Download

Datasheet
Pre-configured Wireless Enclosures
NEW
Weidmuller is pleased to offer three pre-configured and
assembled Wireless Enclosure Solutions. These three
wireless enclosures feature plastic or metal enclosures with
either Wireless Ethernet Modems or Radio Frequency (RF)
Transmitters/Receivers. Just connect power and your signals and
you are wireless!
The Ethernet solution is available in both a stainless steel or
plastic enclosure, and features a Weidmuller wireless Ethernet
(WiFi) 2.4Ghz modem, which can function as an access point,
bridge, client or router.
In addition to the modem technology, the enclosure comes
complete with the following components: power supply, circuit
protection, surge protection, terminal blocks, ground blocks,
antenna, antenna connection cables and through panel cable
glands.
This complete, preassembled solution provides all the necessary
elements for a remote wireless Ethernet installation.
Representative photo
Weidmuller, Canada
10 Spy Court
Markham, Ontario L3R 5H6
Telephone: (800) 268-4080
Facsimile: (877) 300-5635
Email: [email protected]
Website: www.weidmuller.ca
Weidmuller, Mexico
Blvd. Hermanos Serdán 698,
Col. San Rafael Oriente
Puebla, Puebla, Mexico
C.P. 72029
Telephone: 01 222 2686267
Facsimile: 01 222 2686219
Email: [email protected]
Website: www.weidmuller.com.mx
Weidmuller, United States
821 Southlake Blvd.
Richmond, Virginia 23236
Telephone: (800) 849-9343
Facsimile: (804) 379-2593
Email: [email protected]
Website: www.weidmuller.com
Pre-configured Wireless Enclosures - Wireless Ethernet
Wireless Ethernet
Representative photo
Plastic Enclosure NEMA4X
• 2.4GHz (WiFi) Wireless Ethernet modem
• Operate as a Client/Bridge/Access Point/Router with a 400mW transmit power
• Built in Security/Encryption including AES,and WEP with matching antenna
and all cabling
• Assembled, wired, and tested!
• Surge protection included
• Transmit range up to 3 miles with appropriate antenna
• Data transmission rates up to 54Mbps
Ordering data
Type
Wireless Ethernet Enclosure – Plastic Solution
Dimensions mm/in (h x w x d)
Part No.
6760004617
356 x 305 x 212 / 14.02 x 12.01 x 8.35
Stainless Steel Enclosure NEMA4X
• 2.4GHz (WiFi) Wireless Ethernet modem
• Operate as a Client/Bridge/Access Point/Router with a 400mW transmit power
• Built in Security/Encryption including AES,and WEP with matching antenna
and all cabling
• Assembled, wired, and tested!
• Surge protection included
• Transmit range up to 3 miles with appropriate antenna
• Data transmission rates up to 54Mbps
Ordering data
Type
Wireless Ethernet Enclosure – Stainless Steel Solution
Dimensions mm/in (h x w x d)
2
Part No.
6760004616
356 x 305 x 212 / 14.02 x 12.01 x 8.35
Pre-configured Wireless Enclosures - Wireless Ethernet
Wireless Ethernet
WI-MOD-E-G
Ethernet 2.4GHz
WI-MOD-E-G
Ethernet 2.4GHz - Antenna
Technical data
Technical data
Description:
Ethernet
10/100 BaseT RJ45, IEEE 802.3
Bridge/router functions work with all Ethernet protocols
Maximum Power
25 watts
Vertical
Embedded Protocols:
TCP/IP, UDP ARP, SNMP, RADIUS/802.1X, DHCP, DNS,
PPP, ICMP, HTTP, FTP, TFTP, TELNET
Polarization
Nominal Impedance
50 ohms
VSWR across the band
< 1.5:1
Radome Material
UV resistant
pultruded
fiberglass
Termination
N female
Mounting Base Diameter
1.25"
Serial
RS232 V.24 DCE
1.2 to 230.4 Kb/s
Input
1.2 to 230.4 Kb/s
Serial server, PPP, Modbus to Modbus TCP conversion
One I/O channel (expandable with WI-I/O-EX-1-S-XX
units)
voltage-free contact
Output
FET 30VDC 500mA
Networking
Configurable as Access Point or Client, Bridge or Router
Point-to-Point, Point-to-Multipoint, user configurable
addressing WDS Mesh repeater functionality
MAC Filtering – whitelist or blacklist.
Serial gateway TELNET
Modbus TCP/RTU Gateway
RS485
Discrete I/O
General Data
Operating
Temperature
-40 to +60°C (-40 to +140°F)
Humidity
99% non-condensing
Power Supply
9 – 30VDC
Idle: 12V-270mA; 24V - 140mA
Transmit: 12V - 470mA; 24V - 250mA
FCC Part 15.247, CE ETS 300 328, RSS 210,
Hazardous area Class 1 Div 2, IEC 60950
DIN rail mounting
Current consumption
Approvals
Mounting
LED indication
Electrical Specifications
Frequency Range
2.4 - 2.48 GHz
Gain
Half Power Vertical
Beamwidth
Mechanical Specifications
4 dBi
Antenna Type
Omni
Connector Type
N female
Antenna Height
8.1" (205.7 mm)
Bending Moment at
Rated Wind
0.7 ft-lbs
Max wind load
@ rated velocity
2.1 lbs
Equivalent Flat Plate Area
.02 ft2
Rated Wind
125 mph
Weight lbs (kg)
0.34 (0.154)
Temperature Range
-40°C to +70°C
30°
Power / OK, Radio Rx and Tx, Radio Link, LAN link /
Activity , Serial Activity, Digital I/O
Dimensions mm (in) 115 x 165 x 32 (4.5 x 6.5 x 1.4)
Weight
< 1 lb / 0.5 kg
Wireless
2.414 – 2.462GHz Direct Sequence Spread Spectrum
(DSSS), 11 x 5MHz Channel Spacing
802.11b/g compliant, auto rate selection 1 - 108 Mb/s,
OFDMcompliant
WI-ACC-2-6GHZ
SURGE NF-NF
Surge Suppressor
Radio Transceiver
Transmit Power
1 - 24Mb/s @ 400mW (+26dBm); -54Mb/s @ 125mW
(+21dBm), dependent on local regulations
Receiver sensitivity
97dBm @ 1Mb/s, -74dBm @ 54Mb/s < 8% FER
Radio range
1km @ 100mW; 3 miles / 5km @ 400 mW
Range may be extended using repeater features
Antenna connection
Dual SMA female coaxial
Security
Data Encryption 64 / 128 bit WEP - WPA2 PSK - 802.1
1i - 802.1x MAC Address filtering; IP filtering; ARP
filteringPassword protected configuration
Technical data
Configuration
HTTP with remote configuration via wireless link
Web based system management - RF signal strength,
Bit Error Rate, connection monitoring and statistics
Connector
N female to N
female
Frequency Range
2.0 - 6.0 GHz
Diagnostics
PPP Protocol Access to diagnostics
Firmware upgradeable via serial port
VSWR
1.3: 1
Insertion Loss
0.1 dB
Turn-on
3
Pre-configured Wireless Enclosures - Wireless I/O
Wireless I/O
Wireless I/O 900MHz
The I/O version is comprised of two pre-assembled plastic enclosures. Each enclosure
contains a power supply, circuit protection, surge protection, antenna, antenna
connection cables and terminal blocks.
In addition to these components, one enclosure houses a transmitter, and the second
enclosure houses a receiver. The transmitter and receiver operate on 900Mhz radio
bands, and are preconfigured to send and receive multiple I/O signals. The I/O
solution can transmit and receive two digital signals and one analog signal over a
range of several miles.
This self-contained solution is designed for quick and easy set-up. The pre-installed
terminals make I/O and power connections fast and easy, for “out of the box”
operation.
Features:
• Two pre-assembled NEMA4x Plastic Enclosures
• 900MHz (Frequency Hopping) Transmitter and
Receiver with a 1W transmit power
• Preconfigured and mapped I/O
with matching antenna and all cabling
• Surge protection included
• Cable glands included for signal and power access
• Assembled, wired, and tested!
• Transmit range up to 20 miles with appropriate antenna
• Transmitter accepts up to 1 analog and 2 digital intputs
• Receiver accepts up to 1 analog and 2 digital outputs
Ordering data
Type
Wireless I/O 900MHz - Plastic Solution
Dimensions mm/in (h x w x d)
4
Part No.
6760004618
307 x 256 x 162 / 12.08 x 10.09 x 6.38
Pre-configured Wireless Enclosures - Wireless I/O
Wireless I/O
WI-I/O 9-L-T Transmitter
C
WI-I/O 9-L-R Receiver
C1D2
C
US
C1D2
US
Technical data
Transmitter Inputs:
Digital:
Pulse:
Analog:
two inputs, suitable for voltage free contacts / NPN,
or voltage input 0-1 VDC on / >3 VDC off
max rate 10 Hz, 50 msec on time.
Pulse counted as 16 bit register.
0-20 mA (4-20mA, 0-10mA)
“floating” differential input:
resolution
16 bit
accuracy
< 0.1 %
Thermocouple
Millivolt (-100mV to +100mV), J, K or T type linearization
with on-board cold-junction compensation
Accuracy
greater than 1°C
Receiver Outputs
Digital
three relay contact outputs, 260V 1A
Analog
0-20mA
resolution
12 bit
accuracy
0.10%
Power Supply
9-30 VDC
Internal status based on configurable time-out value.
Comms-fail status can be configured to a local output.
On “comms-fail”, outputs user-configurable as retained
(last correct value) or reset (fail-safe)
9-30 VDC
Power consumption @12VDC
Receiver 100mA, Transmitter 40mA quiescent,
during radio transmission (50 msec) 300mA
Receiver 100mA, Transmitter 40mA quiescent, during
radio transmission (50 msec) 300mA
Analog loop supply internally generated
24VDC 30mA
24VDC 30mA
Internal monitoring of supply low voltage status
may be transmitted as an “input” (Transmitter unit only)
Comms-Fail
Fail-safe
Power consumption increases for pulse inputs > 10Hz.
Serial Port
RS232 RJ45 female DCE, used for configuration
and diagnostics
RS232 RJ45 female DCE, used for configuration
and diagnostics
General Data
Operating Temperature
-40 to 60°C (-40 to 140°F)
-40 to 60°C (-40 to 140°F)
Humidity
0 - 99% RH
0 - 99% RH
EMC Standards
FCC Part 15.247, RS210
FCC Part 15.247, RS210
Mounting
DIN-rail mounting
DIN-rail mounting
LED indication: Transmitter Unit
Power/OK, Radio TX, DIN1, DIN2, Analog Setpoint status
LED indication: Receiver Unit
frequency hopping spread spectrum
Power/OK, Radio RX, DO1, DO2, DO3, Communications Fail.
902-928MHz, sub-bands available
902-928MHz, sub-bands available
Transmit power
1W
1W
Maximum line of sight range
20 miles (4W ERP), 15km (1W ERP); 3000 ft / 1000 m
in obstructed industrial environments. Radio distances
can be increased by up to 5 intermediate repeater
units. Each transmission may be configured to be sent
1 to 5 times.
20 miles (4W ERP), 15km (1W ERP); 3000 ft / 1000 m
in obstructed industrial environments. Radio distances
can be increased by up to 5 intermediate repeater
units. Each transmission may be configured to be sent
1 to 5 times.
Antenna connector
SMA female coaxial
SMA female coaxial
Dimensions mm (in)
100 x 23 x 120 (3.9 x 0.9 x 4.7)
User configuration via serial port. Unidirectional units
can be configured to network with Multi-I/O and
Gateway units.
Diagnostics features - read input values, write output
values, radio signal strength, monitor communication
messages.
100 x 23 x 120 (3.9 x 0.9 x 4.7)
User configuration via serial port. Unidirectional units
can be configured to network with Multi-I/O and
Gateway units.
Diagnostics features - read input values, write output
values, radio signal strength, monitor communication
messages.
Configuration
Diagnostics
5
Pre-configured Wireless Enclosures - Accessories
Antennas
WI-ANT-DPL-0-16
Representative Photo
Technical data
Maximum Power
10 watts
Polarization
vertical
Nominal Impedance
50 ohms
VSWR across the band
<1.5: 1
Radome Material
Fiberglass
Termination
SMA male
Mounting Base Diameter
Electrical Specifications
Frequency Range
853-930 MHz
Gain
0 dBi
Half Power Vertical Beamwidth
Mechanical Specifications
Antenna Type
Half wave dipole
Connector Type
SMA male
Antenna Height
16" (40 cm)
Bending Moment at Rated Wind
Max Wind Load @ Rated Velocity
Equivalent Flat Plate Area
Rated Wind
Weight lbs (kg)
0.5 (0.2)
Temperature Range
Surge Suppressor
WI-DIV-CCMA SMA M – SMA F
Technical data
Connector
SMA Male to SMA Female
Frequency Range
<1200 MHz
VSWR
Insertion Loss
Turn-on
6
<0.2dB over range
Pre-configured Wireless Enclosures
connectPower
single-phase
Circuit Breakers
Thermal Magnetic Type -
CP SNT 48 W 24 V 2 A
CB4200 Series Single Pole
D
W
L
AC/DC
N
H
L
+
PWM
FUSE
N
DC
+
−
–
Technical data
Input
Input voltage
85...264 V AC / 110...370 V DC
Input current
500 mA at rated load @ 230 V AC
Input frequency
50/ 60 Hz
Turn-on current limit
Yes
Input fuse
Fusible link 2.5 A (T) / 250 V
Surge protection
• Rated from 0.05 to 16.0 amps
• Available in single or double pole
configurations
• Features a tease free design to reduce
contact damage
• Offers push button trip/reset function
• Trip free design means the breaker
cannot be held closed against a fault
• Mounts on 32mm or 35mm DIN-rail
• UL 1077 recognized
• CSA C22.2 No. 235
Output
Output voltage
15...28 V DC (adjustable via potentiometer)
Output current
2A
Output power
48 W
Max. residual ripple
120 mVSS
Overload protection
105 %...150 % Iconst of max. output load;
automatic reset
Surge protection
Varistor
Mains failure bridge-over time
11 ms @ 115 V AC / 50 ms @ 230 V AC
Control at 10...100% load
1%
Max. capacitance at output
10000 µF
Insulation coordination (EN 50178)
Trip Curves
Thermal Magnetic Type
Typical time/current
characteristics at 23°C
M1+
M1+ 0.050.05
to 7.5 to
A 7.5 A
10,000
–30°C
+23°C
+55°C
1,000
0.5 kV
Electrical isolation, input-earth
1.5 kV
Electrical isolation, input-output
3 kV
Electrical isolation, I/O rail
4 kV
General data
Ambient temperature (operational)
-10...+70 °C (Derating ab 55 °C)
Storage temperature
-20 °C...+85 °C
Degree of efficiency at max. load
78%
Standards
DIN EN 50178 (PELV), DIN EN 60950 (SELV)
Approvals
cCSAus; cULus; cURus; GOSTME25; UL
EMC standards
EN 55011, EN 55022, EN 61000-3-2,-3,
EN 61000-6-2,-3,-4
Dimensions
Input/Output
Clamping range (nominal / min. / max.)
mm²
2.5 / 0.5 / 4
Height x width x depth
mm
90.5 / 70 / 62.5
The internal varistor found in a switch-mode power supply does
not replace the need for surge protection within a system.
Notes
100
Trip time in seconds
Electrical isolation, output-earth
10
1
0.1
0.01
0.001
0.8 1
2
3
4
6
8 10
20 30
50 70 100
… times rated current
Derating curve
Derating curve
3
Current (A)
2.5
2
1.5
1
0.5
0
0
10
20 30 40 50 60
Ambient temperature (°C)
70
80
7
Pre-configured Wireless Enclosures
8
Subject to technical changes · 05/13 · X.XM · LIT1320