traces wide. In order to
minimize the solution size, use 0402 capacitors. Larger
copper area connected to the pins will also improve the
device thermal resistance. The actual power dissipation can
be calculated from the equation above (Equation 2). Expose
pad should be tied the shortest path to the GND pin.
Power Supply Rejection Ratio
The NCP153 features very good Power Supply Rejection
ratio. If desired the PSRR at higher frequencies in the range
100 kHz − 10 MHz can be tuned by the selection of COUT
capacitor and proper PCB layout.
Turn−On Time
The turn−on time is defined as the time period from EN
assertion to the point in which VOUT will reach 98% of its
ORDERING INFORMATION
Device
NCP153MX330180TCG
Voltage Option*
(OUT1/OUT2)
Marking
Marking
Rotation
3.3 V/1.8 V
GA
0°
Package
Shipping†
XDFN-6
(Pb-Free)
3000 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*Contact factory for other voltage options. Output voltage range 1.0 V to 3.3 V with step 50 mV.
www.onsemi.com
13
NCP153
PACKAGE DIMENSIONS
XDFN6 1.20x1.20, 0.40P
CASE 711AT
ISSUE B
D
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO THE PLATED
TERMINALS.
4. COPLANARITY APPLIES TO THE PAD AS
WELL AS THE TERMINALS.
A
B
ÍÍÍ
ÍÍÍ
PIN ONE
REFERENCE
E
DIM
A
A1
b
D
D2
E
E2
e
L
L1
L
TOP VIEW
DETAIL A
OPTIONAL
CONSTRUCTION
A
0.05 C
A1
RECOMMENDED
MOUNTING FOOTPRINT*
0.05 C
NOTE 4
C
SIDE VIEW
SEATING
PLANE
1.08
PACKAGE
OUTLINE
D2
6X
1
3
MILLIMETERS
TYP
MAX
0.37
0.45
0.03
0.05
0.18
0.23
1.20
1.25
1.04
0.94
1.20
1.25
0.40
0.30
0.40 BSC
0.15
0.20
0.25
0.03
0.00
0.05
MIN
0.30
0.00
0.13
1.15
0.84
1.15
0.20
6X
0.37
L1
1.40
E2
6X
0.40
L
1
0.40
PITCH
6
DETAIL A
4
6X
0.24
DIMENSIONS: MILLIMETERS
6X
e
b
0.10
BOTTOM VIEW
M
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
C A B
NOTE 3
ZigBee is a registered trademark of ZigBee Alliance.
Bluetooth is a registered trademark of Bluetooth SIG.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
14
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP153/D