PIC18F2515/2610/4515/4610 PIC18F2515/2610/4515/4610 Rev. B5 Silicon Errata The PIC18F2515/2610/4515/4610 family Rev. B5 parts you have received conform functionally to the Device Data Sheet (DS39636C), except for the anomalies described below. Any Data Sheet Clarification issues related to the PIC18F2515/2610/4515/4610 family will be reported in a separate Data Sheet errata. Please check the Microchip web site for any existing issues. The following silicon errata apply only to PIC18F2515/2610/4515/4610 family devices with these Device/Revision IDs: Part Number Device ID Revision ID PIC18F2515 0000 1100 111 0 0111 PIC18F2610 0000 1100 101 0 0111 PIC18F4515 0000 1100 011 0 0111 PIC18F4610 0000 1100 001 0 0111 The Device IDs (DEVID1 and DEVID2) are located at addresses 3FFFFEh:3FFFFFh in the device’s configuration space. They are shown in binary in the format “DEVID2 DEVID1”. 1. Module: MSSP In SPI Slave mode, with slave select enabled (SSPM<3:0> = 0b0100), the minimum time between the falling edge of the SS pin and the first SCK edge is greater than specified in parameter 70 in Table 25-16. The updated specification is shown in bold in Table 1. The minimum time between the SS pin low and an SSPBUF write is also 3 TCY. If the falling edge of the SS pin occurs greater than 3 TCY before the first SCK edge or loading SSPBUF, the peripheral will function correctly. Also, if SSPBUF is written prior to the SS pin going low, the peripheral will function correctly. Work around None. Date Codes that pertain to this issue: All engineering and production devices. All of the issues listed here will be addressed in future revisions of the PIC18F2515/2610/4515/4610 family silicon. TABLE 1: Param No. 70 EXAMPLE SPI MODE REQUIREMENTS (SLAVE MODE TIMING, CKE = 0) Symbol Characteristic TSSL2SCH, SS↓ to SCK↓ or SCK↑ Input TSSL2SCL © 2008 Microchip Technology Inc. Min 3 TCY Max Units Conditions — ns DS80416A-page 1 PIC18F2515/2610/4515/4610 FAMILY 2. Module: MSSP With MSSP in SPI Master mode, FOSC/64 or Timer2/2 clock rate and CKE = 0, a write collision may occur if SSPBUF is loaded immediately after the transfer is complete. A delay may be required after the MSSP Interrupt Flag bit, SSPIF, is set or the Buffer Full bit, BF, is set and before writing SSPBUF. If the delay is insufficiently short, a write collision may occur as indicated by the WCOL bit being set. Work around 4. Module: Enhanced Universal Synchronous Receiver Transmitter (EUSART) One bit has been added to the BAUDCON register and one bit has been renamed. The added bit is RXDTP and is in the location, BAUDCON<5>. The renamed bit is the TXCKP bit (BAUDCON<4>), which had been named SCKP. The TXCKP (BAUDCON<4>) and RXDTP (BAUDCON<5>) bits enable the TX and RX signals to be inverted (polarity reversed). Add a software delay of one SCK period after detecting the completed transfer and prior to updating the SSPBUF contents. Verify the WCOL bit is clear after writing SSPBUF. If the WCOL is set, clear the bit in software and rewrite the SSPBUF register. Register 17-3, on page 194, will be changed as shown on page 3. Date Codes that pertain to this issue: All engineering and production devices. Work around None required. Date Codes that pertain to this issue: All engineering and production devices. 3. Module: Enhanced Capture/Compare/ PWM (ECCP) With the ECCP configured for Half-Bridge PWM mode (CCP1M<3:0> = 0b1110), the output may be corrupted for particular duty cycle selections. Affected duty cycle values are 0 though 3, and every subsequent increment of 4 (i.e., 7, 11, 15, 19, etc.). Work around None. Date Codes that pertain to this issue: All engineering and production devices. DS80416A-page 2 © 2008 Microchip Technology Inc. PIC18F2515/2610/4515/4610 FAMILY REGISTER 17-3: R/W-0 BAUDCON: BAUD RATE CONTROL REGISTER R-1 ABDOVF RCIDL R/W-0 RXDTP R/W-0 TXCKP R/W-0 U-0 R/W-0 R/W-0 BRG16 — WUE ABDEN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 ABDOVF: Auto-Baud Acquisition Rollover Status bit 1 = A BRG rollover has occurred during Auto-Baud Rate Detect mode (must be cleared in software) 0 = No BRG rollover has occurred bit 6 RCIDL: Receive Operation Idle Status bit 1 = Receive operation is Idle 0 = Receive operation is Active bit 5 RXDTP: Receive Data Polarity Select bit Asynchronous mode: 1 = Receive data (RX) is inverted. Idle state is a low level. 0 = No inversion of receive data (RX). Idle state is a high level. Synchronous mode: 1 = Data (DT) is inverted. Idle state is a low level. 0 = No inversion of data (DT). Idle state is a high level. bit 4 TXCKP: Transmit/Clock Polarity Select bit Asynchronous mode: 1 = Transmit data (TX) is inverted. Idle state is a low level. 0 = No inversion of transmit data (TX). Idle state is a high level. Synchronous mode: 1 = Idle state for clock (CK) is a high level 0 = Idle state for clock (CK) is a low level bit 3 BRG16: 16-bit Baud Rate Register Enable bit 1 = 16-bit Baud Rate Generator – SPBRGH and SPBRG 0 = 8-bit Baud Rate Generator – SPBRG only (Compatible mode); SPBRGH value ignored bit 2 Unimplemented: Read as ‘0’ bit 1 WUE: Wake-up Enable bit Asynchronous mode: 1 = EUSART will continue to sample the RX pin with the interrupt generated on the falling edge; bit cleared in hardware on following rising edge 0 = RX pin is not monitored or rising edge detected Synchronous mode: Unused in this mode. bit 0 ABDEN: Auto-Baud Detect Enable bit Asynchronous mode: 1 = Enable baud rate measurement on the next character. Requires reception of a Sync field (55h); cleared in hardware upon completion. 0 = Baud rate measurement disabled or completed Synchronous mode: Unused in this mode. © 2008 Microchip Technology Inc. DS80416A-page 3 PIC18F2515/2610/4515/4610 FAMILY 5. Module: Master Synchronous Serial Port (MSSP) When configured for I2C™ slave reception, the MSSP module may not receive the correct data, in extremely rare cases. This occurs only if the Serial Receive/Transmit Buffer Register (SSPBUF) is not read within a window after the SSPIF interrupt (PIR1<3>) has occurred. 6. Module: Enhanced Universal Synchronous Receiver Transmitter (EUSART) In rare situations, when interrupts are enabled, unexpected results may occur if: • The EUSART is disabled (the SPEN bit, RCSTA<7> = 0) • The EUSART is re-enabled (RCSTA<7> = 1) • A two-cycle instruction is executed Work around The issue can be resolved either of these ways: Work around • Prior to the I2C slave reception, enable the clock stretching feature. This is done by (SSPCON2<0>). setting the SEN Add a 2 TCY delay after re-enabling the EUSART. bit • Each time the SSPIF is set, read the SSPBUF before the first rising clock edge of the next byte being received. 1. 2. 3. 4. (This is the first TCY delay.) Date Codes that pertain to this issue: All engineering and production devices. Disable Receive Interrupts (RCIE bit, PIE1<5> = 0). Disable the EUSART (RCSTA<7> = 0). Re-enable the EUSART (RCSTA<7> = 1). Re-enable Receive Interrupts (PIE1<5> = 1). 5. Execute a NOP instruction. (This is the second TCY delay.) Date Codes that pertain to this issue: All engineering and production devices. DS80416A-page 4 © 2008 Microchip Technology Inc. PIC18F2515/2610/4515/4610 FAMILY REVISION HISTORY Rev A Document (10/2008) Initial release of this errata. Includes silicon issues 12 (MSSP), 3 (Enhanced Capture/Compare/PWM – ECCP), 4 (Enhanced Universal Synchronous Receiver Transmitter – EUSART), 5 (Master Synchronous Serial Port – MSSP) and 6 (Enhanced Universal Synchronous Receiver Transmitter – EUSART). © 2008 Microchip Technology Inc. DS80416A-page 5 PIC18F2515/2610/4515/4610 FAMILY NOTES: DS80416A-page 6 © 2008 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, Accuron, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, rfPIC and SmartShunt are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL, SmartSensor and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, In-Circuit Serial Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, PICkit, PICDEM, PICDEM.net, PICtail, PIC32 logo, PowerCal, PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total Endurance, UNI/O, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2008, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. © 2008 Microchip Technology Inc. DS80416A-page 7 WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-4182-8400 Fax: 91-80-4182-8422 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Hsin Chu Tel: 886-3-572-9526 Fax: 886-3-572-6459 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 01/02/08 DS80416A-page 8 © 2008 Microchip Technology Inc.