MOSFET 1 Amp, 62 Volts, Logic Level

MLP1N06CL
Preferred Device
SMARTDISCRETES MOSFET
1 Amp, 62 Volts, Logic Level
N–Channel TO–220
These SMARTDISCRETES devices feature current limiting for
short circuit protection, an integral gate–to–source clamp for ESD
protection and gate–to–drain clamp for over–voltage protection. No
additional gate series resistance is required when interfacing to the
output of a MCU, but a 40 kΩ gate pulldown resistor is recommended
to avoid a floating gate condition.
The internal gate–to–source and gate–to–drain clamps allow the
devices to be applied without use of external transient suppression
components. The gate–to–source clamp protects the MOSFET input
from electrostatic gate voltage stresses up to 2.0 kV. The gate–to–drain
clamp protects the MOSFET drain from drain avalanche stresses that
occur with inductive loads. This unique design provides voltage
clamping that is essentially independent of operating temperature.
• Temperature Compensated Gate–to–Drain Clamp Limits Voltage
Stress Applied to the Device and Protects the Load From
Overvoltage
• Integrated ESD Diode Protection
• Controlled Switching Minimizes RFI
• Low Threshold Voltage Enables Interfacing Power Loads to
Microprocessors
http://onsemi.com
1 AMPERE
62 VOLTS (Clamped)
RDS(on) = 750 mΩ
N–Channel
R1
G
R2
S
MARKING DIAGRAM
& PIN ASSIGNMENT
MAXIMUM RATINGS (TC = 25°C unless otherwise noted)
Rating
D
Symbol
Value
Unit
Drain–to–Source Voltage
VDSS
Clamped
Vdc
Drain–to–Gate Voltage
(RGS = 1.0 MΩ)
VDGR
Clamped
Vdc
Gate–to–Source Voltage – Continuous
VGS
±10
Vdc
Drain Current – Continuous
Drain Current – Single Pulse
ID
IDM
Self–limited
1.8
Adc
Total Power Dissipation
PD
40
Watts
Electrostatic Discharge Voltage
(Human Body Model)
ESD
2.0
kV
Operating and Storage Junction
Temperature Range
TJ, Tstg
–50 to 150
°C
THERMAL CHARACTERISTICS
Thermal Resistance, Junction to Case
Thermal Resistance, Junction to
Ambient
RθJC
RθJA
3.12
62.5
°C/W
Maximum Lead Temperature for
Soldering Purposes, 1/8″ from case
TL
260
°C
4
Drain
4
TO–220AB
CASE 221A
STYLE 5
1
2
L1N06CL
LLYWW
1
Gate
3
3
Source
2
Drain
L1N06CL
LL
Y
WW
= Device Code
= Location Code
= Year
= Work Week
ORDERING INFORMATION
Device
MLP1N06CL
Package
Shipping
TO–220AB
50 Units/Rail
Preferred devices are recommended choices for future use
and best overall value.
 Semiconductor Components Industries, LLC, 2000
November, 2000 – Rev. 2
1
Publication Order Number:
MLP1N06CL/D
MLP1N06CL
UNCLAMPED DRAIN–TO–SOURCE AVALANCHE CHARACTERISTICS
Rating
Single Pulse Drain–to–Source Avalanche Energy
(Starting TJ = 25°C, ID = 2.0 A, L = 40 mH) (Figure 6)
Symbol
Value
Unit
EAS
80
mJ
ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted)
Characteristic
Symbol
Min
Typ
Max
59
59
62
62
65
65
–
–
0.6
6.0
5.0
20
–
–
0.5
1.0
5.0
20
1.0
0.6
1.5
–
2.0
1.6
–
–
–
–
0.63
0.59
1.1
1.0
0.75
0.75
1.9
1.8
Unit
OFF CHARACTERISTICS
Drain–to–Source Sustaining Voltage (Internally Clamped)
(ID = 20 mA, VGS = 0)
(ID = 20 mA, VGS = 0, TJ = 150°C)
V(BR)DSS
Zero Gate Voltage Drain Current
(VDS = 45 V, VGS = 0)
(VDS = 45 V, VGS = 0, TJ = 150°C)
IDSS
Gate–Body Leakage Current
(VG = 5.0 V, VDS = 0)
(VG = 5.0 V, VDS = 0, TJ = 150°C)
IGSS
Vdc
µAdc
µAdc
ON CHARACTERISTICS (Note 1.)
Gate Threshold Voltage
(ID = 250 µA, VDS = VGS)
(ID = 250 µA, VDS = VGS, TJ = 150°C)
VGS(th)
Static Drain–to–Source On–Resistance
(ID = 1.0 A, VGS = 4.0 V)
(ID = 1.0 A, VGS = 5.0 V)
(ID = 1.0 A, VGS = 4.0 V, TJ = 150°C)
(ID = 1.0 A, VGS = 5.0 V, TJ = 150°C)
RDS(on)
Vdc
Ohms
Forward Transconductance (ID = 1.0 A, VDS = 10 V)
gFS
1.0
1.4
–
mhos
Static Source–to–Drain Diode Voltage (IS = 1.0 A, VGS = 0)
VSD
–
1.1
1.5
Vdc
2.0
1.1
2.3
1.3
2.75
1.8
td(on)
–
1.2
2.0
tr
–
4.0
6.0
td(off)
–
4.0
6.0
tf
–
3.0
5.0
Static Drain Current Limit
(VGS = 5.0 V, VDS = 10 V)
(VGS = 5.0 V, VDS = 10 V, TJ = 150°C)
ID(lim)
A
RESISTIVE SWITCHING CHARACTERISTICS (Note 1.)
Turn–On Delay Time
Rise Time
Turn–Off Delay Time
(VDD = 25 V, ID = 1.0 A,
VGS = 5.0 V, RG = 50 Ohms)
Fall Time
1. Indicates Pulse Test: Pulse Width ≤ 300 µs, Duty Cycle ≤ 2.0%.
http://onsemi.com
2
µs
MLP1N06CL
4
3
10 V
6V
8V
4V
2
VGS = 3 V
1
0
0
2
4
6
VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS)
VDS ≥ 7.5 V
4
ID , DRAIN CURRENT (AMPS)
ID , DRAIN CURRENT (AMPS)
TJ = 25°C
3
25°C
2
TJ = 150°C
1
0
8
-50°C
0
Figure 1. Output Characteristics
2
4
6
VGS, GATE-TO-SOURCE VOLTAGE (VOLTS)
8
Figure 2. Transfer Function
THE SMARTDISCRETES CONCEPT
SHORT CIRCUIT PROTECTION AND THE EFFECT OF
TEMPERATURE
From a standard power MOSFET process, several active
and passive elements can be obtained that provide on–chip
protection to the basic power device. Such elements require
only a small increase in silicon area and/or the addition of one
masking layer to the process. The resulting device exhibits
significant improvements in ruggedness and reliability as
well as system cost reduction. The SMARTDISCRETES
device functions can now provide an economical alternative
to smart power ICs for power applications requiring low
on–resistance, high voltage and high current.
These devices are designed for applications that require a
rugged power switching device with short circuit protection
that can be directly interfaced to a microcontroller unit
(MCU). Ideal applications include automotive fuel injector
driver, incandescent lamp driver or other applications where
a high in–rush current or a shorted load condition could occur.
The on–chip circuitry of the MLP1N06CL offers an
integrated means of protecting the MOSFET component
from high in–rush current or a shorted load. As shown in the
schematic diagram, the current limiting feature is provided
by an NPN transistor and integral resistors R1 and R2. R2
senses the current through the MOSFET and forward biases
the NPN transistor’s base as the current increases. As the
NPN turns on, it begins to pull gate drive current through R1,
dropping the gate drive voltage across it, and thus lowering
the voltage across the gate–to–source of the power
MOSFET and limiting the current. The current limit is
temperature dependent as shown in Figure 3, and decreases
from about 2.3 Amps at 25°C to about 1.3 Amps at 150°C.
Since the MLP1N06CL continues to conduct current and
dissipate power during a shorted load condition, it is
important to provide sufficient heatsinking to limit the
device junction temperature to a maximum of 150°C.
The metal current sense resistor R2 adds about 0.4 ohms
to the power MOSFET’s on–resistance, but the effect of
temperature on the combination is less than on a standard
MOSFET due to the lower temperature coefficient of R2.
The on–resistance variation with temperature for gate
voltages of 4 and 5 Volts is shown in Figure 5.
Back–to–back polysilicon diodes between gate and
source provide ESD protection to greater than 2 kV, HBM.
This on–chip protection feature eliminates the need for an
external Zener diode for systems with potentially heavy line
transients.
OPERATION IN THE CURRENT LIMIT MODE
The amount of time that an unprotected device can
withstand the current stress resulting from a shorted load
before its maximum junction temperature is exceeded is
dependent upon a number of factors that include the amount
of heatsinking that is provided, the size or rating of the
device, its initial junction temperature, and the supply
voltage. Without some form of current limiting, a shorted
load can raise a device’s junction temperature beyond the
maximum rated operating temperature in only a few
milliseconds.
Even with no heatsink, the MLP1N06CL can withstand a
shorted load powered by an automotive battery (10 to 14
Volts) for almost a second if its initial operating temperature
is under 100°C. For longer periods of operation in the
current–limited mode, device heatsinking can extend
operation from several seconds to indefinitely depending on
the amount of heatsinking provided.
http://onsemi.com
3
MLP1N06CL
4
VGS=5V
VDS=7.5V
R DS(on), ON-RESISTANCE (OHMS)
ID(lim) , DRAIN CURRENT (AMPS)
4
3
2
1
3
2
25°C
0
50
100
TJ, JUNCTION TEMPERATURE (°C)
150
0
150°C
2
4
6
8
VGS, GATE-TO-SOURCE VOLTAGE (VOLTS)
10
Figure 4. RDS(on) Variation With
Gate–To–Source Voltage
Figure 3. ID(lim) Variation With Temperature
1.25
RDS(on), ON-RESISTANCE (OHMS)
TJ=-50°C
1
0
0
-50
ID = 1 A
ID = 1 A
1
VGS = 4 V
0.75
VGS=5 V
0.5
0.25
-50
0
50
100
TJ, JUNCTION TEMPERATURE (°C)
150
BV(DSS) , DRAIN-SOURCE SUSTAINING VOLTAGE (VOLTS)
WAS , SINGLE PULSE AVALANCHE ENERGY (mJ)
Figure 5. On–Resistance Variation With
Temperature
100
80
60
40
20
0
25
50
75
100
125
TJ, JUNCTION TEMPERATURE (°C)
150
64
63
62
61
60
-50
Figure 6. Single Pulse Avalanche Energy
versus Junction Temperature
0
50
100
TJ, JUNCTION TEMPERATURE (°C)
Figure 7. Drain–Source Sustaining
Voltage Variation With Temperature
http://onsemi.com
4
150
MLP1N06CL
FORWARD BIASED SAFE OPERATING AREA
(1.8 A at 150°C) and not the RDS(on). The maximum voltage
can be calculated by the following equation:
The FBSOA curves define the maximum drain–to–source
voltage and drain current that a device can safely handle
when it is forward biased, or when it is on, or being turned
on. Because these curves include the limitations of
simultaneous high voltage and high current, up to the rating
of the device, they are especially useful to designers of linear
systems. The curves are based on a case temperature of 25°C
and a maximum junction temperature of 150°C. Limitations
for repetitive pulses at various case temperatures can be
determined by using the thermal response curves. ON
Semiconductor Application Note, AN569, “Transient
Thermal Resistance – General Data and Its Use” provides
detailed instructions.
(150 – TA)
ID(lim) (RθJC + RθCA)
Vsupply =
where the value of RθCA is determined by the heatsink that
is being used in the application.
DUTY CYCLE OPERATION
When operating in the duty cycle mode, the maximum
drain voltage can be increased. The maximum operating
temperature is related to the duty cycle (DC) by the
following equation:
TC = (VDS x ID x DC x RθCA) + TA
MAXIMUM DC VOLTAGE CONSIDERATIONS
The maximum value of VDS applied when operating in a
duty cycle mode can be approximated by:
The maximum drain–to–source voltage that can be
continuously applied across the MLP1N06CL when it is in
current limit is a function of the power that must be
dissipated. This power is determined by the maximum
current limit at maximum rated operating temperature
VDS =
150 – TC
ID(lim) x DC x RθJC
10
I D , DRAIN CURRENT (AMPS)
6
ID(lim)-MAX
3
2
1.5
ms
5ms
ID(lim)-MIN
1ms
dc
1
0.6
DEVICE/POWER LIMITED
RDS(on) LIMITED
0.3
VGS=5V
SINGLE PULSE
TC = 25°C
0.1
1
2
3
0.2
6
10
20
30
60
100
VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS)
r(t), EFFECTIVE TRANSIENT THERMAL
RESISTANCE (NORMALIZED)
Figure 8. Maximum Rated Forward Bias
Safe Operating Area (MLP1N06CL)
1.0
0.7
0.5
D = 0.5
0.3
0.2
0.2
0.1
0.07
0.05
0.03
0.02
0.01
0.01
RθJC(t) = r(t) RθJC
RθJC(t) = 3.12°C/W Max
D Curves Apply for Power
Pulse Train Shown
Read Time at t1
TJ(pk) - TC = P(pk) RθJC(t)
0.1
0.05
0.02
P(pk)
t1
0.01
t2
DUTY CYCLE, D =t1/t2
SINGLE PULSE
0.02 0.03 0.05
0.1
0.2
0.3
0.5
1.0
2.0
3.0
5.0
10
20
t, TIME (ms)
Figure 9. Thermal Response (MLP1N06CL)
http://onsemi.com
5
30
50
100
200 300
500 1000
MLP1N06CL
ton
VDD
RL
PULSE GENERATOR
Rgen
50Ω
Vin
td(on)
Vout
DUT
td(off)
tr
90%
OUTPUT, Vout
INVERTED
z = 50 Ω
toff
tf
90%
10%
90%
50 Ω
50%
INPUT, Vin
Figure 10. Switching Test Circuit
10%
50%
PULSE WIDTH
Figure 11. Switching Waveforms
ACTIVE CLAMPING
MLP1N06CL, the integrated gate–to–source voltage
elements provide greater than 2.0 kV electrostatic voltage
protection.
The avalanche voltage of the gate–to–drain voltage clamp
is set less than that of the power MOSFET device. As soon
as the drain–to–source voltage exceeds this avalanche
voltage, the resulting gate–to–drain Zener current builds a
gate voltage across the gate–to–source impedance, turning
on the power device which then conducts the current. Since
virtually all of the current is carried by the power device, the
gate–to–drain voltage clamp element may be small in size.
This technique of establishing a temperature compensated
drain–to–source sustaining voltage (Figure 7) effectively
removes the possibility of drain–to–source avalanche in the
power device.
The gate–to–drain voltage clamp technique is particularly
useful for snubbing loads where the inductive energy would
otherwise avalanche the power device. An improvement in
ruggedness of at least four times has been observed when
inductive energy is dissipated in the gate–to–drain clamped
conduction mode rather than in the more stressful
gate–to–source avalanche mode.
SMARTDISCRETES technology can provide on–chip
realization of the popular gate–to–source and gate–to–drain
Zener diode clamp elements. Until recently, such features
have been implemented only with discrete components
which consume board space and add system cost. The
SMARTDISCRETES technology approach economically
melds these features and the power chip with only a slight
increase in chip area.
In practice, back–to–back diode elements are formed in a
polysilicon region monolithicly integrated with, but
electrically isolated from, the main device structure. Each
back–to–back diode element provides a temperature
compensated voltage element of about 7.2 volts. As the
polysilicon region is formed on top of silicon dioxide, the
diode elements are free from direct interaction with the
conduction regions of the power device, thus eliminating
parasitic electrical effects while maintaining excellent
thermal coupling.
To achieve high gate–to–drain clamp voltages, several
voltage elements are strung together; the MLP1N06CL uses
8 such elements. Customarily, two voltage elements are used
to provide a 14.4 volt gate–to–source voltage clamp. For the
TYPICAL APPLICATIONS: INJECTOR DRIVER, SOLENOIDS, LAMPS, RELAY COILS
VBAT
The MLP1N06CL has been designed to allow direct
interface to the output of a microcontrol unit to control an
isolated load. No additional series gate resistance is
required, but a 40 kΩ gate pulldown resistor is
recommended to avoid a floating gate condition in the event
of an MCU failure. The internal clamps allow the device to
be used without any external transistent suppressing
components.
VDD
D
MCU
G
MLP1N06CL
S
http://onsemi.com
6
MLP1N06CL
PACKAGE DIMENSIONS
TO–220 THREE–LEAD
TO–220AB
CASE 221A–09
ISSUE AA
SEATING
PLANE
–T–
B
C
F
T
S
4
DIM
A
B
C
D
F
G
H
J
K
L
N
Q
R
S
T
U
V
Z
A
Q
1 2 3
U
H
K
Z
L
R
V
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION Z DEFINES A ZONE WHERE ALL
BODY AND LEAD IRREGULARITIES ARE
ALLOWED.
J
G
D
N
INCHES
MIN
MAX
0.570
0.620
0.380
0.405
0.160
0.190
0.025
0.035
0.142
0.147
0.095
0.105
0.110
0.155
0.018
0.025
0.500
0.562
0.045
0.060
0.190
0.210
0.100
0.120
0.080
0.110
0.045
0.055
0.235
0.255
0.000
0.050
0.045
----0.080
STYLE 5:
PIN 1.
2.
3.
4.
http://onsemi.com
7
GATE
DRAIN
SOURCE
DRAIN
MILLIMETERS
MIN
MAX
14.48
15.75
9.66
10.28
4.07
4.82
0.64
0.88
3.61
3.73
2.42
2.66
2.80
3.93
0.46
0.64
12.70
14.27
1.15
1.52
4.83
5.33
2.54
3.04
2.04
2.79
1.15
1.39
5.97
6.47
0.00
1.27
1.15
----2.04
MLP1N06CL
SMARTDISCRETES is a trademark of Semiconductor Components Industries, LLC (SCILLC).
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
NORTH AMERICA Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: [email protected]
Fax Response Line: 303–675–2167 or 800–344–3810 Toll Free USA/Canada
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
EUROPE: LDC for ON Semiconductor – European Support
German Phone: (+1) 303–308–7140 (Mon–Fri 2:30pm to 7:00pm CET)
Email: ONlit–[email protected]
French Phone: (+1) 303–308–7141 (Mon–Fri 2:00pm to 7:00pm CET)
Email: ONlit–[email protected]
English Phone: (+1) 303–308–7142 (Mon–Fri 12:00pm to 5:00pm GMT)
Email: [email protected]
CENTRAL/SOUTH AMERICA:
Spanish Phone: 303–308–7143 (Mon–Fri 8:00am to 5:00pm MST)
Email: ONlit–[email protected]
Toll–Free from Mexico: Dial 01–800–288–2872 for Access –
then Dial 866–297–9322
ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support
Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time)
Toll Free from Hong Kong & Singapore:
001–800–4422–3781
Email: ONlit–[email protected]
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Phone: 81–3–5740–2700
Email: [email protected]
ON Semiconductor Website: http://onsemi.com
EUROPEAN TOLL–FREE ACCESS*: 00–800–4422–3781
*Available from Germany, France, Italy, UK, Ireland
For additional information, please contact your local
Sales Representative.
http://onsemi.com
8
MLP1N06CL/D